diff options
Diffstat (limited to 'nuttx/configs/stm3220g-eval/nsh/defconfig')
-rw-r--r-- | nuttx/configs/stm3220g-eval/nsh/defconfig | 1421 |
1 files changed, 1421 insertions, 0 deletions
diff --git a/nuttx/configs/stm3220g-eval/nsh/defconfig b/nuttx/configs/stm3220g-eval/nsh/defconfig new file mode 100644 index 000000000..4497c487f --- /dev/null +++ b/nuttx/configs/stm3220g-eval/nsh/defconfig @@ -0,0 +1,1421 @@ +############################################################################ +# configs/stm3220g-eval/nsh/defconfig +# +# Copyright (C) 2011-2012 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ +# +# architecture selection +# +# CONFIG_ARCH - identifies the arch subdirectory and, hence, the +# processor architecture. +# CONFIG_ARCH_family - for use in C code. This identifies the +# particular chip family that the architecture is implemented +# in. +# CONFIG_ARCH_architecture - for use in C code. This identifies the +# specific architecture within the chip familyl. +# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory +# CONFIG_ARCH_CHIP_name - For use in C code +# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, +# the board that supports the particular chip or SoC. +# CONFIG_ARCH_BOARD_name - for use in C code +# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) +# CONFIG_BOARD_LOOPSPERMSEC - for delay loops +# CONFIG_DRAM_SIZE - Describes the installed DRAM. +# CONFIG_DRAM_START - The start address of DRAM (physical) +# CONFIG_DRAM_END - Last address+1 of installed RAM +# CONFIG_ARCH_IRQPRIO - The STM3220xxx supports interrupt prioritization +# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt +# stack. If defined, this symbol is the size of the interrupt +# stack in bytes. If not defined, the user task stacks will be +# used during interrupt handling. +# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions +# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. +# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. +# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. +# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that +# cause a 100 second delay during boot-up. This 100 second delay +# serves no purpose other than it allows you to calibrate +# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure +# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until +# the delay actually is 100 seconds. +# CONFIG_ARCH_DMA - Support DMA initialization +# +CONFIG_ARCH=arm +CONFIG_ARCH_ARM=y +CONFIG_ARCH_CORTEXM3=y +CONFIG_ARCH_CHIP=stm32 +CONFIG_ARCH_CHIP_STM32F207IG=y +CONFIG_ARCH_BOARD=stm3220g-eval +CONFIG_ARCH_BOARD_STM3220G_EVAL=y +CONFIG_BOARD_LOOPSPERMSEC=16717 +CONFIG_DRAM_SIZE=0x00030000 +CONFIG_DRAM_START=0x20000000 +CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE) +CONFIG_ARCH_IRQPRIO=y +CONFIG_ARCH_INTERRUPTSTACK=n +CONFIG_ARCH_STACKDUMP=y +CONFIG_ARCH_BOOTLOADER=n +CONFIG_ARCH_LEDS=y +CONFIG_ARCH_BUTTONS=n +CONFIG_ARCH_CALIBRATION=n +CONFIG_ARCH_DMA=n + +# +# Identify toolchain and linker options +# +CONFIG_STM32_CODESOURCERYW=n +CONFIG_STM32_CODESOURCERYL=n +CONFIG_STM32_DEVKITARM=n +CONFIG_STM32_RAISONANCE=n +CONFIG_STM32_BUILDROOT=y + +# +# JTAG Enable settings (by default JTAG-DP and SW-DP are disabled): +# +# CONFIG_STM32_DFU - Use the DFU bootloader, not JTAG +# +# JTAG Enable options: +# +# CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP) +# CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP) +# but without JNTRST. +# CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled +# +CONFIG_STM32_DFU=n +CONFIG_STM32_JTAG_FULL_ENABLE=y +CONFIG_STM32_JTAG_NOJNTRST_ENABLE=n +CONFIG_STM32_JTAG_SW_ENABLE=n + +# +# Individual subsystems can be enabled: +# +# Individual subsystems can be enabled: +# AHB1: +CONFIG_STM32_CRC=n +CONFIG_STM32_BKPSRAM=n +CONFIG_STM32_CCMDATARAM=n +CONFIG_STM32_DMA1=n +CONFIG_STM32_DMA2=n +CONFIG_STM32_ETHMAC=y +CONFIG_STM32_OTGHS=n +# AHB2: +CONFIG_STM32_DCMI=n +CONFIG_STM32_CRYP=n +CONFIG_STM32_HASH=n +CONFIG_STM32_RNG=n +CONFIG_STM32_OTGFS=n +# AHB3: +CONFIG_STM32_FSMC=n +# APB1: +CONFIG_STM32_TIM2=n +CONFIG_STM32_TIM3=n +CONFIG_STM32_TIM4=n +CONFIG_STM32_TIM5=n +CONFIG_STM32_TIM6=n +CONFIG_STM32_TIM7=n +CONFIG_STM32_TIM12=n +CONFIG_STM32_TIM13=n +CONFIG_STM32_TIM14=n +CONFIG_STM32_WWDG=n +CONFIG_STM32_SPI2=n +CONFIG_STM32_SPI3=n +CONFIG_STM32_USART2=n +CONFIG_STM32_USART3=y +CONFIG_STM32_UART4=n +CONFIG_STM32_UART5=n +CONFIG_STM32_I2C1=y +CONFIG_STM32_I2C2=n +CONFIG_STM32_I2C3=n +CONFIG_STM32_CAN1=n +CONFIG_STM32_CAN2=n +CONFIG_STM32_DAC=n +CONFIG_STM32_PWR=y +# APB2: +CONFIG_STM32_TIM1=n +CONFIG_STM32_TIM8=n +CONFIG_STM32_USART1=n +CONFIG_STM32_USART6=n +CONFIG_STM32_ADC1=n +CONFIG_STM32_ADC2=n +CONFIG_STM32_ADC3=n +CONFIG_STM32_SDIO=n +CONFIG_STM32_SPI1=n +CONFIG_STM32_SYSCFG=y +CONFIG_STM32_TIM9=n +CONFIG_STM32_TIM10=n +CONFIG_STM32_TIM11=n + +# +# Timer and I2C devices may need to the following to force power to be applied: +# +#CONFIG_STM32_FORCEPOWER=y + +# +# STM32F20xxx specific serial device driver settings +# +# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the +# console and ttys0 (default is the USART1). +# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received. +# This specific the size of the receive buffer +# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before +# being sent. This specific the size of the transmit buffer +# CONFIG_USARTn_BAUD - The configure BAUD of the UART. Must be +# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8. +# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity +# CONFIG_USARTn_2STOP - Two stop bits +# +CONFIG_USART1_SERIAL_CONSOLE=n +CONFIG_USART2_SERIAL_CONSOLE=n +CONFIG_USART3_SERIAL_CONSOLE=y +CONFIG_USART4_SERIAL_CONSOLE=n +CONFIG_USART5_SERIAL_CONSOLE=n + +CONFIG_USART1_TXBUFSIZE=128 +CONFIG_USART2_TXBUFSIZE=128 +CONFIG_USART3_TXBUFSIZE=128 +CONFIG_USART4_TXBUFSIZE=128 +CONFIG_USART5_TXBUFSIZE=128 + +CONFIG_USART1_RXBUFSIZE=128 +CONFIG_USART2_RXBUFSIZE=128 +CONFIG_USART3_RXBUFSIZE=128 +CONFIG_USART4_RXBUFSIZE=128 +CONFIG_USART5_RXBUFSIZE=128 + +CONFIG_USART1_BAUD=115200 +CONFIG_USART2_BAUD=115200 +CONFIG_USART3_BAUD=115200 +CONFIG_USART4_BAUD=115200 +CONFIG_USART5_BAUD=115200 + +CONFIG_USART1_BITS=8 +CONFIG_USART2_BITS=8 +CONFIG_USART3_BITS=8 +CONFIG_USART4_BITS=8 +CONFIG_USART5_BITS=8 + +CONFIG_USART1_PARITY=0 +CONFIG_USART2_PARITY=0 +CONFIG_USART3_PARITY=0 +CONFIG_USART4_PARITY=0 +CONFIG_USART5_PARITY=0 + +CONFIG_USART1_2STOP=0 +CONFIG_USART2_2STOP=0 +CONFIG_USART3_2STOP=0 +CONFIG_USART4_2STOP=0 +CONFIG_USART5_2STOP=0 + +# +# STM32F20xxx specific SSI device driver settings +# +# CONFIG_SSIn_DISABLE - select to disable all support for +# the SSI +# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support +# Poll-waiting is recommended if the interrupt rate would be to +# high in the interrupt driven case. +# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before +# emptying the Rx FIFO. If the SPI frequency is high and this +# value is large, then larger values of this setting may cause +# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4). +# +CONFIG_SSI0_DISABLE=n +CONFIG_SSI1_DISABLE=y +CONFIG_SSI_POLLWAIT=y +#CONFIG_SSI_TXLIMIT=4 + +# +# STM32F20xxx specific CAN device driver settings +# +# CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or +# CONFIG_STM32_CAN2 must also be defined) +# CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default +# Standard 11-bit IDs. +# CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages. +# Default: 8 +# CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests. +# Default: 4 +# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback +# mode for testing. The STM32 CAN driver does support loopback mode. +# CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined. +# CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined. +# CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6 +# CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7 +# +CONFIG_CAN=n +CONFIG_CAN_EXTID=n +#CONFIG_CAN_FIFOSIZE +#CONFIG_CAN_NPENDINGRTR +CONFIG_CAN_LOOPBACK=n +CONFIG_CAN1_BAUD=700000 +CONFIG_CAN2_BAUD=700000 + +# +# STM32F20xxx Ethernet device driver settings +# +# CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board +# CONFIG_STM32_MII - Support Ethernet MII interface +# CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface +# CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface +# CONFIG_STM32_RMII - Support Ethernet RMII interface +# CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode +# CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this +# may be defined to select full duplex mode. Default: half-duplex +# CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this +# may be defined to select 100 MBps speed. Default: 10 Mbps +# CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is +# defined. The PHY status register address may diff from PHY to PHY. This +# configuration sets the address of the PHY status register. +# CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides bit mask indicating 10 or 100MBps speed. +# CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides the value of the speed bit(s) indicating 100MBps speed. +# CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provide bit mask indicating full or half duplex modes. +# CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides the value of the mode bits indicating full duplex mode. +# CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported +# but some hooks are indicated with this condition. +# CONFIG_STM32_ETHMAC_REGDEBUG - If CONFIG_DEBUG is also enabled, this will +# generate far more debug output than you could ever care to see unless you +# are debugging low-level Ethernet driver features. +# +CONFIG_STM32_PHYADDR=0x01 +CONFIG_STM32_MII=y +CONFIG_STM32_MII_MCO1=y +CONFIG_STM32_MII_MCO2=n +CONFIG_STM32_RMII=n +CONFIG_STM32_AUTONEG=y +#CONFIG_STM32_ETHFD +#CONFIG_STM32_ETH100MB +CONFIG_STM32_PHYSR=16 +CONFIG_STM32_PHYSR_SPEED=0x0002 +CONFIG_STM32_PHYSR_100MBPS=0x0000 +CONFIG_STM32_PHYSR_MODE=0x0004 +CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004 +CONFIG_STM32_ETH_PTP=n +CONFIG_STM32_ETHMAC_REGDEBUG=n + +# +# I2C configuration +# +CONFIG_I2C=y +CONFIG_I2C_POLLED=y +CONFIG_I2C_TRANSFER=y +CONFIG_I2C_TRACE=n + +# +# ADC configuration +# +# Enable ADC driver support. The STM3220G-EVAL has a 10 Kohm potentiometer +# RV1 connected to PF9 of STM32F207IGH6 on the board: TIM14_CH1/ SMC_CD/ADC3_IN7 +# In order to use the ADC, you must make the following selections: +# +# Above: +# CONFIG_STM32_ADC3=y : Enable ADC3 +# CONFIG_STM32_TIM1=y : Enable Timer 1 +# +# Below: +# CONFIG_ADC=y : Enable the generic ADC infrastructure +# CONFIG_STM32_TIM1_ADC=y : Indicate that timer 1 will be used to trigger an ADC +# CONFIG_STM32_TIM1_ADC3=y : Assign timer 1 to drive ADC3 sampling +# CONFIG_STM32_ADC3_SAMPLE_FREQUENCY=100 : Select a sampling frequency +# +CONFIG_ADC=n +#CONFIG_STM32_TIM1_ADC=y +CONFIG_STM32_TIM1_ADC3=y +CONFIG_STM32_ADC3_SAMPLE_FREQUENCY=100 + +# +# PWM configuration +# +# The STM3220G-Eval has no real on-board PWM devices, but the board can be configured to output +# a pulse train using several options (see board.h). Here the default setup is for TIM8, CH4. +# Don't forget to enable CONFIG_PWM and CONFIG_STM32_TIM8. +# +CONFIG_PWM=n +CONFIG_PWM_PULSECOUNT=y +CONFIG_STM32_TIM8_PWM=y +CONFIG_STM32_TIM8_CHANNEL=4 + +# +# General build options +# +# CONFIG_RRLOAD_BINARY - make the rrload binary format used with +# BSPs from www.ridgerun.com using the tools/mkimage.sh script +# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_RAW_BINARY - make a raw binary format file used with many +# different loaders using the GNU objcopy program. This option +# should not be selected if you are not using the GNU toolchain. +# CONFIG_HAVE_LIBM - toolchain supports libm.a +# +CONFIG_RRLOAD_BINARY=n +CONFIG_INTELHEX_BINARY=y +CONFIG_MOTOROLA_SREC=n +CONFIG_RAW_BINARY=n +CONFIG_HAVE_LIBM=n + +# +# General OS setup +# +# CONFIG_APPS_DIR - Identifies the relative path to the directory +# that builds the application to link with NuttX. Default: ../apps +# CONFIG_DEBUG - enables built-in debug options +# CONFIG_DEBUG_VERBOSE - enables verbose debug output +# CONFIG_DEBUG_SYMBOLS - build without optimization and with +# debug symbols (needed for use with a debugger). +# CONFIG_HAVE_CXX - Enable support for C++ +# CONFIG_MM_REGIONS - If the architecture includes multiple +# regions of memory to allocate from, this specifies the +# number of memory regions that the memory manager must +# handle and enables the API mm_addregion(start, end); +# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot +# time console output +# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz +# or MSEC_PER_TICK=10. This setting may be defined to +# inform NuttX that the processor hardware is providing +# system timer interrupts at some interrupt interval other +# than 10 msec. +# CONFIG_RR_INTERVAL - The round robin timeslice will be set +# this number of milliseconds; Round robin scheduling can +# be disabled by setting this value to zero. +# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in +# scheduler to monitor system performance +# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a +# task name to save in the TCB. Useful if scheduler +# instrumentation is selected. Set to zero to disable. +# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - +# Used to initialize the internal time logic. +# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. +# You would only need this if you are concerned about accurate +# time conversions in the past or in the distant future. +# CONFIG_JULIAN_TIME - Enables Julian time conversions. You +# would only need this if you are concerned about accurate +# time conversion in the distand past. You must also define +# CONFIG_GREGORIAN_TIME in order to use Julian time. +# CONFIG_DEV_CONSOLE - Set if architecture-specific logic +# provides /dev/console. Enables stdout, stderr, stdin. +# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console +# driver (minimul support) +# CONFIG_MUTEX_TYPES: Set to enable support for recursive and +# errorcheck mutexes. Enables pthread_mutexattr_settype(). +# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority +# inheritance on mutexes and semaphores. +# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority +# inheritance is enabled. It defines the maximum number of +# different threads (minus one) that can take counts on a +# semaphore with priority inheritance support. This may be +# set to zero if priority inheritance is disabled OR if you +# are only using semaphores as mutexes (only one holder) OR +# if no more than two threads participate using a counting +# semaphore. +# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, +# then this setting is the maximum number of higher priority +# threads (minus 1) than can be waiting for another thread +# to release a count on a semaphore. This value may be set +# to zero if no more than one thread is expected to wait for +# a semaphore. +# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors +# by task_create() when a new task is started. If set, all +# files/drivers will appear to be closed in the new task. +# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first +# three file descriptors (stdin, stdout, stderr) by task_create() +# when a new task is started. If set, all files/drivers will +# appear to be closed in the new task except for stdin, stdout, +# and stderr. +# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket +# desciptors by task_create() when a new task is started. If +# set, all sockets will appear to be closed in the new task. +# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to +# handle delayed processing from interrupt handlers. This feature +# is required for some drivers but, if there are not complaints, +# can be safely disabled. The worker thread also performs +# garbage collection -- completing any delayed memory deallocations +# from interrupt handlers. If the worker thread is disabled, +# then that clean will be performed by the IDLE thread instead +# (which runs at the lowest of priority and may not be appropriate +# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE +# is enabled, then the following options can also be used: +# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker +# thread. Default: 50 +# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for +# work in units of microseconds. Default: 50*1000 (50 MS). +# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker +# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. +# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up +# the worker thread. Default: 4 +# CONFIG_SCHED_WAITPID - Enable the waitpid() API +# CONFIG_SCHED_ATEXIT - Enabled the atexit() API +# +#CONFIG_APPS_DIR= +CONFIG_DEBUG=y +CONFIG_DEBUG_VERBOSE=y +CONFIG_DEBUG_SYMBOLS=y +CONFIG_DEBUG_FS=n +CONFIG_DEBUG_GRAPHICS=n +CONFIG_DEBUG_LCD=n +CONFIG_DEBUG_USB=n +CONFIG_DEBUG_NET=n +CONFIG_DEBUG_RTC=n +CONFIG_DEBUG_ANALOG=n +CONFIG_DEBUG_PWM=n +CONFIG_DEBUG_CAN=n +CONFIG_DEBUG_I2C=n +CONFIG_HAVE_CXX=n +CONFIG_MM_REGIONS=1 +CONFIG_ARCH_LOWPUTC=y +CONFIG_RR_INTERVAL=200 +CONFIG_SCHED_INSTRUMENTATION=n +CONFIG_TASK_NAME_SIZE=0 +CONFIG_START_YEAR=2011 +CONFIG_START_MONTH=12 +CONFIG_START_DAY=6 +CONFIG_GREGORIAN_TIME=n +CONFIG_JULIAN_TIME=n +CONFIG_DEV_CONSOLE=y +CONFIG_DEV_LOWCONSOLE=n +CONFIG_MUTEX_TYPES=n +CONFIG_PRIORITY_INHERITANCE=n +CONFIG_SEM_PREALLOCHOLDERS=0 +CONFIG_SEM_NNESTPRIO=0 +CONFIG_FDCLONE_DISABLE=n +CONFIG_FDCLONE_STDIO=n +CONFIG_SDCLONE_DISABLE=y +CONFIG_SCHED_WORKQUEUE=n +CONFIG_SCHED_WORKPRIORITY=192 +CONFIG_SCHED_WORKPERIOD=(50*1000) +CONFIG_SCHED_WORKSTACKSIZE=1024 +CONFIG_SIG_SIGWORK=4 +CONFIG_SCHED_WAITPID=y +CONFIG_SCHED_ATEXIT=n + +# +# System Logging +# +# CONFIG_SYSLOG - Enables the System Logging feature. +# CONFIG_RAMLOG - Enables the RAM logging feature +# CONFIG_RAMLOG_CONSOLE - Use the RAM logging device as a system console. +# If this feature is enabled (along with CONFIG_DEV_CONSOLE), then all +# console output will be re-directed to a circular buffer in RAM. This +# is useful, for example, if the only console is a Telnet console. Then +# in that case, console output from non-Telnet threads will go to the +# circular buffer and can be viewed using the NSH 'dmesg' command. +# CONFIG_RAMLOG_SYSLOG - Use the RAM logging device for the syslogging +# interface. If this feature is enabled (along with CONFIG_SYSLOG), +# then all debug output (only) will be re-directed to the circular +# buffer in RAM. This RAM log can be view from NSH using the 'dmesg' +# command. +# CONFIG_RAMLOG_NPOLLWAITERS - The number of threads than can be waiting +# for this driver on poll(). Default: 4 +# +# If CONFIG_RAMLOG_CONSOLE or CONFIG_RAMLOG_SYSLOG is selected, then the +# following may also be provided: +# +# CONFIG_RAMLOG_CONSOLE_BUFSIZE - Size of the console RAM log. Default: 1024 +# + +CONFIG_SYSLOG=n +CONFIG_RAMLOG=n +CONFIG_RAMLOG_CONSOLE=n +CONFIG_RAMLOG_SYSLOG=n +#CONFIG_RAMLOG_NPOLLWAITERS +#CONFIG_RAMLOG_CONSOLE_BUFSIZE + +# +# Settings for NXFLAT +# +# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. +# This format will support execution of NuttX binaries located +# in a ROMFS filesystem (see examples/nxflat). +# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals +# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and +# CONFIG_DEBUG_BINFMT have to be defined or +# CONFIG_NXFLAT_DUMPBUFFER does nothing. +# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table +# is ordered by symbol name +# +CONFIG_NXFLAT=n +CONFIG_NXFLAT_DUMPBUFFER=n +CONFIG_SYMTAB_ORDEREDBYNAME=y + +# +# The following can be used to disable categories of +# APIs supported by the OS. If the compiler supports +# weak functions, then it should not be necessary to +# disable functions unless you want to restrict usage +# of those APIs. +# +# There are certain dependency relationships in these +# features. +# +# o mq_notify logic depends on signals to awaken tasks +# waiting for queues to become full or empty. +# o pthread_condtimedwait() depends on signals to wake +# up waiting tasks. +# +CONFIG_DISABLE_CLOCK=n +CONFIG_DISABLE_POSIX_TIMERS=n +CONFIG_DISABLE_PTHREAD=n +CONFIG_DISABLE_SIGNALS=n +CONFIG_DISABLE_MQUEUE=n +CONFIG_DISABLE_MOUNTPOINT=n +CONFIG_DISABLE_ENVIRON=n +CONFIG_DISABLE_POLL=y + +# +# Misc libc settings +# +# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a +# little smaller if we do not support fieldwidthes +# +CONFIG_NOPRINTF_FIELDWIDTH=n + +# +# Allow for architecture optimized implementations +# +# The architecture can provide optimized versions of the +# following to improve system performance +# +CONFIG_ARCH_MEMCPY=n +CONFIG_ARCH_MEMCMP=n +CONFIG_ARCH_MEMMOVE=n +CONFIG_ARCH_MEMSET=n +CONFIG_ARCH_STRCMP=n +CONFIG_ARCH_STRCPY=n +CONFIG_ARCH_STRNCPY=n +CONFIG_ARCH_STRLEN=n +CONFIG_ARCH_STRNLEN=n +CONFIG_ARCH_BZERO=n + +# +# Sizes of configurable things (0 disables) +# +# CONFIG_MAX_TASKS - The maximum number of simultaneously +# active tasks. This value must be a power of two. +# CONFIG_MAX_TASK_ARGS - This controls the maximum number of +# of parameters that a task may receive (i.e., maxmum value +# of 'argc') +# CONFIG_NPTHREAD_KEYS - The number of items of thread- +# specific data that can be retained +# CONFIG_NFILE_DESCRIPTORS - The maximum number of file +# descriptors (one for each open) +# CONFIG_NFILE_STREAMS - The maximum number of streams that +# can be fopen'ed +# CONFIG_NAME_MAX - The maximum size of a file name. +# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate +# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled +# (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added +# to force automatic, line-oriented flushing the output buffer +# for putc(), fputc(), putchar(), puts(), fputs(), printf(), +# fprintf(), and vfprintf(). When a newline is encountered in +# the output string, the output buffer will be flushed. This +# (slightly) increases the NuttX footprint but supports the kind +# of behavior that people expect for printf(). +# CONFIG_NUNGET_CHARS - Number of characters that can be +# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message +# structures. The system manages a pool of preallocated +# message structures to minimize dynamic allocations +# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with +# a fixed payload size given by this settin (does not include +# other message structure overhead. +# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that +# can be passed to a watchdog handler +# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog +# structures. The system manages a pool of preallocated +# watchdog structures to minimize dynamic allocations +# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX +# timer structures. The system manages a pool of preallocated +# timer structures to minimize dynamic allocations. Set to +# zero for all dynamic allocations. +# +CONFIG_MAX_TASKS=16 +CONFIG_MAX_TASK_ARGS=4 +CONFIG_NPTHREAD_KEYS=4 +CONFIG_NFILE_DESCRIPTORS=8 +CONFIG_NFILE_STREAMS=8 +CONFIG_NAME_MAX=32 +CONFIG_STDIO_BUFFER_SIZE=256 +CONFIG_STDIO_LINEBUFFER=y +CONFIG_NUNGET_CHARS=2 +CONFIG_PREALLOC_MQ_MSGS=4 +CONFIG_MQ_MAXMSGSIZE=32 +CONFIG_MAX_WDOGPARMS=2 +CONFIG_PREALLOC_WDOGS=8 +CONFIG_PREALLOC_TIMERS=4 + +# +# Framebuffer driver options +# +CONFIG_FB_CMAP=n +CONFIG_FB_HWCURSOR=n +CONFIG_FB_HWCURSORIMAGE=n +#CONFIG_FB_HWCURSORSIZE +#CONFIG_FB_TRANSPARENCY + +# +# Filesystem configuration +# +# CONFIG_FS_FAT - Enable FAT filesystem support +# CONFIG_FAT_SECTORSIZE - Max supported sector size +# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 +# file name support. +# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims +# patents on FAT long file name technology. Please read the +# disclaimer in the top-level COPYING file and only enable this +# feature if you understand these issues. +# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the +# default, maximum long file name is 255 bytes. This can eat up +# a lot of memory (especially stack space). If you are willing +# to live with some non-standard, short long file names, then +# define this value. A good choice would be the same value as +# selected for CONFIG_NAME_MAX which will limit the visibility +# of longer file names anyway. +# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. +# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. +# This must have one of the values of 0xff or 0x00. +# Default: 0xff. +# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, +# don't both with file chunks smaller than this number of data bytes. +# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. +# Default: 255. +# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, +# don't both with file chunks smaller than this number of data bytes. +# Default: 32. +# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean +# packing files together toward the end of the file or, if file are +# deleted at the end of the file, clean up can simply mean erasing +# the end of FLASH memory so that it can be re-used again. However, +# doing this can also harm the life of the FLASH part because it can +# mean that the tail end of the FLASH is re-used too often. This +# threshold determines if/when it