1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
|
configs/pic32mx README
=====================
This README file discusses the port of NuttX to the "Advanced USB Storage
Demo Board," Model DB-DP11215, from Sure Electronics
(http://www.sureelectronics.net/). This board features the MicroChip
PIC32MX440F512H. See also http://www.sureelectronics.net/goods.php?id=1168
for further information about the Sure DB-DP11215 board.
DB_DP11215 PIC32 Storage Demo Board
- PIC32MX44F512H
- SD card slot
- RS-2323 Interface
- USB (MINI-B)
- 2x16 LCD display
- Three tactile switches
- Four user LEDs
Also available (but not yet supported).
DB-DP11212 PIC32 General Purpose Demo Board
- PIC32MX44F512H
- LM75A temperature sensor and temperature resistor (NTC-SMD thermistor)
- SPI FLASH: AT25DF041A
- USB (MINI-B)
- 2x16 LCD display
- 4 digit, 8 segment LED display
- Three tactile switches
- Four user LEDs
NOTE: I see that Sure Electronics shows both of these boards at end-of-Life
(EOL). So I assume that these boards will no longer be generally available.
This work should still be useful, however, for other PIC32MX4-based boards
(2012-5-27).
Contents
========
PIC32MX440F512H Pin Out
Toolchains
Loading NuttX with PICkit2
LCD1602
PIC32MX Configuration Options
Configurations
PIC32MX440F512H Pin Out
=======================
DB_DP11215 PIC32 Storage Demo Board
-----------------------------------
PIC32MX440F512H 64-Pin QFN (USB) Pin Out as used on the DB_DP11215 PIC32 Storage
Demo Board.
LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
1 PMD5/RE5 PMPD5 Display, JP1-12, DB4
2 PMD6/RE6 PMPD6 Display, JP1-13, DB6
3 PMD7/RE7 PMPD7 Display, JP1-14, DB7
4 SCK2/PMA5/CN8/RG6 SCK SD connector SCK, FLASH (U1) SCK*
5 SDI2/PMA4/CN9/RG7 SDI SD connector DO, FLASH (U1) SO*
6 SDO2/PMA3/CN10/RG8 SDO SD connector DI, FLASH (U1) SI*
7 MCLR\ PIC_MCLR Pulled high, J7-1, ICSP
8 SS2/PMA2/CN11/RG9 UTIL_CS FLASH (U1) CS*
9 Vss Grounded
10 Vdd +3.3V ---
11 AN5/C1IN+/Vbuson/CN7/RB5 Vbuson/AN5/RB5 To USB VBUS circuitry
12 AN4/C1IN-/CN6/RB4 SW_OK SW3, Pull high, low means SW3 closed
13 AN3/C2IN+/CN5/RB3 SW_UP SW1, Pull high, low means SW1 closed
14 AN2/C2IN-/CN4/RB2 SW_Down SW2, Pull high, low means SW2 closed
15 PGEC1/AN1/Vref-/CVref-/CN3/ ADC_SENSE_SWITCHED_+VBUS To USB VBUS circuitry
RB1
16 PGED1/AN0/VREF+/CVREF+/PMA6/ N/C Not connected
CN2/RB0
*FLASH (U1, SOIC) not populated
BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
17 PGEC2/AN6/OCFA/RB6 PIC_PGC2 J7-5, ICSP
18 PGED2/AN7/RB7 PIC_PGD2 J7-4, ICSP
19 AVdd +3.3V ---
20 AVss Grounded
21 AN8/U2CTS/C1OUT/RB8 N/C Not connected
22 AN9/C2OUT/PMA7/RB9 N/C Not connected
23 TMS/AN10/CVREFOUT/PMA13/RB10 UTIL_WP FLASH (U1) WP*
24 TDO/AN11/PMA12/RB11 SD_CS SD connector CS
25 Vss Grounded
26 Vdd +3.3V ---
27 TCK/AN12/PMA11/RB12 SD_CD SD connector CD
28 TDI/AN13/PMA10/RB13 SD_WD SD connector WD
29 AN14/U2RTS/PMALH/PMA1/RB14 N/C Not connected
30 AN15/OCFB/PMALL/PMA0/CN12/ PMPA0 Display, JP1-4, RS
RB15
31 SDA2/U2RX/PMA9/CN17/RF4 RXD2_MCU J5 DB9 via RS232 driver
32 SCL2/U2TX/PMA8/CN18/RF5 TXD2_MCU J5 DB9 via RS232 driver
*FLASH (U1, SOIC) not populated
RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
48 SOSCO/T1CK/CN0/RC14 SOSCO 32.768KHz XTAL (Y1)
47 SOSCI/CN1/RC13 SOSCI 32.768KHz XTAL (Y1)
46 OC1/INT0/RD0 PWM1 Used to control backlight level (K)
