|
|
/************************************************************************************
* arch/mips/src/pic32mz/pic32mz-gpio.h
*
* Copyright (C) 2015 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __ARCH_MIPS_SRC_PIC32MZ_PIC32MZ_GPIO_H
#define __ARCH_MIPS_SRC_PIC32MZ_PIC32MZ_GPIO_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <nuttx/irq.h>
#include <arch/pic32mz/irq.h>
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* GPIO settings used in the configport, readport, writeport, etc.
*
* General encoding:
* MMAV IIDR RRRx PPPP
*/
#define GPIO_MODE_SHIFT (14) /* Bits 14-15: I/O mode */
#define GPIO_MODE_MASK (3 << GPIO_MODE_SHIFT)
# define GPIO_INPUT (0 << GPIO_MODE_SHIFT) /* 00 Normal input */
# define GPIO_OUTPUT (2 << GPIO_MODE_SHIFT) /* 10 Normal output */
# define GPIO_OPENDRAN (3 << GPIO_MODE_SHIFT) /* 11 Open drain output */
#define GPIO_ANALOG_MASK (1 << 13) /* Bit 13: Analog */
# define GPIO_ANALOG (1 << 13)
# define GPIO_DIGITAL (0)
#define GPIO_VALUE_MASK (1 << 12) /* Bit 12: Initial output value */
# define GPIO_VALUE_ONE (1 << 12)
# define GPIO_VALUE_ZERO (0)
#define GPIO_INTERRUPT (1 << 11) /* Bit 11: Change notification enable */
#define GPIO_PULLUP (1 << 10) /* Bit 10: Change notification pull-up */
#define GPIO_PULLDOWN (1 << 9) /* Bit 9: Change notification pull-down */
#define GPIO_PORT_SHIFT (5) /* Bits 5-8: Port number */
#define GPIO_PORT_MASK (15 << GPIO_PORT_SHIFT)
# define GPIO_PORTA (0 << GPIO_PORT_SHIFT)
# define GPIO_PORTB (1 << GPIO_PORT_SHIFT)
# define GPIO_PORTC (2 << GPIO_PORT_SHIFT)
# define GPIO_PORTD (3 << GPIO_PORT_SHIFT)
# define GPIO_PORTE (4 << GPIO_PORT_SHIFT)
# define GPIO_PORTF (5 << GPIO_PORT_SHIFT)
# define GPIO_PORTG (6 << GPIO_PORT_SHIFT)
# define GPIO_PORTH (7 << GPIO_PORT_SHIFT)
# define GPIO_PORTJ (8 << GPIO_PORT_SHIFT)
# define GPIO_PORTK (9 << GPIO_PORT_SHIFT)
#define GPIO_PIN_SHIFT 0 /* Bits 0-3: GPIO number: 0-15 */
#define GPIO_PIN_MASK (15 << GPIO_PIN_SHIFT)
#define GPIO_PIN0 (0 << GPIO_PIN_SHIFT)
#define GPIO_PIN1 (1 << GPIO_PIN_SHIFT)
#define GPIO_PIN2 (2 << GPIO_PIN_SHIFT)
#define GPIO_PIN3 (3 << GPIO_PIN_SHIFT)
#define GPIO_PIN4 (4 << GPIO_PIN_SHIFT)
#define GPIO_PIN5 (5 << GPIO_PIN_SHIFT)
#define GPIO_PIN6 (6 << GPIO_PIN_SHIFT)
#define GPIO_PIN7 (7 << GPIO_PIN_SHIFT)
#define GPIO_PIN8 (8 << GPIO_PIN_SHIFT)
#define GPIO_PIN9 (9 << GPIO_PIN_SHIFT)
#define GPIO_PIN10 (10 << GPIO_PIN_SHIFT)
#define GPIO_PIN11 (11 << GPIO_PIN_SHIFT)
#define GPIO_PIN12 (12 << GPIO_PIN_SHIFT)
#define GPIO_PIN13 (13 << GPIO_PIN_SHIFT)
#define GPIO_PIN14 (14 << GPIO_PIN_SHIFT)
#define GPIO_PIN15 (15 << GPIO_PIN_SHIFT)
/************************************************************************************
* Public Types
************************************************************************************/
#ifndef __ASSEMBLY__
typedef uint16_t pinset_t;
/************************************************************************************
* Public Data
************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
/* This table can be used to map a port number to a IOPORT base address. For
* example, an index of zero would correspond to IOPORTA, one with IOPORTB,
* etc.
