|
|
/********************************************************************************************
* drivers/mmcsd/mmcsd_sdio.h
*
* Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
********************************************************************************************/
#ifndef __DRIVERS_MMCSD_MMCSD_SDIO_H
#define __DRIVERS_MMCSD_MMCSD_SDIO_H
/********************************************************************************************
* Included Files
********************************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
/********************************************************************************************
* Pre-Processor Definitions
********************************************************************************************/
/* CMD8 Argument:
* [31:12]: Reserved (shall be set to '0')
* [11:8]: Supply Voltage (VHS) 0x1 (Range: 2.7-3.6 V)
* [7:0]: Check Pattern (recommended 0xaa)
* CMD8 Response: R7
*/
#define MMCSD_CMD8VOLTAGE_SHIFT (8) /* Bits 8-11: Supply voltage */
#define MMCSD_CMD8VOLTAGE_MASK ((uint32_t)0x0f << MMCSD_CMD8VOLTAGE_SHIFT)
# define MMCSD_CMD8VOLTAGE_27 ((uint32_t)0x01 << MMCSD_CMD8VOLTAGE_SHIFT) /* 2.7-3.6V */
#define MMCSD_CMD8ECHO_SHIFT (0) /* Bits 0-7: Check pattern */
#define MMCSD_CMD8ECHO_MASK ((uint32_t)0xff << MMCSD_CMD8ECHO_SHIFT)
# define MMCSD_CMD8CHECKPATTERN ((uint32_t)0xaa << MMCSD_CMD8ECHO_SHIFT)
/* ACMD6 argument */
#define MMCSD_ACMD6_BUSWIDTH_1 ((uint32_t)0) /* Bus width = 1-bit */
#define MMCSD_ACMD6_BUSWIDTH_4 ((uint32_t)2) /* Bus width = 4-bit */
/* ACMD41 argument */
#define MMCSD_ACMD41_VOLTAGEWINDOW_34_33 ((uint32_t)1 << 21)
#define MMCSD_ACMD41_VOLTAGEWINDOW_33_32 ((uint32_t)1 << 20)
#define MMCSD_ACMD41_VOLTAGEWINDOW_32_31 ((uint32_t)1 << 19)
#define MMCSD_ACMD41_HIGHCAPACITY ((uint32_t)1 << 30)
#define MMCSD_ACMD41_STDCAPACITY ((uint32_t)0)
/* ACMD42 argument */
#define MMCSD_ACMD42_CD_DISCONNECT ((uint32_t)0) /* Disconnect card detection logic */
#define MMCSD_ACMD42_CD_CONNECT ((uint32_t)1) /* Connect card detection logic */
/* R1 Card Status bit definitions */
#define MMCSD_R1_OUTOFRANGE ((uint32_t)1 << 31) /* Bad argument */
#define MMCSD_R1_ADDRESSERROR ((uint32_t)1 << 30) /* Bad address */
#define MMCSD_R1_BLOCKLENERROR ((uint32_t)1 << 29) /* Bad block length */
#define MMCSD_R1_ERASESEQERROR ((uint32_t)1 << 28) /* Erase cmd error */
#define MMCSD_R1_ERASEPARAM ((uint32_t)1 << 27) /* Bad write blocks */
#define MMCSD_R1_WPVIOLATION ((uint32_t)1 << 26) /* Erase access failure */
#define MMCSD_R1_CARDISLOCKED ((uint32_t)1 << 25) /* Card is locked */
#define MMCSD_R1_LOCKUNLOCKFAILED ((uint32_t)1 << 24) /* Password error */
#define MMCSD_R1_COMCRCERROR ((uint32_t)1 << 23) /* CRC error */
#define MMCSD_R1_ILLEGALCOMMAND ((uint32_t)1 << 22) /* Bad command */
