1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
|
/************************************************************************************
* configs/arduino-due/include/board.h
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_ARDUINO_DUE_INCLUDE_BOARD_H
#define __CONFIGS_ARDUINO_DUE_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
# ifdef CONFIG_GPIO_IRQ
# include <arch/irq.h>
# endif
#endif
/************************************************************************************
* Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* After power-on reset, the SAM3X device is running on a 4MHz internal RC. These
* definitions will configure clocking
*
* MAINOSC: Frequency = 12MHz (crysta)
* PLLA: PLL Divider = 1, Multiplier = 14 to generate PLLACK = 168MHz
* Master Clock (MCK): Source = PLLACK, Prescalar = 1 to generate MCK = 84MHz
* CPU clock: 84MHz
*/
/* Main oscillator register settings.
*
* The start up time should be should be:
* Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles.
*/
#define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */
/* PLLA configuration.
*
* Divider = 1
* Multipler = 14
*/
#define BOARD_CKGR_PLLAR_MUL (13 << PMC_CKGR_PLLAR_MUL_SHIFT)
#define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT)
#define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS
/* PMC master clock register settings.
*
* Source = PLLA
* Divider = 2
*/
#define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA
#define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV2
/* USB UTMI PLL start-up time */
#define BOARD_CKGR_UCKR_UPLLCOUNT (3 << PMC_CKGR_UCKR_UPLLCOUNT_SHIFT)
/* Resulting frequencies */
#define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */
#define BOARD_PLLA_FREQUENCY (168000000) /* PLLACK: 14 * 12Mhz / 1 */
#define BOARD_MCK_FREQUENCY (84000000) /* MCK: PLLACK / 2 */
#define BOARD_CPU_FREQUENCY (84000000) /* CPU: MCK */
/* HSMCI clocking
*
* Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK)
* divided by (2*(CLKDIV+1)).
*
* MCI_SPEED = MCCK / (2*(CLKDIV+1))
* CLKDIV = MCCK / MCI_SPEED / 2 - 1
*
* Where CLKDIV has a range of 0-255.
*/
/* MCK = 84MHz, CLKDIV = 104, MCI_SPEED = 84MHz / 2 * (104+1) = 400 KHz */
#define HSMCI_INIT_CLKDIV (104 << HSMCI_MR_CLKDIV_SHIFT)
/* MCK = 84MHz, CLKDIV = 2, MCI_SPEED = 84MHz / 2 * (2+1) = 14 MHz */
#define HSMCI_MMCXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT)
/* MCK = 84MHz, CLKDIV = 1, MCI_SPEED = 84MHz / 2 * (1+1) = 21 MHz */
#define HSMCI_SDXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT)
#define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV
/* FLASH wait states
*
* FWS Max frequency
* 1.62V 1.8V
* --- ----- ------
* 0 24MHz 27MHz
* 1 40MHz 47MHz
* 2 72MHz 84MHz
* 3 84MHz 96MHz
*/
#define BOARD_FWS 2
/* LED definitions ******************************************************************/
/* There are two user-controllable LEDs on board the Arduino Due board:
*
* LED GPIO
* ---------------- -----
* TX Yellow LED PA21
* RX Yellow LED PC30
*
* Both are pulled high and can be illuminated by driving the corresponding
* GPIO output to low.
*/
/* LED index values for use with sam_setled() */
#define BOARD_LED_RX 0
#define BOARD_LED_TX 1
#define BOARD_NLEDS 2
/* LED bits for use with sam_setleds() */
#define BOARD_LED_RX_BIT (1 << BOARD_LED_RX)
#define BOARD_LED_TX_BIT (1 << BOARD_LED_TX)
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
* defined. In that case, the usage by the board port is defined in
* include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
* events as follows:
*
* SYMBOL Val Meaning LED state
* RX TX
* ------------------- --- ----------------------- -------- --------- */
#define LED_STARTED 0 /* NuttX has been started OFF OFF */
#define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF OFF */
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF */
#define LED_STACKCREATED 1 /* Idle stack created ON OFF */
#define LED_INIRQ 2 /* In an interrupt No change */
#define LED_SIGNAL 2 /* In a signal handler No change */
#define LED_ASSERTION 2 /* An assertion failed No change */
#define LED_PANIC 3 /* The system has crashed OFF Blinking */
#undef LED_IDLE /* MCU is is sleep mode Not used */
/* Thus if RX is statically on, NuttX has successfully booted and is,
* apparently, running normmally. If TX is flashing at approximately
* 2Hz, then a fatal error has been detected and the system has halted.
*/
/* Button definitions ***************************************************************/
/* There are no buttons on the Arduino Due board. */
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: sam_boardinitialize
*
* Description:
* All SAM3X architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
void sam_boardinitialize(void);
/************************************************************************************
* Name: sam_ledinit, sam_setled, and sam_setleds
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LEDs. If
* CONFIG_ARCH_LEDS is not defined, then the following interfacesare available to
* control the LEDs from user applications.
*
************************************************************************************/
#ifndef CONFIG_ARCH_LEDS
void sam_ledinit(void);
void sam_setled(int led, bool ledon);
void sam_setleds(uint8_t ledset);
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_ARDUINO_DUE_INCLUDE_BOARD_H */
|