1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
|
mm/README.txt
=============
This directory contains the NuttX memory management logic. This include:
1) Standard Memory Management Functions:
Standard Functions:
The standard memory management functions as prototyped in stdlib.h as
specified in the Base definitions volume of IEEE Std 1003.1-2001. This
include the files:
o Standard Interfaces: mm_malloc.c, mm_calloc.c, mm_realloc.c,
mm_memalign.c, mm_free.c
o Less-Standard Interfaces: mm_zalloc.c, mm_mallinfo.c
o Internal Implementation: mm_initialize.c mm_sem.c mm_addfreechunk.c
mm_size2ndx.c mm_shrinkchunk.c, mm_internal.h
o Build and Configuration files: Kconfig, Makefile
Memory Models:
o Small Memory Model. If the MCU supports only 16-bit data addressing
then the small memory model is automatically used. The maximum size
of the heap is then 64K. The small memory model can also be forced
MCUs with wider addressing by defining CONFIG_SMALL_MEMORY in the
NuttX configuration file.
o Large Memory Model. Otherwise, the allocator uses a model that
supports a heap of up to 4G.
This implementation uses a variable length allocator with the following
properties:
o Overhead: Either 8- or 4-bytes per allocation for large and small
models, respectively.
o Alignment: All allocations are aligned to 8- or 4-bytes for large
and small models, respectively.
Multiple Heaps:
This allocator can be used to manage multiple heaps (albeit with some
non-standard interfaces). A heap is represented by struct mm_heap_s
as defined in the file include/nuttx/mm/mm.h. To create another heap
instance, you would allocate a heap structure, most likely statically
in memory:
include <nuttx/mm/mm.h>
static struct mm_heap_s g_myheap;
Then initialize the heap using:
mm_initialize(&g_myheap, myheap_start, myheap_size);
Where mm_initialize() and all related interfaces are prototyped in the
header file include/nuttx/mm/mm.h.
After the new heap instance has been initialized, it can then be used
with these almost familiar interfaces: mm_malloc(), mm_realloc(), mm_free(),
etc. These are 'almost familiar' because they are analogous of the
standard malloc(), realloc(), free(), etc. except that they expect a
reference to the initialized heap structure as the first parameter.
In fact, the standard malloc(), realloc(), free() use this same mechanism,
but with a global heap structure called g_mmheap.
User/Kernel Heaps
This multiple heap capability is exploited in some of the more complex NuttX
build configurations to provide separate kernel-mode and user-mode heaps.
Sub-Directories:
mm/mm_heap - Holds the common base logic for all heap allocators
mm/umm_heap - Holds the user-mode memory allocation interfaces
mm/kmm_heap - Holds the kernel-mode memory allocation interfaces
2) Granule Allocator.
A non-standard granule allocator is also available in this directory The
granule allocator allocates memory in units of a fixed sized block ("granule").
Allocations may be aligned to a user-provided address boundary.
The granule allocator interfaces are defined in nuttx/include/nuttx/mm/gran.h.
The granule allocator consists of these files in this directory:
mm_gran.h, mm_granalloc.c, mm_grancritical.c, mm_granfree.c
mm_graninit.c
The granule allocator is not used anywhere within the base NuttX code
as of this writing. The intent of the granule allocator is to provide
a tool to support platform-specific management of aligned DMA memory.
NOTE: Because each granule may be aligned and each allocation is in
units of the granule size, selection of the granule size is important:
Larger granules will give better performance and less overhead but more
losses of memory due to quantization waste. Additional memory waste
can occur from alignment; Of course, heap alignment should no be
used unless (a) you are using the granule allocator to manage DMA memory
and (b) your hardware has specific memory alignment requirements.
The current implementation also restricts the maximum allocation size
to 32 granules. That restriction could be eliminated with some
additional coding effort, but currently requires larger granule
sizes for larger allocations.
General Usage Example.
This is an example using the GCC section attribute to position a DMA
heap in memory (logic in the linker script would assign the section
.dmaheap to the DMA memory.
FAR uint32_t g_dmaheap[DMAHEAP_SIZE] __attribute__((section(.dmaheap)));
The heap is created by calling gran_initialize. Here the granule size
is set to 64 bytes and the alignment to 16 bytes:
GRAN_HANDLE handle = gran_initialize(g_dmaheap, DMAHEAP_SIZE, 6, 4);
Then the GRAN_HANDLE can be used to allocate memory (There is no
GRAN_HANDLE if CONFIG_GRAN_SINGLE=y):
FAR uint8_t *dma_memory = (FAR uint8_t *)gran_alloc(handle, 47);
The actual memory allocates will be 64 byte (wasting 17 bytes) and
will be aligned at least to (1 << log2align).
Sub-Directories:
mm/mm_gran - Holds the granule allocation logic
3) Page Allocator
The page allocator is an application of the granule allocator. It is a
special purpose memory allocator intended to allocate physical memory
pages for use with systems that have a memory management unit (MMU).
Sub-Directories:
mm/mm_gran - The page allocator cohabits the same directory as the
granule allocator.
4) Shared Memory Management
When NuttX is build in kernel mode with a separate, privileged, kernel-
mode address space and multiple, unprivileged, user-mode address spaces,
then shared memory regions must also be managed. Shared memory regions
are user-accessible memory regions that can be attached into the user
process address space for sharing between user process.
Sub-Directories:
mm/shm - The shared memory logic
The shared memory management logic has its own README file that can be
found at nuttx/mm/shm/README.txt.
|
