/****************************************************************************
* drivers/net/cs89x0.h
*
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#ifndef __DRIVERS_NET_CS89x0_H
#define __DRIVERS_NET_CS89x0_H
/****************************************************************************
* Included Files
****************************************************************************/
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* CONFIG_CS89x0_ALIGN16/32 determines if the 16-bit CS89x0 registers are
* aligned to 16-bit or 32-bit address boundaries. NOTE: If there multiple
* CS89x00 parts in the board architecture, we assume that the address
* alignment is the same for all implementations. If that is not the
* case, then it will be necessary to move a shift value into
* the cs89x0_driver_s structure and calculate the offsets dynamically in
* the putreg and getreg functions.
*/
#if defined(CONFIG_CS89x0_ALIGN16)
# define CS89x0_RTDATA_OFFSET (0 << 1)
# define CS89x0_TxCMD_OFFSET (2 << 1)
# define CS89x0_TxLEN_OFFSET (3 << 1)
# define CS89x0_ISQ_OFFSET (4 << 1)
# define CS89x0_PPTR_OFFSET (5 << 1)
# define CS89x0_PDATA_OFFSET (6 << 1)
#elif defined(CONFIG_CS89x0_ALIGN32)
# define CS89x0_RTDATA_OFFSET (0 << 2)
# define CS89x0_TxCMD_OFFSET (2 << 2)
# define CS89x0_TxLEN_OFFSET (3 << 2)
# define CS89x0_ISQ_OFFSET (4 << 2)
# define CS89x0_PPTR_OFFSET (5 << 2)
# define CS89x0_PDATA_OFFSET (6 << 2)
#else
# error "CS89x00 address alignment is not defined"
#endif
/* ISQ register bit definitions */
#define ISQ_EVENTMASK 0x003f /* Bits 0-5 indicate the status register */
#define ISQ_RXEVENT 0x0004
#define ISQ_TXEVENT 0x0008
#define ISQ_BUFEVENT 0x000c
#define ISQ_RXMISSEVENT 0x0010
#define ISQ_TXCOLEVENT 0x0012
/* ISQ register TxEVENT bit definitions*/
#define ISQ_RXEVENT_IAHASH (1 << 6)
#define ISQ_RXEVENT_DRIBBLE (1 << 7)
#define ISQ_RXEVENT_RXOK (1 << 8)
#define ISQ_RXEVENT_HASHED (1 << 9)
#define ISQ_RXEVENT_HASHNDX_SHIFT 10
#define ISQ_RXEVENT_HASHNDX_MASK (0x3f << ISQ_RXEVENT_HASHNDX_SHIFT)
/* ISQ register TxEVENT bit definitions*/
#define ISQ_TXEVENT_LOSSOFCRS (1 << 6)
#define ISQ_TXEVENT_SQEERROR (1 << 7)
#define ISQ_TXEVENT_TXOK (1 << 8)
#define ISQ_TXEVENT_OUTWINDOW (1 << 9)
#define ISQ_TXEVENT_JABBER (1 << 10)
#define ISQ_TXEVENT_NCOLLISION_SHIFT 11
#define ISQ_TXEVENT_NCOLLISION_MASK (15 << ISQ_TXEVENT_NCOLLISION_SHIFT)
#define ISQ_TXEVENT_16COLL (1 << 15)
/* ISQ register BufEVENT bit definitions */
#define ISQ_BUFEVENT_SWINT (1 << 6)
#define ISQ_BUFEVENT_RXDMAFRAME (1 << 7)
#define ISQ_BUFEVENT_RDY4TX (1 << 8)
#define ISQ_BUFEVENT_TXUNDERRUN (1 << 9)
#define ISQ_BUFEVENT_RXMISS (1 << 10)
#define ISQ_BUFEVENT_RX128 (1 << 11)
#define ISQ_BUFEVENT_RXDEST (1 << 15)
/* Packet page register offsets *********************************************/
/* 0x0000 Bus interface registers */
#define PPR_CHIPID 0x0000 /* Chip identifier - must be 0x630E */
#define PPR_CHIPREV 0x0002 /* Chip revision, model codes */
#define PPR_IOBASEADDRESS 0x0020 /* I/O Base Address */
#define PPR_INTREG 0x0022 /* Interrupt configuration */
# define PPR_INTREG_IRQ0 0x0000 /* Use INTR0 pin */
# define PPR_INTREG_IRQ1 0x0001 /* Use INTR1 pin */
# define PPR_INTREG_IRQ2 0x0002 /* Use INTR2 pin */
# define PPR_INTREG_IRQ3 0x0003 /* Use INTR3 pin */
#define PPR_DMACHANNELNUMBER 0x0024 /* DMA Channel Number (0,1, or 2) */
