1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
|
/****************************************************************************
* drivers/wireless/cc1101/ISM2_905MHzGFSK250kbps.c
*
* Copyright (C) 2011 Uros Platise. All rights reserved.
* Copyright (C) 2011 Ales Verbic. All rights reserved.
*
* Authors: Uros Platise <uros.platise@isotel.eu>
* Ales Verbic <ales.verbic@isotel.eu>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#include <nuttx/wireless/cc1101.h>
/** Settings for 905 MHz, GFSK at 250kbps
*
* ISM Region 2 (America) only, Band 902–928 MHz
*
* Cordless phones 1 W
* Microwave ovens 750 W
* Industrial heaters 100 kW
* Military radar 1000 kW
*
* Deviation = 126.953125
* Base frequency = 901.999969
* Carrier frequency = 905.998993
* Channel number = 20
* Carrier frequency = 905.998993
* Modulated = true
* Modulation format = GFSK
* Manchester enable = false
* Sync word qualifier mode = 30/32 sync word bits detected
* Preamble count = 4
* Channel spacing = 199.951172
* Carrier frequency = 905.998993
* Data rate = 249.939
* RX filter BW = 541.666667
* Data format = Normal mode
* Length config = Variable packet length mode. Packet length configured by the first byte after sync word
* CRC enable = true
* Packet length = 61
* Device address = 0
* Address config = No address check
* CRC autoflush = false
* PA ramping = false
* TX power = 0
*/
const struct c1101_rfsettings_s cc1101_rfsettings_ISM2_905MHzGFSK250kbps = {
.FSCTRL1 = 0x0C, // FSCTRL1 Frequency Synthesizer Control
.FSCTRL0 = 0x00, // FSCTRL0 Frequency Synthesizer Control
.FREQ2 = 0x22, // FREQ2 Frequency Control Word, High Byte
.FREQ1 = 0xB1, // FREQ1 Frequency Control Word, Middle Byte
.FREQ0 = 0x3B, // FREQ0 Frequency Control Word, Low Byte
.MDMCFG4 = 0x2D, // MDMCFG4 Modem Configuration
.MDMCFG3 = 0x3B, // MDMCFG3 Modem Configuration
.MDMCFG2 = 0x13, // MDMCFG2 Modem Configuration
.MDMCFG1 = 0x22, // MDMCFG1 Modem Configuration
.MDMCFG0 = 0xF8, // MDMCFG0 Modem Configuration
.DEVIATN = 0x62, // DEVIATN Modem Deviation Setting
.FOCCFG = 0x1D, // FOCCFG Frequency Offset Compensation Configuration
.BSCFG = 0x1C, // BSCFG Bit Synchronization Configuration
.AGCCTRL2= 0xC7, // AGCCTRL2 AGC Control
.AGCCTRL1= 0x00, // AGCCTRL1 AGC Control
.AGCCTRL0= 0xB0, // AGCCTRL0 AGC Control
.FREND1 = 0xB6, // FREND1 Front End RX Configuration
.FREND0 = 0x10, // FREND0 Front End TX Configuration
.FSCAL3 = 0xEA, // FSCAL3 Frequency Synthesizer Calibration
.FSCAL2 = 0x2A, // FSCAL2 Frequency Synthesizer Calibration
.FSCAL1 = 0x00, // FSCAL1 Frequency Synthesizer Calibration
.FSCAL0 = 0x1F, // FSCAL0 Frequency Synthesizer Calibration
.CHMIN = 0, // VERIFY REGULATIONS!
.CHMAX = 0xFF,
.PAMAX = 8, // 0 means power OFF, 8 represents PA[7]
.PA = {0x03, 0x0E, 0x1E, 0x27, 0x39, 0x8E, 0xCD, 0xC0}
};
|