#define MMCSD_R1_CARDECCFAILED ((uint32_t)1 << 21) /* Failed to correct data */
#define MMCSD_R1_CCERROR ((uint32_t)1 << 20) /* Card controller error */
#define MMCSD_R1_ERROR ((uint32_t)1 << 19) /* General error */
#define MMCSD_R1_UNDERRUN ((uint32_t)1 << 18) /* Underrun (MMC only) */
#define MMCSD_R1_OVERRRUN ((uint32_t)1 << 17) /* Overrun (MMC only) */
#define MMCSD_R1_CIDCSDOVERWRITE ((uint32_t)1 << 16) /* CID/CSD error */
#define MMCSD_R1_WPERASESKIP ((uint32_t)1 << 15) /* Not all erased */
#define MMCSD_R1_CARDECCDISABLED ((uint32_t)1 << 14) /* Internal ECC not used */
#define MMCSD_R1_ERASERESET ((uint32_t)1 << 13) /* Reset sequence cleared */
#define MMCSD_R1_STATE_SHIFT (9) /* Current card state */
#define MMCSD_R1_STATE_MASK ((uint32_t)15 << MMCSD_R1_STATE_SHIFT)
/* Card identification mode states */
# define MMCSD_R1_STATE_IDLE ((uint32_t)0 << MMCSD_R1_STATE_SHIFT) /* 0=Idle state */
# define MMCSD_R1_STATE_READY ((uint32_t)1 << MMCSD_R1_STATE_SHIFT) /* 1=Ready state */
# define MMCSD_R1_STATE_IDENT ((uint32_t)2 << MMCSD_R1_STATE_SHIFT) /* 2=Identification state */
/* Data transfer states */
# define MMCSD_R1_STATE_STBY ((uint32_t)3 << MMCSD_R1_STATE_SHIFT) /* 3=Standby state */
# define MMCSD_R1_STATE_TRAN ((uint32_t)4 << MMCSD_R1_STATE_SHIFT) /* 4=Transfer state */
# define MMCSD_R1_STATE_DATA ((uint32_t)5 << MMCSD_R1_STATE_SHIFT) /* 5=Sending data state */
# define MMCSD_R1_STATE_RCV ((uint32_t)6 << MMCSD_R1_STATE_SHIFT) /* 6=Receiving data state */
# define MMCSD_R1_STATE_PRG ((uint32_t)7 << MMCSD_R1_STATE_SHIFT) /* 7=Programming state */
# define MMCSD_R1_STATE_DIS ((uint32_t)8 << MMCSD_R1_STATE_SHIFT) /* 8=Disconnect state */
#define MMCSD_R1_READYFORDATA ((uint32_t)1 << 8) /* Buffer empty */
#define MMCSD_R1_APPCMD ((uint32_t)1 << 5) /* Next CMD is ACMD */
#define MMCSD_R1_AKESEQERROR ((uint32_t)1 << 3) /* Authentication error */
#define MMCSD_R1_ERRORMASK ((uint32_t)0xfdffe008) /* Error mask */
#define IS_STATE(v,s) ((((uint32_t)v)&MMCSD_R1_STATE_MASK)==(s))
/* R3 (OCR) */
#define MMC_VDD_20_36 ((uint32_t)0x00ffff00) /* VDD voltage 2.0-3.6 */
#define MMCSD_VDD_145_150 ((uint32_t)1 << 0) /* VDD voltage 1.45 - 1.50 */
#define MMCSD_VDD_150_155 ((uint32_t)1 << 1) /* VDD voltage 1.50 - 1.55 */
#define MMCSD_VDD_155_160 ((uint32_t)1 << 2) /* VDD voltage 1.55 - 1.60 */
#define MMCSD_VDD_160_165 ((uint32_t)1 << 3) /* VDD voltage 1.60 - 1.65 */
#define MMCSD_VDD_165_170 ((uint32_t)1 << 4) /* VDD voltage 1.65 - 1.70 */
#define MMCSD_VDD_17_18 ((uint32_t)1 << 5) /* VDD voltage 1.7 - 1.8 */
#define MMCSD_VDD_18_19 ((uint32_t)1 << 6) /* VDD voltage 1.8 - 1.9 */
#define MMCSD_VDD_19_20 ((uint32_t)1 << 7) /* VDD voltage 1.9 - 2.0 */
