SAMA5: Add logic to control VBUS power for OHCI

4 files changed, 372 insertions, 53 deletions

diff --git a/nuttx/configs/sama5d3x-ek/README.txt b/nuttx/configs/sama5d3x-ek/README.txt
index 5998bcc04..04b42212e 100644
--- a/nuttx/configs/sama5d3x-ek/README.txt
+++ b/nuttx/configs/sama5d3x-ek/README.txt
@@ -75,6 +75,7 @@ Contents
   - Serial Consoles
   - Serial FLASH
   - HSMCI Card Slots
+  - USB Ports
   - SAMA5D3x-EK Configuration Options
   - Configurations
 
@@ -564,6 +565,59 @@ HSMCI Card Slots
     PB24  MCI1_CK
     PB19  MCI1_CDA
 
+USB Ports
+=========
+
+  The SAMA5D3 series-MB features three USB communication ports:
+
+    * Port A Host High Speed (EHCI) and Full Speed (OHCI) multiplexed with
+      USB Device High Speed Micro AB connector, J20
+
+    * Port B Host High Speed (EHCI) and Full Speed (OHCI) standard type A
+      connector, J19 upper port
+
+    * Port C Host Full Speed (OHCI) only standard type A connector, J19
+      lower port
+
+  All three USB host ports are equipped with 500 mA high-side power switch
+  for self-powered and buspowered applications. The USB device port feature
+  VBUS inserts detection function.
+
+  Port A
+  ------
+
+    PIO  Signal Name Function
+    ---- ----------- -------------------------------------------------------
+    PD29  VBUS_SENSE VBus detection
+    PD25  EN5V_USBA  VBus power enable (via MN15 AIC1526 Dual USB High-Side
+                     Power Switch.  The other channel of the switch is for
+                     the LCD)
+
+  Port B
+  ------
+
+    PIO  Signal Name Function
+    ---- ----------- -------------------------------------------------------
+    PD26 EN5V_USBB   VBus power enable (via MN14 AIC1526 Dual USB High-Side
+                     Power Switch).  To the A1 pin of J19 Dual USB A
+                     connector
+
+  Port C
+  ------
+
+    PIO  Signal Name Function
+    ---- ----------- -------------------------------------------------------
+    PD27 EN5V_USBC   VBus power enable (via MN14 AIC1526 Dual USB High-Side
+                     Power Switch).  To the B1 pin of J19 Dual USB A
+                     connector
+
+  Both Ports B and C
+  ------------------
+
+    PIO  Signal Name Function
+    ---- ----------- -------------------------------------------------------
+    PD28 OVCUR_USB   Combined overrcurrent indication from port A and B
+
 SAMA5D3x-EK Configuration Options
 =================================
 
@@ -1131,6 +1185,9 @@ Configurations
         Library Routines
           CONFIG_SCHED_WORKQUEUE               : Worker thread support is required
 
+       Application Configuration -> NSH Library
+         CONFIG_NSH_ARCHINIT=y                 : NSH board-initialization
+
     STATUS:
       2013-7-19:  This configuration (as do the others) run at 396MHz.
         The SAMA5D3 can run at 536MHz.  I still need to figure out the
diff --git a/nuttx/configs/sama5d3x-ek/src/sam_nsh.c b/nuttx/configs/sama5d3x-ek/src/sam_nsh.c
index 1b7ecea4e..648a015a6 100644
--- a/nuttx/configs/sama5d3x-ek/src/sam_nsh.c
+++ b/nuttx/configs/sama5d3x-ek/src/sam_nsh.c
@@ -88,6 +88,22 @@
 #  define AT25_MINOR CONFIG_NSH_MMCSDMINOR
 #endif
 
+/* Debug ********************************************************************/
+
+#ifdef CONFIG_CPP_HAVE_VARARGS
+#  ifdef CONFIG_DEBUG
+#    define message(...) syslog(__VA_ARGS__)
+#  else
+#    define message(...) printf(__VA_ARGS__)
+#  endif
+#else
+#  ifdef CONFIG_DEBUG
+#    define message syslog
+#  else
+#    define message printf
+#  endif
+#endif
+
 /****************************************************************************
  * Public Functions
  ****************************************************************************/
@@ -102,7 +118,7 @@
 
 int nsh_archinitialize(void)
 {
-#if defined(HAVE_AT25_MTD) || defined(HAVE_HSMCI_MTD)
+#if defined(HAVE_AT25_MTD) || defined(HAVE_HSMCI_MTD) || defined(HAVE_USBHOST)
   int ret;
 #endif
 
