|
|
/************************************************************************************
* configs/sama5d3x-ek/src/sama5d3x-ek.h
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_SAMA5D3X_EK_SRC_SAMA5D3X_EK_H
#define __CONFIGS_SAMA5D3X_EK_SRC_SAMA5D3X_EK_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
#include <arch/irq.h>
#include <nuttx/irq.h>
#include "chip/sam_pinmap.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* LEDs *****************************************************************************/
/* There are two LEDs on the SAMA5D3 series-CM board that can be controlled
* by software. A blue LED is controlled via GPIO pins. A red LED normally
* provides an indication that power is supplied to the board but can also
* be controlled via software.
*
* PE25. This blue LED is pulled high and is illuminated by pulling PE25
* low.
*
* PE24. The red LED is also pulled high but is driven by a transistor so
* that it is illuminated when power is applied even if PE24 is not
* configured as an output. If PE24 is configured as an output, then the
* LCD is illuminated by a high output.
*/
#define GPIO_BLUE (GPIO_OUTPUT | GPIO_CFG_PULLUP | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOE | GPIO_PIN25)
#define GPIO_RED (GPIO_OUTPUT | GPIO_CFG_PULLUP | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOE | GPIO_PIN24)
/* Buttons **************************************************************************/
/* There are five push button switches on the SAMA5D3X-EK base board:
*
* 1. One Reset, board reset (BP1)
* 2. One Wake up, push button to bring the processor out of low power mode
* (BP2)
* 3. One User momentary Push Button
* 4. One Disable CS Push Button
*
* Only the momentary push button is controllable by software (labeled
* "PB_USER1" on the board):
*
* - PE27. Pressing the switch connect PE27 to grounded. Therefore, PE27
* must be pulled high internally. When the button is pressed the SAMA5
* will sense "0" is on PE27.
*/
#define GPIO_USER1 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \
GPIO_INT_BOTHEDGES | GPIO_PORT_PIOE | GPIO_PIN27)
#define IRQ_USER1 SAM_IRQ_PE27
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Public data
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Functions
************************************************************************************/
/************************************************************************************
* Name: board_sdram_config
*
* Description:
* Configures DDR2 (MT47H128M16RT 128MB or, optionally, MT47H64M16HR)
*
* Per the SAMA5D3x-EK User guide: "Two SDRAM/DDR2 used as main system memory.
* MT47H128M16 - 2 Gb - 16 Meg x 16 x 8 banks, the board provides up to 2 Gb on-
* board, soldered DDR2 SDRAM. The memory bus is 32 bits wide and operates with
* up to 166 MHz."
*
* From the Atmel Code Example:
* MT47H64M16HR : 8 Meg x 16 x 8 banks
* Refresh count: 8K
* Row address: A[12:0] (8K)
* Column address A[9:0] (1K)
* Bank address BA[2:0] a(24,25) (8)
*
* This logic was taken from Atmel sample code for the SAMA5D3x-EK.
*
* Input Parameters:
* devtype - Either DDRAM_MT47H128M16RT or DDRAM_MT47H64M16HR
*
* Assumptions:
* The DDR memory regions is configured as strongly ordered memory. When we
* complete initialization of SDRAM and it is ready for use, we will make DRAM
* into normal memory.
*
************************************************************************************/
#if defined(CONFIG_SAMA5_DDRCS) && !defined(CONFIG_SAMA5_BOOT_SDRAM)
void sam_sdram_config(void);
#else
# define board_sdram_config(t)
#endif
/************************************************************************************
* Name: up_ledinit
************************************************************************************/
#ifdef CONFIG_ARCH_LEDS
void up_ledinit(void);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_SAMA5D3X_EK_SRC_SAMA5D3X_EK_H */
|
