1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
|
README
======
This README discusses issues unique to NuttX configurations for the
STMicro STM3220G-EVAL development board.
Contents
========
- Development Environment
- GNU Toolchain Options
- IDEs
- NuttX EABI "buildroot" Toolchain
- NuttX OABI "buildroot" Toolchain
- NXFLAT Toolchain
- STM3220G-EVAL-specific Configuration Options
- LEDs
- Ethernet
- PWM
- CAN
- FSMC SRAM
- I/O Expanders
- STM3220G-EVAL-specific Configuration Options
- Configurations
Development Environment
=======================
Linux, OS X or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems. Testing was performed using the Cygwin
environment because the Raisonance R-Link emulatator and some RIDE7 development tools
were used and those tools works only under Windows.
GNU Toolchain Options
=====================
Toolchain Configurations
------------------------
The NuttX make system has been modified to support the following different
toolchain options.
1. The CodeSourcery GNU toolchain,
2. The Atollic Toolchain,
3. The devkitARM GNU toolchain,
4. Raisonance GNU toolchain,
5. The NuttX buildroot Toolchain (see below), or
6. Any generic arm-none-eabi GNU toolchain.
Most testing has been conducted using the CodeSourcery toolchain for Windows and
that is the default toolchain in most configurations. To use the Atollic
devkitARM, Raisonance GNU, or NuttX buildroot toolchain, you simply need to
add one of the following configuration options to your .config (or defconfig)
file:
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_STM32_ATOLLIC_LITE=y : The free, "Lite" version of Atollic toolchain under Windows
CONFIG_STM32_ATOLLIC_PRO=y : The paid, "Pro" version of Atollic toolchain under Windows
CONFIG_STM32_DEVKITARM=y : devkitARM under Windows
CONFIG_STM32_RAISONANCE=y : Raisonance RIDE7 under Windows
CONFIG_STM32_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABI : Generic arm-none-eabi toolchain
If you change the default toolchain, then you may also have to modify the PATH in
the setenv.h file if your make cannot find the tools.
The toolchain may also be set using the mconf utility (make menuconfig) or by
passing CONFIG_ARMV7M_TOOLCHAIN=<toolchain> to make, where <toolchain> is one
of CODESOURCERYW, CODESOURCERYL, ATOLLOC, DEVKITARM, RAISONANCE, BUILDROOT or
GNU_EABI as described above.
NOTE: the CodeSourcery (for Windows), Atollic, devkitARM, and Raisonance toolchains are
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had no effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:
make clean_context all
An alias in your .bashrc file might make that less painful.
3. Dependencies are not made when using Windows versions of the GCC. This is
because the dependencies are generated using Windows pathes which do not
work with the Cygwin make.
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
The CodeSourcery Toolchain (2009q1)
-----------------------------------
The CodeSourcery toolchain (2009q1) does not work with default optimization
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
-Os.
The Atollic "Pro" and "Lite" Toolchain
--------------------------------------
One problem that I had with the Atollic toolchains is that the provide a gcc.exe
and g++.exe in the same bin/ file as their ARM binaries. If the Atollic bin/ path
appears in your PATH variable before /usr/bin, then you will get the wrong gcc
when you try to build host executables. This will cause to strange, uninterpretable
errors build some host binaries in tools/ when you first make.
The Atollic "Lite" Toolchain
----------------------------
The free, "Lite" version of the Atollic toolchain does not support C++ nor
does it support ar, nm, objdump, or objdcopy. If you use the Atollic "Lite"
toolchain, you will have to set:
CONFIG_HAVE_CXX=n
In order to compile successfully. Otherwise, you will get errors like:
"C++ Compiler only available in TrueSTUDIO Professional"
The make may then fail in some of the post link processing because of some of
the other missing tools. The Make.defs file replaces the ar and nm with
the default system x86 tool versions and these seem to work okay. Disable all
of the following to avoid using objcopy:
CONFIG_RRLOAD_BINARY=n
CONFIG_INTELHEX_BINARY=n
CONFIG_MOTOROLA_SREC=n
CONFIG_RAW_BINARY=n
devkitARM
---------
The devkitARM toolchain includes a version of MSYS make. Make sure that the
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
path or will get the wrong version of make.