*/
EXTERN const uintptr_t g_gpiobase[CHIP_NPORTS];
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: pic32mz_configgpio
*
* Description:
* Configure a GPIO pin based on bit-encoded description of the pin (the interrupt
* will be configured when pic32mz_attach() is called).
*
* Returned Value:
* OK on success; negated errno on failure.
*
************************************************************************************/
int pic32mz_configgpio(pinset_t cfgset);
/************************************************************************************
* Name: pic32mz_gpiowrite
*
* Description:
* Write one or zero to the selected GPIO pin
*
************************************************************************************/
void pic32mz_gpiowrite(pinset_t pinset, bool value);
/************************************************************************************
* Name: pic32mz_gpioread
*
* Description:
* Read one or zero from the selected GPIO pin
*
************************************************************************************/
bool pic32mz_gpioread(pinset_t pinset);
/************************************************************************************
* Name: pic32mz_gpioirqinitialize
*
* Description:
* Initialize logic to support a GPIO change notification interrupts. This
* function is called internally by the system on power up and should not be
* called again.
*
************************************************************************************/
#ifdef CONFIG_PIC32MZ_GPIOIRQ
void pic32mz_gpioirqinitialize(void);
#else
# define pic32mz_gpioirqinitialize()
#endif
/************************************************************************************
* Name: pic32mz_gpioattach
*
* Description:
* Attach an interrupt service routine to a GPIO interrupt. This will also
* reconfigure the pin as an interrupting input. The change notification number is
* associated with all interrupt-capable GPIO pins. The association could,
* however, differ from part to part and must be provided by the caller.
*
* When an interrupt occurs, it is due to a change on the GPIO input pin. In that
* case, all attached handlers will be called. Each handler must maintain state
* and determine if the underlying GPIO input value changed.
*
* Parameters:
* - pinset: GPIO pin configuration
* - cn: The change notification number associated with the pin
* - handler: Interrupt handler (may be NULL to detach)
*
* Returns:
* The previous value of the interrupt handler function pointer. This value may,
* for example, be used to restore the previous handler when multiple handlers are
* used.
*
************************************************************************************/
#ifdef CONFIG_PIC32MZ_GPIOIRQ
xcpt_t pic32mz_gpioattach(pinset_t pinset, xcpt_t handler);
#else
# define pic32mz_gpioattach(p,f) (NULL)
#endif
/************************************************************************************
* Name: pic32mz_gpioirqenable
*
* Description:
* Enable the interrupt for specified GPIO IRQ
*
************************************************************************************/
#ifdef CONFIG_PIC32MZ_GPIOIRQ
void pic32mz_gpioirqenable(pinset_t pinset);
#else
# define pic32mz_gpioirqenable(irq)
#endif
/************************************************************************************
* Name: pic32mz_gpioirqdisable
*
* Description:
* Disable the interrupt for specified GPIO IRQ
*
************************************************************************************/
#ifdef CONFIG_PIC32MZ_GPIOIRQ
void pic32mz_gpioirqdisable(pinset_t pinset);
#else
# define pic32mz_gpioirqdisable(irq)
#endif
/************************************************************************************
* Function: pic32mz_dumpgpio
*
* Description:
* Dump all GPIO registers associated with the provided base address
*
************************************************************************************/
#ifdef CONFIG_DEBUG_GPIO
void pic32mz_dumpgpio(uint32_t pinset, const char *msg);
#else
# define pic32mz_dumpgpio(p,m)
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_MIPS_SRC_PIC32MZ_PIC32MZ_GPIO_H */
|