#define MMCSD_VDD_20_21 ((uint32_t)1 << 8) /* VDD voltage 2.0-2.1 */
#define MMCSD_VDD_21_22 ((uint32_t)1 << 9) /* VDD voltage 2.1-2.2 */
#define MMCSD_VDD_22_23 ((uint32_t)1 << 10) /* VDD voltage 2.2-2.3 */
#define MMCSD_VDD_23_24 ((uint32_t)1 << 11) /* VDD voltage 2.3-2.4 */
#define MMCSD_VDD_24_25 ((uint32_t)1 << 12) /* VDD voltage 2.4-2.5 */
#define MMCSD_VDD_25_26 ((uint32_t)1 << 13) /* VDD voltage 2.5-2.6 */
#define MMCSD_VDD_26_27 ((uint32_t)1 << 14) /* VDD voltage 2.6-2.7 */
#define MMCSD_VDD_27_28 ((uint32_t)1 << 15) /* VDD voltage 2.7-2.8 */
#define MMCSD_VDD_28_29 ((uint32_t)1 << 16) /* VDD voltage 2.8-2.9 */
#define MMCSD_VDD_29_30 ((uint32_t)1 << 17) /* VDD voltage 2.9-3.0 */
#define MMCSD_VDD_30_31 ((uint32_t)1 << 18) /* VDD voltage 3.0-3.1 */
#define MMCSD_VDD_31_32 ((uint32_t)1 << 19) /* VDD voltage 3.1-3.2 */
#define MMCSD_VDD_32_33 ((uint32_t)1 << 20) /* VDD voltage 3.2-3.3 */
#define MMCSD_VDD_33_34 ((uint32_t)1 << 21) /* VDD voltage 3.3-3.4 */
#define MMCSD_VDD_34_35 ((uint32_t)1 << 22) /* VDD voltage 3.4-3.5 */
#define MMCSD_VDD_35_36 ((uint32_t)1 << 23) /* VDD voltage 3.5-3.6 */
#define MMCSD_R3_HIGHCAPACITY ((uint32_t)1 << 30) /* true: Card supports block addressing */
#define MMCSD_CARD_BUSY ((uint32_t)1 << 31) /* Card power-up busy bit */
/* R6 Card Status bit definitions */
#define MMCSD_R6_RCA_SHIFT (16) /* New published RCA */
#define MMCSD_R6_RCA_MASK ((uint32_t)0xffff << MMCSD_R6_RCA_SHIFT)
#define MMCSD_R6_COMCRCERROR ((uint32_t)1 << 15) /* CRC error */
#define MMCSD_R6_ILLEGALCOMMAND ((uint32_t)1 << 14) /* Bad command */
#define MMCSD_R6_ERROR ((uint32_t)1 << 13) /* General error */
#define MMCSD_R6_STATE_SHIFT (9) /* Current card state */
#define MMCSD_R6_STATE_MASK ((uint32_t)15 << MMCSD_R6_STATE_SHIFT)
/* Card identification mode states */
# define MMCSD_R6_STATE_IDLE ((uint32_t)0 << MMCSD_R6_STATE_SHIFT) /* 0=Idle state */
# define MMCSD_R6_STATE_READY ((uint32_t)1 << MMCSD_R6_STATE_SHIFT) /* 1=Ready state */
# define MMCSD_R6_STATE_IDENT ((uint32_t)2 << MMCSD_R6_STATE_SHIFT) /* 2=Identification state */
/* Data transfer states */
# define MMCSD_R6_STATE_STBY ((uint32_t)3 << MMCSD_R6_STATE_SHIFT) /* 3=Standby state */
# define MMCSD_R6_STATE_TRAN ((uint32_t)4 << MMCSD_R6_STATE_SHIFT) /* 4=Transfer state */
# define MMCSD_R6_STATE_DATA (5(uint32_t) << MMCSD_R6_STATE_SHIFT) /* 5=Sending data state */
# define MMCSD_R6_STATE_RCV ((uint32_t)6 << MMCSD_R6_STATE_SHIFT) /* 6=Receiving data state */
# define MMCSD_R6_STATE_PRG ((uint32_t)7 << MMCSD_R6_STATE_SHIFT) /* 7=Programming state */
# define MMCSD_R6_STATE_DIS ((uint32_t) << MMCSD_R6_STATE_SHIFT) /* 8=Disconnect state */
#define MMCSD_R6_ERRORMASK ((uint32_t)0x0000e000) /* Error mask */
/* SD Configuration Register (SCR) encoding */