Generic arm-none-eabi GNU Toolchain
-----------------------------------
There are a number of toolchain projects providing support for the Cortex-M
class processors, including:
GCC ARM Embedded
https://launchpad.net/gcc-arm-embedded
Thumb2 Newlib Toolchain
https://github.com/EliasOenal/TNT
Summon ARM Toolchain
https://github.com/esden/summon-arm-toolchain
Yagarto
http://www.yagarto.de
Others exist for various Linux distributions, MacPorts, etc. Any version
based on GCC 4.6.3 or later should work.
IDEs
====
NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project.
Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).
Native Build
------------
Here are a few tips before you start that effort:
1) Select the toolchain that you will be using in your .config file
2) Start the NuttX build at least one time from the Cygwin command line
before trying to create your project. This is necessary to create
certain auto-generated files and directories that will be needed.
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
4) All assembly files need to have the definition option -D __ASSEMBLY__
on the command line.
Startup files will probably cause you some headaches. The NuttX startup file
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
one time from the Cygwin command line in order to obtain the pre-built
startup object needed by RIDE.
NuttX EABI "buildroot" Toolchain
================================
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
different from the default in your PATH variable).
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
SourceForge download site (https://sourceforge.net/projects/nuttx/files/buildroot/).
This GNU toolchain builds and executes in the Linux or Cygwin environment.
1. You must have already configured Nuttx in <some-dir>/nuttx.
cd tools
./configure.sh stm3220g-eval/<sub-dir>
2. Download the latest buildroot package into <some-dir>
3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
4. cd <some-dir>/buildroot
5. cp configs/cortexm3-eabi-defconfig-4.6.3 .config
6. make oldconfig
7. make
8. Edit setenv.h, if necessary, so that the PATH variable includes
the path to the newly built binaries.
See the file configs/README.txt in the buildroot source tree. That has more
details PLUS some special instructions that you will need to follow if you are
building a Cortex-M3 toolchain for Cygwin under Windows.
NOTE: Unfortunately, the 4.6.3 EABI toolchain is not compatible with the
the NXFLAT tools. See the top-level TODO file (under "Binary loaders") for
more information about this problem. If you plan to use NXFLAT, please do not
use the GCC 4.6.3 EABI toochain; instead use the GCC 4.3.3 OABI toolchain.
See instructions below.
NuttX OABI "buildroot" Toolchain
================================
The older, OABI buildroot toolchain is also available. To use the OABI
toolchain:
1. When building the buildroot toolchain, either (1) modify the cortexm3-eabi-defconfig-4.6.3
configuration to use EABI (using 'make menuconfig'), or (2) use an exising OABI
configuration such as cortexm3-defconfig-4.3.3
2. Modify the Make.defs file to use the OABI conventions:
+CROSSDEV = arm-nuttx-elf-
+ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-gotoff.ld -no-check-sections
-CROSSDEV = arm-nuttx-eabi-
-ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
-NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections
NXFLAT Toolchain
================
If you are *not* using the NuttX buildroot toolchain and you want to use
the NXFLAT tools, then you will still have to build a portion of the buildroot
tools -- just the NXFLAT tools. The buildroot with the NXFLAT tools can
be downloaded from the NuttX SourceForge download site
(https://sourceforge.net/projects/nuttx/files/).
This GNU toolchain builds and executes in the Linux or Cygwin environment.
1. You must have already configured Nuttx in <some-dir>/nuttx.
cd tools
./configure.sh lpcxpresso-lpc1768/<sub-dir>
2. Download the latest buildroot package into <some-dir>
3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
4. cd <some-dir>/buildroot
5. cp configs/cortexm3-defconfig-nxflat .config
6. make oldconfig
7. make
8. Edit setenv.h, if necessary, so that the PATH variable includes
the path to the newly builtNXFLAT binaries.
Ethernet
========
The Ethernet driver is configured to use the MII interface:
Board Jumper Settings:
Jumper Description
JP8 To enable MII, JP8 should not be fitted.
