/****************************************************************************
* arch/arm/src/lpc17xx/lpc17_spi.c
*
* Copyright (C) 2010, 2012-2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include <semaphore.h>
#include <errno.h>
#include <debug.h>
#include <arch/board/board.h>
#include <nuttx/arch.h>
#include <nuttx/spi/spi.h>
#include "up_internal.h"
#include "up_arch.h"
#include "chip.h"
#include "chip/lpc17_syscon.h"
#include "lpc17_gpio.h"
#include "lpc17_spi.h"
#ifdef CONFIG_LPC17_SPI
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* This driver does not support the SPI exchange method. */
#ifdef CONFIG_SPI_EXCHANGE
# error "CONFIG_SPI_EXCHANGE must not be defined in the configuration"
#endif
/* Debug ********************************************************************/
/* The following enable debug output from this file:
*
* CONFIG_DEBUG - Define to enable general debug features
* CONFIG_DEBUG_SPI - Define to enable basic SSP debug (needs CONFIG_DEBUG)
* CONFIG_DEBUG_VERBOSE - Define to enable verbose SSP debug
*/
#ifdef CONFIG_DEBUG_SPI
# define spidbg lldbg
# ifdef CONFIG_DEBUG_VERBOSE
# define spivdbg lldbg
# else
# define spivdbg(x...)
# endif
#else
# define spidbg(x...)
# define spivdbg(x...)
#endif
/* SSP Clocking *************************************************************/
/* The CPU clock by 1, 2, 4, or 8 to get the SPI peripheral clock (SPI_CLOCK).
* SPI_CLOCK may be further divided by 8-254 to get the SPI clock. If we
* want a usable range of 4KHz to 25MHz for the SPI, then:
*
* 1. SPICLK must be greater than (8*25MHz) = 200MHz (so we can't reach 25MHz),
* and
* 2. SPICLK must be less than (254*40Khz) = 101.6MHz.
*
* If we assume that CCLK less than or equal to 100MHz, we can just
* use the CCLK undivided to get the SPI_CLOCK.
*/
#define SPI_PCLKSET_DIV SYSCON_PCLKSEL_CCLK
#define SPI_CLOCK LPC17_CCLK
/****************************************************************************
* Private Types
****************************************************************************/
/* This structure descibes the state of the SSP driver */
struct lpc17_spidev_s
{
struct spi_dev_s spidev; /* Externally visible part of the SPI interface */
#ifndef CONFIG_SPI_OWNBUS
sem_t exclsem; /* Held while chip is selected for mutual exclusion */
uint32_t frequency; /* Requested clock frequency */
uint32_t actual; /* Actual clock frequency */
uint8_t nbits; /* Width of word in bits (8 to 16) */
uint8_t mode; /* Mode 0,1,2,3 */
#endif
};
/****************************************************************************
* Private Function Prototypes
****************************************************************************/
/* SPI methods */
#ifndef CONFIG_SPI_OWNBUS
static int spi_lock(FAR struct spi_dev_s *dev, bool lock);
#endif
static uint32_t spi_setfrequency(FAR struct spi_dev_s *dev, uint32_t frequency);
static void spi_setmode(FAR struct spi_dev_s *dev, enum spi_mode_e mode);
static void spi_setbits(FAR struct spi_dev_s *dev, int nbits);
static uint16_t spi_send(FAR struct spi_dev_s *dev, uint16_t ch);
static void spi_sndblock(FAR struct spi_dev_s *dev, FAR const void *buffer, size_t nwords);
static void spi_recvblock(FAR struct spi_dev_s *dev, FAR void *buffer, size_t nwords);
/****************************************************************************
* Private Data
****************************************************************************/
static const struct spi_ops_s g_spiops =
{
#ifndef CONFIG_SPI_OWNBUS
.lock = spi_lock,
#endif
.select = lpc17_spiselect,
.setfrequency = spi_setfrequency,
.setmode = spi_setmode,
.setbits = spi_setbits,
.status = lpc17_spistatus,
#ifdef CONFIG_SPI_CMDDATA
.cmddata = lpc17_spicmddata,
#endif
.send = spi_send,
.sndblock = spi_sndblock,
.recvblock = spi_recvblock,
#ifdef CONFIG_SPI_CALLBACK
.registercallback = lpc17_spiregister, /* Provided externally */
#else
.registercallback = 0, /* Not implemented */
#endif
};
static struct lpc17_spidev_s g_spidev =
{
.spidev = { &g_spiops },
};
/****************************************************************************
* Public Data
****************************************************************************/
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Name: spi_lock
*
* Description:
* On SPI busses where there are multiple devices, it will be necessary to
* lock SPI to have exclusive access to the busses for a sequence of
* transfers. The bus should be locked before the chip is selected. After
* locking the SPI bus, the caller should then also call the setfrequency,
* setbits, and setmode methods to make sure that the SPI is properly
* configured for the device. If the SPI buss is being shared, then it
* may have been left in an incompatible state.