45 IC4/PMCS1/PMA14/INT4/RD11 PMPCS1 Display, JP1-6, E
44 SCL1/IC3/PMCS2/PMA15/INT3/ USB_OPT USB PHY
RD10
43 U1CTS/SDA1/IC2/INT2/RD9 USB_OPTEN USB PHY
42 RTCC/IC1/INT1/RD8 N/C Not connected
41 Vss Grounded
40 OSC2/CLKO/RC15 OSC2 20MHz XTAL (Y2)
39 OSC1/CLKI/RC12 OSC1 20MHz XTAL (Y2)
38 Vdd +3.3V ---
37 D+/RG2 APPS_D+ USB connectors via PHY
36 D-/RG3 APPS_D- USB connectors via PHY
35 Vusb +3.3V ---
34 Vbus VBUS_DEVICE_MODE Display, USB Mini-B, USB Type A, JP1-1, +5V
33 USBID/RF3 N/C Not connected
TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
64 PMPD4/RE4 PMPD4 Display, JP1-11, DB4
63 PMPD3/RE3 PMPD3 Display, JP1-10, DB3
62 PMPD2/RE2 PMPD2 Display, JP1-9, DB2
61 PMPD1/RE1 PMPD1 Display, JP1-8, DB1
60 PMPD0/RE0 PMPD0 Display, JP1-7, DB0
59 RF1 RF1 Low illuminates LED/R/ERR
58 RF0 RF0 Low illuminates LED/Y/flash
57 ENVREG ENVREG Pulled high
56 Vcap/Vddcore VDDCORE Capactors to ground
55 CN16/RD7 RD7 Low illuminates LED/Y/USB
54 CN15/RD6 RD6 Low illuminates LED/Y/SD
53 PMRD/CN14/RD5 PMPRD Display, JP1-5, R/W
52 OC5/IC5/PMWR/CN13/RD4 N/C Not connected
51 U1TX/OC4/RD3 CP2102_RXD J6-3, UART1 (also CP2102*)
50 U1RX/OC3/RD2 CP2102_TXD J6-2, UART1 (also CP2102*)
49 U1RTS/OC2/RD1 PWM2 Used to control backlight level (Vo)
*USB-to-UART bridge (U1, CP2102) not populated
DB-DP11212 PIC32 General Purpose Demo Board
-------------------------------------------
PIC32MX440F512H 64-Pin QFN (USB) Pin Out as used on the DB-DP11212 PIC32 General
Purpose Demo Board
LEFT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
1 PMD5/RE5 PMPD5 Display, JP1-12, DB5
2 PMD6/RE6 PMPD6 Display, JP1-13, DB6
3 PMD7/RE7 PMPD7 Display, JP1-14, DB7
4 SCK2/PMA5/CN8/RG6 SCK FLASH (U4) SCK*
5 SDI2/PMA4/CN9/RG7 SDI FLASH (U4) SO*
6 SDO2/PMA3/CN10/RG8 SDO FLASH (U4) SI*
7 MCLR\ PIC_MCLR Pulled high, J2-1, ICSP
8 SS2/PMA2/CN11/RG9 N/C Not connected
9 Vss Grounded
10 Vdd +3.3V ---
11 Vbuson/AN5/CN7/RB5 RB5 LCD SEG5 (F), U5-10
12 AN4/CN6/RB4 RB4 LCD SEG4 (E), U5-1
13 AN3/CN5/RB3 RB3 LCD SEG3 (D), U5-2
14 AN2/CN4/RB2 RB2 LCD SEG2 (C), U5-4
15 PGEC1/AN1/Vref-/CN3/RB1 RB1 LCD SEG1 (B), U5-7
16 PGED1/AN0/VREF+/CVREF+/PMA6/ RB0 LCD SEG0 (A), U5-11
CN2/RB0
*FLASH (U4, SOIC) not populated
BOTTOM SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
17 PGEC2/AN6/OCFA/RB6 PIC_PGC2 J2-5, ICSP
18 PGED2/AN7/RB7 PIC_PGD2 J2-4, ICSP
19 AVdd +3.3V ---
20 AVss Grounded
21 AN8/U2CTS/RB8 RB8 LCD SEG6 (G), U5-5
22 AN9/PMA7/RB9 RB9 LCD SEG7 (DP), U5-3
23 TMS/AN10/PMA13/RB10 UTIL_WP FLASH (U4) WP*
24 TDO/AN11/PMA12/RB11 UTIL_CS FLASH (U4) CS*
25 Vss Grounded
26 Vdd +3.3V ---
27 TCK/AN12/PMA11/RB12 N/C Not connected
28 TDI/AN13/PMA10/RB13 N/C Not connected
29 AN14/U2RTS/PMA1/RB14 temp_AD temp_AD
30 AN15/PMA0/CN12/RB15 PMPA0 Display, JP1-4, RS
31 SDA2/U2RX/PMA9/CN17/RF4 SDA LM75/SO, U3-1, SDA
32 SCL2/U2TX/PMA8/CN18/RF5 SCL LM75/SO, U3-2, SCL
*FLASH (U4, SOIC) not populated
RIGHT SIDE, TOP-TO-BOTTOM (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
48 SOSCO/T1CK/CN0/RC14 SOSCO 32.768KHz XTAL (Y1)
47 SOSCI/CN1/RC13 SOSCI 32.768KHz XTAL (Y1)
46 OC1/INT0/RD0 RD0 LCD DIG1, U5-12
45 IC4/PMCS1/PMA14/RD11 PMCS1 Display, JP1-6, E
44 SCL1/PMCS2/PMA15 RD10 LCD DIG2, U5-9
43 SDA1/RD9 RD9 LCD DIG3, U5-8
42 RTCC/RD8 RD8 LCD DIG4, U5-6
41 Vss Grounded
40 OSC2/CLKO/RC15 OSC2 20MHz XTAL (Y2)