@@ -112,7 +128,7 @@ int nsh_archinitialize(void)
   ret = sam_at25_initialize(AT25_MINOR);
   if (ret < 0)
     {
-      dbg("ERROR: sam_at25_initialize failed: %d\n", ret);
+      message("ERROR: sam_at25_initialize failed: %d\n", ret);
       return ret;
     }
 #endif
@@ -122,8 +138,8 @@ int nsh_archinitialize(void)
   ret = sam_hsmci_initialize(HSMCI0_SLOTNO, HSMCI0_MINOR);
   if (ret < 0)
     {
-      dbg("ERROR: sam_hsmci_initialize(%d,%d) failed: %d\n",
-          HSMCI0_SLOTNO, HSMCI0_MINOR, ret);
+      message("ERROR: sam_hsmci_initialize(%d,%d) failed: %d\n",
+              HSMCI0_SLOTNO, HSMCI0_MINOR, ret);
       return ret;
     }
 #endif
@@ -132,14 +148,14 @@ int nsh_archinitialize(void)
   ret = sam_hsmci_initialize(HSMCI1_SLOTNO, HSMCI1_MINOR);
   if (ret < 0)
     {
-      dbg("ERROR: sam_hsmci_initialize(%d,%d) failed: %d\n",
-          HSMCI1_SLOTNO, HSMCI1_MINOR, ret);
+      message("ERROR: sam_hsmci_initialize(%d,%d) failed: %d\n",
+              HSMCI1_SLOTNO, HSMCI1_MINOR, ret);
       return ret;
     }
 #endif
 #endif
 
-#if defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI)
+#ifdef HAVE_USBHOST
   /* Initialize USB host operation.  sam_usbhost_initialize() starts a thread
    * will monitor for USB connection and disconnection events.
    */
@@ -147,7 +163,7 @@ int nsh_archinitialize(void)
   ret = sam_usbhost_initialize();
   if (ret != OK)
     {
-      dbg("ERROR: Failed to initialize USB host: %d\n", ret);
+      message("ERROR: Failed to initialize USB host: %d\n", ret);
       return ret;
     }
 #endif
diff --git a/nuttx/configs/sama5d3x-ek/src/sam_usb.c b/nuttx/configs/sama5d3x-ek/src/sam_usb.c
index 98f989b75..3b009bb41 100644
--- a/nuttx/configs/sama5d3x-ek/src/sam_usb.c
+++ b/nuttx/configs/sama5d3x-ek/src/sam_usb.c
@@ -1,5 +1,5 @@
 /************************************************************************************
- * configs/sama5d3x-ek/src/up_usbdev.c
+ * configs/sama5d3x-ek/src/up_usb.c
  *
  *   Copyright (C) 2013 Gregory Nutt. All rights reserved.
  *   Author: Gregory Nutt <gnutt@nuttx.org>
@@ -52,7 +52,8 @@
 #include <nuttx/usb/usbdev_trace.h>
 
 #include "up_arch.h"
-#include "sam_ohci.h"
+#include "sam_pio.h"
+#include "sam_usbhost.h"
 #include "sama5d3x-ek.h"
 
 #if defined(CONFIG_SAMA5_UHPHS) || defined(CONFIG_SAMA5_UDPHS)
@@ -72,9 +73,13 @@
 /************************************************************************************
  * Private Data
  ************************************************************************************/
+/* Retained device driver handles */
 
-#if defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI)
-static struct usbhost_driver_s *g_drvr;
+#ifdef CONFIG_SAMA5_OHCI
+static struct usbhost_driver_s *g_ohci;
+#endif
+#ifdef CONFIG_SAMA5_EHCI
+static struct usbhost_driver_s *g_ehci;
 #endif
 
 /************************************************************************************
@@ -85,12 +90,12 @@ static struct usbhost_driver_s *g_drvr;
  * Name: usbhost_waiter
  *
  * Description:
- *   Wait for USB devices to be connected.
+ *   Wait for USB devices to be connected to either the OHCI or EHCI hub.
  *
  ************************************************************************************/
 