JP6 2-3: Enable MII interface mode
JP5 2-3: Provide 25 MHz clock for MII or 50 MHz clock for RMII by MCO at PA8
SB1 Not used with MII
LEDs
====
The STM3220G-EVAL board has four LEDs labeled LD1, LD2, LD3 and LD4 on the
board.. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/up_leds.c. The LEDs are used to encode OS-related\
events as follows:
SYMBOL Meaning LED1* LED2 LED3 LED4
------------------- ----------------------- ------- ------- ------- ------
LED_STARTED NuttX has been started ON OFF OFF OFF
LED_HEAPALLOCATE Heap has been allocated OFF ON OFF OFF
LED_IRQSENABLED Interrupts enabled ON ON OFF OFF
LED_STACKCREATED Idle stack created OFF OFF ON OFF
LED_INIRQ In an interrupt** ON N/C N/C OFF
LED_SIGNAL In a signal handler*** N/C ON N/C OFF
LED_ASSERTION An assertion failed ON ON N/C OFF
LED_PANIC The system has crashed N/C N/C N/C ON
LED_IDLE STM32 is is sleep mode (Optional, not used)
* If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot
and these LEDs will give you some indication of where the failure was
** The normal state is LED3 ON and LED1 faintly glowing. This faint glow
is because of timer interupts that result in the LED being illuminated
on a small proportion of the time.
*** LED2 may also flicker normally if signals are processed.
PWM
===
The STM3220G-Eval has no real on-board PWM devices, but the board can be
configured to output a pulse train using timer output pins. The following
pins have been use to generate PWM output (see board.h for some other
candidates):
TIM4 CH2. Pin PD13 is used by the FSMC (FSMC_A18) and is also connected
to the Motor Control Connector (CN5) just for this purpose. If FSMC is
not enabled, then FSMC_A18 will not be used (and will be tri-stated from
the LCD).
CONFIGURATION:
CONFIG_STM32_TIM4=y
CONFIG_PWM=n
CONFIG_PWM_PULSECOUNT=n
CONFIG_STM32_TIM4_PWM=y
CONFIG_STM32_TIM4_CHANNEL=2
ACCESS:
Daughterboard Extension Connector, CN3, pin 32
Ground is available on CN3, pin1
NOTE: TIM4 hardware will not support pulse counting.
TIM8 CH4: Pin PC9 is used by the microSD card (MicroSDCard_D1) and I2S
(I2S_CKIN) but can be completely disconnected from both by opening JP16.
CONFIGURATION:
CONFIG_STM32_TIM8=y
CONFIG_PWM=n
CONFIG_PWM_PULSECOUNT=y
CONFIG_STM32_TIM8_PWM=y
CONFIG_STM32_TIM8_CHANNEL=4
ACCESS:
Daughterboard Extension Connector, CN3, pin 17
Ground is available on CN3, pin1
CAN
===
Connector 10 (CN10) is DB-9 male connector that can be used with CAN1 or CAN2.
JP10 connects CAN1_RX or CAN2_RX to the CAN transceiver
JP3 connects CAN1_TX or CAN2_TX to the CAN transceiver
CAN signals are then available on CN10 pins:
CN10 Pin 7 = CANH
CN10 Pin 2 = CANL
Mapping to STM32 GPIO pins:
PD0 = FSMC_D2 & CAN1_RX
PD1 = FSMC_D3 & CAN1_TX
PB13 = ULPI_D6 & CAN2_TX
PB5 = ULPI_D7 & CAN2_RX
Configuration Options:
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
Standard 11-bit IDs.
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4
CONFIG_STM32_CAN1 - Enable support for CAN1
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_STM32_CAN2 - Enable support for CAN2
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an
dump of all CAN registers.
FSMC SRAM
=========
On-board SRAM
-------------
A 16 Mbit SRAM is connected to the STM32F407IGH6 FSMC bus which shares the same
I/Os with the CAN1 bus. Jumper settings:
JP1: Connect PE4 to SRAM as A20
JP2: onnect PE3 to SRAM as A19
JP3 and JP10 must not be fitted for SRAM and LCD application. JP3 and JP10
select CAN1 or CAN2 if fitted; neither if not fitted.