39 OSC1/CLKI/RC12 OSC1 20MHz XTAL (Y2)
38 Vdd +3.3V ---
37 D+ MCU_D+ USB connectors via PHY
36 D- MCU_D- USB connectors via PHY
35 Vusb +3.3V ---
34 Vbus +5V_DUSB Display, USB Mini-B, USB Type A, JP1-1, +5V
33 USBID/RF3 N/C Not connected
TOP SIDE, LEFT-TO-RIGHT (if pin 1 is in upper left)
PIN NAME SIGNAL NOTES
---- ----------------------------- -------------- -------------------------------
64 PMPD4/RD4 PMPD4 Display, JP1-11, DB4
63 PMPD3/RD3 PMPD3 Display, JP1-10, DB3
62 PMPD2/RD2 PMPD2 Display, JP1-9, DB2
61 PMPD1/RD1 PMPD1 Display, JP1-8, DB1
60 PMPD0/RE0 PMPD0 Display, JP1-7, DB0
59 RF1 Key3 SW3-1
58 RF0 Key2 SW2-1
57 ENVREG ENVREG Pulled high
56 Vcap/Vddcore VDDCORE Capacitors to ground
55 CN16/RD7 N/C Not connected
54 CN15/RD6 Key5 SW5-1
53 PMRD/CN14/RD5 PMPRD ---
52 OC5/PMWR/CN13/RD4 PWM2 Used to control backlight level (Vo)
51 U1TX/OC4/RD3 N/C Not connected
50 U1RX/OC3/RD2 N/C Not connected
49 OC2/RD1 PWM1 Used to control backlight level (K)
Toolchains
==========
MPLAB/C32
---------
I am using the free, "Lite" version of the PIC32MX toolchain available
for download from the microchip.com web site. I am using the Windows
version. The MicroChip toolchain is the only toolchain currently
supported in these configurations, but it should be a simple matter to
adapt to other toolchains by modifying the Make.defs file include in
each configuration.
C32 Toolchain Options:
CONFIG_PIC32MX_MICROCHIPW - MicroChip full toolchain for Windows
CONFIG_PIC32MX_MICROCHIPL - MicroChip full toolchain for Linux
CONFIG_PIC32MX_MICROCHIPW_LITE - MicroChip "Lite" toolchain for Windows
CONFIG_PIC32MX_MICROCHIPL_LITE - MicroChip "Lite" toolchain for Linux
NOTE: The "Lite" versions of the toolchain does not support C++. Also
certain optimization levels are not supported by the "Lite" toolchain.
MicrochipOpen
-------------
An alternative, build-it-yourself toolchain is available here:
http://sourceforge.net/projects/microchipopen/ . These tools were
last updated circa 2010. NOTE: C++ support still not available
in this toolchain.
Building MicrochipOpen (on Linux)
1) Get the build script from this location:
http://microchipopen.svn.sourceforge.net/viewvc/microchipopen/ccompiler4pic32/buildscripts/trunk/
2) Build the code using the build script, for example:
./build.sh -b v105_freeze
This will check out the selected branch and build the tools.
3) Binaries will then be available in a subdirectory with a name something like
pic32-v105-freeze-20120622/install-image/bin (depending on the current data
and the branch that you selected.
Note that the tools will have the prefix, mypic32- so, for example, the
compiler will be called mypic32-gcc.
Penguino mips-elf Toolchain
---------------------------
Another option is the mips-elf toolchain used with the Penguino project. This
is a relatively current mips-elf GCC and should provide free C++ support as
well. This toolchain can be downloded from the Penguino website:
http://wiki.pinguino.cc/index.php/Main_Page#Download . There is some general
information about using the Penguino mips-elf toolchain in this thread:
http://tech.groups.yahoo.com/group/nuttx/message/1821
See also configs/mirtoo/README.txt. There is an experimental (untested)
configuration for the Mirtoo platform in that directory.
