diff options
Diffstat (limited to 'nuttx/configs')
-rw-r--r-- | nuttx/configs/sure-pic32mx/README.txt | 100 | ||||
-rw-r--r-- | nuttx/configs/sure-pic32mx/include/board.h | 13 | ||||
-rw-r--r-- | nuttx/configs/sure-pic32mx/src/Makefile | 5 | ||||
-rw-r--r-- | nuttx/configs/sure-pic32mx/src/up_buttons.c | 21 | ||||
-rw-r--r-- | nuttx/configs/sure-pic32mx/src/up_spi.c | 100 | ||||
-rw-r--r-- | nuttx/configs/sure-pic32mx/src/up_usbdev.c | 15 |
6 files changed, 229 insertions, 25 deletions
diff --git a/nuttx/configs/sure-pic32mx/README.txt b/nuttx/configs/sure-pic32mx/README.txt index e21325984..c7ba540bb 100644 --- a/nuttx/configs/sure-pic32mx/README.txt +++ b/nuttx/configs/sure-pic32mx/README.txt @@ -42,7 +42,10 @@ Contents PIC32MX440F512H Pin Out ======================= - PIC32MX440F512H 64-Pin QFN (USB) Pin Out. + DB_DP11215 PIC32 Storage Demo Board + ----------------------------------- + PIC32MX440F512H 64-Pin QFN (USB) Pin Out as used on the DB_DP11215 PIC32 Storage + Demo Board. LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left) PIN NAME SIGNAL NOTES @@ -65,7 +68,8 @@ PIC32MX440F512H Pin Out RB1 16 PGED1/AN0/VREF+/CVREF+/PMA6/ N/C Not connected CN2/RB0 - *FLASH (U1, SOIOC) not populated + + *FLASH (U1, SOIC) not populated BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left) PIN NAME SIGNAL NOTES @@ -88,7 +92,7 @@ PIC32MX440F512H Pin Out 31 SDA2/U2RX/PMA9/CN17/RF4 RXD2_MCU J5 DB9 via RS232 driver 32 SCL2/U2TX/PMA8/CN18/RF5 TXD2_MCU J5 DB9 via RS232 driver - *FLASH (U1, SOIOC) not populated + *FLASH (U1, SOIC) not populated RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left) PIN NAME SIGNAL NOTES @@ -133,6 +137,96 @@ PIC32MX440F512H Pin Out *USB-to-UART bridge (U1, CP2102) not populated + DB-DP11212 PIC32 General Purpose Demo Board + ------------------------------------------- + PIC32MX440F512H 64-Pin QFN (USB) Pin Out as used on the DB-DP11212 PIC32 General + Purpose Demo Board + + LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left) + PIN NAME SIGNAL NOTES + ---- ----------------------------- -------------- ------------------------------- + 1 PMD5/RE5 PMPD5 Display, JP1-12, DB5 + 2 PMD6/RE6 PMPD6 Display, JP1-13, DB6 + 3 PMD7/RE7 PMPD7 Display, JP1-14, DB7 + 4 SCK2/PMA5/CN8/RG6 SCK FLASH (U4) SCK* + 5 SDI2/PMA4/CN9/RG7 SDI FLASH (U4) SO* + 6 SDO2/PMA3/CN10/RG8 SDO FLASH (U4) SI* + 7 MCLR\ PIC_MCLR Pulled high, J2-1, ICSP + 8 SS2/PMA2/CN11/RG9 N/C Not connected + 9 Vss Grounded + 10 Vdd +3.3V --- + 11 Vbuson/AN5/CN7/RB5 RB5 LCD SEG5 (F), U5-10 + 12 AN4/CN6/RB4 RB4 LCD SEG4 (E), U5-1 + 13 AN3/CN5/RB3 RB3 LCD SEG3 (D), U5-2 + 14 AN2/CN4/RB2 RB2 LCD SEG2 (C), U5-4 + 15 PGEC1/AN1/Vref-/CN3/RB1 RB1 LCD SEG1 (B), U5-7 + 16 PGED1/AN0/VREF+/CVREF+/PMA6/ RB0 LCD SEG0 (A), U5-11 + CN2/RB0 + + *FLASH (U4, SOIC) not populated + + BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left) + PIN NAME SIGNAL NOTES + ---- ----------------------------- -------------- ------------------------------- + 17 PGEC2/AN6/OCFA/RB6 PIC_PGC2 J2-5, ICSP + 18 PGED2/AN7/RB7 PIC_PGD2 J2-4, ICSP + 19 AVdd +3.3V --- + 20 AVss Grounded + 21 AN8/U2CTS/RB8 RB8 LCD SEG6 (G), U5-5 + 22 AN9/PMA7/RB9 RB9 LCD SEG7 (DP), U5-3 + 23 TMS/AN10/PMA13/RB10 UTIL_WP FLASH (U4) WP* + 24 TDO/AN11/PMA12/RB11 UTIL_CS FLASH (U4) CS* + 25 Vss Grounded + 26 Vdd +3.3V --- + 27 TCK/AN12/PMA11/RB12 N/C Not connected + 28 TDI/AN13/PMA10/RB13 N/C Not connected + 29 AN14/U2RTS/PMA1/RB14 temp_AD temp_AD + 30 AN15/PMA0/CN12/RB15 PMPA0 Display, JP1-4, RS + 31 SDA2/U2RX/PMA9/CN17/RF4 SDA LM75/SO, U3-1, SDA + 32 SCL2/U2TX/PMA8/CN18/RF5 SCL LM75/SO, U3-2, SCL + + *FLASH (U4, SOIC) not populated + + RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left) + PIN NAME SIGNAL NOTES + ---- ----------------------------- -------------- ------------------------------- + 48 SOSCO/T1CK/CN0/RC14 SOSCO 32.768KHz XTAL (Y1) + 47 SOSCI/CN1/RC13 SOSCI 32.768KHz XTAL (Y1) + 46 OC1/INT0/RD0 RD0 LCD DIG1, U5-12 + 45 IC4/PMCS1/PMA14/RD11 PMCS1 Display, JP1-6, E + 44 SCL1/PMCS2/PMA15 RD10 LCD DIG2, U5-9 + 43 SDA1/RD9 RD9 LCD DIG3, U5-8 + 42 RTCC/RD8 RD8 LCD DIG4, U5-6 + 41 Vss Grounded + 40 OSC2/CLKO/RC15 OSC2 20MHz XTAL (Y2) + 39 OSC1/CLKI/RC12 OSC1 20MHz XTAL (Y2) + 38 Vdd +3.3V --- + 37 D+ MCU_D+ USB connectors via PHY + 36 D- MCU_D- USB connectors via PHY + 35 Vusb +3.3V --- + 34 Vbus +5V_DUSB Display, USB Mini-B, USB Type A, JP1-1, +5V + 33 USBID/RF3 N/C Not connected + + TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left) + PIN NAME SIGNAL NOTES + ---- ----------------------------- -------------- ------------------------------- + 64 PMPD4/RD4 PMPD4 Display, JP1-11, DB4 + 63 PMPD3/RD3 PMPD3 Display, JP1-10, DB3 + 62 PMPD2/RD2 PMPD2 Display, JP1-9, DB2 + 61 PMPD1/RD1 PMPD1 Display, JP1-8, DB1 + 60 PMPD0/RE0 PMPD0 Display, JP1-7, DB0 + 59 RF1 Key3 SW3-1 + 58 RF0 Key2 SW2-1 + 57 ENVREG ENVREG Pulled high + 56 Vcap/Vddcore VDDCORE Capacitors to ground + 55 CN16/RD7 N/C Not connected + 54 CN15/RD6 Key5 SW5-1 + 53 PMRD/CN14/RD5 PMPRD --- + 52 OC5/PMWR/CN13/RD4 PWM2 Used to control backlight level (Vo) + 51 U1TX/OC4/RD3 N/C Not connected + 50 U1RX/OC3/RD2 N/C Not connected + 49 OC2/RD1 PWM1 Used to control backlight level (K) + Toolchains ========== diff --git a/nuttx/configs/sure-pic32mx/include/board.h b/nuttx/configs/sure-pic32mx/include/board.h index 44eff5b62..66ed642c6 100644 --- a/nuttx/configs/sure-pic32mx/include/board.h +++ b/nuttx/configs/sure-pic32mx/include/board.h @@ -2,7 +2,7 @@ * configs/sure-pic32mx/include/board.h * include/arch/board/board.h * - * Copyright (C) 2011 Gregory Nutt. All rights reserved. + * Copyright (C) 2011-2012 Gregory Nutt. All rights reserved. * Author: Gregory Nutt <gnutt@nuttx.org> * * Redistribution and use in source and binary forms, with or without @@ -91,8 +91,9 @@ #undef BOARD_TIMER1_SOSC /* LED definitions **********************************************************/ -/* The Sure PIC32MX board has five LEDs. One (D4, lablel "Power") is not - * controllable by software. Four are controllable by software: +/* The Sure DB_DP11215 PIC32 Storage Demo Board board has five LEDs. One + * (D4, lablel "Power") is not controllable by