is worth erased the tail end of FLASH +# and making it available for re-use (and possible over-wear). +# Default: 8192. +# CONFIG_FS_ROMFS - Enable ROMFS filesystem support +# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this +# option will enable a limited form of memory mapping that is +# implemented by copying whole files into memory. +# +CONFIG_FS_FAT=y +CONFIG_FAT_LCNAMES=y +CONFIG_FAT_LFN=y +CONFIG_FAT_MAXFNAME=32 +CONFIG_FS_NXFFS=n +CONFIG_FS_ROMFS=n + +# +# SPI-based MMC/SD driver +# +# CONFIG_MMCSD_NSLOTS +# Number of MMC/SD slots supported by the driver +# CONFIG_MMCSD_READONLY +# Provide read-only access (default is read/write) +# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. +# Default is 20MHz. +# +CONFIG_MMCSD_NSLOTS=1 +CONFIG_MMCSD_READONLY=n +CONFIG_MMCSD_SPICLOCK=12500000 + +# +# Block driver buffering +# +# CONFIG_FS_READAHEAD +# Enable read-ahead buffering +# CONFIG_FS_WRITEBUFFER +# Enable write buffering +# +CONFIG_FS_READAHEAD=n +CONFIG_FS_WRITEBUFFER=n + +# +# STM32 SDIO-based MMC/SD driver +# +# CONFIG_SDIO_DMA +# SDIO driver supports DMA +# CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128 +# CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority. +# Default: Medium +# CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default: +# 4-bit transfer mode. +# CONFIG_MMCSD_MMCSUPPORT +# Enable support for MMC cards +# CONFIG_MMCSD_HAVECARDDETECT +# SDIO driver card detection is 100% accurate +# +CONFIG_SDIO_DMA=n +#CONFIG_SDIO_PRI=128 +#CONFIG_SDIO_DMAPRIO +#CONFIG_SDIO_WIDTH_D1_ONLY +CONFIG_MMCSD_MMCSUPPORT=n +CONFIG_MMCSD_HAVECARDDETECT=n + +# +# SDIO-based MMC/SD driver +# +# CONFIG_SDIO_DMA +# SDIO driver supports DMA +# CONFIG_MMCSD_MMCSUPPORT +# Enable support for MMC cards +# CONFIG_MMCSD_HAVECARDDETECT +# SDIO driver card detection is 100% accurate +# +CONFIG_SDIO_DMA=n +CONFIG_MMCSD_MMCSUPPORT=n +CONFIG_MMCSD_HAVECARDDETECT=n + +# +# TCP/IP and UDP support via uIP +# +# CONFIG_NET - Enable or disable all network features +# CONFIG_NET_NOINTS - uIP not called from interrupt level. +# CONFIG_NET_MULTIBUFFER - Use multiple input/output buffers (probably no) +# CONFIG_NET_IPv6 - Build in support for IPv6 +# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. +# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options +# CONFIG_NET_BUFSIZE - uIP buffer size +# CONFIG_NET_TCP - TCP support on or off +# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) +# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers +# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) +# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until +# accept() is called. The size of the backlog is selected when listen() is called. +# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) +# CONFIG_NET_UDP - UDP support on or off +# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off +# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections +# CONFIG_NET_ICMP - ICMP ping response support on or off +# CONFIG_NET_ICMP_PING - ICMP ping request support on or off +# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address +# CONFIG_NET_STATISTICS - uIP statistics on or off +# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window +# CONFIG_NET_BROADCAST - Broadcast support +# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table +# CONFIG_NET_ARP_IPIN - Harvest IP/MAC address mappings from the ARP table +# from incoming IP packets. +# CONFIG_NET_MULTICAST - Outgoing multi-cast address support +# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when +# looking for duplicates +# +CONFIG_NET=y +CONFIG_NET_NOINTS=n +CONFIG_NET_MULTIBUFFER=y +CONFIG_NET_IPv6=n +CONFIG_NSOCKET_DESCRIPTORS=10 +CONFIG_NET_SOCKOPTS=y +CONFIG_NET_BUFSIZE=562 +CONFIG_NET_TCP=y +CONFIG_NET_TCP_CONNS=40 +#CONFIG_NET_TCP_READAHEAD_BUFSIZE +CONFIG_NET_NTCP_READAHEAD_BUFFERS=16 +CONFIG_NET_TCPBACKLOG=y +CONFIG_NET_MAX_LISTENPORTS=40 +CONFIG_NET_UDP=y +CONFIG_NET_UDP_CHECKSUMS=y +#CONFIG_NET_UDP_CONNS=10 +CONFIG_NET_ICMP=y +CONFIG_NET_ICMP_PING=y +#CONFIG_NET_PINGADDRCONF=0 +CONFIG_NET_STATISTICS=y +#CONFIG_NET_RECEIVE_WINDOW= +CONFIG_NET_BROADCAST=n +#CONFIG_NET_ARPTAB_SIZE=8 +CONFIG_NET_ARP_IPIN=n +CONFIG_NET_MULTICAST=n +#CONFIG_NET_FWCACHE_SIZE=2 + +# +# UIP Network Utilities +# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP +# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries +# +CONFIG_NET_DHCP_LIGHT=n +CONFIG_NET_RESOLV_ENTRIES=4 + +# +# FTP Server +# +# CONFIG_FTPD_VENDORID - The vendor name to use in FTP communications. +# Default: "NuttX" +# CONFIG_FTPD_SERVERID - The server name to use in FTP communications. +# Default: "NuttX FTP Server" +# CONFIG_FTPD_CMDBUFFERSIZE - The maximum size of one command. Default: +# 512 bytes. +# CONFIG_FTPD_DATABUFFERSIZE - The size of the I/O buffer for data +# transfers. Default: 2048 bytes. +# CONFIG_FTPD_WORKERSTACKSIZE - The stacksize to allocate for each +# FTP daemon worker thread. Default: 2048 bytes. +# +# Other required configuration settings: Of course TCP networking support +# is required. But here are a couple that are less obvious: +# +# CONFIG_DISABLE_PTHREAD - pthread support is required +# CONFIG_DISABLE_POLL - poll() support is required +# + +# +# RTC Configuration +# +# CONFIG_RTC - Enables general support for a hardware RTC. Specific +# architectures may require other specific settings. +# CONFIG_RTC_DATETIME - There are two general types of RTC: (1) A simple +# battery backed counter that keeps the time when power is down, and (2) +# A full date / time RTC the provides the date and time information, often +# in BCD format. If CONFIG_RTC_DATETIME is selected, it specifies this +# second kind of RTC. In this case, the RTC is used to "seed" the normal +# NuttX timer and the NuttX system timer provides for higher resoution +# time. +# CONFIG_RTC_HIRES - If CONFIG_RTC_DATETIME not selected, then the simple, +# battery backed counter is used. There are two different implementations +# of such simple counters based on the time resolution of the counter: +# The typical RTC keeps time to resolution of 1 second, usually +# supporting a 32-bit time_t value. In this case, the RTC is used to +# "seed" the normal NuttX timer and the NuttX timer provides for higher +# resoution time. If CONFIG_RTC_HIRES is enabled in the NuttX