MPLAB/C32 vs MPLABX/X32
-----------------------
It appears that Microchip is phasing out the MPLAB/C32 toolchain and replacing
it with MPLABX and XC32. At present, the XC32 toolchain is *not* compatible
with the NuttX build scripts. Here are some of the issues that I see when trying
to build with XC32:
1) Make.def changes: You have to change the tool prefix:
CROSSDEV=xc32-
2) debug.ld/release.ld: The like expect some things that are not present in
the current linker scripts (or are expected with different names). Here
are some partial fixes:
Rename: kseg0_progmem to kseg0_program_mem
Rename: kseg1_datamem to kseg1_data_mem
Even then, there are more warnings from the linker and some undefined symbols
for non-NuttX code that resides in the unused Microchip libraries. See this
email thread at http://tech.groups.yahoo.com/group/nuttx/message/1458 for more
information. You will have to solve at least this undefined symbol problem if
you want to used the XC32 toolchain.
Windows Native Toolchains
-------------------------
NOTE: There are several limitations to using a Windows based toolchain in a
Cygwin environment. The three biggest are:
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had no effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:
make clean_context all
An alias in your .bashrc file might make that less painful.
3. Dependencies are not made when using Windows versions of the GCC. This is
because the dependencies are generated using Windows pathes which do not
work with the Cygwin make.
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
Loading NuttX with PICkit2
==========================
NOTE: You need a PICKit3 if you plan to use the MPLAB debugger! The PICKit2
can, however, still be used to load programs. Instructions for the PICKit3
are similar.
Intel Hex Forma Files:
----------------------
When NuttX is built it will produce two files in the top-level NuttX
directory:
1) nuttx - This is an ELF file, and
2) nuttx.hex - This is an Intel Hex format file. This is controlled by
the setting CONFIG_INTELHEX_BINARY in the .config file.
The PICkit tool wants an Intel Hex format file to burn into FLASH. However,
there is a problem with the generated nutt.hex: The tool expects the nuttx.hex
file to contain physical addresses. But the nuttx.hex file generated from the
top-level make will have address in the KSEG0 and KSEG1 regions.
tools/pic32mx/mkpichex:
----------------------
There is a simple tool in the NuttX tools/pic32mx directory that can be
used to solve both issues with the nuttx.hex file. But, first, you must
build the tool:
cd tools/pic32mx
make
Now you will have an excecutable file call mkpichex (or mkpichex.exe on
Cygwin). This program will take the nutt.hex file as an input, it will
convert all of the KSEG0 and KSEG1 addresses to physical address, and
it will write the modified file, replacing the original nuttx.hex.
To use this file, you need to do the following things:
. ./setenv.sh # Source setenv.sh. Among other this, this script
# will add the NuttX tools/pic32mx directory to your
# PATH variable
make # Build nuttx and nuttx.hex
mkpichex $PWD # Convert addresses in nuttx.hex. $PWD is the path
# to the top-level build directory. It is the only
# required input to mkpichex.
LCD1602
=======
The on-board LCD is a 2x16 segment LCD and appears to be compatible with
the LCD1602 and is like an LCD1602 LCD here.
LCD pin mapping (see configs/pcblogic-pic32mx/README.txt)
--------------------- ---------- ----------------------------------
PIC32 Sure JP1 Sure Signal Description
PIN SIGNAL NAME PIN NAME(s)
--------------------- ---------- ----------------------------------
34 Vbus 1. +5V +5V VBUS device mode
To GND via capacitor
2. GND GND
49 RD1 3. Vo Transistor circuit driven by PWM2
44 PMA0/AN15/RB15 4. RS PMA0, Selects registers
53 PMRD/RD5 5. RW PMRD/PMWR, Selects read or write
45 PMPCS1/RD11 6. E Starts data read/write
60 PMD0/RE0 7. DB0 PMD0
61 PMD1/RE1 8. DB1 PMD1
62 PMD2/RE2 9. DB2 PMD2
63 PMD3/RE3 10. DB3 PMD3
64 PMD4/RE4 11. DB4 PMD4
1 PMD5/RE5 12. DB5 PMD5
2 PMD6/RE6 13. DB6 PMD6
3 PMD7/RE7 14. DB7 PMD7
15. A +5V_DUSB
46 INT0/RD0 16. K Transistor circuit driven by PWM1
--------------------- ---------- ----------------------------------
Vbus power also requires Vbuson/AN5/RB5
PIC32MX Configuration Options
=============================
General Architecture Settings:
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=mips
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_MIPS=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_MIPS32=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP=pic32mx
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_PIC32MX440F512H=y
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=sure-pic32mx
CONFIG_ARCH_DBDP11215 Distinguishes the DB_DP11215 PIC32 Storage
Demo Board
CONFIG_ARCH_DBDP11212 Distingustes the DB-DP11212 PIC32 General
Purpose Demo Board
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_SUREPIC32MX=y
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case):
CONFIG_DRAM_SIZE=(32*1024) (32Kb)
There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1.