-#ifdef CONFIG_USBHOST
-static int usbhost_waiter(int argc, char *argv[])
+#if HAVE_USBHOST
+static int usbhost_waiter(struct usbhost_driver_s *dev)
 {
   bool connected = false;
 
@@ -99,7 +104,7 @@ static int usbhost_waiter(int argc, char *argv[])
     {
       /* Wait for the device to change state */
 
-      DEBUGVERIFY(DRVR_WAIT(g_drvr, connected) == OK);
+      DEBUGVERIFY(DRVR_WAIT(dev, connected) == OK);
 
       connected = !connected;
       uvdbg("%s\n", connected ? "connected" : "disconnected");
@@ -110,7 +115,7 @@ static int usbhost_waiter(int argc, char *argv[])
         {
           /* Yes.. enumerate the newly connected device */
 
-          (void)DRVR_ENUMERATE(g_drvr);
+          (void)DRVR_ENUMERATE(dev);
         }
     }
 
@@ -121,6 +126,36 @@ static int usbhost_waiter(int argc, char *argv[])
 #endif
 
 /************************************************************************************
+ * Name: ohci_waiter
+ *
+ * Description:
+ *   Wait for USB devices to be connected to the OHCI hub.
+ *
+ ************************************************************************************/
+
+#ifdef CONFIG_SAMA5_OHCI
+static int ohci_waiter(int argc, char *argv[])
+{
+  return usbhost_waiter(g_ohci);
+}
+#endif
+
+/************************************************************************************
+ * Name: ehci_waiter
+ *
+ * Description:
+ *   Wait for USB devices to be connected to the EHCI hub.
+ *
+ ************************************************************************************/
+
+#ifdef CONFIG_SAMA5_EHCI
+static int ehci_waiter(int argc, char *argv[])
+{
+  return usbhost_waiter(g_ehci);
+}
+#endif
+
+/************************************************************************************
  * Public Functions
  ************************************************************************************/
 
@@ -129,15 +164,93 @@ static int usbhost_waiter(int argc, char *argv[])
  *
  * Description:
  *   Called from sam_usbinitialize very early in inialization to setup USB-related
- *   GPIO pins for the STM32F4Discovery board.
+ *   GPIO pins for the SAMA5D3x-EK board.
+ *
+ * USB Ports
+ *   The SAMA5D3 series-MB features three USB communication ports:
+ *
+ *     1. Port A Host High Speed (EHCI) and Full Speed (OHCI) multiplexed with
+ *        USB Device High Speed Micro AB connector, J20
+ *
+ *     2. Port B Host High Speed (EHCI) and Full Speed (OHCI) standard type A
+ *        connector, J19 upper port
+ *
+ *     3. Port C Host Full Speed (OHCI) only standard type A connector, J19
+ *        lower port
+ *
+ *   All three USB host ports are equipped with 500 mA high-side power switch
+ *   for self-powered and buspowered applications. The USB device port feature
+ *   VBUS inserts detection function.
+ *
+ *   Port A
+ *
+ *     PIO  Signal Name Function
+ *     ---- ----------- -------------------------------------------------------
+ *     PD29  VBUS_SENSE VBus detection
+ *     PD25  EN5V_USBA  VBus power enable (via MN15 AIC1526 Dual USB High-Side
+ *                      Power Switch.  The other channel of the switch is for
+ *                      the LCD)
+ *
+ *   Port B
+ *
+ *     PIO  Signal Name Function
+ *     ---- ----------- -------------------------------------------------------
+ *     PD26 EN5V_USBB   VBus power enable (via MN14 AIC1526 Dual USB High-Side
+ *                      Power Switch).  To the A1 pin of J19 Dual USB A
+ *                      connector
+ *
+ *   Port C
+ *
+ *     PIO  Signal Name Function
+ *     ---- ----------- -------------------------------------------------------
+ *     PD27 EN5V_USBC   VBus power enable (via MN14 AIC1526 Dual USB High-Side
+ *                      Power Switch).  To the B1 pin of J19 Dual USB A
+ *                      connector
+ *
+ *    Both Ports B and C
+ *
+ *     PIO  Signal Name Function
+ *     ---- ----------- -------------------------------------------------------
+ *     PD28 OVCUR_USB   Combined overrcurrent indication from port A and B
+ *
+ * That offers a lot of flexibility.  However, here we enable the ports only
+ * as follows:
+ *
+ *   Port A -- USB device
+ *   Port B -- EHCI host
+ *   Port C -- OHCI host
  *
  ************************************************************************************/
 
