diff options
Diffstat (limited to 'nuttx/arch/arm/src/imx/imx_uart.h')
-rw-r--r-- | nuttx/arch/arm/src/imx/imx_uart.h | 219 |
1 files changed, 219 insertions, 0 deletions
diff --git a/nuttx/arch/arm/src/imx/imx_uart.h b/nuttx/arch/arm/src/imx/imx_uart.h new file mode 100644 index 000000000..d050e5ee7 --- /dev/null +++ b/nuttx/arch/arm/src/imx/imx_uart.h @@ -0,0 +1,219 @@ +/************************************************************************************ + * arch/arm/src/imx/imx_uart.h + * + * Copyright (C) 2009 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt <spudmonkey@racsa.co.cr> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ************************************************************************************/ + +#ifndef __ARCH_ARM_IMX_UART_H +#define __ARCH_ARM_IMX_UART_H + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +/************************************************************************************ + * Definitions + ************************************************************************************/ + +/* UART Register Offsets ************************************************************/ + +#define UART_RXD0 0x0000 /* UART receiver register 0 */ +#define UART_RXD1 0x0004 /* UART receiver register 1 */ +#define UART_RXD2 0x0008 /* UART receiver register 2 */ +#define UART_RXD3 0x000c /* UART receiver register 3 */ +#define UART_TXD0 0x0040 /* UART receiver register 0 */ +#define UART_TXD1 0x0044 /* UART receiver register 1 */ +#define UART_TXD2 0x0048 /* UART receiver register 2 */ +#define UART_TXD3 0x004c /* UART receiver register 3 */ +#define UART_UCR1 0x0080 /* UART control register 1 */ +#define UART_UCR2 0x0084 /* UART control register 2 */ +#define UART_UCR3 0x0088 /* UART control register 3 */ +#define UART_UCR4 0x008c /* UART control register 4 */ +#define UART_UFCR 0x0090 /* UART FIFO control register */ +#define UART_USR1 0x0094 /* UART status register 1 */ +#define UART_USR2 0x0098 /* UART status register 2 */ +#define UART_UESC 0x009c /* UART escape character register */ +#define UART_UTIM 0x00a0 /* UART escape timer register */ +#define UART_UBIR 0x00a4 /* UART BRM incremental register */ +#define UART_UBMR 0x00a8 /* UART BRM modulator register */ +#define UART_UBRC 0x00ac /* UART baud rate counter register */ +#define UART_BIPR1 0x00b0 /* UART BRM incremental preset register 1 */ +#define UART_BIPR2 0x00b4 /* UART BRM incremental preset register 2 */ +#define UART_BIPR3 0x00b8 /* UART BRM incremental preset register 3 */ +#define UART_BIPR4 0x00bc /* UART BRM incremental preset register 4 */ +#define UART_BMPR1 0x00c0 /* UART BRM modulator preset register 1 */ +#define UART_BMPR2 0x00c4 /* UART BRM modulator preset register 2 */ +#define UART_BMPR3 0x00c8 /* UART BRM modulator preset register 3 */ +#define UART_BMPR4 0x00cc /* UART BRM modulator preset register 4 */ +#define UART_UTS 0x00d0 /* UART test register */ + +/* UART Register Bit Definitions ****************************************************/ + +/* UART Receiver Register */ + +#define UART_RXD_DATA_SHIFT 0 /* Bits 0-7: Received Data */ +#define UART_RXD_DATA_MASK (0x7f << UART_RXD_DATA_SHIFT) +#define UART_RXD_PRERR (1 << 10) /* Bit 10: Parity Error */ +#define UART_RXD_BRK (1 << 11) /* Bit 11: Break Detect */ +#define UART_RXD_FRMERR (1 << 12) /* Bit 12: Frame Error */ +#define UART_RXD_OVRRUN (1 << 13) /* Bit 13: Receiver Overrun */ +#define UART_RXD_ERR (1 << 14) /* Bit 14: Error Detect */ +#define UART_RXD_CHARRDY (1 << 15) /* Bit 15: Character Ready */ + +/* UART Transmitter Register */ + +#define UART_TXDATA_SHIFT 0 /* Bits 0-7: Transmit Data */ +#define UART_TXDATA_MASK (0xff << UART_UCR4_TXDATA_SHIFT) + +/* UART