1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
|
/************************************************************************************
* configs/sama5d3x-ek/src/sam_ethernet.c
*
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/irq.h>
#include "sam_pio.h"
#include "sam_ethernet.h"
#ifdef HAVE_NETWORK
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/************************************************************************************
* Private Data
************************************************************************************/
#ifdef CONFIG_SAMA5_PIOE_IRQ
#ifdef CONFIG_SAMA5_EMACA
static xcpt g_emac_handler;
#endif
#ifdef CONFIG_SAMA5_GMAC
static xcpt g_gmac_handler;
#endif
#endif
/************************************************************************************
* Private Functions
************************************************************************************/
/************************************************************************************
* Public Functions
************************************************************************************/
/************************************************************************************
* Name: sam_netinitialize
*
* Description:
* Configure board resources to support networking.
*
************************************************************************************/
void weak_function sam_netinitialize(void)
{
#ifdef CONFIG_SAMA4_EMACA
/* Ethernet 10/100 (EMAC A) Port
*
* The main board contains a MICREL PHY device (KSZ8051) operating at 10/100 Mbps.
* The board supports MII and RMII interface modes.
*
* The two independent PHY devices embedded on CM and MB boards are connected to
* independent RJ-45 connectors with built-in magnetic and status LEDs.
*
* At the De-Assertion of Reset:
* PHY ADD[2:0]:001
* CONFIG[2:0]:001,Mode:RMII
* Duplex Mode:Half Duplex
* Isolate Mode:Disable
* Speed Mode:100Mbps
* Nway Auto-Negotiation:Enable
*
* The KSZ8051 PHY interrtup is available on PE30 INT_ETH1
*/
sam_configpio(PIO_INT_ETH1);
#endif
#ifdef CONFIG_SAMA4_GMAC
/* Tri-Speed Ethernet PHY
*
* The SAMA5D3 series-CM board is equipped with a MICREL PHY devices (MICREL
* KSZ9021/31) operating at 10/100/1000 Mbps. The board supports RGMII interface
* mode. The Ethernet interface consists of 4 pairs of low voltage differential
* pair signals designated from GRX� and GTx� plus control signals for link
* activity indicators. These signals can be used to connect to a 10/100/1000
* BaseT RJ45 connector integrated on the main board.
*
* The KSZ9021/31 interrupt is available on PB35 INT_GETH0
*/
sam_configpio(PIO_INT_ETH0);
#endif
}
/************************************************************************************
* Name: sam_phyirq
*
* Description:
* This function may be called to register an interrupt handler that will be
* called when an interrupt is received from a PHY.
*
************************************************************************************/
#ifdef CONFIG_SAMA5_PIOE_IRQ
xcpt_t sam_phyirq(int intf, xcpt_t irqhandler)
{
irqstate_t flags;
xcpt_t *handler;
xcpt_t oldhandler;
pio_pinset_t pinset;
int irq;
#ifdef CONFIG_SAMA5_EMACA
if (intf == EMAC_INTF)
{
handler = &g_emac_handler;
pinset = PIO_INT_ETH1;
irq = IRQ_INT_ETH1;
}
else
#endif
#ifdef CONFIG_SAMA5_GMAC
if (intf == GMAC_INTF)
{
handler = &g_gmac_handler;
pinset = PIO_INT_ETH0;
irq = IRQ_INT_ETH0;
}
else
#endif
{
ndbg("Unsupported interface: %d\n", intf);
return NULL;
}
/* Disable interrupts until we are done. This guarantees that the
* following operations are atomic.
*/
flags = irqsave();
/* Get the old button interrupt handler and save the new one */
oldhandler = *handler;
*handler = irqhandler;
/* Configure the interrupt */
sam_pioirq(pinset);
(void)irq_attach(irq, irqhandler);
sam_pioirqenable(irq);
/* Return the old button handler (so that it can be restored) */
irqrestore(flags);
return oldhandler;
}
#endif /* CONFIG_SAMA5_PIOE_IRQ */
#endif /* HAVE_NETWORK */
|
