USB config options

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@971 42af7a65-404d-4744-a932-0658087f49c3

1 files changed, 50 insertions, 0 deletions

diff --git a/nuttx/configs/ntosd-dm320/README.txt b/nuttx/configs/ntosd-dm320/README.txt
index c569a51cc..03111148b 100644
--- a/nuttx/configs/ntosd-dm320/README.txt
+++ b/nuttx/configs/ntosd-dm320/README.txt
@@ -13,27 +13,77 @@ Where <subdir> is one of the following:
 
 ostest
 ^^^^^^
+
 This configuration directory, performs a simple OS test using
 examples/ostest.
 
 nsh
 ^^^
+
 Configures the NuttShell (nsh) located at examples/nsh.  The
 Configuration enables both the serial and telnetd NSH interfaces.
 
 nettest
 ^^^^^^^
+
 This alternative configuration directory may be used to
 enable networking using the OSDs DM9000A Ethernet interface.
 It uses examples/nettest to excercise the TCP/IP network.
 
 uip
 ^^^
+
 This configuration file demonstrates the tiny webserver
 at examples/uip.
 
 udp
 ^^^
+
 This alternative configuration directory is similar to nettest
 except that is use examples/upd to exercise UDP.
 
+Configuration Options
+^^^^^^^^^^^^^^^^^^^^^
+
+In additional to the common configuration options listed in the
+file configs/README.txt, there are other configuration options
+specific to the DM320:
+
+ CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+   processor architecture.
+ CONFIG_ARCH_name - for use in C code.  This identifies the
+   particular chip or SoC that the architecture is implemented
+   in.
+ CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+ CONFIG_ARCH_CHIP_name - For use in C code
+ CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+   the board that supports the particular chip or SoC.
+ CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+ CONFIG_ARCH_BOARD_name - for use in C code
+ CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+ CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to lpc2148.
+ CONFIG_DRAM_SIZE - Describes the internal DRAM.
+ CONFIG_DRAM_START - The start address of internal DRAM
+ CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+
+DM320 specific device driver settings
+
+ CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
+   console and ttys0 (default is the UART0).
+ CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
+   This specific the size of the receive buffer
+ CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
+   being sent.  This specific the size of the transmit buffer
+ CONFIG_UARTn_BAUD - The configure BAUD of the UART.  Must be
+ CONFIG_UARTn_BITS - The number of bits.  Must be either 7 or 8.
+ CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+ CONFIG_UARTn_2STOP - Two stop bits
+
+DM320 USB Configuration
+
+ CONFIG_DM320_GIO_USBATTACH
+   GIO that detects USB attach/detach events
+ CONFIG_DM320_GIO_USBDPPULLUP
+   GIO connected to D+.  Support software connect/disconnect.
+ CONFIG_DMA320_USBDEV_DMA
+   Enable DM320-specific DMA support