diff options
Diffstat (limited to 'nuttx/configs/sam4l-xplained/src/sam4l-xplained.h')
-rw-r--r-- | nuttx/configs/sam4l-xplained/src/sam4l-xplained.h | 140 |
1 files changed, 140 insertions, 0 deletions
diff --git a/nuttx/configs/sam4l-xplained/src/sam4l-xplained.h b/nuttx/configs/sam4l-xplained/src/sam4l-xplained.h new file mode 100644 index 000000000..edeb24fe1 --- /dev/null +++ b/nuttx/configs/sam4l-xplained/src/sam4l-xplained.h @@ -0,0 +1,140 @@ +/************************************************************************************ + * configs/sam3uek_eval/src/sam4l-xplained.h + * + * Copyright (C) 2009-2011, 2013 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt <gnutt@nuttx.org> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ************************************************************************************/ + +#ifndef __CONFIGS_SAM4L_XPLAINED_SRC_SAM4L_XPLAINED_H +#define __CONFIGS_SAM4L_XPLAINED_SRC_SAM4L_XPLAINED_H + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include <nuttx/config.h> +#include <nuttx/compiler.h> + +#include <stdint.h> + +#include <arch/irq.h> +#include <nuttx/irq.h> + +#include "chip/sam_pinmap.h" + +/************************************************************************************ + * Pre-processor Definitions + ************************************************************************************/ +/* LEDs: There are three LEDs on board the SAM4L Xplained Pro board: The EDBG + * controls two of the LEDs, a power LED and a status LED. There is only + * one user controllable LED, a yellow LED labeled LED0 near the SAM4L USB + * connector. + * + * This LED is controlled by PC07 and LED0 can be activated by driving the + * PC07 to GND. + * + * When CONFIG_ARCH_LEDS is defined in the NuttX configuration, NuttX will + * control LED0 as follows: + * + * SYMBOL Meaning LED0 + * ------------------- ----------------------- ------ + * LED_STARTED NuttX has been started OFF + * LED_HEAPALLOCATE Heap has been allocated OFF + * LED_IRQSENABLED Interrupts enabled OFF + * LED_STACKCREATED Idle stack created ON + * LED_INIRQ In an interrupt N/C + * LED_SIGNAL In a signal handler N/C + * LED_ASSERTION An assertion failed N/C + * LED_PANIC The system has crashed FLASH + * + * Thus is LED0 is statically on, NuttX has successfully booted and is, + * apparently, running normmally. If LED0 is flashing at approximately + * 2Hz, then a fatal error has been detected and the system has halted. + */ + +#define GPIO_LED0 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_PORT_PIOC | \ + GPIO_OUTPUT_SET | GPIO_PIN7) + +/* QTouch button: The SAM4L Xplained Pro kit has one QTouch button. The connection + * to the SAM4L is: + * + * PC13 CATB_SENSE15 + * PC14 CATB_DIS + */ + +/* Mechanical buttons: + * + * The SAM4L Xplained Pro contains two mechanical buttons. One button is the + * RESET button connected to the SAM4L reset line and the other is a generic user + * configurable button. When a button is pressed it will drive the I/O line to GND. + * + * PC24 SW0 + */ + +#define GPIO_SW0 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \ + GPIO_PORT_PIOC | GPIO_PIN24) +#define IRQ_SW0 SAM_IRQ_PC24 + +/************************************************************************************ + * Public Types + ************************************************************************************/ + +/************************************************************************************ + * Public data + ************************************************************************************/ + +#ifndef __ASSEMBLY__ + +/************************************************************************************ + * Public Functions + ************************************************************************************/ + +/************************************************************************************ + * Name: sam_spiinitialize + * + * Description: + * Called to configure SPI chip select GPIO pins for the SAM3U-EK board. + * + ************************************************************************************/ + +void weak_function sam_spiinitialize(void); + +/**************************************************************************** + * Name: up_ledinit + ****************************************************************************/ + +#ifdef CONFIG_ARCH_LEDS +void up_ledinit(void); +#endif + +#endif /* __ASSEMBLY__ */ +#endif /* __CONFIGS_SAM4L_XPLAINED_SRC_SAM4L_XPLAINED_H */ + |