/****************************************************************************
* arch/arm/src/lpc43xx/lpc43_start.c
* arch/arm/src/chip/lpc43_start.c
*
* Copyright (C) 2012, 2015 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/*
* Power-Up Reset Overview
* -----------------------
*
* The ARM core starts executing code on reset with the program counter set
* to 0x0000:0000. The LPC43xx contains a shadow pointer register that
* allows areas of memory to be mapped to address 0x0000:0000. The default,
* reset value of the shadow pointer is 0x1040:0000 so that on reset code in
* the boot ROM is always executed first.
*
* The boot starts after reset is released. The IRC is selected as CPU clock
* and the Cortex-M4 starts the boot loader. By default the JTAG access to the
* chip is disabled at reset. The boot ROM determines the boot mode based on
* the OTP BOOT_SRC value or reset state pins. For flash-based parts, the part
* boots from internal flash by default. Otherwse, the boot ROM copies the
* image to internal SRAM at location 0x1000:0000, sets the ARM's shadow
* pointer to 0x1000:0000, and jumps to that location.
*
* However, using JTAG the executable image can be also loaded directly into
* and executed from SRAM.
*/
#include <nuttx/config.h>
#include <stdint.h>
#include <assert.h>
#include <debug.h>
#include <nuttx/init.h>
#include <arch/board/board.h>
#include "up_arch.h"
#include "up_internal.h"
#include "nvic.h"
#include "chip/lpc43_creg.h"
#include "lpc43_rgu.h"
#include "lpc43_cgu.h"
#include "lpc43_emc.h"
#include "lpc43_uart.h"
#include "lpc43_userspace.h"
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/****************************************************************************
* Name: showprogress
*
* Description:
* Print a character on the UART to show boot status.
*
****************************************************************************/
#ifdef CONFIG_DEBUG
# define showprogress(c) up_lowputc(c)
#else
# define showprogress(c)
#endif
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: lpc43_setbootrom
*
* Description:
* Set the shadow register to 0x1040:0000 and the VTOR to 0x0000:0000 so
* that any exceptions (particulary things like hard faults) that occur
* before we are initialized are caught by the BOOT ROM.
*
****************************************************************************/
static inline void lpc43_setbootrom(void)
{
/* Set the shadow register to the beginning of the boot ROM (Only bits 12-31) */
putreg32(LPC43_ROM_BASE, LPC43_CREG_M4MEMMAP);
/* Address zero now maps to the Boot ROM. Make sure that the VTOR will
* use the ROM vector table at that address.
*/
putreg32(0, NVIC_VECTAB);
}
/****************************************************************************
* Name: lpc43_enabuffering
*
* Description:
* If we are executing from external FLASH, then enable buffering.
*
****************************************************************************/
#if defined(CONFIG_LPC43_BOOT_CS0FLASH) || defined(CONFIG_LPC43_BOOT_CS1FLASH) || \
defined(CONFIG_LPC43_BOOT_CS2FLASH) || defined(CONFIG_LPC43_BOOT_CS3FLASH)
static inline void lpc43_enabuffering(void)
{
uint32_t regval;
#ifdef CONFIG_LPC43_BOOT_CS0FLASH
regval = getreg32(LPC43_EMC_STATCONFIG0);
regval |= EMC_STATCONFIG_BENA
putreg32(regval, LPC43_EMC_STATCONFIG0);
#endif
#ifdef CONFIG_LPC43_BOOT_CS1FLASH
regval = getreg32(LPC43_EMC_STATCONFIG1);
regval |= EMC_STATCONFIG_BENA
putreg32(regval, LPC43_EMC_STATCONFIG1);
#endif
#ifdef CONFIG_LPC43_BOOT_CS2FLASH
regval = getreg32(LPC43_EMC_STATCONFIG2);
regval |= EMC_STATCONFIG_BENA
putreg32(regval, LPC43_EMC_STATCONFIG2);
#endif
#ifdef CONFIG_LPC43_BOOT_CS3FLASH
regval = getreg32(LPC43_EMC_STATCONFIG3);
regval |= EMC_STATCONFIG_BENA
putreg32(regval, LPC43_EMC_STATCONFIG3);
#endif
}
#else
# define lpc43_enabuffering()
#endif
/****************************************************************************
* Name: lpc43_fpuconfig
*
* Description:
* Configure the FPU. Relative bit settings:
*
* CPACR: Enables access to CP10 and CP11
* CONTROL.FPCA: Determines whether the FP extension is active in the
* current context:
* FPCCR.ASPEN: Enables automatic FP state preservation, then the
* processor sets this bit to 1 on successful completion of any FP
* instruction.