The on-board SRAM can be configured by setting
CONFIG_STM32_FSMC=y
CONFIG_STM32_FSMC_SRAM=y
CONFIG_HEAP2_BASE=0x64000000
CONFIG_HEAP2_SIZE=2097152
CONFIG_MM_REGIONS=2
Configuration Options
---------------------
Internal SRAM is available in all members of the STM32 family. In addition
to internal SRAM, SRAM may also be available through the FSMC. In order to
use FSMC SRAM, the following additional things need to be present in the
NuttX configuration file:
CONFIG_STM32_FSMC=y : Enables the FSMC
CONFIG_STM32_FSMC_SRAM=y : Indicates that SRAM is available via the
FSMC (as opposed to an LCD or FLASH).
CONFIG_HEAP2_BASE : The base address of the SRAM in the FSMC
address space
CONFIG_HEAP2_SIZE : The size of the SRAM in the FSMC
address space
CONFIG_MM_REGIONS : Must be set to a large enough value to
include the FSMC SRAM
SRAM Configurations
-------------------
There are 2 possible SRAM configurations:
Configuration 1. System SRAM (only)
CONFIG_MM_REGIONS == 1
Configuration 2. System SRAM and FSMC SRAM
CONFIG_MM_REGIONS == 2
CONFIG_STM32_FSMC_SRAM defined
I/O Expanders
=============
The STM3220G-EVAL has two STMPE811QTR I/O expanders on board both connected to
the STM32 via I2C1. They share a common interrupt line: PI2.
STMPE811 U24, I2C address 0x41 (7-bit)
------ ---- ---------------- --------------------------------------------
STPE11 PIN BOARD SIGNAL BOARD CONNECTION
------ ---- ---------------- --------------------------------------------
Y- TouchScreen_Y- LCD Connector XL
X- TouchScreen_X- LCD Connector XR
Y+ TouchScreen_Y+ LCD Connector XD
X+ TouchScreen_X+ LCD Connector XU
IN3 EXP_IO9
IN2 EXP_IO10
IN1 EXP_IO11
IN0 EXP_IO12
STMPE811 U29, I2C address 0x44 (7-bit)
------ ---- ---------------- --------------------------------------------
STPE11 PIN BOARD SIGNAL BOARD CONNECTION
------ ---- ---------------- --------------------------------------------
Y- EXP_IO1
X- EXP_IO2
Y+ EXP_IO3
X+ EXP_IO4
IN3 EXP_IO5
IN2 EXP_IO6
IN1 EXP_IO7
IN0 EXP_IO8
STM3220G-EVAL-specific Configuration Options
============================================
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=arm
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_ARM=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_CORTEXM3=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP=stm32
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_STM32F207IG=y
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
configuration features.
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=stm3220g_eval (for the STM3220G-EVAL development board)
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_STM3220G_EVAL=y
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
CONFIG_DRAM_START - The start address of installed DRAM
CONFIG_DRAM_START=0x20000000
In addition to internal SRAM, SRAM may also be available through the FSMC.
In order to use FSMC SRAM, the following additional things need to be
present in the NuttX configuration file:
CONFIG_STM32_FSMC_SRAM - Indicates that SRAM is available via the
FSMC (as opposed to an LCD or FLASH).
