diff options
Diffstat (limited to 'dev/arduino-terminal/ext/arduino/core/CDC.cpp')
| -rw-r--r-- | dev/arduino-terminal/ext/arduino/core/CDC.cpp | 208 |
1 files changed, 208 insertions, 0 deletions
diff --git a/dev/arduino-terminal/ext/arduino/core/CDC.cpp b/dev/arduino-terminal/ext/arduino/core/CDC.cpp new file mode 100644 index 0000000..aae91c2 --- /dev/null +++ b/dev/arduino-terminal/ext/arduino/core/CDC.cpp @@ -0,0 +1,208 @@ + + +/* Copyright (c) 2011, Peter Barrett +** +** Permission to use, copy, modify, and/or distribute this software for +** any purpose with or without fee is hereby granted, provided that the +** above copyright notice and this permission notice appear in all copies. +** +** THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL +** WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED +** WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR +** BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES +** OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, +** WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, +** ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS +** SOFTWARE. +*/ + +#include "Platform.h" +#include "USBAPI.h" +#include <avr/wdt.h> + +#if defined(USBCON) +#ifdef CDC_ENABLED + +typedef struct +{ + u32 dwDTERate; + u8 bCharFormat; + u8 bParityType; + u8 bDataBits; + u8 lineState; +} LineInfo; + +static volatile LineInfo _usbLineInfo = { 57600, 0x00, 0x00, 0x00, 0x00 }; + +#define WEAK __attribute__ ((weak)) + +extern const CDCDescriptor _cdcInterface PROGMEM; +const CDCDescriptor _cdcInterface = +{ + D_IAD(0,2,CDC_COMMUNICATION_INTERFACE_CLASS,CDC_ABSTRACT_CONTROL_MODEL,1), + + // CDC communication interface + D_INTERFACE(CDC_ACM_INTERFACE,1,CDC_COMMUNICATION_INTERFACE_CLASS,CDC_ABSTRACT_CONTROL_MODEL,0), + D_CDCCS(CDC_HEADER,0x10,0x01), // Header (1.10 bcd) + D_CDCCS(CDC_CALL_MANAGEMENT,1,1), // Device handles call management (not) + D_CDCCS4(CDC_ABSTRACT_CONTROL_MANAGEMENT,6), // SET_LINE_CODING, GET_LINE_CODING, SET_CONTROL_LINE_STATE supported + D_CDCCS(CDC_UNION,CDC_ACM_INTERFACE,CDC_DATA_INTERFACE), // Communication interface is master, data interface is slave 0 + D_ENDPOINT(USB_ENDPOINT_IN (CDC_ENDPOINT_ACM),USB_ENDPOINT_TYPE_INTERRUPT,0x10,0x40), + + // CDC data interface + D_INTERFACE(CDC_DATA_INTERFACE,2,CDC_DATA_INTERFACE_CLASS,0,0), + D_ENDPOINT(USB_ENDPOINT_OUT(CDC_ENDPOINT_OUT),USB_ENDPOINT_TYPE_BULK,0x40,0), + D_ENDPOINT(USB_ENDPOINT_IN (CDC_ENDPOINT_IN ),USB_ENDPOINT_TYPE_BULK,0x40,0) +}; + +int WEAK CDC_GetInterface(u8* interfaceNum) +{ + interfaceNum[0] += 2; // uses 2 + return USB_SendControl(TRANSFER_PGM,&_cdcInterface,sizeof(_cdcInterface)); +} + +bool WEAK CDC_Setup(Setup& setup) +{ + u8 r = setup.bRequest; + u8 requestType = setup.bmRequestType; + + if (REQUEST_DEVICETOHOST_CLASS_INTERFACE == requestType) + { + if (CDC_GET_LINE_CODING == r) + { + USB_SendControl(0,(void*)&_usbLineInfo,7); + return true; + } + } + + if (REQUEST_HOSTTODEVICE_CLASS_INTERFACE == requestType) + { + if (CDC_SET_LINE_CODING == r) + { + USB_RecvControl((void*)&_usbLineInfo,7); + return true; + } + + if (CDC_SET_CONTROL_LINE_STATE == r) + { + _usbLineInfo.lineState = setup.wValueL; + + // auto-reset into the bootloader is triggered when the port, already + // open at 1200 bps, is closed. this is the signal to start the watchdog + // with a relatively long period so it can finish housekeeping tasks + // like servicing endpoints before the sketch ends + if (1200 == _usbLineInfo.dwDTERate) { + // We check DTR state to determine if host port is open (bit 0 of lineState). + if ((_usbLineInfo.lineState & 0x01) == 0) { + *(uint16_t *)0x0800 = 0x7777; + wdt_enable(WDTO_120MS); + } else { + // Most OSs do some intermediate steps when configuring ports and DTR can + // twiggle more than once before stabilizing. + // To avoid spurious resets we set the watchdog to 250ms and eventually + // cancel if DTR goes back high. + + wdt_disable(); + wdt_reset(); + *(uint16_t *)0x0800 = 0x0; + } + } + return true; + } + } + return false; +} + + +void Serial_::begin(unsigned long baud_count) +{ + peek_buffer = -1; +} + +void Serial_::begin(unsigned long baud_count, byte config) +{ + peek_buffer = -1; +} + +void Serial_::end(void) +{ +} + +int Serial_::available(void) +{ + if (peek_buffer >= 0) { + return 1 + USB_Available(CDC_RX); + } + return USB_Available(CDC_RX); +} + +int Serial_::peek(void) +{ + if (peek_buffer < 0) + peek_buffer = USB_Recv(CDC_RX); + return peek_buffer; +} + +int Serial_::read(void) +{ + if (peek_buffer >= 0) { + int c = peek_buffer; + peek_buffer = -1; + return c; + } + return USB_Recv(CDC_RX); +} + +void Serial_::flush(void) +{ + USB_Flush(CDC_TX); +} + +size_t Serial_::write(uint8_t c) +{ + return write(&c, 1); +} + +size_t Serial_::write(const uint8_t *buffer, size_t size) +{ + /* only try to send bytes if the high-level CDC connection itself + is open (not just the pipe) - the OS should set lineState when the port + is opened and clear lineState when the port is closed. + bytes sent before the user opens the connection or after + the connection is closed are lost - just like with a UART. */ + + // TODO - ZE - check behavior on different OSes and test what happens if an + // open connection isn't broken cleanly (cable is yanked out, host dies + // or locks up, or host virtual serial port hangs) + if (_usbLineInfo.lineState > 0) { + int r = USB_Send(CDC_TX,buffer,size); + if (r > 0) { + return r; + } else { + setWriteError(); + return 0; + } + } + setWriteError(); + return 0; +} + +// This operator is a convenient way for a sketch to check whether the +// port has actually been configured and opened by the host (as opposed +// to just being connected to the host). It can be used, for example, in +// setup() before printing to ensure that an application on the host is +// actually ready to receive and display the data. +// We add a short delay before returning to fix a bug observed by Federico +// where the port is configured (lineState != 0) but not quite opened. +Serial_::operator bool() { + bool result = false; + if (_usbLineInfo.lineState > 0) + result = true; + delay(10); + return result; +} + +Serial_ Serial; + +#endif +#endif /* if defined(USBCON) */ |