CONFIG_DRAM_START - The start address of installed DRAM
CONFIG_DRAM_START=0xa0000000
CONFIG_ARCH_IRQPRIO - The PIC32MXx supports interrupt prioritization
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
PIC32MX Configuration
CONFIG_PIC32MX_MVEC - Select muli- vs. single-vectored interrupts
Individual subsystems can be enabled:
CONFIG_PIC32MX_WDT - Watchdog timer
CONFIG_PIC32MX_T2 - Timer 2 (Timer 1 is the system time and always enabled)
CONFIG_PIC32MX_T3 - Timer 3
CONFIG_PIC32MX_T4 - Timer 4
CONFIG_PIC32MX_T5 - Timer 5
CONFIG_PIC32MX_IC1 - Input Capture 1
CONFIG_PIC32MX_IC2 - Input Capture 2
CONFIG_PIC32MX_IC3 - Input Capture 3
CONFIG_PIC32MX_IC4 - Input Capture 4
CONFIG_PIC32MX_IC5 - Input Capture 5
CONFIG_PIC32MX_OC1 - Output Compare 1
CONFIG_PIC32MX_OC2 - Output Compare 2
CONFIG_PIC32MX_OC3 - Output Compare 3
CONFIG_PIC32MX_OC4 - Output Compare 4
CONFIG_PIC32MX_OC5 - Output Compare 5
CONFIG_PIC32MX_I2C1 - I2C 1
CONFIG_PIC32MX_I2C2 - I2C 2
CONFIG_PIC32MX_SPI2 - SPI 2
CONFIG_PIC32MX_UART1 - UART 1
CONFIG_PIC32MX_UART2 - UART 2
CONFIG_PIC32MX_ADC - ADC 1
CONFIG_PIC32MX_PMP - Parallel Master Port
CONFIG_PIC32MX_CM1 - Comparator 1
CONFIG_PIC32MX_CM2 - Comparator 2
CONFIG_PIC32MX_RTCC - Real-Time Clock and Calendar
CONFIG_PIC32MX_DMA - DMA
CONFIG_PIC32MX_FLASH - FLASH
CONFIG_PIC32MX_USBDEV - USB device
CONFIG_PIC32MX_USBHOST - USB host
PIC32MX Configuration Settings
DEVCFG0:
CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The
value 2 enables.
CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select
Default 1 (PG2)
CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled)
CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled)
CONFIG_PIC32MX_CODEWP - Default 1 (disabled)
DEVCFG1: (All settings determined by selections in board.h)
DEVCFG2: (All settings determined by selections in board.h)
DEVCFG3:
CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled
(USBID pin is controlled by the USB module), but 0 (GPIO) otherwise.
CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled
(VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise.
CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog
can be enabled later by software).
The priority of interrupts may be specified. The value ranage of
priority is 4-31. The default (16) will be used if these any of these
are undefined.
CONFIG_PIC32MX_CTPRIO - Core Timer Interrupt
CONFIG_PIC32MX_CS0PRIO - Core Software Interrupt 0
CONFIG_PIC32MX_CS1PRIO - Core Software Interrupt 1
CONFIG_PIC32MX_INT0PRIO - External Interrupt 0
CONFIG_PIC32MX_INT1PRIO - External Interrupt 1
CONFIG_PIC32MX_INT2PRIO - External Interrupt 2
CONFIG_PIC32MX_INT3PRIO - External Interrupt 3
CONFIG_PIC32MX_INT4PRIO - External Interrupt 4
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
CONFIG_PIC32MX_T1PRIO - Timer 1 (System timer) priority
CONFIG_PIC32MX_T2PRIO - Timer 2 priority
CONFIG_PIC32MX_T3PRIO - Timer 3 priority
CONFIG_PIC32MX_T4PRIO - Timer 4 priority
CONFIG_PIC32MX_T5PRIO - Timer 5 priority
CONFIG_PIC32MX_IC1PRIO - Input Capture 1
CONFIG_PIC32MX_IC2PRIO - Input Capture 2
CONFIG_PIC32MX_IC3PRIO - Input Capture 3
CONFIG_PIC32MX_IC4PRIO - Input Capture 4
CONFIG_PIC32MX_IC5PRIO - Input Capture 5
CONFIG_PIC32MX_OC1PRIO - Output Compare 1
CONFIG_PIC32MX_OC2PRIO - Output Compare 2
CONFIG_PIC32MX_OC3PRIO - Output Compare 3
CONFIG_PIC32MX_OC4PRIO - Output Compare 4
CONFIG_PIC32MX_OC5PRIO - Output Compare 5
CONFIG_PIC32MX_I2C1PRIO - I2C 1
CONFIG_PIC32MX_I2C2PRIO - I2C 2
CONFIG_PIC32MX_SPI2PRIO - SPI 2
CONFIG_PIC32MX_UART1PRIO - UART 1
CONFIG_PIC32MX_UART2PRIO - UART 2
CONFIG_PIC32MX_CN - Input Change Interrupt
CONFIG_PIC32MX_ADCPRIO - ADC1 Convert Done
CONFIG_PIC32MX_PMPPRIO - Parallel Master Port
CONFIG_PIC32MX_CM1PRIO - Comparator 1