CONFIG_HEAP2_BASE - The base address of the SRAM in the FSMC address space (hex)
CONFIG_HEAP2_SIZE - The size of the SRAM in the FSMC address space (decimal)
CONFIG_ARCH_IRQPRIO - The STM3220xxx supports interrupt prioritization
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
Individual subsystems can be enabled:
AHB1
----
CONFIG_STM32_CRC
CONFIG_STM32_BKPSRAM
CONFIG_STM32_DMA1
CONFIG_STM32_DMA2
CONFIG_STM32_ETHMAC
CONFIG_STM32_OTGHS
AHB2
----
CONFIG_STM32_DCMI
CONFIG_STM32_CRYP
CONFIG_STM32_HASH
CONFIG_STM32_RNG
CONFIG_STM32_OTGFS
AHB3
----
CONFIG_STM32_FSMC
APB1
----
CONFIG_STM32_TIM2
CONFIG_STM32_TIM3
CONFIG_STM32_TIM4
CONFIG_STM32_TIM5
CONFIG_STM32_TIM6
CONFIG_STM32_TIM7
CONFIG_STM32_TIM12
CONFIG_STM32_TIM13
CONFIG_STM32_TIM14
CONFIG_STM32_WWDG
CONFIG_STM32_IWDG
CONFIG_STM32_SPI2
CONFIG_STM32_SPI3
CONFIG_STM32_USART2
CONFIG_STM32_USART3
CONFIG_STM32_UART4
CONFIG_STM32_UART5
CONFIG_STM32_I2C1
CONFIG_STM32_I2C2
CONFIG_STM32_I2C3
CONFIG_STM32_CAN1
CONFIG_STM32_CAN2
CONFIG_STM32_DAC1
CONFIG_STM32_DAC2
CONFIG_STM32_PWR -- Required for RTC
APB2
----
CONFIG_STM32_TIM1
CONFIG_STM32_TIM8
CONFIG_STM32_USART1
CONFIG_STM32_USART6
CONFIG_STM32_ADC1
CONFIG_STM32_ADC2
CONFIG_STM32_ADC3
CONFIG_STM32_SDIO
CONFIG_STM32_SPI1
CONFIG_STM32_SYSCFG
CONFIG_STM32_TIM9
CONFIG_STM32_TIM10
CONFIG_STM32_TIM11
Timer devices may be used for different purposes. One special purpose is
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
is defined (as above) then the following may also be defined to indicate that
the timer is intended to be used for pulsed output modulation, ADC conversion,
or DAC conversion. Note that ADC/DAC require two definition: Not only do you have
to assign the timer (n) for used by the ADC or DAC, but then you also have to
configure which ADC or DAC (m) it is assigned to.
CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,14
CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2
For each timer that is enabled for PWM usage, we need the following additional
configuration settings:
CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
NOTE: The STM32 timers are each capable of generating different signals on
each of the four channels with different duty cycles. That capability is
not supported by this driver: Only one output channel per timer.
JTAG Enable settings (by default JTAG-DP and SW-DP are disabled):
CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
but without JNTRST.
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
STM3220xxx specific device driver settings
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
m (m=4,5) for the console and ttys0 (default is the USART1).
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_U[S]ARTn_2STOP - Two stop bits
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
support. Non-interrupt-driven, poll-waiting is recommended if the
interrupt rate would be to high in the interrupt driven case.
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
and CONFIG_STM32_DMA2.
CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
Default: Medium
CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
4-bit transfer mode.
CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board
CONFIG_STM32_MII - Support Ethernet MII interface
CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface
CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface
CONFIG_STM32_RMII - Support Ethernet RMII interface
CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode
CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select full duplex mode. Default: half-duplex
CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select 100 MBps speed. Default: 10 Mbps
CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is
defined. The PHY status register address may diff from PHY to PHY. This
configuration sets the address of the PHY status register.
CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides bit mask indicating 10 or 100MBps speed.
CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the speed bit(s) indicating 100MBps speed.
CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provide bit mask indicating full or half duplex modes.
CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the mode bits indicating full duplex mode.
CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported
but some hooks are indicated with this condition.
STM3220G-EVAL CAN Configuration
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
mode for testing. The STM32 CAN driver does support loopback mode.
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an
dump of all CAN registers.
STM3220G-EVAL LCD Hardware Configuration
STM32 USB OTG FS Host Driver Support
Pre-requisites
CONFIG_USBHOST - Enable general USB host support
CONFIG_STM32_OTGFS - Enable the STM32 USB OTG FS block
CONFIG_STM32_SYSCFG - Needed
Options:
CONFIG_STM32_OTGFS_RXFIFO_SIZE - Size of the RX FIFO in 32-bit words.
Default 128 (512 bytes)
CONFIG_STM32_OTGFS_NPTXFIFO_SIZE - Size of the non-periodic Tx FIFO
in 32-bit words. Default 96 (384 bytes)
CONFIG_STM32_OTGFS_PTXFIFO_SIZE - Size of the periodic Tx FIFO in 32-bit
words. Default 96 (384 bytes)
CONFIG_STM32_OTGFS_DESCSIZE - Maximum size of a descriptor. Default: 128
CONFIG_STM32_OTGFS_SOFINTR - Enable SOF interrupts. Why would you ever
want to do that?