*
* Input Parameters:
* dev - Device-specific state data
* lock - true: Lock spi bus, false: unlock SPI bus
*
* Returned Value:
* None
*
****************************************************************************/
#ifndef CONFIG_SPI_OWNBUS
static int spi_lock(FAR struct spi_dev_s *dev, bool lock)
{
FAR struct lpc17_spidev_s *priv = (FAR struct lpc17_spidev_s *)dev;
if (lock)
{
/* Take the semaphore (perhaps waiting) */
while (sem_wait(&priv->exclsem) != 0)
{
/* The only case that an error should occur here is if the wait was awakened
* by a signal.
*/
ASSERT(errno == EINTR);
}
}
else
{
(void)sem_post(&priv->exclsem);
}
return OK;
}
#endif
/****************************************************************************
* Name: spi_setfrequency
*
* Description:
* Set the SPI frequency.
*
* Input Parameters:
* dev - Device-specific state data
* frequency - The SPI frequency requested
*
* Returned Value:
* Returns the actual frequency selected
*
****************************************************************************/
static uint32_t spi_setfrequency(FAR struct spi_dev_s *dev, uint32_t frequency)
{
FAR struct lpc17_spidev_s *priv = (FAR struct lpc17_spidev_s *)dev;
uint32_t divisor;
uint32_t actual;
/* Check if the requested frequence is the same as the frequency selection */
DEBUGASSERT(priv && frequency <= SPI_CLOCK / 2);
#ifndef CONFIG_SPI_OWNBUS
if (priv->frequency == frequency)
{
/* We are already at this frequency. Return the actual. */
return priv->actual;
}
#endif
/* frequency = SPI_CLOCK / divisor, or divisor = SPI_CLOCK / frequency */
divisor = SPI_CLOCK / frequency;
/* The SPI CCR register must contain an even number greater than or equal to 8. */
if (divisor < 8)
{
divisor = 8;
}
else if (divisor > 254)
{
divisor = 254;
}
divisor = (divisor + 1) & ~1;
/* Save the new divisor value */
putreg32(divisor, LPC17_SPI_CCR);
/* Calculate the new actual */
actual = SPI_CLOCK / divisor;
/* Save the frequency setting */
#ifndef CONFIG_SPI_OWNBUS
priv->frequency = frequency;
priv->actual = actual;
#endif
spidbg("Frequency %d->%d\n", frequency, actual);
return actual;
}
/****************************************************************************
* Name: spi_setmode
*
* Description:
* Set the SPI mode. Optional. See enum spi_mode_e for mode definitions
*
* Input Parameters:
* dev - Device-specific state data
* mode - The SPI mode requested
*
* Returned Value:
* none
*
****************************************************************************/
static void spi_setmode(FAR struct spi_dev_s *dev, enum spi_mode_e mode)
{
FAR struct lpc17_spidev_s *priv = (FAR struct lpc17_spidev_s *)dev;
uint32_t regval;
/* Has the mode changed? */
#ifndef CONFIG_SPI_OWNBUS
if (mode != priv->mode)
{
#endif
/* Yes... Set CR appropriately */
regval = getreg32(LPC17_SPI_CR);
regval &= ~(SPI_CR_CPOL|SPI_CR_CPHA);
switch (mode)
{
case SPIDEV_MODE0: /* CPOL=0; CPHA=0 */
break;
case SPIDEV_MODE1: /* CPOL=0; CPHA=1 */
regval |= SPI_CR_CPHA;
break;
case SPIDEV_MODE2: /* CPOL=1; CPHA=0 */
regval |= SPI_CR_CPOL;
break;
case SPIDEV_MODE3: /* CPOL=1; CPHA=1 */
regval |= (SPI_CR_CPOL|SPI_CR_CPHA);
break;
default:
DEBUGASSERT(FALSE);
return;
}
putreg32(regval, LPC17_SPI_CR);
/* Save the mode so that subsequent re-configuratins will be faster */
#ifndef CONFIG_SPI_OWNBUS
priv->mode = mode;
}
#endif
}
/****************************************************************************
* Name: spi_setbits
*
* Description:
* Set the number if bits per word.