#define PPR_DMASTARTOFFRAME 0x0026 /* DMA Start of Frame */
#define PPR_DMAFRAMECOUNT 0x0028 /* DMA Frame Count (12-bits) */
#define PPR_RXDMABYTECOUNT 0x002a /* Rx DMA Byte Count */
#define PPR_MEMORYBASEADDRESS 0x002c /* Memory Base Address Register (20-bit) */
#define PPR_BOOTPROMBASEADDRESS 0x0030 /* Boot PROM Base Address */
#define PPR_BOOTPROMADDRESSMASK 0x0034 /* Boot PROM Address Mask */
#define PPR_EEPROMCOMMAND 0x0040 /* EEPROM Command */
#define PPR_EEPROMDATA 0x0042 /* EEPROM Data */
#define PPR_RECVFRAMEBYTES 0x0050 /* Received Frame Byte Counter */
/* 0x0100 - Configuration and control registers */
#define PPR_RXCFG 0x0102 /* Receiver configuration */
# define PPR_RXCFG_SKIP1 (1 << 6) /* Skip (discard) current frame */
# define PPR_RXCFG_STREAM (1 << 7) /* Enable streaming mode */
# define PPR_RXCFG_RXOK (1 << 8) /* RxOK interrupt enable */
# define PPR_RxCFG_RxDMAonly (1 << 9) /* Use RxDMA for all frames */
# define PPR_RxCFG_AutoRxDMA (1 << 10) /* Select RxDMA automatically */
# define PPR_RxCFG_BufferCRC (1 << 11) /* Include CRC characters in frame */
# define PPR_RxCFG_CRC (1 << 12) /* Enable interrupt on CRC error */
# define PPR_RxCFG_RUNT (1 << 13) /* Enable interrupt on RUNT frames */
# define PPR_RxCFG_EXTRA (1 << 14) /* Enable interrupt on frames with extra data */
#define PPR_RXCTL 0x0104 /* Receiver control */
# define PPR_RXCTL_IAHASH (1 << 6) /* Accept frames that match hash */
# define PPR_RXCTL_PROMISCUOUS (1 << 7) /* Accept any frame */
# define PPR_RXCTL_RXOK (1 << 8) /* Accept well formed frames */
# define PPR_RXCTL_MULTICAST (1 << 9) /* Accept multicast frames */
# define PPR_RXCTL_IA (1 << 10) /* Accept frame that matches IA */
# define PPR_RXCTL_BROADCAST (1 << 11) /* Accept broadcast frames */
# define PPR_RXCTL_CRC (1 << 12) /* Accept frames with bad CRC */
# define PPR_RXCTL_RUNT (1 << 13) /* Accept runt frames */
# define PPR_RXCTL_EXTRA (1 << 14) /* Accept frames that are too long */
#define PPR_TXCFG 0x0106 /* Transmit configuration */
# define PPR_TXCFG_CRS (1 << 6) /* Enable interrupt on loss of carrier */
# define PPR_TXCFG_SQE (1 << 7) /* Enable interrupt on Signal Quality Error */
# define PPR_TXCFG_TXOK (1 << 8) /* Enable interrupt on successful xmits */
# define PPR_TXCFG_LATE (1 << 9) /* Enable interrupt on "out of window" */
# define PPR_TXCFG_JABBER (1 << 10) /* Enable interrupt on jabber detect */
# define PPR_TXCFG_COLLISION (1 << 11) /* Enable interrupt if collision */
# define PPR_TXCFG_16COLLISIONS (1 << 15) /* Enable interrupt if > 16 collisions */
#define PPR_TXCMD 0x0108 /* Transmit command status */
# define PPR_TXCMD_TXSTART5 (0 << 6) /* Start after 5 bytes in buffer */
# define PPR_TXCMD_TXSTART381 (1 << 6) /* Start after 381 bytes in buffer */
# define PPR_TXCMD_TXSTART1021 (2 << 6) /* Start after 1021 bytes in buffer */
# define PPR_TXCMD_TXSTARTFULL (3 << 6) /* Start after all bytes loaded */
# define PPR_TXCMD_FORCE (1 << 8) /* Discard any pending packets */
# define PPR_TXCMD_ONECOLLISION (1 << 9) /* Abort after a single collision */
# define PPR_TXCMD_NOCRC (1 << 12) /* Do not add CRC */
# define PPR_TXCMD_NOPAD (1 << 13) /* Do not pad short packets */
#define PPR_BUFCFG 0x010a /* Buffer configuration */
