diff options
Diffstat (limited to 'nuttx/configs')
-rw-r--r-- | nuttx/configs/open1788/README.txt | 6 | ||||
-rw-r--r-- | nuttx/configs/open1788/include/board.h | 6 | ||||
-rw-r--r-- | nuttx/configs/open1788/src/lpc17_ssp.c | 2 | ||||
-rw-r--r-- | nuttx/configs/open1788/src/lpc17_touchscreen.c | 97 |
4 files changed, 73 insertions, 38 deletions
diff --git a/nuttx/configs/open1788/README.txt b/nuttx/configs/open1788/README.txt index 61a01c3a7..1c3a5191e 100644 --- a/nuttx/configs/open1788/README.txt +++ b/nuttx/configs/open1788/README.txt @@ -453,10 +453,11 @@ CONFIGURATION following ways: CONFIG_INPUT=y : Enable support for input devices - CONFIG_GPIO_IRQ=y : GPIO interrupt support CONFIG_INPUT_ADS7843E=y : Enable support for the XPT2048 + CONFIG_ADS7843E_SPIDEV=1 : Use SSP1 for communication CONFIG_SPI=y : Enable SPI support CONFIG_SPI_EXCHANGE=n : exchange() method is not supported + CONFIG_GPIO_IRQ=y : GPIO interrupt support CONFIG_LPC17_SSP1=y : Enable support for SSP1 CONFIG_EXAMPLES_TOUCHSCREEN=y : Enable the touchscreen built-int test CONFIG_EXAMPLES_TOUCHSCREEN_BUILTIN=y @@ -466,7 +467,8 @@ CONFIGURATION You will also have to disable SD card support to use this test. The SD card detect (CD) signal is on P0[13]. This signal is shared. It is also used for MOSI1 and USB_UP_LED. The CD pin may be disconnected. - There is a jumper on board that enables the CD pin. + There is a jumper on board that enables the CD pin. OR, you can simply + remove the SD module so that it does not drive the CD pin. CONFIG_LPC17_GPDMA=n : No DMA CONFIG_ARCH_DMA=n diff --git a/nuttx/configs/open1788/include/board.h b/nuttx/configs/open1788/include/board.h index 421476cab..ffcdf7211 100644 --- a/nuttx/configs/open1788/include/board.h +++ b/nuttx/configs/open1788/include/board.h @@ -407,12 +407,6 @@ #define GPIO_SSP1_MOSI GPIO_SSP1_MOSI_2 #define GPIO_SSP1_SCK GPIO_SSP1_SCK_2 -#define GPIO_SSP1_SSEL_1 (GPIO_ALT2 | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN6) -#define GPIO_SSP1_SSEL_2 (GPIO_ALT2 | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN14) -#define GPIO_SSP1_SSEL_3 (GPIO_ALT5 | GPIO_PULLUP | GPIO_PORT1 | GPIO_PIN26) -#define GPIO_SSP1_SSEL_4 (GPIO_ALT3 | GPIO_PULLUP | GPIO_PORT4 | GPIO_PIN21) - - /************************************************************************************ * Public Types ************************************************************************************/ diff --git a/nuttx/configs/open1788/src/lpc17_ssp.c b/nuttx/configs/open1788/src/lpc17_ssp.c index e27894e72..4f3995243 100644 --- a/nuttx/configs/open1788/src/lpc17_ssp.c +++ b/nuttx/configs/open1788/src/lpc17_ssp.c @@ -174,7 +174,7 @@ void lpc17_ssp1select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool sel sspdbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert"); if (devid == SPIDEV_TOUCHSCREEN) { - /* Assert/de-assert the CS pin to the card */ + /* Assert/de-assert the CS pin to the touchscreen */ ssp_dumpgpio(GPIO_TC_CS, "lpc17_ssp1select() Entry"); lpc17_gpiowrite(GPIO_TC_CS, !selected); diff --git a/nuttx/configs/open1788/src/lpc17_touchscreen.c b/nuttx/configs/open1788/src/lpc17_touchscreen.c index 1ee8d6237..19b8b5805 100644 --- a/nuttx/configs/open1788/src/lpc17_touchscreen.c +++ b/nuttx/configs/open1788/src/lpc17_touchscreen.c @@ -80,17 +80,27 @@ #endif #ifndef CONFIG_ADS7843E_SPIDEV -# define CONFIG_ADS7843E_SPIDEV 3 +# define CONFIG_ADS7843E_SPIDEV 1 #endif -#if CONFIG_ADS7843E_SPIDEV != 3 -# error "CONFIG_ADS7843E_SPIDEV must be three" +#if CONFIG_ADS7843E_SPIDEV != 1 +# error "CONFIG_ADS7843E_SPIDEV must be one" #endif #ifndef CONFIG_ADS7843E_DEVMINOR # define CONFIG_ADS7843E_DEVMINOR 0 #endif +/* REVISIT: Currently, XPT2046 reports BUSY all of the time. This is + * probably GPIO setting issues. But there is this cryptic statement in + * the XPT2046 spec: "No DCLK delay required with dedicated serial port." + * + * The busy state is used by the XPT2046 driver to control the delay + * between sending the command, then reading the returned data. + */ + +#define XPT2046_NO_BUSY 1 + /**************************************************************************** * Private Types ****************************************************************************/ @@ -100,12 +110,12 @@ ****************************************************************************/ /* IRQ/GPIO access callbacks. These operations all hidden behind - * callbacks to isolate the ADS7843E driver from differences in GPIO + * callbacks to isolate the XPT2046 driver from differences in GPIO * interrupt handling by varying boards and MCUs. If possible, * interrupts should be configured on both rising and falling edges * so that contact and loss-of-contact events can be detected. * - * attach - Attach the ADS7843E interrupt handler to the GPIO