#define MMCSD_SCR_BUSWIDTH_1BIT (1)
#define MMCSD_SCR_BUSWIDTH_2BIT (2)
#define MMCSD_SCR_BUSWIDTH_4BIT (4)
#define MMCSD_SCR_BUSWIDTH_8BIT (8)
/* Last 4 bytes of the 48-bit R7 response */
#define MMCSD_R7VERSION_SHIFT (28) /* Bits 28-31: Command version number */
#define MMCSD_R7VERSION_MASK ((uint32_t)0x0f << MMCSD_R7VERSION_SHIFT)
#define MMCSD_R7VOLTAGE_SHIFT (8) /* Bits 8-11: Voltage accepted */
#define MMCSD_R7VOLTAGE_MASK ((uint32_t)0x0f << MMCSD_R7VOLTAGE_SHIFT)
# define MMCSD_R7VOLTAGE_27 ((uint32_t)0x01 << MMCSD_R7VOLTAGE_SHIFT) /* 2.7-3.6V */
#define MMCSD_R7ECHO_SHIFT (0) /* Bits 0-7: Echoed check pattern */
#define MMCSD_R7ECHO_MASK ((uint32_t)0xff << MMCSD_R7ECHO_SHIFT)
# define MMCSD_R7CHECKPATTERN ((uint32_t)0xaa << MMCSD_R7ECHO_SHIFT)
/********************************************************************************************
* Public Types
********************************************************************************************/
/* Decoded Card Identification (CID) register */
struct mmcsd_cid_s
{
uint8_t mid; /* 127:120 8-bit Manufacturer ID */
uint16_t oid; /* 119:104 16-bit OEM/Application ID (ascii) */
uint8_t pnm[6]; /* 103:64 40-bit Product Name (ascii) + null terminator */
uint8_t prv; /* 63:56 8-bit Product revision */
uint32_t psn; /* 55:24 32-bit Product serial number */
/* 23:20 4-bit (reserved) */
uint16_t mdt; /* 19:8 12-bit Manufacturing date */
uint8_t crc; /* 7:1 7-bit CRC7 */
/* 0:0 1-bit (not used) */
};
/* Decoded Card Specific Data (CSD) register */
struct mmcsd_csd_s
{
uint8_t csdstructure; /* 127:126 CSD structure */
uint8_t mmcspecvers; /* 125:122 MMC Spec version (MMC only) */
struct
{
uint8_t timeunit; /* 2:0 Time exponent */
uint8_t timevalue; /* 6:3 Time mantissa */
} taac; /* 119:112 Data read access-time-1 */
uint8_t nsac; /* 111:104 Data read access-time-2 in CLK cycle(NSAC*100) */
struct
{
uint8_t transferrateunit; /* 2:0 Rate exponent */
uint8_t timevalue; /* 6:3 Rate mantissa */
} transpeed; /* 103:96 Max. data transfer rate */
uint16_t ccc; /* 95:84 Card command classes */
uint8_t readbllen; /* 83:80 Max. read data block length */
uint8_t readblpartial; /* 79:79 Partial blocks for read allowed */
uint8_t writeblkmisalign; /* 78:78 Write block misalignment */
uint8_t readblkmisalign; /* 77:77 Read block misalignment */
uint8_t dsrimp; /* 76:76 DSR implemented */
union
{
#ifdef CONFIG_MMCSD_MMCSUPPORT
struct
{
uint16_t csize; /* 73:62 Device size */
uint8_t vddrcurrmin; /* 61:59 Max. read current at Vdd min */
uint8_t vddrcurrmax; /* 58:56 Max. read current at Vdd max */
uint8_t vddwcurrmin; /* 55:53 Max. write current at Vdd min */
uint8_t vddwcurrmax; /* 52:50 Max. write current at Vdd max */
uint8_t csizemult; /* 49:47 Device size multiplier */
union
