/****************************************************************************
* configs/sam4l-xplained/src/sam_userleds.c
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/* There are three LEDs on board the SAM4L Xplained Pro board: The EDBG
* controls two of the LEDs, a power LED and a status LED. There is only
* one user controllable LED, a yellow LED labeled LED0 near the SAM4L USB
* connector.
*
* This LED is controlled by PC07 and LED0 can be activated by driving the
* PC07 to GND.
*
* When CONFIG_ARCH_LEDS is defined in the NuttX configuration, NuttX will
* control LED0. Otherwise, LED0 can be controlled from user applications
* using the logic in this file.
*/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <stdbool.h>
#include <debug.h>
#include <arch/board/board.h>
#include "sam_gpio.h"
#include "sam4l-xplained.h"
#ifndef CONFIG_ARCH_LEDS
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* CONFIG_DEBUG_LEDS enables debug output from this file (needs CONFIG_DEBUG
* with CONFIG_DEBUG_VERBOSE too)
*/
#ifdef CONFIG_DEBUG_LEDS
# define leddbg lldbg
# define ledvdbg llvdbg
#else
# define leddbg(x...)
# define ledvdbg(x...)
#endif
/****************************************************************************
* Private Data
****************************************************************************/
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: sam_ledinit
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board
* LEDs. If CONFIG_ARCH_LEDS is not defined, then the sam_ledinit() is
* available to initialize the LED0 from user application logic.
*
****************************************************************************/
void sam_ledinit(void)
{
(void)sam_configgpio(GPIO_LED0);
}
/****************************************************************************
* Name: sam_setled
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board
* LEDs. If CONFIG_ARCH_LEDS is not defined, then the sam_setled() is
* available to control the LED0 from user application logic.
*
*****************************************************************************/
void sam_setled(int led, bool ledon)
{
if (led == BOARD_LED0)
{
sam_gpiowrite(GPIO_LED0, !ledon);
}
}
/****************************************************************************
* Name: sam_setled
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board
* LEDs. If CONFIG_ARCH_LEDS is not defined, then the sam_setleds() is
* available to control the LED0 from user application logic. NOTE: since
* there is only a single LED on-board, this is function is not very useful.
*
*****************************************************************************/
void sam_setleds(uint8_t ledset)
{
sam_setled(BOARD_LED0, (ledset & BOARD_LED0_BIT) != 0);
}
#endif /* !CONFIG_ARCH_LEDS */