interrupt + * attach - Attach the XPT2046 interrupt handler to the GPIO interrupt * enable - Enable or disable the GPIO interrupt * clear - Acknowledge/clear any pending GPIO interrupt * pendown - Return the state of the pen down GPIO input @@ -121,9 +131,9 @@ static bool tsc_pendown(FAR struct ads7843e_config_s *state); * Private Data ****************************************************************************/ -/* A reference to a structure of this type must be passed to the ADS7843E +/* A reference to a structure of this type must be passed to the XPT2046 * driver. This structure provides information about the configuration - * of the ADS7843E and provides some board-specific hooks. + * of the XPT2046 and provides some board-specific hooks. * * Memory for this structure is provided by the caller. It is not copied * by the driver and is presumed to persist while the driver is active. @@ -144,12 +154,12 @@ static struct ads7843e_config_s g_tscinfo = ****************************************************************************/ /* IRQ/GPIO access callbacks. These operations all hidden behind - * callbacks to isolate the ADS7843E driver from differences in GPIO + * callbacks to isolate the XPT2046 driver from differences in GPIO * interrupt handling by varying boards and MCUs. If possible, * interrupts should be configured on both rising and falling edges * so that contact and loss-of-contact events can be detected. * - * attach - Attach the ADS7843E interrupt handler to the GPIO interrupt + * attach - Attach the XPT2046 interrupt handler to the GPIO interrupt * enable - Enable or disable the GPIO interrupt * clear - Acknowledge/clear any pending GPIO interrupt * pendown - Return the state of the pen down GPIO input @@ -183,6 +193,20 @@ static void tsc_clear(FAR struct ads7843e_config_s *state) static bool tsc_busy(FAR struct ads7843e_config_s *state) { +/* The busy state is used by the XPT2046 driver to control the delay + * between sending the command, then reading the returned data. + */ + +#ifdef XPT2046_NO_BUSY +/* REVISIT: Currently, XPT2046 reports BUSY all of the time. This is + * probably GPIO setting issues. But there is this cryptic statement in + * the XPT2046 spec: "No DCLK delay required with dedicated serial port." + */ + + return false; + +#else /* XPT2046_NO_BUSY */ + #if defined(CONFIG_DEBUG_INPUT) && defined(CONFIG_DEBUG_VERBOSE) static bool last = (bool)-1; #endif @@ -199,6 +223,8 @@ static bool tsc_busy(FAR struct ads7843e_config_s *state) #endif return busy; + +#endif /* XPT2046_NO_BUSY */ } static bool tsc_pendown(FAR struct ads7843e_config_s *state) @@ -237,37 +263,50 @@ static bool tsc_pendown(FAR struct ads7843e_config_s *state) int arch_tcinitialize(int minor) { + static bool initialized = false; FAR struct spi_dev_s *dev; int ret; - idbg("minor %d\n", minor); + idbg("initialized:%d minor:%d\n", initialized, minor); DEBUGASSERT(minor == 0); - /* Configure and enable the ADS7843E PENIRQ pin as an interrupting input. */ + /* Since there is no uninitialized logic, this initialization can be + * performed only one time. + */ - (void)lpc17_configgpio(GPIO_TC_PENIRQ); + if (!initialized) + { + /* Configure and enable the XPT2046 PENIRQ pin as an interrupting input. */ - /* Configure the ADS7843E BUSY pin as a normal input. */ + (void)lpc17_configgpio(GPIO_TC_PENIRQ); - (void)lpc17_configgpio(GPIO_TC_BUSY); + /* Configure the XPT2046 BUSY pin as a normal input. */ - /* Get an instance of the SPI interface */ +#ifndef XPT2046_NO_BUSY + (void)lpc17_configgpio(GPIO_TC_BUSY); +#endif - dev = lpc17_sspinitialize(CONFIG_ADS7843E_SPIDEV); - if (!dev) - { - idbg("Failed to initialize SPI bus %d\n", CONFIG_ADS7843E_SPIDEV); - return -ENODEV; - } + /* Get an instance of the SPI interface */ - /* Initialize and register the SPI touschscreen device */ + dev = lpc17_sspinitialize(CONFIG_ADS7843E_SPIDEV); + if (!dev) + { + idbg("Failed to initialize SPI bus %d\n", CONFIG_ADS7843E_SPIDEV); + return -ENODEV; + } - ret = ads7843e_register(dev, &g_tscinfo, CONFIG_ADS7843E_DEVMINOR); - if (ret < 0) - { - idbg("Failed to initialize SPI bus %d\n", CONFIG_ADS7843E_SPIDEV); - /* up_spiuninitialize(dev); */ - return -ENODEV; + /* Initialize and register the SPI touchscreen device */ + + ret = ads7843e_register(dev, &g_tscinfo, CONFIG_ADS7843E_DEVMINOR); + if (ret < 0) + { + idbg("Failed to register touchscreen device minor=%d\n", + CONFIG_ADS7843E_DEVMINOR); + /* up_spiuninitialize(dev); */ + return -ENODEV; + } + + initialized = true; } return OK; @@ -291,7 +330,7 @@ int arch_tcinitialize(int minor) void arch_tcuninitialize(void) { - /* No support for un-initializing the touchscreen ADS7843E device yet */ + /* No support for un-initializing the touchscreen XPT2046 device yet */ } #endif /* CONFIG_INPUT_ADS7843E */ |