CONFIG_STM32_USBHOST_REGDEBUG - Enable very low-level register access
debug. Depends on CONFIG_DEBUG.
CONFIG_STM32_USBHOST_PKTDUMP - Dump all incoming and outgoing USB
packets. Depends on CONFIG_DEBUG.
Configurations
==============
Each STM3220G-EVAL configuration is maintained in a sudirectory and
can be selected as follow:
cd tools
./configure.sh stm3220g-eval/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following:
dhcpd:
-----
This builds the DCHP server using the apps/examples/dhcpd application
(for execution from FLASH.) See apps/examples/README.txt for information
about the dhcpd example. The server address is 10.0.0.1 and it serves
IP addresses in the range 10.0.0.2 through 10.0.0.17 (all of which, of
course, are configurable).
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
nettest:
-------
This configuration directory may be used to verify networking performance
using the STM32's Ethernet controller. It uses apps/examples/nettest to excercise the
TCP/IP network.
CONFIG_EXAMPLES_NETTEST_SERVER=n : Target is configured as the client
CONFIG_EXAMPLES_NETTEST_PERFORMANCE=y : Only network performance is verified.
CONFIG_EXAMPLES_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2) : Target side is IP: 10.0.0.2
CONFIG_EXAMPLES_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host side is IP: 10.0.0.1
CONFIG_EXAMPLES_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1) : Server address used by which ever is client.
nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. The
Configuration enables both the serial and telnet NSH interfaces.
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_NSH_DHCPC=n : DHCP is disabled
CONFIG_NSH_IPADDR=(192<<24|168<<16|13<<8|161) : Target IP address 192.168.8.161
CONFIG_NSH_DRIPADDR=(192<<24|168<<16|13<<8|1) : Host IP address 192.168.8.1
NOTES:
1. This example assumes that a network is connected. During its
initialization, it will try to negotiate the link speed. If you have
no network connected when you reset the board, there will be a long
delay (maybe 30 seconds?) before anything happens. That is the timeout
before the networking finally gives up and decides that no network is
available.
2. This example supports the ADC test (apps/examples/adc) but this must
be manually enabled by selecting:
CONFIG_ADC=y : Enable the generic ADC infrastructure
CONFIG_STM32_ADC3=y : Enable ADC3
CONFIG_STM32_TIM1=y : Enable Timer 1
CONFIG_STM32_TIM1_ADC=y : Indicate that timer 1 will be used to trigger an ADC
CONFIG_STM32_TIM1_ADC3=y : Assign timer 1 to drive ADC3 sampling
CONFIG_STM32_ADC3_SAMPLE_FREQUENCY=100 : Select a sampling frequency
See also apps/examples/README.txt
General debug for analog devices (ADC/DAC):
CONFIG_DEBUG_ANALOG
3. This example supports the PWM test (apps/examples/pwm) but this must
be manually enabled by selecting eeither
CONFIG_PWM=y : Enable the generic PWM infrastructure
CONFIG_PWM_PULSECOUNT=n : Disable to support for TIM1/8 pulse counts
CONFIG_STM32_TIM4=y : Enable TIM4
CONFIG_STM32_TIM4_PWM=y : Use TIM4 to generate PWM output
CONFIG_STM32_TIM4_CHANNEL=2 : Select output on TIM4, channel 2
If CONFIG_STM32_FSMC is disabled, output will appear on CN3, pin 32.
Ground is available on CN3, pin1.
Or..
CONFIG_PWM=y : Enable the generic PWM infrastructure
CONFIG_PWM_PULSECOUNT=y : Enable to support for TIM1/8 pulse counts
CONFIG_STM32_TIM8=y : Enable TIM8
CONFIG_STM32_TIM8_PWM=y : Use TIM8 to generate PWM output
CONFIG_STM32_TIM8_CHANNEL=4 : Select output on TIM8, channel 4
If CONFIG_STM32_FSMC is disabled, output will appear on CN3, pin 17
Ground is available on CN23 pin1.