Control Register 1 */ + +#define UART_UCR1_UARTEN (1 << 0) /* Bit 0: Enable/disable uart */ +#define UART_UCR1_DOZE (1 << 1) /* Bit 1: UART Doze enable */ +#define UART_UCR1_UARTCLEN (1 << 2) /* Bit 2: UART clock enable */ +#define UART_UCR1_TDMAEN (1 << 3) /* Bit 3: Transmitter ready data enable */ +#define UART_UCR1_SNDBRK (1 << 4) /* Bit 4: Send BREAK */ +#define UART_UCR1_RTSDEN (1 << 5) /* Bit 5: RTS Delta interrupt enable */ +#define UART_UCR1_TXEMPTYEN (1 << 6) /* Bit 6: Transmitter empty interrupt enable */ +#define UART_UCR1_IREN (1 << 7) /* Bit 7: Infrared Interface enable */ +#define UART_UCR1_RDMAEN (1 << 8) /* Bit 8: Receive ready DMA enable */ +#define UART_UCR1_RRDYEN (1 << 9) /* Bit 9: Receiver ready interrupt enable */ +#define UART_UCR1_ICD_SHIFT 10 /* Bit 10-11: Idle condition detect */ +#define UART_UCR1_ICD_MASK (0x03 << UART_UCR1_ICD_SHIFT) +#define UART_UCR1_IDEN (1 << 12) /* Bit 12: Idle condition detected interrupt enable */ +#define UART_UCR1_TRDYEN (1 << 13) /* Bit 13: Transmitter ready interrupt enable */ +#define UART_UCR1_ADBR (1 << 14) /* Bit 14: Automatic detection of baud rate */ +#define UART_UCR1_ADEN (1 << 15) /* Bit 15: Automatic baud rate detection interrupt enable */ + +/* UART Control Register 2 */ + +#define UART_UCR2_SRST (1 << 0) /* Bit 0: Software reset */ +#define UART_UCR2_RXEN (1 << 1) /* Bit 1: Receiver enable */ +#define UART_UCR2_TXEN (1 << 2) /* Bit 2: Transmitter enable */ +#define UART_UCR2_RTSEN (1 << 4) /* Bit 4: RTS interrupt enable/disable */ +#define UART_UCR2_WS (1 << 5) /* Bit 5: Word size */ +#define UART_UCR2_STPB (1 << 6) /* Bit 6: Controls number of stop bits */ +#define UART_UCR2_PROE (1 << 7) /* Bit 7: Parity Odd/Even */ +#define UART_UCR2_PREN (1 << 8) /* Bit 8: Parity enable */ +#define UART_UCR2_RTEC_SHIFT 9 /* Bit 9-10: Request to send edge control */ +#define UART_UCR2_RTEC_MASK (0x03 << UART_UCR2_RTEC_SHIFT) +#define UART_UCR2_ESCEN (1 << 11) /* Bit 11: Escape enable */ +#define UART_UCR2_CTS (1 << 12) /* Bit 12: Clear To Send pin */ +#define UART_UCR2_CTSC (1 << 13) /* Bit 13: CTS Pin control */ +#define UART_UCR2_IRTS (1 << 14) /* Bit 14: Ignore RTS Pin */ +#define UART_UCR2_ESCI (1 << 15) /* Bit 15: Escape Sequence Interrupt Enable */ + +/* UART1 Control Register 3 */ + +#define UART1_UCR3_BPEN (1 << 0) /* Bit 0: Preset Registers Enable */ +#define UART1_UCR3_INVT (1 << 1) /* Bit 1: Inverted Infrared Transmission */ +#define UART1_UCR3_REF30 (1 << 2) /* Bit 2: Reference frequency 30 mhz */ +#define UART1_UCR3_REF25 (1 << 3) /* Bit 3: Reference frequency 25 mhz */ +#define UART1_UCR3_AWAKEN (1 << 4) /* Bit 4: Asynchronous wake interrupt enable */ +#define UART1_UCR3_AIRINTEN (1 << 5) /* Bit 5: Asynchronous IR Wake interrupt enable */ +#define UART1_UCR3_RXDSEN (1 << 6) /* Bit 6: Receive status interrupt enable */ +#define UART1_UCR3_FRAERREN (1 << 11) /* Bit 11: Frame error interrupt enable */ +#define UART1_UCR3_PARERREN (1 << 12) /* Bit 12: Parity error interrupt enable */ + +/* UART2/3 Control Register 4 */ + +#define UART2_UCR3_BPEN (1 << 0) /* Bit 0: Preset Registers Enable */ +#define UART2_UCR3_INVT (1 << 1) /* Bit 1: Inverted Infrared Transmission */ +#define UART2_UCR3_REF30 (1 << 2) /* Bit 2: Reference frequency 30 mhz */ +#define UART2_UCR3_REF25 (1 << 3) /* Bit 3: Reference frequency 25 mhz */ +#define UART2_UCR3_AWAKEN (1 << 4) /* Bit 4: Asychronous WAKE Interrupt Enable */ +#define UART2_UCR3_AIRINTEN (1 << 5) /* Bit 5: Asychronous IR WAKE Interrupt Enable */ +#define UART2_UCR3_RXDSEN (1 << 6) /* Bit 6: Receive Status Interrupt Enable */ +#define UART2_UCR3_RI (1 << 7) /* Bit 7: Ring Indicator */ +#define UART2_UCR3_Reserved2 (1 << 8) /* Bit 8: Reserved */ +#define UART2_UCR3_DCD (1 << 9) /* Bit 9: Data Carrier Detect */ +#define UART2_UCR3_DSR (1 << 10) /* Bit 10: Data Set Ready */ +#define UART2_UCR3_FRAERREN (1 << 11) /* Bit 11: Frame Error Interrupt Enable */ +#define UART2_UCR3_PARERREN (1 << 12) /* Bit 12: Parity Error Interrupt Enable */ +#define UART2_UCR3_DTREN (1 << 13) /* Bit 13: Data Terminal Ready Interrupt Enable */ +#define UART2_UCR3_DPEC_SHIFT 14 /* Bit 14-15: DTR Interrupt Edge Control */ +#define UART2_UCR3_DPEC_SHIFT (0x03 << UART_UCR4_DPEC_SHIFT) + +/* UART Control Register 4 */ + +#define UART_UCR4_DREN (1 << 0) /* Bit 0: Receive data ready interrupt enable */ +#define UART_UCR4_OREN (1 << 1) /* Bit 1: Receiver overrun interrupt enable */ +#define UART_UCR4_BKEN (1 << 2) /* Bit 2: Break condition detected interrupt enable */ +#define UART_UCR4_TCEN (1 << 3) /* Bit 3: Transmit complete interrupt enable */ +#define UART_UCR4_IRSC (1 << 5) /* Bit 5: IR special case */ +#define UART_UCR4_REF16 (1 << 6) /* Bit 6: Reference Frequency 16 mhz */ +#define UART_UCR4_WKEN (1 << 7) /* Bit 7: Wake interrupt enable */ +#define UART_UCR4_ENIRI (1 << 8) /* Bit 8: Serial infrared interrupt enable */ +#define UART_UCR4_INVR (1 << 9) /* Bit 9: Inverted infrared reception */ +#define UART_UCR4_CTSTL_SHIFT 10 /* Bits 10-15: CTS trigger level */ +#define UART_UCR4_CTSTL_MASK (0x3f << UART_UCR4_CTSTL_SHIFT) + +/* UART FIFO Control Register */ + +#define UART_UFCR_RXTL_SHIFT 0 /* Bits 0-6: Receiver Trigger Level */ +#define UART_UFCR_RXTL_MASK (0x3f << UART_UFCR_RXTL_SHIFT) +#define UART_UFCR_RFDIV_SHIFT 7 /* Bits 7-9: Reference Frequency Divider */ +#define UART_UFCR_RFDIV_MASK (0x07 << UART_UFCR_RFDIV_SHIFT) +#define UART_UFCR_TXTL_SHIFT 10 /* Bits 10-15: Transmitter Trigger Level */ +#define UART_UFCR_TXTL_MASK (0x3f << UART_UFCR_TXTL_SHIFT) + +/* UART Status 1 Register */ + +#define UART_USR1_AWAKE (1 << 4) /* Bit 4: Asynchronous WAKE Interrupt Flag */ +#define UART_USR1_AIRINT (1 << 5) /* Bit 5: Asynchronous IR WAKE Interrupt Flag */ +#define UART_USR1_RXDS (1 << 6) /* Bit 6: Receiver IDLE Interrupt Flag */ +#define UART_USR1_RRDY (1 << 9) /* Bit 9: RX Ready Interrupt/DMA Flag */ +#define UART_USR1_FRAMERR (1 << 10) /* Bit 10: Frame Error Interrupt Flag */ +#define UART_USR1_ESCF (1 << 11) /* Bit 11: Escape Sequence Interrupt Flag */ +#define UART_USR1_RTSD (1 << 12) /* Bit 12: RTS Delta */ +#define UART_USR1_TRDY (1 << 13) /* Bit 13: TX Ready Interrupt/DMA Flag */ +#define UART_USR1_RTSS (1 << 14) /* Bit 14: RTS Pin Status */ +#define UART_USR1_PARITYERR (1 << 15) /* Bit 15: Parity Error Interrupt Flag */ + +/* UART Status 2 Register */ + +#define UART_USR2_RDR (1 << 0) /* Bit 0: Receive data ready */ +#define UART_USR2_ORE (1 << 1) /* Bit 1: Overrun error */ +#define UART_USR2_BRCD (1 << 2) /* Bit 2: Break condition detected */ +#define UART_USR2_TXDC (1 << 3) /* Bit 3: Transmitter complete */ +#define UART_USR2_RTSF (1 << 4) /* Bit 4: RTS Edge Triggered Interrupt flag */ +#define UART_USR2_WAKE (1 << 7) /* Bit 7: Wake */ +#define UART_USR2_IRINT (1 << 8) /* Bit 8: Serial infrared interrupt flag */ +#define UART_USR2_IDLE (1 << 12) /* Bit 12: Idle condition */ +#define UART_USR2_DTRF (1 << 13) /* Bit 13: DTR edge triggered interrupt flag */ +#define UART_USR2_TXFE (1 << 14) /* Bit 14: Transmit Buffer FIFO empty */ +#define UART_USR2_ADET (1 << 15) /* Bit 15: Automatic baud rate detection complete */ + +/************************************************************************************ + * Inline Functions + ************************************************************************************/ + +#endif /* __ARCH_ARM_IMX_UART_H */ |