CONFIG_PIC32MX_CM2PRIO - Comparator 2
CONFIG_PIC32MX_FSCMPRIO - Fail-Safe Clock Monitor
CONFIG_PIC32MX_RTCCPRIO - Real-Time Clock and Calendar
CONFIG_PIC32MX_DMA0PRIO - DMA Channel 0
CONFIG_PIC32MX_DMA1PRIO - DMA Channel 1
CONFIG_PIC32MX_DMA2PRIO - DMA Channel 2
CONFIG_PIC32MX_DMA3PRIO - DMA Channel 3
CONFIG_PIC32MX_FCEPRIO - Flash Control Event
CONFIG_PIC32MX_USBPRIO - USB
PIC32MXx specific device driver settings. NOTE: For the Sure board,
UART2 is brought out to the DB9 connector and serves as the serial
console.
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
console and ttys0 (default is the UART0).
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_UARTn_2STOP - Two stop bits
PIC32MXx USB Device Configuration
PIC32MXx USB Host Configuration (the PIC32MX does not support USB Host)
Configurations
==============
Each PIC32MX configuration is maintained in a sub-directory and can be
selected as follow:
cd tools
./configure.sh sure-pic32mx/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following sub-directories.
NOTE: These configurations use the mconf-based configuration tool. To
change any of these configurations using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
and misc/tools/
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
Configuration sub-directories
-----------------------------
Where <subdir> is one of the following:
ostest:
=======
Description.
------------
This configuration directory, performs a simple OS test using
apps/examples/ostest.
Notes.
-----
1. By default, this configuration uses an older Microchip C32 toolchain
for Windows (the newer ones seem to be incompatible) and builds under
Cygwin (or probably MSYS). That
can easily be reconfigured, of course.
Build Setup:
CONFIG_HOST_WINDOWS=y : Builds under Windows
CONFIG_WINDOWS_CYGWIN=y : Using Cygwin
System Type:
CONFIG_MIPS32_TOOLCHAIN_MICROCHIPW_LITE=y : Older C32 toolchain
nsh:
====
Description.
------------
Configures the NuttShell (nsh) located at apps/examples/nsh. The
Configuration enables only the serial NSH interface.
Notes.
-----
1. By default, this configuration uses an older Microchip C32 toolchain
for Windows (the newer ones seem to be incompatible) and builds under
Cygwin (or probably MSYS). That can easily be reconfigured, of course.
Build Setup:
CONFIG_HOST_WINDOWS=y : Builds under Windows
CONFIG_WINDOWS_CYGWIN=y : Using Cygwin
System Type:
CONFIG_MIPS32_TOOLCHAIN_MICROCHIPW_LITE=y : Older C32 toolchain
2. USB Configuations.
Several USB device configurations can be enabled and included
as NSH built-in built in functions. All require the following
basic setup in your .config to enable USB device support:
Drivers:
CONFIG_USBDEV=y : Enable basic USB device support
System Type -> PIC32MX Peripheral Support:
CONFIG_PIC32MX_USBDEV=y : Enable PIC32 USB device support
examples/usbterm - This option can be enabled by uncommenting
the following line in the appconfig file:
Application Configuration->Examples:
CONFIG_EXAMPLES_USBTERM=y : Selects /apps/examples/usbterm
And by enabling one of the USB serial devices:
Drivers->USB Device Driver Support
CONFIG_PL2303=y : Enable the Prolifics PL2303 emulation
CONFIG_CDCACM=y : or the CDC/ACM serial driver (not both)
examples/cdcacm - The examples/cdcacm program can be included as an
function by uncommenting the following line in the appconfig file:
Application Configuration->Examples:
CONFIG_EXAMPLES_CDCACM=y : Select apps/examples/cdcacm
and defining the following in your .config file:
Drivers->USB Device Driver Support
CONFIG_CDCACM=y : Enable the CDCACM device
examples/usbstorage - There are some hooks in the appconfig file
to enable the USB mass storage class (MSC)device. However, this device
cannot work until support for the SD card is also incorporated.