See also include/board.h and apps/examples/README.txt
Special PWM-only debug options:
CONFIG_DEBUG_PWM
4. This example supports the CAN loopback test (apps/examples/can) but this
must be manually enabled by selecting:
CONFIG_CAN=y : Enable the generic CAN infrastructure
CONFIG_CAN_EXID=y or n : Enable to support extended ID frames
CONFIG_STM32_CAN1=y : Enable CAN1
CONFIG_CAN_LOOPBACK=y : Enable CAN loopback mode
See also apps/examples/README.txt
Special CAN-only debug options:
CONFIG_DEBUG_CAN
CONFIG_CAN_REGDEBUG
5. This example can support an FTP client. In order to build in FTP client
support simply uncomment the following lines in the appconfig file (before
configuring) or in the apps/.config file (after configuring):
#CONFIGURED_APPS += netutils/ftpc
#CONFIGURED_APPS += examples/ftpc
6. This example can support an FTP server. In order to build in FTP server
support simply uncomment the following lines in the appconfig file (before
configuring) or in the apps/.config file (after configuring):
#CONFIGURED_APPS += netutils/ftpd
#CONFIGURED_APPS += examples/ftpd
And enable poll() support in the NuttX configuration file:
CONFIG_DISABLE_POLL=n
7. This example supports the watchdog timer test (apps/examples/watchdog)
but this must be manually enabled by selecting:
CONFIG_WATCHDOG=y : Enables watchdog timer driver support
CONFIG_STM32_WWDG=y : Enables the WWDG timer facility, OR
CONFIG_STM32_IWDG=y : Enables the IWDG timer facility (but not both)
The WWDG watchdog is driven off the (fast) 42MHz PCLK1 and, as result,
has a maximum timeout value of 49 milliseconds. For WWDG watchdog, you
should also add the fillowing to the configuration file:
CONFIG_EXAMPLES_WATCHDOG_PINGDELAY=20
CONFIG_EXAMPLES_WATCHDOG_TIMEOUT=49
The IWDG timer has a range of about 35 seconds and should not be an issue.
7. Adding LCD and graphics support:
appconfig (apps/.config): Enable the application configurations that you
want to use. Asexamples:
CONFIGURED_APPS += examples/nx : Pick one or more
CONFIGURED_APPS += examples/nxhello :
CONFIGURED_APPS += examples/nximage :
CONFIGURED_APPS += examples/nxlines :
defconfig (nuttx/.config):
CONFIG_STM32_FSMC=y : FSMC support is required for the LCD
CONFIG_NX=y : Enable graphics suppport
CONFIG_MM_REGIONS=2 : When FSMC is enabled, so is the on-board SRAM memory region
8. USB OTG FS Device or Host Support
CONFIG_USBDEV - Enable USB device support, OR
CONFIG_USBHOST - Enable USB host support (but not both)
CONFIG_STM32_OTGFS - Enable the STM32 USB OTG FS block
CONFIG_STM32_SYSCFG - Needed for all USB OTF FS support
CONFIG_SCHED_WORKQUEUE - Worker thread support is required for the mass
storage class (both host and device).
CONFIG_NSH_ARCHINIT - Architecture specific USB initialization
is needed
9. This configuration requires that jumper JP22 be set to enable RS-232 operation.
nsh2:
-----
This is an alternaitve NSH configuration. One limitation of the STM3220G-EVAL
board is that you cannot have both a UART-based NSH console and SDIO support.
The nsh2 differs from the nsh configuration in the following ways:
-CONFIG_STM32_USART3=y : USART3 is disabled
+ CONFIG_STM32_USART3=n
-CONFIG_STM32_SDIO=n : SDIO is enabled
+CONFIG_STM32_SDIO=y
Logically, these are the only differences: This configuration has SDIO (and
the SD card) enabled and the serial console disabled. There is ONLY a
Telnet console!.
There are some special settings to make life with only a Telnet
CONFIG_SYSLOG=y - Enables the System Logging feature.
CONFIG_RAMLOG=y - Enable the RAM-based logging feature.
CONFIG_RAMLOG_CONSOLE=y - Use the RAM logger as the default console.
This means that any console output from non-Telnet threads will
go into the circular buffer in RAM.
