/****************************************************************************
*
* Copyright (c) 2015 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name PX4 nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/**
* @file px4cannode_led.c
*
* PX4FMU SPI backend.
*/
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <stdbool.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/spi/spi.h>
#include <arch/board/board.h>
#include <nuttx/board.h>
#include "chip.h"
#include "stm32.h"
#include "board_config.h"
#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2) || defined(CONFIG_STM32_SPI3)
/************************************************************************************
* Definitions
************************************************************************************/
/* Enables debug output from this file (needs CONFIG_DEBUG too) */
#undef SPI_DEBUG /* Define to enable debug */
#undef SPI_VERBOSE /* Define to enable verbose debug */
#ifdef SPI_DEBUG
# define spidbg lldbg
# ifdef SPI_VERBOSE
# define spivdbg lldbg
# else
# define spivdbg(x...)
# endif
#else
# undef SPI_VERBOSE
# define spidbg(x...)
# define spivdbg(x...)
#endif
/************************************************************************************
* Private Functions
************************************************************************************/
/************************************************************************************
* Public Functions
************************************************************************************/
/************************************************************************************
* Name: stm32_spiinitialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the board.
*
************************************************************************************/
void weak_function board_spiinitialize(void)
{
/* Setup CS */
#ifdef CONFIG_STM32_SPI1
stm32_configgpio(USER_CSn);
#endif
#ifdef CONFIG_STM32_SPI2
stm32_configgpio(MMCSD_CSn);
#endif
}
/****************************************************************************
* Name: stm32_spi1/2/3select and stm32_spi1/2/3status
*
* Description:
* The external functions, stm32_spi1/2/3select and stm32_spi1/2/3status
* must be provided by board-specific logic. They are implementations of
* the select and status methods of the SPI interface defined by struct
* spi_ops_s (see include/nuttx/spi/spi.h). All other methods (including
* up_spiinitialize()) are provided by common STM32 logic. To use this
* common SPI logic on your board:
*
* 1. Provide logic in stm32_boardinitialize() to configure SPI chip
* select pins.
* 2. Provide stm32_spi1/2/3select() and stm32_spi1/2/3status() functions
* in your board-specific logic. These functions will perform chip
* selection and status operations using GPIOs in the way your board
* is configured.
* 3. Add a calls to up_spiinitialize() in your low level application
* initialization logic
* 4. The handle returned by up_spiinitialize() may then be used to bind
* the SPI driver to higher level logic (e.g., calling
* mmcsd_spislotinitialize(), for example, will bind the SPI driver to
* the SPI MMC/SD driver).
*
****************************************************************************/
#ifdef CONFIG_STM32_SPI1
void stm32_spi1select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
{
spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
if (devid == SPIDEV_USER)
{
stm32_gpiowrite(USER_CSn, !selected);
}
}
uint8_t stm32_spi1status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
{
return 0;
}
#endif
#ifdef CONFIG_STM32_SPI2
void stm32_spi2select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
{
spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
#if defined(CONFIG_MMCSD)
if (devid == SPIDEV_MMCSD)
{
stm32_gpiowrite(MMCSD_CSn, !selected);
}
#endif
}
uint8_t stm32_spi2status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
{
/* No switch on SD card socket so assume it is here */
return SPI_STATUS_PRESENT;
}
#endif
#ifdef CONFIG_STM32_SPI3
void stm32_spi3select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
{
spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
}
uint8_t stm32_spi3status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
{
return 0;
}
#endif
/****************************************************************************
* Name: stm32_spi1cmddata
*
* Description:
* Set or clear the SH1101A A0 or SD1306 D/C n bit to select data (true)
* or command (false). This function must be provided by platform-specific
* logic. This is an implementation of the cmddata method of the SPI
* interface defined by struct spi_ops_s (see include/nuttx/spi/spi.h).
*
* Input Parameters:
*
* spi - SPI device that controls the bus the device that requires the CMD/
* DATA selection.
* devid - If there are multiple devices on the bus, this selects which one
* to select cmd or data. NOTE: This design restricts, for example,
* one one SPI display per SPI bus.
* cmd - true: select command; false: select data
*
* Returned Value:
* None
*
****************************************************************************/
#ifdef CONFIG_SPI_CMDDATA
#ifdef CONFIG_STM32_SPI1
int stm32_spi1cmddata(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool cmd)
{
return OK;
}
#endif
#ifdef CONFIG_STM32_SPI2
int stm32_spi2cmddata(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool cmd)
{
return OK;
}
#endif
#ifdef CONFIG_STM32_SPI3
int stm32_spi3cmddata(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool cmd)
{
return -ENODEV;
}
#endif
#endif /* CONFIG_SPI_CMDDATA */
#endif /* CONFIG_STM32_SPI1 || CONFIG_STM32_SPI2 */