Drivers->USB Device Driver Support
CONFIG_USBMSC=y : Enables the USB MSC class
Application Configuration->Examples:
CONFIG_EXAMPLES_USBSTORAGE=y : Enhables apps/examples/usbstorage
3. SD Card Support.
Support for the on-board, SPI-based SD card is available but is
not yet functional (at least at the time of this writing). SD
card support can be enabled for testing by simply enabling SPI2
support in the configuration file:
System Type -> PIC32MX Peripheral Support:
CONFIG_PIC32MX_SPI2=y : Enable SPI2
Drivers:
CONFIG_MMCSD=y : MMC/SD support
CONFIG_MMCSD_SPI=y : SPI-based MMC/SD support
File Systems:
CONFIG_FS_FAT=y : FAT file system
: Other FAT options
Debug output for testing the SD card can be enabled using:
Build Setup:
CONFIG_DEBUG=y : Enable debug features
CONFIG_DEBUG_VERBOSE=y : Enable verbose debug output
CONFIG_DEBUG_FS=y : Enable file system debug
CONFIG_DEBUG_SPI=y : Enable SPI debug
4. To enable LCD1602 support:
Device Drivers ->LCD Driver Support:
CONFIG_LCD=y : Enable LCD menus
CONFIG_LCD_LCD1602=y : Select LCD1602
CONFIG_LCD_MAXCONTRAST=255 : (Or any large-ish value that you prefer)
CONFIG_LCD_MAXPOWER=255 : (Or any large-ish value that you prefer)
Library Routines:
CONFIG_LIB_SLCDCODEC=y : Enable the SLCD CODEC
NOTE that is is not necessary to select the PMP peripheral; this LCD
driver is a bit-bang driver that just happens to use the PMP pins as
GPIOS.
To enable apps/examples/slcd to test the LCD:
Application Configuration -> NSH Library:
CONFIG_NSH_ARCHINIT=y : Needed to initialize the SLCD
Application Configuration -> Examples:
CONFIG_EXAMPLES_SLCD=y : Enable apps/examples/slcd use /dev/lcd1602
CONFIG_EXAMPLES_SLCD_DEVNAME="/dev/lcd1602"
To enable LCD debug output:
Build Setup -> Debug Options:
CONFIG_DEBUG=y : Enable debug features
CONFIG_DEBUG_VERBOSE=y : Enable verbose debug output
CONFIG_DEBUG_LCD=y : Enable LCD debug output
NOTES:
2013-05-27: The LCD1602 has been verified on the DB-DP11212 using
this configuration. It has not been used with the usbnsh configuration
or with the DB-11112 board. It looks to me like the connection to the
LCD1602 is identical on the DB-11112 and so I would expect that to work.
At this point in time, testing of the SLCD is very limited because
there is not much in apps/examples/slcd. Basically driver with a working
test setup and ready to be tested and debugged.
usbnsh:
=======
Description.
------------
This is another NSH example. If differs from the 'nsh' configuration
above in that this configurations uses a USB serial device for console
I/O. This configuration was created to support the "DB-DP11212 PIC32
General Purpose Demo Board" which has no easily accessible serial port.
However, as of this writing, the configuration has set for the
"DB_DP11215 PIC32 Storage Demo Board" and has only be testing on that
board.
Notes.
-----
1. By default, this configuration uses an older Microchip C32 toolchain
for Windows (the newer ones seem to be incompatible) and builds under
Cygwin (or probably MSYS). That can easily be reconfigured, of course.
Build Setup:
CONFIG_HOST_WINDOWS=y : Builds under Windows
CONFIG_WINDOWS_CYGWIN=y : Using Cygwin
System Type:
CONFIG_MIPS32_TOOLCHAIN_MICROCHIPW_LITE=y : Older C32 toolchain
2. Comparison to nsh
Below summarizes the key configuration differences between the 'nsh'
and the 'upnsh' configurations:
CONFIG_USBDEV=y : NuttX USB device support is enabled
CONFIG_PIC32MX_USBDEV=y : The PIC32MX USB device driver is built
CONFIG_DEV_CONSOLE=n : /dev/console does not exist on power up
CONFIG_UART1_SERIAL_CONSOLE=n : There is no serial console
CONFIG_UART2_SERIAL_CONSOLE=n :
CONFIG_CDCACM=y : The CDC/ACM serial device class is enabled
CONFIG_CDCACM_CONSOLE=y : The CDC/ACM serial device is the console
3. Using the Prolifics PL2303 Emulation
You could also use the non-standard PL2303 serial device instead of
the standard CDC/ACM serial device by changing:
Drivers->USB Device Driver Support
CONFIG_CDCACM=n : Disable the CDC/ACM serial device class
CONFIG_CDCACM_CONSOLE=n : The CDC/ACM serial device is NOT the console
CONFIG_PL2303=y : The Prolifics PL2303 emulation is enabled
CONFIG_PL2303_CONSOLE=y : The PL2303 serial device is the console
Why would you want to use a non-standard USB serial driver? You might
to use the PL2303 driver with a Windows host because it should
automatically install the PL2303 driver (you might have to go through
some effort to get Windows to recognize the CDC/ACM device).