 void weak_function sam_usbinitialize(void)
 {
-  /* Configure pull-ups */
+#if 0
+  /* Configure Port A to support the USB device function */
+
+  sam_configpio(PIO_USBA_VBUS_SENSE); /* VBUS sense */
+
+  /* TODO:  Configure an interrupt on VBUS sense */
+#endif
+
+#ifdef CONFIG_SAMA5_OHCI
+  /* Configure Port C to support the USB OHCI function */
+
+  sam_configpio(PIO_USBC_VBUS_ENABLE); /* VBUS enable, initially OFF */
+
+#endif
 
-  /* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent PIOs */
+#ifdef CONFIG_SAMA5_EHCI
+  /* Configure Port B to support the USB OHCI function */
+
+  sam_configpio(PIO_USBB_VBUS_ENABLE); /* VBUS enable, initially OFF */
+
+#endif
+
+#if defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI)
+  /* Configure Port B/C VBUS overrcurrent detection */
+
+  sam_configpio(PIO_USBBC_VBUS_OVERCURRENT); /* VBUS overcurrent */
+#endif
 }
 
 /***********************************************************************************
@@ -150,7 +263,7 @@ void weak_function sam_usbinitialize(void)
  *
  ***********************************************************************************/
 
-#if defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI)
+#if HAVE_USBHOST
 int sam_usbhost_initialize(void)
 {
   int pid;
@@ -160,30 +273,55 @@ int sam_usbhost_initialize(void)
    * that we care about:
    */
 
-  uvdbg("Register class drivers\n");
   ret = usbhost_storageinit();
   if (ret != OK)
     {
-      udbg("Failed to register the mass storage class\n");
+      udbg("ERROR: Failed to register the mass storage class: %d\n", ret);
+    }
+
+#ifdef CONFIG_SAMA5_OHCI
+  /* Get an instance of the USB OHCI interface */
+
+  g_ohci = sam_ohci_initialize(0);
+  if (!g_ohci)
+    {
+      udbg("ERROR: sam_ohci_initialize failed\n");
+      return -ENODEV;
     }
 
-  /* Then get an instance of the USB host interface */
+  /* Start a thread to handle device connection. */
 
-  uvdbg("Initialize USB host\n");
-  g_drvr = sam_ohci_initialize(0);
-  if (g_drvr)
+  pid = TASK_CREATE("usbhost", CONFIG_USBHOST_DEFPRIO,  CONFIG_USBHOST_STACKSIZE,
+                    (main_t)ohci_waiter, (FAR char * const *)NULL);
+  if (pid < 0)
     {
-      /* Start a thread to handle device connection. */
+      udbg("ERROR: Failed to create ohci_waiter task: %d\n", ret);
+      return -ENODEV;
+    }
+#endif
 
-      uvdbg("Start usbhost_waiter\n");
+#ifdef CONFIG_SAMA5_EHCI
+  /* Get an instance of the USB EHCI interface */
 
-      pid = TASK_CREATE("usbhost", CONFIG_USBHOST_DEFPRIO,
-                        CONFIG_USBHOST_STACKSIZE,
-                        (main_t)usbhost_waiter, (FAR char * const *)NULL);
-      return pid < 0 ? -ENOEXEC : OK;
+  g_ehci = sam_ehci_initialize(0);
+  if (!g_ehci)
+    {
+      udbg("ERROR: sam_ehci_initialize failed\n");
+      return -ENODEV;
     }
 
-  return -ENODEV;
+  /* Start a thread to handle device connection. */
+
+  pid = TASK_CREATE("usbhost", CONFIG_USBHOST_DEFPRIO,  CONFIG_USBHOST_STACKSIZE,
+                    (main_t)ehci_waiter, (FAR char * const *)NULL);
+  if (pid < 0)
+    {
+      udbg("ERROR: Failed to create ehci_waiter task: %d\n", ret);
+      return -ENODEV;
+    }
+#endif
+
+  return OK;
 }
 #endif
 