software. Four are + * controllable by software: * * D7 "USB" Yellow RD7 Low illuminates * D8 "SD" Yellow RD6 Low illuminates @@ -111,6 +112,12 @@ #define LED_PANIC 5 /* N/C N/C N/C ON N/C N/C N/C OFF */ #define LED_NVALUES 6 +/* The Sure DB-DP11212 PIC32 General Purpose Demo Board does not have any user + * controllable LEDs, but does does have a segment LED display. That display is + * however, obscured by the larger segment display attached to the board and, so, + * is not supported. + */ + /* For distinguishing individual LEDs */ #define LED_USB 0 diff --git a/nuttx/configs/sure-pic32mx/src/Makefile b/nuttx/configs/sure-pic32mx/src/Makefile index f934ae35a..f5f9a89ea 100644 --- a/nuttx/configs/sure-pic32mx/src/Makefile +++ b/nuttx/configs/sure-pic32mx/src/Makefile @@ -40,9 +40,14 @@ CFLAGS += -I$(TOPDIR)/sched ASRCS = CSRCS = up_boot.c up_spi.c +# Only the DB_DP11215 PIC32 Storage Demo Board board has user controllable +# LEDs + +ifeq ($(CONFIG_ARCH_DBDP11215),y) ifeq ($(CONFIG_ARCH_LEDS),y) CSRCS += up_leds.c endif +endif ifeq ($(CONFIG_ARCH_BUTTONS),y) CSRCS += up_buttons.c diff --git a/nuttx/configs/sure-pic32mx/src/up_buttons.c b/nuttx/configs/sure-pic32mx/src/up_buttons.c index 9fccedfc1..80fb35fdb 100644 --- a/nuttx/configs/sure-pic32mx/src/up_buttons.c +++ b/nuttx/configs/sure-pic32mx/src/up_buttons.c @@ -58,20 +58,33 @@ /**************************************************************************** * Definitions ****************************************************************************/ -/* The Sure PIC32MX board has three buttons. +/* The Sure DB_DP11215 PIC32 Storage Demo Board has three buttons. * * SW1 (SW_UP, left arrow) RB3 Pulled high, Grounded/low when depressed * SW2 (SW_DOWN, down/right arrow) RB2 Pulled high, Grounded/low when depressed * SW3 (SW_OK, right arrow) RB4 Pulled high, Grounded/low when depressed * + * The Sure DB-DP11212 PIC32 General Purpose Demo Board also has three buttons, + * but these are connected differently: + * + * SW2-1 RF0 Pulled high, Grounded/low when depressed + * SW3-1 RF1 Pulled high, Grounded/low when depressed + * SW5-1 RD6 Pulled high, Grounded/low when depressed + * * Internal pull-ups are not required since the LEDs are pull-up externally. * Change notification interrupts are not *automatically* enabled. Change * notification will be enabled when pic32mx_gpioattach() is called. */ -#define GPIO_SW1 (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN3) -#define GPIO_SW2 (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN2) -#define GPIO_SW3 (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN4) +#ifdef CONFIG_ARCH_DBDP11215 +# define GPIO_SW1 (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN3) +# define GPIO_SW2 (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN2) +# define GPIO_SW3 (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN4) +#else /* CONFIG_ARCH_DBDP11212 */ +# define GPIO_SW1 (GPIO_INPUT|GPIO_INT|GPIO_PORTF|GPIO_PIN0) +# define GPIO_SW2 (GPIO_INPUT|GPIO_INT|GPIO_PORTF|GPIO_PIN1) +# define GPIO_SW3 (GPIO_INPUT|GPIO_INT|GPIO_PORTD|GPIO_PIN6) +#endif /* Change notification numbers: * RB3 -> CN5 diff --git a/nuttx/configs/sure-pic32mx/src/up_spi.c b/nuttx/configs/sure-pic32mx/src/up_spi.c index 36ba0844d..02ffa4f48 100644 --- a/nuttx/configs/sure-pic32mx/src/up_spi.c +++ b/nuttx/configs/sure-pic32mx/src/up_spi.c @@ -57,9 +57,11 @@ /************************************************************************************ * Definitions ************************************************************************************/ -/* The Sure PIC32MX has an SD slot connected on SPI2: + +#ifdef CONFIG_ARCH_DBDP11215 + +/* The Sure DB_DP11215 PIC32 Storage Demo Board has an SD slot connected on SPI2: * - * SPI * SCK2/PMA5/CN8/RG6 SCK SD connector SCK, FLASH (U1) SCK* * SDI2/PMA4/CN9/RG7 SDI SD connector DO, FLASH (U1) SO* * SDO2/PMA3/CN10/RG8 SDO SD connector DI, FLASH (U1) SI* @@ -73,12 +75,51 @@ * TDI/AN13/PMA10/RB13 SD_WD SD connector WD */ -#define GPIO_SD_CS (GPIO_OUTPUT|GPIO_VALUE_ONE|GPIO_PORTB|GPIO_PIN11) -#define GPIO_SD_CD (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN12) -#define GPIO_SD_WD (GPIO_INPUT|GPIO_PORTB|GPIO_PIN13) +# define PIC32_HAVE_SD 1 + +# define GPIO_SD_CS (GPIO_OUTPUT|GPIO_VALUE_ONE|GPIO_PORTB|GPIO_PIN11) +# define GPIO_SD_CD (GPIO_INPUT|GPIO_INT|GPIO_PORTB|GPIO_PIN12) +# define GPIO_SD_WD (GPIO_INPUT|GPIO_PORTB|GPIO_PIN13) + +/* The Sure DB_DP11215 PIC32 Storage Demo Board has pads an SOIC (Flash or + * EEPROM) connected on SPI2, however, U4 is not populated on my board. + * + * + * TMS/AN10/CVREFOUT/PMA13/RB10 UTIL_WP FLASH (U1) WP + * SS2/PMA2/CN11/RG9 UTIL_CS FLASH (U1) CS + */ + +# undef PIC32_HAVE_SOIC +# define GPIO_SOIC_WP (GPIO_INPUT|GPIO_PORTB|GPIO_PIN10) +# define GPIO_SOIC_CS (GPIO_OUTPUT|GPIO_VALUE_ONE|GPIO_PORTG|GPIO_PIN0) + /* Change notification numbers -- Not available for SD_CD. */ +#endif + +#ifdef CONFIG_ARCH_DBDP11212 + +/* The Sure DB-DP11212 PIC32 General Purpose Demo Board does not have an + * SD slot. + */ + +# undef PIC32_HAVE_SD + + /* The Sure DB-DP11212 PIC32 General Purpose Demo Board has an SOIC (Flash or + * EEPROM) connected on SPI2: + * + * + * TMS/AN10/PMA13/RB10 UTIL_WP FLASH (U4) WP + * TDO/AN11/PMA12/RB11 UTIL_CS FLASH (U4) CS + */ + +# define PIC32_HAVE_SOIC 1 + +# define GPIO_SOIC_WP (GPIO_INPUT|GPIO_PORTB|GPIO_PIN10) +# define GPIO_SOIC_CS (GPIO_OUTPUT|GPIO_VALUE_ONE|GPIO_PORTB|GPIO_PIN11) +#endif + /* The following enable debug output from this file. * * CONFIG_DEBUG_SPI && CONFIG_DEBUG - Define to enable basic SPI debug @@ -124,9 +165,16 @@ void weak_function pic32mx_spiinitialize(void) * write protect (WP) inputs. */ +#ifdef PIC32_HAVE_SD pic32mx_configgpio(GPIO_SD_CS); pic32mx_configgpio(GPIO_SD_CD); pic32mx_configgpio(GPIO_SD_WD); +#endif + +#ifdef PIC32_HAVE_SOIC + pic32mx_configgpio(GPIO_SOIC_WP); + pic32mx_configgpio(GPIO_SOIC_CS); +#endif } /************************************************************************************ @@ -161,32 +209,62 @@ void pic32mx_spi2select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool se /* The SD card chip select is