configuration, +# then the RTC provides higher resolution time and completely replaces the +# system timer for purpose of date and time. +# CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the frequency +# of the high resolution RTC must be provided. If CONFIG_RTC_HIRES is +# not defined, CONFIG_RTC_FREQUENCY is assumed to be one. +# CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an +# alarm. A callback function will be executed when the alarm goes off +# +CONFIG_RTC=y +CONFIG_RTC_DATETIME=y +CONFIG_RTC_HIRES=n +CONFIG_RTC_FREQUENCY=n +CONFIG_RTC_ALARM=n + +# +# USB Device Configuration +# +# CONFIG_USBDEV +# Enables USB device support +# CONFIG_USBDEV_ISOCHRONOUS +# Build in extra support for isochronous endpoints +# CONFIG_USBDEV_DUALSPEED +# Hardware handles high and full speed operation (USB 2.0) +# CONFIG_USBDEV_SELFPOWERED +# Will cause USB features to indicate that the device is +# self-powered +# CONFIG_USBDEV_MAXPOWER +# Maximum power consumption in mA +# CONFIG_USBDEV_TRACE +# Enables USB tracing for debug +# CONFIG_USBDEV_TRACE_NRECORDS +# Number of trace entries to remember +# +CONFIG_USBDEV=n +CONFIG_USBDEV_ISOCHRONOUS=n +CONFIG_USBDEV_DUALSPEED=n +CONFIG_USBDEV_SELFPOWERED=y +CONFIG_USBDEV_REMOTEWAKEUP=n +CONFIG_USBDEV_MAXPOWER=100 +CONFIG_USBDEV_TRACE=n +CONFIG_USBDEV_TRACE_NRECORDS=128 + +# +# USB Serial Device Configuration +# +# CONFIG_PL2303 +# Enable compilation of the USB serial driver +# CONFIG_PL2303_EPINTIN +# The logical 7-bit address of a hardware endpoint that supports +# interrupt IN operation +# CONFIG_PL2303_EPBULKOUT +# The logical 7-bit address of a hardware endpoint that supports +# bulk OUT operation +# CONFIG_PL2303_EPBULKIN +# The logical 7-bit address of a hardware endpoint that supports +# bulk IN operation +# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR +# The vendor ID code/string +# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR +# The product ID code/string +# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE +# Size of the serial receive/transmit buffers +# +CONFIG_PL2303=n +CONFIG_PL2303_EPINTIN=1 +CONFIG_PL2303_EPBULKOUT=2 +CONFIG_PL2303_EPBULKIN=3 +CONFIG_PL2303_NWRREQS=4 +CONFIG_PL2303_NRDREQS=4 +CONFIG_PL2303_VENDORID=0x067b +CONFIG_PL2303_PRODUCTID=0x2303 +CONFIG_PL2303_VENDORSTR="Nuttx" +CONFIG_PL2303_PRODUCTSTR="USBdev Serial" +CONFIG_PL2303_RXBUFSIZE=512 +CONFIG_PL2303_TXBUFSIZE=512 + +# +# USB Storage Device Configuration +# +# CONFIG_USBMSC +# Enable compilation of the USB storage driver +# CONFIG_USBMSC_EP0MAXPACKET +# Max packet size for endpoint 0 +# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN +# The logical 7-bit address of a hardware endpoints that support +# bulk OUT and IN operations +# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN +# The size of the buffer in each write/read request. This +# value needs to be at least as large as the endpoint +# maxpacket and ideally as large as a block device sector. +# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR +# The vendor ID code/string +# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR +# The product ID code/string +# CONFIG_USBMSC_REMOVABLE +# Select if the media is removable +# +CONFIG_USBMSC=n +CONFIG_USBMSC_EP0MAXPACKET=64 +CONFIG_USBMSC_EPBULKOUT=2 +CONFIG_USBMSC_EPBULKIN=5 +CONFIG_USBMSC_NRDREQS=2 +CONFIG_USBMSC_NWRREQS=2 +CONFIG_USBMSC_BULKINREQLEN=256 +CONFIG_USBMSC_BULKOUTREQLEN=256 +CONFIG_USBMSC_VENDORID=0x584e +CONFIG_USBMSC_VENDORSTR="NuttX" +CONFIG_USBMSC_PRODUCTID=0x5342 +CONFIG_USBMSC_PRODUCTSTR="USBdev Storage" +CONFIG_USBMSC_VERSIONNO=0x0399 +CONFIG_USBMSC_REMOVABLE=y + +# +# Graphics related configuration settings +# +# CONFIG_NX +# Enables overall support for graphics library and NX +# CONFIG_NX_MULTIUSER +# Configures NX in multi-user mode +# CONFIG_NX_NPLANES +# Some YUV color formats requires support for multiple planes, +# one for each color component. Unless you have such special +# hardware, this value should be undefined or set to 1 +# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP, +# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP, +# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and +# CONFIG_NX_DISABLE_32BPP +# NX supports a variety of pixel depths. You can save some +# memory by disabling support for unused color depths. +# CONFIG_NX_PACKEDMSFIRST +# If a pixel depth of less than 8-bits is used, then NX needs +# to know if the pixels pack from the MS to LS or from LS to MS +# CONFIG_NX_LCDDRIVER +# By default, NX builds to use a framebuffer driver (see +# include/nuttx/fb.h). If this option is defined, NX will +# build to use an LCD driver (see include/nuttx/lcd/lcd.h). +# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device. +# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device. +# CONFIG_NX_MOUSE +# Build in support for mouse input +# CONFIG_NX_KBD +# Build in support of keypad/keyboard input +# CONFIG_NXTK_BORDERWIDTH +# Specifies with with of the border (in pixels) used with +# framed windows. The default is 4. +# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2 +# Specify the colors of the border used with framed windows. +# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so +# is normally darker. The default is medium and dark grey, +# respectively +# CONFIG_NXTK_AUTORAISE +# If set, a window will be raised to the top if the mouse position +# is over a visible portion of the window. Default: A mouse +# button must be clicked over a visible portion of the window. +# CONFIG_NXFONTS_CHARBITS +# The number of bits in the character set. Current options are +# only 7 and 8. The default is 7. +# CONFIG_NXFONT_SANS17X22 +# This option enables support for a tiny, 17x22 san serif font +# (font ID FONTID_SANS17X22 == 14). +# CONFIG_NXFONT_SANS20X26 +# This option enables support for a tiny, 20x26 san serif font +# (font ID FONTID_SANS20X26 == 15). +# CONFIG_NXFONT_SANS23X27 +# This option enables support for a tiny, 23x27 san serif font +# (font ID FONTID_SANS23X27 == 1). +# CONFIG_NXFONT_SANS22X29 +# This option enables support for a small, 22x29 san serif font +# (font ID FONTID_SANS22X29 == 2). +# CONFIG_NXFONT_SANS28X37 +# This option enables support for a medium, 28x37 san serif font +# (font ID FONTID_SANS28X37 == 3). +# CONFIG_NXFONT_SANS39X48 +# This option enables support for a large, 