@@ -191,21 +329,13 @@ int sam_usbhost_initialize(void)
  * Name: sam_usbhost_vbusdrive
  *
  * Description:
- *   Enable/disable driving of VBUS 5V output.  This function must be provided be
- *   each platform that implements the STM32 OTG FS host interface
- *
- *   "On-chip 5 V VBUS generation is not supported. For this reason, a charge pump 
- *    or, if 5 V are available on the application board, a basic power switch, must 
- *    be added externally to drive the 5 V VBUS line. The external charge pump can 
- *    be driven by any GPIO output. When the application decides to power on VBUS 
- *    using the chosen GPIO, it must also set the port power bit in the host port 
- *    control and status register (PPWR bit in OTG_FS_HPRT).
- *
- *   "The application uses this field to control power to this port, and the core 
- *    clears this bit on an overcurrent condition."
+ *   Enable/disable driving of VBUS 5V output.  This function must be provided by
+ *   each platform that implements the OHCI or EHCI host interface
  *
  * Input Parameters:
- *   iface - For future growth to handle multiple USB host interface.  Should be zero.
+ *   iface  - Selects USB host interface:
+ *            0 = EHCI (Port B)
+ *            1 = OHCI (Port C)
  *   enable - true: enable VBUS power; false: disable VBUS power
  *
  * Returned Value:
@@ -213,18 +343,49 @@ int sam_usbhost_initialize(void)
  *
  ***********************************************************************************/
 
-#if defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI)
+#if HAVE_USBHOST
 void sam_usbhost_vbusdrive(int iface, bool enable)
 {
-  DEBUGASSERT(iface == 0);
-  
+  pio_pinset_t pinset;
+
+  /* Pick the PIO associated with the OHCI or EHCI interface */
+
+#ifdef CONFIG_SAMA5_OHCI
+  if (iface == SAM_OHCI_IFACE)
+    {
+      uvdbg("OHCI: iface %d enable %d\n", iface, enable);
+      pinset = PIO_USBC_VBUS_ENABLE;
+    }
+  else
+#endif
+
+#ifdef CONFIG_SAMA5_EHCI
+  if (iface == SAM_EHCI_IFACE)
+    {
+      uvdbg("EHCI: iface %d enable %d\n", iface, enable);
+      pinset = PIO_USBB_VBUS_ENABLE;
+    }
+  else
+#endif
+
+   {
+     udbg("ERROR: Unsupported iface %d\n", iface);
+     return;
+   }
+
+  /* Then enable or disable VBUS power */
+
   if (enable)
     {
       /* Enable the Power Switch by driving the enable pin low */
+
+        sam_piowrite(pinset, false);
     }
   else
-    { 
+    {
       /* Disable the Power Switch by driving the enable pin high */
+
+        sam_piowrite(pinset, false);
     }
 }
 #endif
@@ -244,9 +405,14 @@ void sam_usbhost_vbusdrive(int iface, bool enable)
  *
  ************************************************************************************/
 
-#if defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI)
+#if HAVE_USBHOST
 xcpt_t sam_setup_overcurrent(xcpt_t handler)
 {
+  /* Since this is a common signal, we will need to come up with some way to inform
+   * both EHCI and OHCI drivers when this error occurs.
+   */
+
+# warning Missing logic
   return NULL;
 }
 #endif
diff --git a/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h b/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h
index 76bd78808..0cf87b2e4 100644
--- a/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h
+++ b/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h
@@ -57,6 +57,7 @@
 
 #define HAVE_HSMCI_MTD  1
 #define HAVE_AT25_MTD   1
+#define HAVE_USBHOST    1
 
 /* HSMCI */
 /* Can't support MMC/SD if the card interface(s) are not enable */
@@ -141,6 +142,10 @@
 #  undef CONFIG_SAMA5_EHCI
 #endif
 
+#if !defined(CONFIG_SAMA5_OHCI) && !defined(CONFIG_SAMA5_EHCI)
+#  undef HAVE_USBHOST
+#endif
+
 /* LEDs *****************************************************************************/
 /* There are two LEDs on the SAMA5D3 series-CM board that can be controlled
  * by software.  A  blue LED is controlled via PIO pins.  A red LED normally
@@ -225,6 +230,81 @@
                       PIO_INT_BOTHEDGES | PIO_PORT_PIOD | PIO_PIN18)
 #define IRQ_MCI1_CD   SAM_IRQ_PD18
 