# define PPR_BUFCFG_SWI (1 << 6) /* Force interrupt via software */
# define PPR_BUFCFG_RXDMA (1 << 7) /* Enable interrupt on Rx DMA */
# define PPR_BUFCFG_TXRDY (1 << 8) /* Enable interrupt when ready for Tx */
# define PPR_BUFCFG_TXUE (1 << 9) /* Enable interrupt in Tx underrun */
# define PPR_BUFCFG_RXMISS (1 << 10) /* Enable interrupt on missed Rx packets */
# define PPR_BUFCFG_RX128 (1 << 11) /* Enable Rx interrupt after 128 bytes */
# define PPR_BUFCFG_TXCOL (1 << 12) /* Enable int on Tx collision ctr overflow */
# define PPR_BUFCFG_MISS (1 << 13) /* Enable int on Rx miss ctr overflow */
# define PPR_BUFCFG_RXDEST (1 << 15) /* Enable int on Rx dest addr match */
#define PPR_LINECTL 0x0112 /* Line control */
# define PPR_LINECTL_RX (1 << 6) /* Enable receiver */
# define PPR_LINECTL_TX (1 << 7) /* Enable transmitter */
# define PPR_LINECTL_AUIONLY (1 << 8) /* AUI interface only */
# define PPR_LINECTL_AUTOAUI10BT (1 << 9) /* Autodetect AUI or 10BaseT interface */
# define PPR_LINECTL_MODBACKOFFE (1 << 11) /* Enable modified backoff algorithm */
# define PPR_LINECTL_POLARITYDIS (1 << 12) /* Disable Rx polarity autodetect */
# define PPR_LINECTL_2PARTDEFDIS (1 << 13) /* Disable two-part defferal */
# define PPR_LINECTL_LORXSQUELCH (1 << 14) /* Reduce receiver squelch threshold */
#define PPR_SELFCTL 0x0114 /* Chip self control */
# define PPR_SELFCTL_RESET (1 << 6) /* Self-clearing reset */
# define PPR_SELFCTL_SWSUSPEND (1 << 8) /* Initiate suspend mode */
# define PPR_SELFCTL_HWSLEEPE (1 << 9) /* Enable SLEEP input */
# define PPR_SELFCTL_HWSTANDBYE (1 << 10) /* Enable standby mode */
# define PPR_SELFCTL_HC0E (1 << 12) /* Use HCB0 for LINK LED */
# define PPR_SELFCTL_HC1E (1 << 13) /* Use HCB1 for BSTATUS LED */
# define PPR_SELFCTL_HCB0 (1 << 14) /* Control LINK LED if HC0E set */
# define PPR_SELFCTL_HCB1 (1 << 15) /* Cntrol BSTATUS LED if HC1E set */
#define PPR_BUSCTL 0x0116 /* Bus control */
# define PPR_BUSCTL_RESETRXDMA (1 << 6) /* Reset RxDMA pointer */
# define PPR_BUSCTL_DMAEXTEND (1 << 8) /* Extend DMA cycle */
# define PPR_BUSCTL_USESA (1 << 9) /* Assert MEMCS16 on address decode */
# define PPR_BUSCTL_MEMORYE (1 << 10) /* Enable memory mode */
# define PPR_BUSCTL_DMABURST (1 << 11) /* Limit DMA access burst */
# define PPR_BUSCTL_IOCHRDYE (1 << 12) /* Set IOCHRDY high impedence */
# define PPR_BUSCTL_RXDMASIZE (1 << 13) /* Set DMA buffer size 64KB */
# define PPR_BUSCTL_ENABLEIRQ (1 << 15) /* Generate interrupt on interrupt event */
#define PPR_TESTCTL 0x0118 /* Test control */
# define PPR_TESTCTL_DISABLELT (1 << 7) /* Disable link status */
# define PPR_TESTCTL_ENDECLOOP (1 << 9) /* Internal loopback */
# define PPR_TESTCTL_AUILOOP (1 << 10) /* AUI loopback */
# define PPR_TESTCTL_DISBACKOFF (1 << 11) /* Disable backoff algorithm */
# define PPR_TESTCTL_FDX (1 << 14) /* Enable full duplex mode */
/* 0x0120 - Status and Event Registers */
#define PPR_ISQ 0x0120 /* Interrupt Status Queue */
#define PPR_RER 0x0124 /* Receive event */
# define PPR_RER_IAHASH (1 << 6) /* Frame hash match */
# define PPR_RER_DRIBBLE (1 << 7) /* Frame had 1-7 extra bits after last byte */
# define PPR_RER_RXOK (1 << 8) /* Frame received with no errors */
# define PPR_RER_HASHED (1 << 9) /* Frame address hashed OK */
# define PPR_RER_IA (1 << 10) /* Frame address matched IA */
# define PPR_RER_BROADCAST (1 << 11) /* Broadcast frame */
# define PPR_RER_CRC (1 << 12) /* Frame had CRC error */
# define PPR_RER_RUNT (1 << 13) /* Runt frame */
# define PPR_RER_EXTRA (1 << 14) /* Frame was too long */
#define PPR_TER 0x0128 /* Transmit event */
