diff options
Diffstat (limited to 'nuttx/configs/lm3s6432-s2e/README.txt')
| -rw-r--r-- | nuttx/configs/lm3s6432-s2e/README.txt | 38 |
1 files changed, 19 insertions, 19 deletions
diff --git a/nuttx/configs/lm3s6432-s2e/README.txt b/nuttx/configs/lm3s6432-s2e/README.txt index 91e4f0f71..f81866a08 100644 --- a/nuttx/configs/lm3s6432-s2e/README.txt +++ b/nuttx/configs/lm3s6432-s2e/README.txt @@ -346,15 +346,15 @@ Stellaris MDL-S2E Reference Design Configuration Options Additional interrupt support can be disabled if desired to reduce memory footprint - GPIOs C-G are not pinned out on the MDL-S2E board. - CONFIG_LM_DISABLE_GPIOA_IRQS=n - CONFIG_LM_DISABLE_GPIOB_IRQS=n - CONFIG_LM_DISABLE_GPIOC_IRQS=y - CONFIG_LM_DISABLE_GPIOD_IRQS=y - CONFIG_LM_DISABLE_GPIOE_IRQS=y - CONFIG_LM_DISABLE_GPIOF_IRQS=y - CONFIG_LM_DISABLE_GPIOG_IRQS=y - CONFIG_LM_DISABLE_GPIOH_IRQS=y - CONFIG_LM_DISABLE_GPIOJ_IRQS=y + CONFIG_TIVA_DISABLE_GPIOA_IRQS=n + CONFIG_TIVA_DISABLE_GPIOB_IRQS=n + CONFIG_TIVA_DISABLE_GPIOC_IRQS=y + CONFIG_TIVA_DISABLE_GPIOD_IRQS=y + CONFIG_TIVA_DISABLE_GPIOE_IRQS=y + CONFIG_TIVA_DISABLE_GPIOF_IRQS=y + CONFIG_TIVA_DISABLE_GPIOG_IRQS=y + CONFIG_TIVA_DISABLE_GPIOH_IRQS=y + CONFIG_TIVA_DISABLE_GPIOJ_IRQS=y LM3S6432 specific device driver settings @@ -388,18 +388,18 @@ Stellaris MDL-S2E Reference Design Configuration Options value is large, then larger values of this setting may cause Rx FIFO overrun errors. Default: half of the Tx FIFO size (4). - CONFIG_LM_ETHERNET - This must be set (along with CONFIG_NET) + CONFIG_TIVA_ETHERNET - This must be set (along with CONFIG_NET) to build the Stellaris Ethernet driver - CONFIG_LM_ETHLEDS - Enable to use Ethernet LEDs on the board. - CONFIG_LM_BOARDMAC - This should be set in order to use the + CONFIG_TIVA_ETHLEDS - Enable to use Ethernet LEDs on the board. + CONFIG_TIVA_BOARDMAC - This should be set in order to use the MAC address configured in the flash USER registers. - CONFIG_LM_ETHHDUPLEX - Set to force half duplex operation - CONFIG_LM_ETHNOAUTOCRC - Set to suppress auto-CRC generation - CONFIG_LM_ETHNOPAD - Set to suppress Tx padding - CONFIG_LM_MULTICAST - Set to enable multicast frames - CONFIG_LM_PROMISCUOUS - Set to enable promiscuous mode - CONFIG_LM_BADCRC - Set to enable bad CRC rejection. - CONFIG_LM_DUMPPACKET - Dump each packet received/sent to the console. + CONFIG_TIVA_ETHHDUPLEX - Set to force half duplex operation + CONFIG_TIVA_ETHNOAUTOCRC - Set to suppress auto-CRC generation + CONFIG_TIVA_ETHNOPAD - Set to suppress Tx padding + CONFIG_TIVA_MULTICAST - Set to enable multicast frames + CONFIG_TIVA_PROMISCUOUS - Set to enable promiscuous mode + CONFIG_TIVA_BADCRC - Set to enable bad CRC rejection. + CONFIG_TIVA_DUMPPACKET - Dump each packet received/sent to the console. Configurations ^^^^^^^^^^^^^^ |