+/* USB Ports ************************************************************************/
+/* The SAMA5D3 series-MB features three USB communication ports:
+ *
+ *   1. Port A Host High Speed (EHCI) and Full Speed (OHCI) multiplexed with
+ *      USB Device High Speed Micro AB connector, J20
+ *
+ *   2. Port B Host High Speed (EHCI) and Full Speed (OHCI) standard type A
+ *      connector, J19 upper port
+ *
+ *   3. Port C Host Full Speed (OHCI) only standard type A connector, J19
+ *      lower port
+ *
+ * All three USB host ports are equipped with 500 mA high-side power switch
+ * for self-powered and buspowered applications. The USB device port feature
+ * VBUS inserts detection function.
+ *
+ * Port A
+ *
+ *   PIO  Signal Name Function
+ *   ---- ----------- -------------------------------------------------------
+ *   PD29  VBUS_SENSE VBus detection
+ *   PD25  EN5V_USBA  VBus power enable (via MN15 AIC1526 Dual USB High-Side
+ *                    Power Switch.  The other channel of the switch is for
+ *                    the LCD)
+ */
+
+#define PIO_USBA_VBUS_SENSE \
+                     (PIO_INPUT | PIO_CFG_PULLUP | PIO_CFG_DEGLITCH | \
+                      PIO_INT_BOTHEDGES | PIO_PORT_PIOD | PIO_PIN29)
+#define IRQ_USBA_VBUS_SENSE \
+                     SAM_IRQ_PD29
+
+#define PIO_USBA_VBUS_ENABLE \
+                     (PIO_OUTPUT | PIO_CFG_DEFAULT | PIO_OUTPUT_CLEAR | \
+                      PIO_PORT_PIOD | PIO_PIN25)
+
+/* Port B
+ *
+ *   PIO  Signal Name Function
+ *   ---- ----------- -------------------------------------------------------
+ *   PD26 EN5V_USBB   VBus power enable (via MN14 AIC1526 Dual USB High-Side
+ *                    Power Switch).  To the A1 pin of J19 Dual USB A
+ *                    connector
+ */
+
+#define PIO_USBB_VBUS_ENABLE \
+                     (PIO_OUTPUT | PIO_CFG_DEFAULT | PIO_OUTPUT_CLEAR | \
+                      PIO_PORT_PIOD | PIO_PIN26)
+
+/* Port C
+ *
+ *   PIO  Signal Name Function
+ *   ---- ----------- -------------------------------------------------------
+ *   PD27 EN5V_USBC   VBus power enable (via MN14 AIC1526 Dual USB High-Side
+ *                    Power Switch).  To the B1 pin of J19 Dual USB A
+ *                    connector
+ */
+
+#define PIO_USBC_VBUS_ENABLE \
+                     (PIO_OUTPUT | PIO_CFG_DEFAULT | PIO_OUTPUT_CLEAR | \
+                      PIO_PORT_PIOD | PIO_PIN27)
+
+/*  Both Ports B and C
+ *  
+ *   PIO  Signal Name Function
+ *   ---- ----------- -------------------------------------------------------
+ *   PD28 OVCUR_USB   Combined overrcurrent indication from port A and B
+ */
+
+#define PIO_USBBC_VBUS_OVERCURRENT \
+                     (PIO_INPUT | PIO_CFG_PULLUP | PIO_CFG_DEGLITCH | \
+                      PIO_INT_BOTHEDGES | PIO_PORT_PIOD | PIO_PIN28)
+#define IRQ_USBBC_VBUS_OVERCURRENT \
+                     SAM_IRQ_PD28
+
 /* SPI Chip Selects *****************************************************************/
 /* Both the Ronetix and Embest versions of the SAMAD3x CPU modules include an
  * Atmel AT25DF321A, 32-megabit, 2.7-volt SPI serial flash.  The SPI
@@ -379,7 +459,7 @@ void weak_function sam_usbinitialize(void);
  *
  ****************************************************************************************************/
 
-#if defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI)
+#ifdef HAVE_USBHOST
 int sam_usbhost_initialize(void);
 #endif