CONFIG_RAMLOG_SYSLOG - This enables the RAM-based logger as the
system logger. This means that (1) in addition to the console
output from other tasks, ALL of the debug output will also to
to the circular buffer in RAM, and (2) NSH will now support a
command called 'dmesg' that can be used to dump the RAM log.
There are a few other configuration differences as necessary to support
this different device configuration. Just the do the 'diff' if you are
curious.
NOTES:
1. See the notes for the nsh configuration. Most also apply to the nsh2
configuration.
2. RS-232 is disabled, but Telnet is still available for use as a console.
Since RS-232 and SDIO use the same pins (one controlled by JP22), RS232
and SDIO cannot be used concurrently.
3. This configuration requires that jumper JP22 be set to enable SDIO
operation. To enable MicroSD Card, which shares same I/Os with RS-232,
JP22 is not fitted.
4. In order to use SDIO without overruns, DMA must be used.
5. Another SDIO/DMA issue. This one is probably a software bug. This is
the bug as stated in the TODO list:
"If you use a large I/O buffer to access the file system, then the
MMCSD driver will perform multiple block SD transfers. With DMA
ON, this seems to result in CRC errors detected by the hardware
during the transfer. Workaround: CONFIG_MMCSD_MULTIBLOCK_DISABLE=y"
For this reason, CONFIG_MMCSD_MULTIBLOCK_DISABLE=y appears in the defconfig
file.
6. Another DMA-related concern. I see this statement in the reference
manual: "The burst configuration has to be selected in order to respect
the AHB protocol, where bursts must not cross the 1 KB address boundary
because the minimum address space that can be allocated to a single slave
is 1 KB. This means that the 1 KB address boundary should not be crossed
by a burst block transfer, otherwise an AHB error would be generated,
that is not reported by the DMA registers."
There is nothing in the DMA driver to prevent this now.
nxwm
----
This is a special configuration setup for the NxWM window manager
UnitTest. The NxWM window manager can be found here:
nuttx-code/NxWidgets/nxwm
The NxWM unit test can be found at:
nuttx-code/NxWidgets/UnitTests/nxwm
Documentation for installing the NxWM unit test can be found here:
nuttx-code/NxWidgets/UnitTests/README.txt
Here is the quick summary of the build steps (Assuming that all of
the required packages are available in a directory ~/nuttx-code):
1. Intall the nxwm configuration
$ cd ~/nuttx-code/nuttx/tools
$ ./configure.sh stm3220g-eval/nxwm
2. Make the build context (only)
$ cd ..
$ . ./setenv.sh
$ make context
...
3. Install the nxwm unit test
$ cd ~/nuttx-code/NxWidgets
$ tools/install.sh ~/nuttx-code/apps nxwm
Creating symbolic link
- To ~/nuttx-code/NxWidgets/UnitTests/nxwm
- At ~/nuttx-code/apps/external
4. Build the NxWidgets library
$ cd ~/nuttx-code/NxWidgets/libnxwidgets
$ make TOPDIR=~/nuttx-code/nuttx
...
5. Build the NxWM library
$ cd ~/nuttx-code/NxWidgets/nxwm
$ make TOPDIR=~/nuttx-code/nuttx
...
6. Built NuttX with the installed unit test as the application
$ cd ~/nuttx-code/nuttx
$ make
NOTES:
1. This configuration uses the mconf-based configuration tool. To
change this configuration using that tool, you should:
a. Build and install the mconf tool. See nuttx/README.txt and
misc/tools/
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. This configuration is currently set up to build under Cygwin on
a Windows machine using the CodeSourcery Windows toolchain.
That configuration can be easy changed as described in Note 1.
ostest:
------
This configuration directory, performs a simple OS test using
examples/ostest. By default, this project assumes that you are
using the DFU bootloader.
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
telnetd:
--------
A simple test of the Telnet daemon(see apps/netutils/README.txt,
apps/examples/README.txt, and apps/examples/telnetd). This is
the same daemon that is used in the nsh configuration so if you
use NSH, then you don't care about this. This test is good for
testing the Telnet daemon only because it works in a simpler
environment than does the nsh configuration.
|