/****************************************************************************
* configs/z80sim/src/z80_serial.c
*
* Copyright (C) 2007-2009, 2012 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include <unistd.h>
#include <string.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/irq.h>
#include <nuttx/arch.h>
#include <nuttx/serial/serial.h>
#include <arch/serial.h>
#include "up_arch.h"
#include "os_internal.h"
#include "up_internal.h"
#ifdef USE_SERIALDRIVER
/****************************************************************************
* Definitions
****************************************************************************/
/****************************************************************************
* Private Types
****************************************************************************/
/****************************************************************************
* Private Function Prototypes
****************************************************************************/
static int up_setup(FAR struct uart_dev_s *dev);
static void up_shutdown(FAR struct uart_dev_s *dev);
static int up_attach(FAR struct uart_dev_s *dev);
static void up_detach(FAR struct uart_dev_s *dev);
static int up_ioctl(FAR struct file *filep, int cmd, unsigned long arg);
static int up_receive(FAR struct uart_dev_s *dev, unsigned int *status);
static void up_rxint(FAR struct uart_dev_s *dev, bool enable);
static bool up_rxavailable(FAR struct uart_dev_s *dev);
static void up_send(FAR struct uart_dev_s *dev, int ch);
static void up_txint(FAR struct uart_dev_s *dev, bool enable);
static bool up_txready(FAR struct uart_dev_s *dev);
static bool up_txempty(FAR struct uart_dev_s *dev);
/****************************************************************************
* Private Variables
****************************************************************************/
static const struct uart_ops_s g_uart_ops =
{
up_setup, /* setup */
up_shutdown, /* shutdown */
up_attach, /* attach */
up_detach, /* detach */
up_ioctl, /* ioctl */
up_receive, /* receive */
up_rxint, /* rxint */
up_rxavailable, /* rxavailable */
up_send, /* send */
up_txint, /* txint */
up_txready, /* txready */
up_txempty, /* txempty */
};
/* I/O buffers */
static char g_uartrxbuffer[CONFIG_UART_RXBUFSIZE];
static char g_uarttxbuffer[CONFIG_UART_TXBUFSIZE];
/* This describes the state of the fake UART port. */
static uart_dev_t g_uartport =
{
0, /* open_count */
false, /* xmitwaiting */
false, /* recvwaiting */
true, /* isconsole */
{ 1 }, /* closesem */
{ 0 }, /* xmitsem */
{ 0 }, /* recvsem */
{ /* xmit */
{ 1 }, /* sem */
0, /* head */
0, /* tail */
CONFIG_UART_TXBUFSIZE, /* size */
g_uarttxbuffer, /* buffer */
},
{ /* recv */
{ 1 }, /* sem */
0, /* head */
0, /* tail */
CONFIG_UART_RXBUFSIZE, /* size */
g_uartrxbuffer, /* buffer */
},
&g_uart_ops, /* ops */
NULL, /* priv */
};
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Name: up_setup
*
* Description:
* Configure the UART baud, bits, parity, fifos, etc. This
* method is called the first time that the serial port is
* opened.
*
****************************************************************************/
static int up_setup(FAR struct uart_dev_s *dev)
{
return OK;
}
/****************************************************************************
* Name: up_shutdown
*
* Description:
* Disable the UART. This method is called when the serial
* port is closed
*
****************************************************************************/
static void up_shutdown(FAR struct uart_dev_s *dev)
{
}
/****************************************************************************
* Name: up_attach
*
* Description:
* Configure the UART to operation in interrupt driven mode. This method is
* called when the serial port is opened. Normally, this is just after the
* setup() method is called, however, the serial console may operate in a
* non-interrupt driven mode during the boot phase.
*
* RX and TX interrupts are not enabled by the attach method (unless the
* hardware supports multiple levels of interrupt enabling). The RX and TX
* interrupts are not enabled until the txint() and rxint() methods are called.
*
****************************************************************************/
static int up_attach(FAR struct uart_dev_s *dev)
{
return OK;
}
/****************************************************************************
* Name: up_detach
*
* Description:
* Detach UART interrupts. This method is called when the serial port is
* closed normally just before the shutdown method is called. The exception is
* the serial console which is never shutdown.
*
****************************************************************************/
static void up_detach(FAR struct uart_dev_s *dev)
{
}
/****************************************************************************
* Name: up_ioctl
*
* Description:
* All ioctl calls will be routed through this method
*
****************************************************************************/
static int up_ioctl(FAR struct file *filep, int cmd, unsigned long arg)
{
*get_errno_ptr() = ENOTTY;
return ERROR;
}
/****************************************************************************
* Name: up_receive
*
* Description:
* Called (usually) from the interrupt level to receive one
* character from the UART. Error bits associated with the
* receipt are provided in the return 'status'.
*
****************************************************************************/
static int up_receive(FAR struct uart_dev_s *dev, unsigned int *status)
{
uint8_t ch = z80_lowgetc();
*status = 0;
return ch;
}
/****************************************************************************
* Name: up_rxint
*
* Description:
* Call to enable or disable RX interrupts
*
****************************************************************************/
static void up_rxint(FAR struct uart_dev_s *dev, bool enable)
{
}
/****************************************************************************
* Name: up_rxavailable
*
* Description:
* Return true if the receive fifo is not empty
*
****************************************************************************/
static bool up_rxavailable(FAR struct uart_dev_s *dev)
{
return true;
}
/****************************************************************************
* Name: up_send
*
* Description:
* This method will send one byte on the UART
*
****************************************************************************/
static void up_send(FAR struct uart_dev_s *dev, int ch)
{
z80_lowputc(ch);
}
/****************************************************************************
* Name: up_txint
*
* Description:
* Call to enable or disable TX interrupts
*
****************************************************************************/
static void up_txint(FAR struct uart_dev_s *dev, bool enable)
{
}
/****************************************************************************
* Name: up_txready
*
* Description:
* Return true if the tranmsit fifo is not full
*
****************************************************************************/
static bool up_txready(FAR struct uart_dev_s *dev)
{
return true;
}
/****************************************************************************
* Name: up_txempty
*
* Description:
* Return true if the transmit fifo is empty
*
****************************************************************************/
static bool up_txempty(FAR struct uart_dev_s *dev)
{
return true;
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: up_serialinit
*
* Description:
* Performs the low level UART initialization early in
* debug so that the serial console will be available
* during bootup. This must be called before up_serialinit.
*
****************************************************************************/
void up_earlyserialinit(void)
{
}
/****************************************************************************
* Name: up_serialinit
*
* Description:
* Register serial console and serial ports. This assumes
* that up_earlyserialinit was called previously.
*
****************************************************************************/
void up_serialinit(void)
{
(void)uart_register("/dev/console", &g_uartport);
(void)uart_register("/dev/ttyS0", &g_uartport);
}
#endif /* USE_SERIALDRIVER */
/****************************************************************************
* Name: up_putc
*
* Description:
* Provide priority, low-level access to support OS debug
* writes
*
****************************************************************************/
int up_putc(int ch)
{
z80_lowputc(ch);
return 0;
}