* FPCCR.LSPEN: Enables lazy context save of FP state. When this is
* done, the processor reserves space on the stack for the FP state,
* but does not save that state information to the stack.
*
* Software must not change the value of the ASPEN bit or LSPEN bit while either:
* - the CPACR permits access to CP10 and CP11, that give access to the FP
* extension, or
* - the CONTROL.FPCA bit is set to 1
*
****************************************************************************/
#ifdef CONFIG_ARCH_FPU
#if defined(CONFIG_ARMV7M_CMNVECTOR) && !defined(CONFIG_ARMV7M_LAZYFPU)
static inline void lpc43_fpuconfig(void)
{
uint32_t regval;
/* Set CONTROL.FPCA so that we always get the extended context frame
* with the volatile FP registers stacked above the basic context.
*/
regval = getcontrol();
regval |= (1 << 2);
setcontrol(regval);
/* Ensure that FPCCR.LSPEN is disabled, so that we don't have to contend
* with the lazy FP context save behaviour. Clear FPCCR.ASPEN since we
* are going to turn on CONTROL.FPCA for all contexts.
*/
regval = getreg32(NVIC_FPCCR);
regval &= ~((1 << 31) | (1 << 30));
putreg32(regval, NVIC_FPCCR);
/* Enable full access to CP10 and CP11 */
regval = getreg32(NVIC_CPACR);
regval |= ((3 << (2*10)) | (3 << (2*11)));
putreg32(regval, NVIC_CPACR);
}
#else
static inline void lpc43_fpuconfig(void)
{
uint32_t regval;
/* Clear CONTROL.FPCA so that we do not get the extended context frame
* with the volatile FP registers stacked in the saved context.
*/
regval = getcontrol();
regval &= ~(1 << 2);
setcontrol(regval);
/* Ensure that FPCCR.LSPEN is disabled, so that we don't have to contend
* with the lazy FP context save behaviour. Clear FPCCR.ASPEN since we
* are going to keep CONTROL.FPCA off for all contexts.
*/
regval = getreg32(NVIC_FPCCR);
regval &= ~((1 << 31) | (1 << 30));
putreg32(regval, NVIC_FPCCR);
/* Enable full access to CP10 and CP11 */
regval = getreg32(NVIC_CPACR);
regval |= ((3 << (2*10)) | (3 << (2*11)));
putreg32(regval, NVIC_CPACR);
}
#endif
#else
# define lpc43_fpuconfig()
#endif
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: _start
*
* Description:
* This is the reset entry point.
*
****************************************************************************/
void __start(void)
{
const uint32_t *src;
uint32_t *dest;
/* Reset as many of the LPC43 peripherals as possible. This is necessary
* because the LPC43 does not provide any way of performing a full system
* reset under debugger control. So, if CONFIG_DEBUG is set (indicating
* that a debugger is being used?), the boot logic will call this
* function on all restarts.
*/
#ifdef CONFIG_DEBUG
lpc43_softreset();
#endif
/* Make sure that any exceptions (such as hard faults) that occur before
* we are initialized are caught by the BOOT ROM.
*/
lpc43_setbootrom();
/* Configure the CGU clocking and the console uart so that we can get
* debug output as soon as possible.
*/
lpc43_clockconfig();
lpc43_lowsetup();
showprogress('A');
/* If we are executing from external FLASH, then enable buffering */
lpc43_enabuffering();
/* Clear .bss. We'll do this inline (vs. calling memset) just to be
* certain that there are no issues with the state of global variables.
*/
for (dest = &_sbss; dest < &_ebss; )
{
*dest++ = 0;
}
showprogress('B');
/* Move the initialized data section from his temporary holding spot in
* FLASH into the correct place in SRAM. The correct place in SRAM is
* give by _sdata and _edata. The temporary location is in FLASH at the
* end of all of the other read-only data (.text, .rodata) at _eronly.
*/
for (src = &_eronly, dest = &_sdata; dest < &_edata; )
{
*dest++ = *src++;
}
showprogress('C');
/* Initialize the FPU (if configured) */
lpc43_fpuconfig();
showprogress('D');
/* Perform early serial initialization */
#ifdef USE_EARLYSERIALINIT
up_earlyserialinit();
#endif
showprogress('E');
/* For the case of the separate user-/kernel-space build, perform whatever
* platform specific initialization of the user memory is required.
* Normally this just means initializing the user space .data and .bss
* segments.
*/
#ifdef CONFIG_BUILD_PROTECTED
lpc43_userspace();
showprogress('F');
#endif
/* Initialize onboard resources */
lpc43_boardinitialize();
showprogress('G');
/* Then start NuttX */
showprogress('\r');
showprogress('\n');
os_start();
/* Shouldn't get here */
for (;;);
}