*
* Input Parameters:
* dev - Device-specific state data
* nbits - The number of bits requests
*
* Returned Value:
* none
*
****************************************************************************/
static void spi_setbits(FAR struct spi_dev_s *dev, int nbits)
{
FAR struct lpc17_spidev_s *priv = (FAR struct lpc17_spidev_s *)dev;
uint32_t regval;
/* Has the number of bits changed? */
DEBUGASSERT(priv && nbits > 7 && nbits < 17);
#ifndef CONFIG_SPI_OWNBUS
if (nbits != priv->nbits)
{
#endif
/* Yes... Set CR appropriately */
regval = getreg32(LPC17_SPI_CR);
regval &= ~SPI_CR_BITS_MASK;
regval |= (nbits << SPI_CR_BITS_SHIFT) & SPI_CR_BITS_MASK;
regval |= SPI_CR_BITENABLE;
regval = getreg32(LPC17_SPI_CR);
/* Save the selection so the subsequence re-configurations will be faster */
#ifndef CONFIG_SPI_OWNBUS
priv->nbits = nbits;
}
#endif
}
/****************************************************************************
* Name: spi_send
*
* Description:
* Exchange one word on SPI
*
* Input Parameters:
* dev - Device-specific state data
* wd - The word to send. the size of the data is determined by the
* number of bits selected for the SPI interface.
*
* Returned Value:
* response
*
****************************************************************************/
static uint16_t spi_send(FAR struct spi_dev_s *dev, uint16_t wd)
{
/* Write the data to transmitted to the SPI Data Register */
putreg32((uint32_t)wd, LPC17_SPI_DR);
/* Wait for the SPIF bit in the SPI Status Register to be set to 1. The
* SPIF bit will be set after the last sampling clock edge of the SPI
* data transfer.
*/
while ((getreg32(LPC17_SPI_SR) & SPI_SR_SPIF) == 0);
/* Read the SPI Status Register again to clear the status bit */
(void)getreg32(LPC17_SPI_SR);
return (uint16_t)getreg32(LPC17_SPI_DR);
}
/*************************************************************************
* Name: spi_sndblock
*
* Description:
* Send a block of data on SPI
*
* Input Parameters:
* dev - Device-specific state data
* buffer - A pointer to the buffer of data to be sent
* nwords - the length of data to send from the buffer in number of words.
* The wordsize is determined by the number of bits-per-word
* selected for the SPI interface. If nbits <= 8, the data is
* packed into uint8_t's; if nbits >8, the data is packed into uint16_t's
*
* Returned Value:
* None
*
****************************************************************************/
static void spi_sndblock(FAR struct spi_dev_s *dev, FAR const void *buffer, size_t nwords)
{
FAR uint8_t *ptr = (FAR uint8_t*)buffer;
uint8_t data;
spidbg("nwords: %d\n", nwords);
while (nwords)
{
/* Write the data to transmitted to the SPI Data Register */
data = *ptr++;
putreg32((uint32_t)data, LPC17_SPI_DR);
/* Wait for the SPIF bit in the SPI Status Register to be set to 1. The
* SPIF bit will be set after the last sampling clock edge of the SPI
* data transfer.
