1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
|
#
# For a description of the syntax of this configuration file,
# see misc/tools/kconfig-language.txt.
#
config NET_DM90x0
bool "Davicom dm9000/dm9010 support"
default n
---help---
References: Davicom data sheets (DM9000-DS-F03-041906.pdf,
DM9010-DS-F01-103006.pdf) and looking at lots of other DM90x0
drivers.
config NET_CS89x0
bool "CS89x0 support"
default n
depends on EXPERIMENTAL
---help---
Under construction -- do not use
config ENC28J60
bool "Microchip ENC28J60 support"
default n
select SPI
---help---
References:
ENC28J60 Data Sheet, Stand-Alone Ethernet Controller with SPI Interface,
DS39662C, 2008 Microchip Technology Inc.
if ENC28J60
config ENC28J60_NINTERFACES
int "Number of physical ENC28J60"
default 1
range 1,1
---help---
Specifies the number of physical ENC28J60
devices that will be supported.
config ENC28J60_SPIMODE
int "SPI mode"
default 0
---help---
Controls the SPI mode. The ENC28J60 spec says that it supports SPI
mode 0,0 only: "The implementation used on this device supports SPI
mode 0,0 only. In addition, the SPI port requires that SCK be at Idle
in a low state; selectable clock polarity is not supported."
However, sometimes you need to tinker with these things.
config ENC28J60_FREQUENCY
int "SPI frequency"
default 20000000
---help---
Define to use a different bus frequency
config ENC28J60_STATS
bool "Network statistics support"
default n
---help---
Collect network statistics
config ENC28J60_HALFDUPPLEX
bool "Enable half dupplex"
default n
---help---
Default is full duplex
config ENC28J60_DUMPPACKET
bool "Dump Packets"
default n
---help---
If selected, the ENC28J60 driver will dump the contents of each
packet to the console.
config ENC28J60_REGDEBUG
bool "Register-Level Debug"
default n
depends on DEBUG && DEBUG_NET
---help---
Enable very low-level register access debug. Depends on DEBUG and DEBUG_NET.
endif
config ENCX24J600
bool "Microchip ENCX24J600 support"
default n
select SPI
---help---
References:
ENC424J600/624J600 Data Sheet Stand-Alone 10/100 Ethernet Controller
with SPI or Parallel Interface DS39935B, 2009 Microchip Technology Inc.
if ENCX24J600
config ENC28J60_NINTERFACES
int "Number of physical ENCX24J600"
default 1
range 1,1
---help---
Specifies the number of physical ENCX24J600
devices that will be supported.
config ENCX24J600_SPIMODE
int "SPI mode"
default 0
---help---
Controls the SPI mode. The ENCX24J600 spec says that it supports SPI
mode 0,0 only: "The implementation used on this device supports SPI
mode 0,0 only. In addition, the SPI port requires that SCK be at Idle
in a low state; selectable clock polarity is not supported."
However, sometimes you need to tinker with these things.
config ENCX24J600_FREQUENCY
int "SPI frequency"
default 14000000
---help---
Define to use a different bus frequency
config ENCX24J600_STATS
bool "Network statistics support"
default n
---help---
Collect network statistics
config ENCX24J600_DUMPPACKET
bool "Dump Packets"
default n
---help---
If selected, the ENCX24J600 driver will dump the contents of each
packet to the console.
config ENCX24J600_REGDEBUG
bool "Register-Level Debug"
default n
depends on DEBUG && DEBUG_NET
---help---
Enable very low-level register access debug. Depends on DEBUG and DEBUG_NET.
endif
config NET_E1000
bool "E1000 support"
default n
config NET_SLIP
bool "SLIP (serial line) support"
default n
---help---
Reference: RFC 1055
config NET_VNET
bool "VNET support"
default n
|