4. Since this configuration is current set for the "DB_DP11215 PIC32
Storage Demo Board," UART2 is available and is configured to used as
the SYSLOG device. That means that all debug output will be directed
out UART2. Debug output is not enabled by default, however, so these
settings do nothing until you enable debug ouput.
Device Drivers -> System Logging Device Options:
CONFIG_SYSLOG=y : Configure SYSLOG output
CONFIG_SYSLOG_CHAR=y
CONFIG_SYSLOG_DEVPATH="/dev/ttyS0"
System Type -> PIC32MX Peripheral Support:
CONFIG_PIC32MX_UART2=y : Enable UART2
Device Drivers -> Serial Driver Support:
CONFIG_UART2_2STOP=0 : UART2 configuration
CONFIG_UART2_BAUD=115200
CONFIG_UART2_BITS=8
CONFIG_UART2_PARITY=0
CONFIG_UART2_RXBUFSIZE=64
CONFIG_UART2_TXBUFSIZE=64
NOTE: Using the SYSLOG to get debug output has limitations. Among
those are that you cannot get debug output from interrupt handlers.
So, in particularly, debug output is not a useful way to debug the
USB device controller driver. Instead, use the USB monitor with
USB debug off and USB trance on (see below).
5. Enabling USB monitor SYSLOG output. If tracing is enabled, the USB
device will save encoded trace output in in-memory buffer; if the
USB monitor is enabled, that trace buffer will be periodically
emptied and dumped to the system logging device (UART2 in this
configuration):
Device Drivers -> "USB Device Driver Support:
CONFIG_USBDEV_TRACE=y : Enable USB trace feature
CONFIG_USBDEV_TRACE_NRECORDS=256 : Buffer 128 records in memory
Application Configuration -> NSH LIbrary:
CONFIG_NSH_USBDEV_TRACE=n : No builtin tracing from NSH
CONFIG_NSH_ARCHINIT=y : Automatically start the USB monitor
Application Configuration -> System NSH Add-Ons:
CONFIG_SYSTEM_USBMONITOR=y : Enable the USB monitor daemon
CONFIG_SYSTEM_USBMONITOR_STACKSIZE=2048 : USB monitor daemon stack size
CONFIG_SYSTEM_USBMONITOR_PRIORITY=50 : USB monitor daemon priority
CONFIG_SYSTEM_USBMONITOR_INTERVAL=1 : Dump trace data every second
CONFIG_SYSTEM_USBMONITOR_TRACEINIT=y : Enable TRACE output
CONFIG_SYSTEM_USBMONITOR_TRACECLASS=y
CONFIG_SYSTEM_USBMONITOR_TRACETRANSFERS=y
CONFIG_SYSTEM_USBMONITOR_TRACECONTROLLER=y
CONFIG_SYSTEM_USBMONITOR_TRACEINTERRUPTS=y
NOTE: USB debug output also be enabled in this case. Both will appear
on the serial SYSLOG output. However, the debug output will be
asynchronous with the trace output and, hence, difficult to interpret.
6. If you want to try this configuration on the DB-DP11212 PIC32 General
Purpose Demo Board", here are the changes that you should make:
Board Configuration:
CONFIG_ARCH_DBDP11215=n : Disable the DB-DP11215
CONFIG_ARCH_DBDP11212=y : Enable the DB-DP11212
CONFIG_ARCH_LEDS=n : The DB-DP11212 has no LEDs
System Type -> PIC32MX Peripheral Support:
CONFIG_PIC32MX_UART2=n : Disable UART2
The SYSLOG output on UART2 cannot by used. You have two choices,
first, you can simply disable the SYSLOG device. Then 1) debug
output will come the USB console, and 2) all debug output prior
to connecting the USB console will be lost:
Device Drivers -> System Logging Device Options:
CONFIG_SYSLOG=n : Disable SYSLOG output
The second options is to configure a RAM SYLOG device. This is
a circular buffer that accumulated debug output in memory. The
contents of the circular buffer can be dumped from the NSH command
line using the 'dmesg' command.
Device Drivers -> System Logging Device Options:
CONFIG_SYSLOG=y : Enables the System Logging feature.
CONFIG_RAMLOG=y : Enable the RAM-based logging feature.
CONFIG_RAMLOG_CONSOLE=n : (there is no default console device)
CONFIG_RAMLOG_SYSLOG=y : This enables the RAM-based logger as the
system logger.
Logging is currently can be set up to use any amount of memory (here 8KB):
CONFIG_RAMLOG_CONSOLE_BUFSIZE=8192
STATUS:
2013-7-4: This configuration was last verified.
7. See the notes for the nsh configuration. Most also apply to the usbnsh
configuration as well.
|