1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
pirelli_dpl10
=============
This directory contains the board support for Pirelli "Discus" DP-L10
phones.
This port is a variant of the compal_e88 configuration with the small
change of enabling the IrDA serial console:
* CONFIG_SERIAL_IRDA_CONSOLE=y
This port is based on patches contributed by Denis Carikli for both the
compal e99 and e88. At the time of initial check-in, the following phones
were tested:
* Pirelli DPL-10 nsh_highram loaded via romload in osmocon
The patches were made by Alan Carvalho de Assis and Denis Carikli using
the Stefan Richter's patches that can be found here:
http://cgit.osmocom.org/cgit/nuttx-bb/log/?h=lputt%2Ftesting
Osmocom-BB Dependencies and Sercomm
===================================
The build environment assumes that you have the osmocom-bb project
directory at same level as the nuttx project:
|- nuttx
|- apps
`- osmocom-bb
If you attempt to build this configuration without osmocom-bb, and that
you added support for sercomm in your configuration(CONFIG_SERCOMM_CONSOLE=y)
you will get compilation errors in drivers/sercomm due to header files that
are needed from the osmocom-bb directory.
By default, NuttX will not use sercomm (HDLC protocol) to communicate with
the host system. Sercomm is the transport used by osmocom-bb that runs on top
of serial. See http://bb.osmocom.org/trac/wiki/nuttx-bb/run for detailed
the usage of nuttx with sercomm.
Loading NuttX
=============
The osmocom-bb wiki describes how to load NuttX. See
http://bb.osmocom.org/trac/wiki/nuttx-bb for detailed information.
The way that nuttx is loaded depends on the configuration (highram/compalram)
and phone:
o compalram is for the ramloader(for phone having a bootloader on flash)
o highram is for phones having the romloader(if the phone has a bootrom)
or for loading in the ram trough a special loader(loaded first on ram
by talking to the ramloader) when having a ramloader(which can only
load 64k).
JTAG and Alternative Serial Console
===================================
JTAG
All JTAG lines, as well as the second uart (UART_MODEM), go to the
unpopulated connector next to the display connector.
--- ---------------------------
PIN SIGNAL
--- ---------------------------
1 Vcc
2 RX_MODEM
3 TESTRSTz (Iota)
4 TDI
5 TMS
6 TCK
7 TX_MODEM
8 TDO
9 N/C
10 GND
11 N/C
12 N/C
--- ---------------------------
JTAG Apapter:
------- ----------- --------------- --------------------------------------
JTAG 20-PIN DESCRIPTION NOTES
SIGNAL CONNECTOR
------- ----------- --------------- --------------------------------------
Vcc 1, 2 Vcc
nTRST 3 Reset Connect this pin to the (active
low) reset input of the target MCU.
Some JTAG adapters driver nTRST (high
and low). Others can can configure
nTRST as open collector (only drive
low).
GND 4, 6, 8, Ground
10, 12, 14,
16, 20
TDI 5 JTAG Test Data Use 10K-100K Ohm pull-up resistor to
Input VCC
TMS 7 JTAG Test Mode Use 10K-100K Ohm pull-up resistor to
Select VCC
TCK 9 Clock into the Use 10K-100K Ohm pull-down resistor to
core GND
RTCK 11 Return clock Some JTAG adapters have adaptive clocking
using an RTCK signal.
DBGSEL 11 Debug Select Some devices have special pins that
enable the JTAG interface. For example,
on the NXP LPC2129 the signal RTCK must
be driven low during RESET to enable the
JTAG interface.
TDO 13 JTAG Test Data Use 10K-100K Ohm pull-up resistor to VCC
Output
DBGRQ 17 N/C
DGBACK 19 N/C
ISP ?? ISP Most NXP MCU's have an ISP pin which
(when pulled low) can be used to cause
the MCU to enter a bootloader on reset.
Use 10K-100K Ohm pull up resistor.
------- ----------- --------------- --------------------------------------
|