39x48 san serif font +# (font ID FONTID_SANS39X48 == 4). +# CONFIG_NXFONT_SANS17X23B +# This option enables support for a tiny, 17x23 san serif bold font +# (font ID FONTID_SANS17X23B == 16). +# CONFIG_NXFONT_SANS20X27B +# This option enables support for a tiny, 20x27 san serif bold font +# (font ID FONTID_SANS20X27B == 17). +# CONFIG_NXFONT_SANS22X29B +# This option enables support for a small, 22x29 san serif bold font +# (font ID FONTID_SANS22X29B == 5). +# CONFIG_NXFONT_SANS28X37B +# This option enables support for a medium, 28x37 san serif bold font +# (font ID FONTID_SANS28X37B == 6). +# CONFIG_NXFONT_SANS40X49B +# This option enables support for a large, 40x49 san serif bold font +# (font ID FONTID_SANS40X49B == 7). +# CONFIG_NXFONT_SERIF22X29 +# This option enables support for a small, 22x29 font (with serifs) +# (font ID FONTID_SERIF22X29 == 8). +# CONFIG_NXFONT_SERIF29X37 +# This option enables support for a medium, 29x37 font (with serifs) +# (font ID FONTID_SERIF29X37 == 9). +# CONFIG_NXFONT_SERIF38X48 +# This option enables support for a large, 38x48 font (with serifs) +# (font ID FONTID_SERIF38X48 == 10). +# CONFIG_NXFONT_SERIF22X28B +# This option enables support for a small, 27x38 bold font (with serifs) +# (font ID FONTID_SERIF22X28B == 11). +# CONFIG_NXFONT_SERIF27X38B +# This option enables support for a medium, 27x38 bold font (with serifs) +# (font ID FONTID_SERIF27X38B == 12). +# CONFIG_NXFONT_SERIF38X49B +# This option enables support for a large, 38x49 bold font (with serifs) +# (font ID FONTID_SERIF38X49B == 13). +# +# NX Multi-user only options: +# +# CONFIG_NX_BLOCKING +# Open the client message queues in blocking mode. In this case, +# nx_eventhandler() will not return until a message is received and processed. +# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS +# Specifies the maximum number of messages that can fit in +# the message queues. No additional resources are allocated, but +# this can be set to prevent flooding of the client or server with +# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many +# messages are pre-allocated). +# +CONFIG_NX=n +CONFIG_NX_MULTIUSER=n +CONFIG_NX_NPLANES=1 +CONFIG_NX_DISABLE_1BPP=y +CONFIG_NX_DISABLE_2BPP=y +CONFIG_NX_DISABLE_4BPP=y +CONFIG_NX_DISABLE_8BPP=y +CONFIG_NX_DISABLE_16BPP=n +CONFIG_NX_DISABLE_24BPP=y +CONFIG_NX_DISABLE_32BPP=y +CONFIG_NX_PACKEDMSFIRST=n +CONFIG_NX_LCDDRIVER=y +CONFIG_LCD_MAXPOWER=1 +CONFIG_LCD_MAXCONTRAST=1 +CONFIG_NX_MOUSE=y +CONFIG_NX_KBD=y +#CONFIG_NXTK_BORDERWIDTH=4 +CONFIG_NXTK_BORDERCOLOR1=0xd69a +CONFIG_NXTK_BORDERCOLOR2=0xad55 +CONFIG_NXTK_AUTORAISE=n +CONFIG_NXFONT_SANS17X22=y +CONFIG_NXFONT_SANS20X26=n +CONFIG_NXFONT_SANS22X29=n +CONFIG_NXFONT_SANS23X27=n +CONFIG_NXFONT_SANS28X37=n +CONFIG_NXFONT_SANS17X23B=n +CONFIG_NXFONT_SANS20X27B=y +CONFIG_NXFONT_SANS22X29B=y +CONFIG_NXFONT_SANS28X37B=n +CONFIG_NXFONT_SANS40X49B=n +CONFIG_NXFONT_SERIF22X29=n +CONFIG_NXFONT_SERIF29X37=n +CONFIG_NXFONT_SERIF38X48=n +CONFIG_NXFONT_SERIF22X28B=n +CONFIG_NXFONT_SERIF27X38B=n +CONFIG_NXFONT_SERIF38X49B=n +CONFIG_NXFONTS_CHARBITS=7 +CONFIG_NX_BLOCKING=y +CONFIG_NX_MXSERVERMSGS=32 +CONFIG_NX_MXCLIENTMSGS=16 + +# +# Settings for examples/uip +# +CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_EXAMPLE_UIP_DHCPC=n + +# +# Settings for examples/nettest +CONFIG_EXAMPLE_NETTEST_SERVER=n +CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n +CONFIG_EXAMPLE_NETTEST_NOMAC=y +CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1) + +# +# Settings for examples/ostest +# +CONFIG_EXAMPLES_OSTEST_LOOPS=1 +CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048 +CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 + +# +# Settings for apps/nshlib +# +# CONFIG_NSH_BUILTIN_APPS - Support external registered, +# "named" applications that can be executed from the NSH +# command line (see apps/README.txt for more information). +# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer +# CONFIG_NSH_STRERROR - Use strerror(errno) +# CONFIG_NSH_LINELEN - Maximum length of one command line +# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi +# CONFIG_NSH_DISABLESCRIPT - Disable scripting support +# CONFIG_NSH_DISABLEBG - Disable background commands +# CONFIG_NSH_ROMFSETC - Use startup script in /etc +# CONFIG_NSH_CONSOLE - Use serial console front end +# CONFIG_NSH_TELNET - Use telnetd console front end +# CONFIG_NSH_ARCHINIT - Platform provides architecture +# specific initialization (nsh_archinitialize()). +# +# If CONFIG_NSH_TELNET is selected: +# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size +# CONFIG_NSH_DHCPC - Obtain address using DHCP +# CONFIG_NSH_IPADDR - Provides static IP address +# CONFIG_NSH_DRIPADDR - Provides static router IP address +# CONFIG_NSH_NETMASK - Provides static network mask +# CONFIG_NSH_NOMAC - Use a bogus MAC address +# +# If CONFIG_NSH_ROMFSETC is selected: +# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint +# CONFIG_NSH_INITSCRIPT - Relative path to init script +# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor +# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size +# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor +# CONFIG_NSH_FATSECTSIZE - FAT FS sector size +# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors +# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint +# +CONFIG_NSH_BUILTIN_APPS=y +CONFIG_NSH_FILEIOSIZE=512 +CONFIG_NSH_STRERROR=n +CONFIG_NSH_LINELEN=64 +CONFIG_NSH_NESTDEPTH=3 +CONFIG_NSH_DISABLESCRIPT=n +CONFIG_NSH_DISABLEBG=n +CONFIG_NSH_ROMFSETC=n +CONFIG_NSH_CONSOLE=y +CONFIG_NSH_TELNET=y +CONFIG_NSH_ARCHINIT=n +CONFIG_NSH_IOBUFFER_SIZE=512 +CONFIG_NSH_DHCPC=n +CONFIG_NSH_NOMAC=y +CONFIG_NSH_IPADDR=(192<<24|168<<16|13<<8|161) +CONFIG_NSH_DRIPADDR=(192<<24|168<<16|13<<8|1) +CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_NSH_ROMFSMOUNTPT="/etc" +CONFIG_NSH_INITSCRIPT="init.d/rcS" +CONFIG_NSH_ROMFSDEVNO=0 +CONFIG_NSH_ROMFSSECTSIZE=64 +CONFIG_NSH_FATDEVNO=1 +CONFIG_NSH_FATSECTSIZE=512 +CONFIG_NSH_FATNSECTORS=1024 +CONFIG_NSH_FATMOUNTPT=/tmp + +# +# Architecture-specific NSH options +# +CONFIG_NSH_MMCSDSPIPORTNO=0 +CONFIG_NSH_MMCSDSLOTNO=0 +CONFIG_NSH_MMCSDMINOR=0 + +# +# I2C tool settings +# +# CONFIG_I2CTOOL_BUILTIN - Build the tools as an NSH built-in command +# CONFIG_I2CTOOL_MINBUS - Smallest bus index supported by the hardware (default 0). +# CONFIG_I2CTOOL_MAXBUS - Largest bus index supported by the hardware (default 3) +# CONFIG_I2CTOOL_MINADDR - Minium device address (default: 0x03) +# CONFIG_I2CTOOL_MAXADDR - Largest device address (default: 0x77) +# CONFIG_I2CTOOL_MAXREGADDR - Largest register address (default: 0xff) +# CONFIG_I2CTOOL_DEFFREQ - Default frequency (default: 1000000) +# +CONFIG_I2CTOOL_BUILTIN=y +CONFIG_I2CTOOL_MINBUS=1 +CONFIG_I2CTOOL_MAXBUS=3 +#CONFIG_I2CTOOL_MINADDR +#CONFIG_I2CTOOL_MAXADDR +#CONFIG_I2CTOOL_MAXREGADDR +CONFIG_I2CTOOL_DEFFREQ=100000 + +# +# Settings for examples/usbserial +# +# CONFIG_EXAMPLES_USBSERIAL_INONLY +# Only verify IN (device-to-host) data transfers. Default: both +# CONFIG_EXAMPLES_USBSERIAL_OUTONLY +# Only verify OUT (host-to-device) data transfers. Default: both +# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL +# Send only small, single packet messages. Default: Send large and small. +# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG +# Send only large, multi-packet messages. Default: Send large and small. +# +CONFIG_EXAMPLES_USBSERIAL_INONLY=n +CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n +CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n +CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n + +CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n +CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n +CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n +CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n +CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n + +# +# Settings for examples/adc +# +# CONFIG_ADC - Enabled ADC support +# CONFIG_NSH_BUILTIN_APPS - Build the ADC test as an NSH built-in function. +# Default: Built as a standalone problem +# +# CONFIG_EXAMPLES_ADC_DEVPATH - The path to the ADC device. Default: /dev/adc0 +# CONFIG_EXAMPLES_ADC_NSAMPLES - If CONFIG_NSH_BUILTIN_APPS +# is defined, then the number of samples is provided on the command line +# and this value is ignored. Otherwise, this number of samples is +# collected and the program terminates. Default: Samples are collected +# indefinitely. +# CONFIG_EXAMPLES_ADC_GROUPSIZE - The number of samples to read at once. +# Default: 4 + +# +# Settings for examples/can +# +# CONFIG_CAN - Enables CAN support. +# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback +# mode for testing. The STM32 CAN driver does support loopback mode. +# CONFIG_NSH_BUILTIN_APPS - Build the CAN test as an NSH built-in function. +# Default: Built as a standalone problem +# +# CONFIG_EXAMPLES_CAN_DEVPATH - The path to the CAN device. Default: /dev/can0 +# CONFIG_EXAMPLES_CAN_NMSGS - If CONFIG_NSH_BUILTIN_APPS +# is defined, then the number of loops is provided on the command line +# and this value is ignored. Otherwise, this number of CAN message is +# collected and the program terminates. Default: If built as an NSH +# built-in, the default is 32. Otherwise messages are sent and received +# indefinitely. + +# +# Settings for examples/pwm +# +# CONFIG_PWM - Enables PWM support. +# CONFIG_NSH_BUILTIN_APPS - Build the PWM test as an NSH built-in function. +# Default: Not built! The example can only be used as an NSH built-in +# application +# +# CONFIG_EXAMPLES_PWM_DEVPATH - The path to the PWM device. Default: /dev/pwm0 +# CONFIG_EXAMPLES_PWM_FREQUENCY - The initial PWM frequency. Default: 100 Hz +# CONFIG_EXAMPLES_PWM_DUTYPCT - The initial PWM duty as a percentage. Default: 50% +# CONFIG_EXAMPLES_PWM_DURATION - The initial PWM pulse train duration in sectonds. +# as a percentage. Default: 5 seconds + +# +# Settings for examples/ftpd +# +# CONFIG_EXAMPLES_FTPD_PRIO - Priority of the FTP daemon. +# Default: SCHED_PRIORITY_DEFAULT +# CONFIG_EXAMPLES_FTPD_STACKSIZE - Stack size allocated for the +# FTP daemon. Default: 2048 +# CONFIG_EXAMPLES_FTPD_NONETINIT - Define to suppress configuration of the +# network by apps/examples/ftpd. You would need to suppress network +# configuration if the network is configuration prior to running the +# example. +# +# NSH always initializes the network so if CONFIG_NSH_BUILTIN_APPS is +# defined, so is CONFIG_EXAMPLES_FTPD_NONETINIT (se it does not explicitly +# need to be defined in that case): +# +# CONFIG_NSH_BUILTIN_APPS - Build the FTPD daemon example test as an +# NSH built-in function. By default the FTPD daemon will be built +# as a standalone application. +# +# If CONFIG_EXAMPLES_FTPD_NONETINIT is not defined, then the following may +# be specified to customized the network configuration: +# +# CONFIG_EXAMPLE_FTPD_NOMAC - If the hardware has no MAC address of its +# own, define this =y to provide a bogus address for testing. +# CONFIG_EXAMPLE_FTPD_IPADDR - The target IP address. Default 10.0.0.2 +# CONFIG_EXAMPLE_FTPD_DRIPADDR - The default router address. Default +# 10.0.0.1 +# CONFIG_EXAMPLE_FTPD_NETMASK - The network mask. Default: 255.255.255.0 + +# +# Stack and heap information +# +# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP +# operation from FLASH but must copy initialized .data sections to RAM. +# (should also be =n for the STM3220G-EVAL which always runs from flash) +# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH +# but copy themselves entirely into RAM for better performance. +# CONFIG_CUSTOM_STACK - The up_ implementation will handle +# all stack operations outside of the nuttx model. +# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) +# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. +# This is the thread that (1) performs the inital boot of the system up +# to the point where user_start() is spawned, and (2) there after is the +# IDLE thread that executes only when there is no other thread ready to +# run. +# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate +# for the main user thread that begins at the user_start() entry point. +# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size +# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size +# CONFIG_HEAP_BASE - The beginning of the heap +# CONFIG_HEAP_SIZE - The size of the heap +# +CONFIG_BOOT_RUNFROMFLASH=n +CONFIG_BOOT_COPYTORAM=n +CONFIG_CUSTOM_STACK=n +CONFIG_STACK_POINTER= +CONFIG_IDLETHREAD_STACKSIZE=1024 +CONFIG_USERMAIN_STACKSIZE=2048 +CONFIG_PTHREAD_STACK_MIN=256 +CONFIG_PTHREAD_STACK_DEFAULT=2048 +CONFIG_HEAP_BASE= +CONFIG_HEAP_SIZE= |