{
struct /* MMC system specification version 3.1 */
{
uint8_t ergrpsize; /* 46:42 Erase group size (MMC 3.1) */
uint8_t ergrpmult; /* 41:37 Erase group multiplier (MMC 3.1) */
} mmc31;
struct /* MMC system specification version 2.2 */
{
uint8_t sectorsize; /* 46:42 Erase sector size (MMC 2.2) */
uint8_t ergrpsize; /* 41:37 Erase group size (MMC 2.2) */
} mmc22;
} er;
uint8_t mmcwpgrpsize; /* 36:32 Write protect group size (MMC) */
} mmc;
#endif
struct
{
uint16_t csize; /* 73:62 Device size */
uint8_t vddrcurrmin; /* 61:59 Max. read current at Vdd min */
uint8_t vddrcurrmax; /* 58:56 Max. read current at Vdd max */
uint8_t vddwcurrmin; /* 55:53 Max. write current at Vdd min */
uint8_t vddwcurrmax; /* 52:50 Max. write current at Vdd max */
uint8_t csizemult; /* 49:47 Device size multiplier */
uint8_t sderblen; /* 46:46 Erase single block enable (SD) */
uint8_t sdsectorsize; /* 45:39 Erase sector size (SD) */
uint8_t sdwpgrpsize; /* 38:32 Write protect group size (SD) */
} sdbyte;
struct
{
/* 73:70 (reserved) */
uint32_t csize; /* 69:48 Device size */
/* 47:47 (reserved) */
uint8_t sderblen; /* 46:46 Erase single block enable (SD) */
uint8_t sdsectorsize; /* 45:39 Erase sector size (SD) */
uint8_t sdwpgrpsize; /* 38:32 Write protect group size (SD) */
} sdblock;
} u;
uint8_t wpgrpen; /* 31:31 Write protect group enable */
uint8_t mmcdfltecc; /* 30:29 Manufacturer default ECC (MMC) */
uint8_t r2wfactor; /* 28:26 Write speed factor */
uint8_t writebllen; /* 25:22 Max. write data block length */
uint8_t writeblpartial; /* 21:21 Partial blocks for write allowed */
uint8_t fileformatgrp; /* 15:15 File format group */
uint8_t copy; /* 14:14 Copy flag (OTP) */
uint8_t permwriteprotect; /* 13:13 Permanent write protection */
uint8_t tmpwriteprotect; /* 12:12 Temporary write protection */
uint8_t fileformat; /* 10:11 File format */
uint8_t mmcecc; /* 9:8 ECC (MMC) */
uint8_t crc; /* 7:1 CRC */
/* 0:0 Not used */
};
struct mmcsd_scr_s
{
uint8_t scrversion; /* 63:60 Version of SCR structure */
uint8_t sdversion; /* 59:56 SD memory card physical layer version */
uint8_t erasestate; /* 55:55 Data state after erase (1 or 0) */
uint8_t security; /* 54:52 SD security support */
uint8_t buswidth; /* 51:48 DAT bus widthes supported */
/* 47:32 SD reserved space */
uint32_t mfgdata; /* 31:0 Reserved for manufacturing data */
};
/********************************************************************************************
* Public Data
********************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/********************************************************************************************
* Public Functions
********************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __DRIVERS_MMCSD_MMCSD_SDIO_H */
|