*/
while ((getreg32(LPC17_SPI_SR) & SPI_SR_SPIF) == 0);
/* Read the SPI Status Register again to clear the status bit */
(void)getreg32(LPC17_SPI_SR);
nwords--;
}
}
/****************************************************************************
* Name: spi_recvblock
*
* Description:
* Revice a block of data from SPI
*
* Input Parameters:
* dev - Device-specific state data
* buffer - A pointer to the buffer in which to recieve data
* nwords - the length of data that can be received in the buffer in number
* of words. The wordsize is determined by the number of bits-per-word
* selected for the SPI interface. If nbits <= 8, the data is
* packed into uint8_t's; if nbits >8, the data is packed into uint16_t's
*
* Returned Value:
* None
*
****************************************************************************/
static void spi_recvblock(FAR struct spi_dev_s *dev, FAR void *buffer, size_t nwords)
{
FAR uint8_t *ptr = (FAR uint8_t*)buffer;
spidbg("nwords: %d\n", nwords);
while (nwords)
{
/* Write some dummy data to the SPI Data Register in order to clock the
* read data.
*/
putreg32(0xff, LPC17_SPI_DR);
/* Wait for the SPIF bit in the SPI Status Register to be set to 1. The
* SPIF bit will be set after the last sampling clock edge of the SPI
* data transfer.
*/
while ((getreg32(LPC17_SPI_SR) & SPI_SR_SPIF) == 0);
/* Read the SPI Status Register again to clear the status bit */
(void)getreg32(LPC17_SPI_SR);
/* Read the received data from the SPI Data Register */
*ptr++ = (uint8_t)getreg32(LPC17_SPI_DR);
nwords--;
}
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: lpc17_spiinitialize
*
* Description:
* Initialize the selected SPI port.
*
* Input Parameter:
* Port number (for hardware that has mutiple SPI interfaces)
*
* Returned Value:
* Valid SPI device structure reference on succcess; a NULL on failure
*
****************************************************************************/
FAR struct spi_dev_s *lpc17_spiinitialize(int port)
{
FAR struct lpc17_spidev_s *priv = &g_spidev;
irqstate_t flags;
uint32_t regval;
/* Configure multiplexed pins as connected on the board. Chip select
* pins must be configured by board-specific logic. All SPI pins and
* one SPI1 pin (SCK) have multiple, alternative pin selection.
* Definitions in the board.h file must be provided to resolve the
* board-specific pin configuration like:
*
* #define GPIO_SPI_SCK GPIO_SPI_SCK_1
*/
flags = irqsave();
lpc17_configgpio(GPIO_SPI_SCK);
lpc17_configgpio(GPIO_SPI_MISO);
lpc17_configgpio(GPIO_SPI_MOSI);
/* Configure clocking */
regval = getreg32(LPC17_SYSCON_PCLKSEL0);
regval &= ~SYSCON_PCLKSEL0_SPI_MASK;
regval |= (SPI_PCLKSET_DIV << SYSCON_PCLKSEL0_SPI_SHIFT);
putreg32(regval, LPC17_SYSCON_PCLKSEL0);
/* Enable peripheral clocking to SPI and SPI1 */
regval = getreg32(LPC17_SYSCON_PCONP);
regval |= SYSCON_PCONP_PCSPI;
putreg32(regval, LPC17_SYSCON_PCONP);
irqrestore(flags);
/* Configure 8-bit SPI mode and master mode */
putreg32(SPI_CR_BITS_8BITS|SPI_CR_BITENABLE|SPI_CR_MSTR, LPC17_SPI_CR);
/* Set the initial SPI configuration */
#ifndef CONFIG_SPI_OWNBUS
priv->frequency = 0;
priv->nbits = 8;
priv->mode = SPIDEV_MODE0;
#endif
/* Select a default frequency of approx. 400KHz */
spi_setfrequency((FAR struct spi_dev_s *)priv, 400000);
/* Initialize the SPI semaphore that enforces mutually exclusive access */
#ifndef CONFIG_SPI_OWNBUS
sem_init(&priv->exclsem, 0, 1);
#endif
return &priv->spidev;
}
#endif /* CONFIG_LPC17_SPI */