diff options
Diffstat (limited to 'nuttx/configs/eagle100/README.txt')
-rw-r--r-- | nuttx/configs/eagle100/README.txt | 38 |
1 files changed, 19 insertions, 19 deletions
diff --git a/nuttx/configs/eagle100/README.txt b/nuttx/configs/eagle100/README.txt index 3f9da652b..378f5a25b 100644 --- a/nuttx/configs/eagle100/README.txt +++ b/nuttx/configs/eagle100/README.txt @@ -334,15 +334,15 @@ Eagle100-specific Configuration Options Additional interrupt support can be disabled if desired to reduce memory footprint. - CONFIG_LM3S_DISABLE_GPIOA_IRQS=n - CONFIG_LM3S_DISABLE_GPIOB_IRQS=n - CONFIG_LM3S_DISABLE_GPIOC_IRQS=n - CONFIG_LM3S_DISABLE_GPIOD_IRQS=n - CONFIG_LM3S_DISABLE_GPIOE_IRQS=n - CONFIG_LM3S_DISABLE_GPIOF_IRQS=n - CONFIG_LM3S_DISABLE_GPIOG_IRQS=n - CONFIG_LM3S_DISABLE_GPIOH_IRQS=y - CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y + CONFIG_LM_DISABLE_GPIOA_IRQS=n + CONFIG_LM_DISABLE_GPIOB_IRQS=n + CONFIG_LM_DISABLE_GPIOC_IRQS=n + CONFIG_LM_DISABLE_GPIOD_IRQS=n + CONFIG_LM_DISABLE_GPIOE_IRQS=n + CONFIG_LM_DISABLE_GPIOF_IRQS=n + CONFIG_LM_DISABLE_GPIOG_IRQS=n + CONFIG_LM_DISABLE_GPIOH_IRQS=y + CONFIG_LM_DISABLE_GPIOJ_IRQS=y LM3S6818 specific device driver settings @@ -367,18 +367,18 @@ Eagle100-specific Configuration Options value is large, then larger values of this setting may cause Rx FIFO overrun errors. Default: half of the Tx FIFO size (4). - CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET) + CONFIG_LM_ETHERNET - This must be set (along with CONFIG_NET) to build the LM3S Ethernet driver - CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board. - CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide + CONFIG_LM_ETHLEDS - Enable to use Ethernet LEDs on the board. + CONFIG_LM_BOARDMAC - If the board-specific logic can provide a MAC address (via lm_ethernetmac()), then this should be selected. - CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation - CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation - CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding - CONFIG_LM3S_MULTICAST - Set to enable multicast frames - CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode - CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection. - CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console. + CONFIG_LM_ETHHDUPLEX - Set to force half duplex operation + CONFIG_LM_ETHNOAUTOCRC - Set to suppress auto-CRC generation + CONFIG_LM_ETHNOPAD - Set to suppress Tx padding + CONFIG_LM_MULTICAST - Set to enable multicast frames + CONFIG_LM_PROMISCUOUS - Set to enable promiscuous mode + CONFIG_LM_BADCRC - Set to enable bad CRC rejection. + CONFIG_LM_DUMPPACKET - Dump each packet received/sent to the console. Configurations ^^^^^^^^^^^^^^ |