# define PPR_TER_CRS (1 << 6) /* Carrier lost */
# define PPR_TER_SQE (1 << 7) /* Signal Quality Error */
# define PPR_TER_TXOK (1 << 8) /* Packet sent without error */
# define PPR_TER_LATE (1 << 9) /* Out of window */
# define PPR_TER_JABBER (1 << 10) /* Stuck transmit? */
# define PPR_TER_NUMCOLLISIONS_SHIFT 11
# define PPR_TER_NUMCOLLISIONS_MASK (15 << PPR_TER_NUMCOLLISIONS_SHIFT)
# define PPR_TER_16COLLISIONS (1 << 15) /* > 16 collisions */
#define PPR_BER 0x012C /* Buffer event */
# define PPR_BER_SWINT (1 << 6) /* Software interrupt */
# define PPR_BER_RXDMAFRAME (1 << 7) /* Received framed DMAed */
# define PPR_BER_RDY4TX (1 << 8) /* Ready for transmission */
# define PPR_BER_TXUNDERRUN (1 << 9) /* Transmit underrun */
# define PPR_BER_RXMISS (1 << 10) /* Received frame missed */
# define PPR_BER_RX128 (1 << 11) /* 128 bytes received */
# define PPR_BER_RXDEST (1 << 15) /* Received framed passed address filter */
#define PPR_RXMISS 0x0130 /* Receiver miss counter */
#define PPR_TXCOL 0x0132 /* Transmit collision counter */
#define PPR_LINESTAT 0x0134 /* Line status */
# define PPR_LINESTAT_LINKOK (1 << 7) /* Line is connected and working */
# define PPR_LINESTAT_AUI (1 << 8) /* Connected via AUI */
# define PPR_LINESTAT_10BT (1 << 9) /* Connected via twisted pair */
# define PPR_LINESTAT_POLARITY (1 << 12) /* Line polarity OK (10BT only) */
# define PPR_LINESTAT_CRS (1 << 14) /* Frame being received */
#define PPR_SELFSTAT 0x0136 /* Chip self status */
# define PPR_SELFSTAT_33VACTIVE (1 << 6) /* supply voltage is 3.3V */
# define PPR_SELFSTAT_INITD (1 << 7) /* Chip initialization complete */
# define PPR_SELFSTAT_SIBSY (1 << 8) /* EEPROM is busy */
# define PPR_SELFSTAT_EEPROM (1 << 9) /* EEPROM present */
# define PPR_SELFSTAT_EEPROMOK (1 << 10) /* EEPROM checks out */
# define PPR_SELFSTAT_ELPRESENT (1 << 11) /* External address latch logic available */
# define PPR_SELFSTAT_EESIZE (1 << 12) /* Size of EEPROM */
#define PPR_BUSSTAT 0x0138 /* Bus status */
# define PPR_BUSSTAT_TXBID (1 << 7) /* Tx error */
# define PPR_BUSSTAT_TXRDY (1 << 8) /* Ready for Tx data */
#define PPR_TDR 0x013C /* AUI Time Domain Reflectometer */
/* 0x0144 - Initiate transmit registers */
#define PPR_TXCOMMAND 0x0144 /* Tx Command */
#define PPR_TXLENGTH 0x0146 /* Tx Length */
/* 0x0150 - Address filter registers */
#define PPR_LAF 0x0150 /* Logical address filter (6 bytes) */
#define PPR_IA 0x0158 /* Individual address (MAC) */
/* 0x0400 - Frame location registers */
#define PPR_RXSTATUS 0x0400 /* Rx Status */
#define PPR_RXLENGTH 0x0402 /* Rx Length */
#define PPR_RXFRAMELOCATION 0x0404 /* Rx Frame Location */
#define PPR_TXFRAMELOCATION 0x0a00 /* Tx Frame Location */
/****************************************************************************
* Public Types
****************************************************************************/
/****************************************************************************
* Public Data
****************************************************************************/
#ifdef __cplusplus
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
#undef EXTERN
#ifdef __cplusplus
}
#endif
#endif /* __DRIVERS_NET_CS89x0_H */