pulled high and active low */ +#ifdef PIC32_HAVE_SD if (devid == SPIDEV_MMCSD) { pic32mx_gpiowrite(GPIO_SD_CS, !selected); } +#endif + +#ifdef PIC32_HAVE_SOIC + if (devid == SPIDEV_FLASH) + { + pic32mx_gpiowrite(GPIO_SOIC_CS, !selected); + } +#endif } uint8_t pic32mx_spi2status(FAR struct spi_dev_s *dev, enum spi_dev_e devid) { uint8_t ret = 0; - /* Card detect is pull up on-board. If a low value is sensed then the card must - * be present. + /* Card detect is pull up on-board. If a low value is sensed then the + * card must be present. */ - if (!pic32mx_gpioread(GPIO_SD_CD)) +#ifdef PIC32_HAVE_SD + if (devid == SPIDEV_MMCSD) + { + if (!pic32mx_gpioread(GPIO_SD_CD)) + { + ret = SPI_STATUS_PRESENT; + + /* It seems that a high value indicates the the card is write + * protected. + */ + + if (pic32mx_gpioread(GPIO_SD_WD)) + { + ret |= SPI_STATUS_WRPROTECTED; + } + } + } +#endif + +#ifdef PIC32_HAVE_SOIC + if (devid == SPIDEV_FLASH) { ret = SPI_STATUS_PRESENT; - /* It seems that a high value indicatest the the card is write protected. */ + /* Write protect is indicated with a low value. */ - if (pic32mx_gpioread(GPIO_SD_WD)) + if (pic32mx_gpioread(GPIO_SOIC_WP)) { ret |= SPI_STATUS_WRPROTECTED; } } - +#endif + spivdbg("Returning %d\n", ret); return ret; } diff --git a/nuttx/configs/sure-pic32mx/src/up_usbdev.c b/nuttx/configs/sure-pic32mx/src/up_usbdev.c index 667bd1837..bb175f664 100644 --- a/nuttx/configs/sure-pic32mx/src/up_usbdev.c +++ b/nuttx/configs/sure-pic32mx/src/up_usbdev.c @@ -56,7 +56,10 @@ /************************************************************************************ * Definitions ************************************************************************************/ -/* +/* The Sure DB_DP11215 PIC32 Storage Demo Board has a CP2102 PHY that is shared + * between the USB and the UART-to-USB logic. That PHY must be programmed during + * boot up for USB functionality (since the UART-to-USB is not populated). + * * PIN NAME SIGNAL NOTES * ---- ------------------------------- -------------- ------------------------------ * 11 AN5/C1IN+/Vbuson/CN7/RB5 Vbuson/AN5/RB5 To USB VBUS circuitry @@ -64,9 +67,11 @@ * 44 SCL1/IC3/PMCS2/PMA15/INT3/RD10 USB_OPT USB PHY */ -#define GPIO_USB_VBUSON (GPIO_INPUT|GPIO_PORTB|GPIO_PIN5) -#define GPIO_USB_OPTEN (GPIO_OUTPUT|GPIO_VALUE_ZERO|GPIO_PORTD|GPIO_PIN9) -#define GPIO_USB_OPT (GPIO_OUTPUT|GPIO_VALUE_ONE|GPIO_PORTD|GPIO_PIN10) +#ifdef CONFIG_ARCH_DBDP11215 +# define GPIO_USB_VBUSON (GPIO_INPUT|GPIO_PORTB|GPIO_PIN5) +# define GPIO_USB_OPTEN (GPIO_OUTPUT|GPIO_VALUE_ZERO|GPIO_PORTD|GPIO_PIN9) +# define GPIO_USB_OPT (GPIO_OUTPUT|GPIO_VALUE_ONE|GPIO_PORTD|GPIO_PIN10) +#endif /************************************************************************************ * Private Functions @@ -88,8 +93,10 @@ void weak_function pic32mx_usbdevinitialize(void) { /* Connect the PHY to the USB mini-B port. Order and timing matter! */ +#ifdef CONFIG_ARCH_DBDP11215 pic32mx_configgpio(GPIO_USB_OPTEN); pic32mx_configgpio(GPIO_USB_OPT); +#endif /* Notes from the Sure Electronics sample code: * |