diff options
Diffstat (limited to 'nuttx/configs/olimex-lpc1766stk')
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/ftpc/defconfig | 525 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/hidkbd/defconfig | 461 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/nettest/defconfig | 435 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/nsh/defconfig | 486 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/nx/defconfig | 582 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/ostest/defconfig | 466 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/slip-httpd/defconfig | 499 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/thttpd/defconfig | 496 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/usbserial/defconfig | 465 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig | 465 | ||||
-rwxr-xr-x | nuttx/configs/olimex-lpc1766stk/wlan/defconfig | 460 |
11 files changed, 11 insertions, 5329 deletions
diff --git a/nuttx/configs/olimex-lpc1766stk/ftpc/defconfig b/nuttx/configs/olimex-lpc1766stk/ftpc/defconfig index 9fc6d6f5d..a7f4fb6d5 100755 --- a/nuttx/configs/olimex-lpc1766stk/ftpc/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/ftpc/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=y CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,24 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -219,19 +154,6 @@ CONFIG_NET_REGDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -241,94 +163,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# CONFIG_SCHED_WAITPID - Enable the waitpid() function -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -363,16 +197,6 @@ CONFIG_SCHED_WAITPID=y # # Settings for NXFLAT # -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals -# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and -# CONFIG_DEBUG_BINFMT have to be defined or -# CONFIG_NXFLAT_DUMPBUFFER does nothing. -# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table -# is ordered by symbol name -# CONFIG_NXFLAT=y CONFIG_NXFLAT_DUMPBUFFER=n CONFIG_SYMTAB_ORDEREDBYNAME=y @@ -404,9 +228,6 @@ CONFIG_DISABLE_POLL=n # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -429,39 +250,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed or fdopend'ed. This needs to be pretty -# large for ftpc because it uses two streams per socket. -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -479,46 +267,6 @@ CONFIG_PREALLOC_TIMERS=8 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=y CONFIG_FAT_LCNAMES=y CONFIG_FAT_LFN=y @@ -529,13 +277,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -543,53 +284,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=y CONFIG_NET_IPv6=n @@ -615,8 +321,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -624,22 +328,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -652,20 +340,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # USB Host Configuration # -# CONFIG_USBHOST -# Enables USB host support -# CONFIG_USBHOST_NPREALLOC -# Number of pre-allocated class instances -# CONFIG_USBHOST_BULK_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling bulk endpoint support -# CONFIG_USBHOST_INT_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling interrupt endpoint support -# CONFIG_USBHOST_ISOC_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling isochronous endpoint support -# CONFIG_USBHOST=n CONFIG_USBHOST_NPREALLOC=0 CONFIG_USBHOST_BULK_DISABLE=n @@ -675,19 +349,6 @@ CONFIG_USBHOST_ISOC_DISABLE=y # # LPC17xx USB Device Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -698,18 +359,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # LPC17xx USB Host Configuration # # OHCI RAM layout: -# CONFIG_USBHOST_OHCIRAM_SIZE -# Total size of OHCI RAM (in AHB SRAM Bank 1) -# CONFIG_USBHOST_NEDS -# Number of endpoint descriptors -# CONFIG_USBHOST_NTDS -# Number of transfer descriptors -# CONFIG_USBHOST_TDBUFFERS -# Number of transfer descriptor buffers -# CONFIG_USBHOST_TDBUFSIZE -# Size of one transfer descriptor buffer -# CONFIG_USBHOST_IOBUFSIZE -# Size of one end-user I/O buffer # CONFIG_USBHOST_OHCIRAM_SIZE=1536 CONFIG_USBHOST_NEDS=2 @@ -721,26 +370,6 @@ CONFIG_USBHOST_IOBUFSIZE=512 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -757,26 +386,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -795,61 +404,6 @@ CONFIG_USBMSC_REMOVABLE=y # # THTTPD settings # -# CONFIG_THTTPD_PORT - THTTPD Server port number -# CONFIG_THTTPD_IPADDR - Server IP address (no host name) -# CONFIG_THTTPD_SERVER_ADDRESS - SERVER_ADDRESS: response -# CONFIG_THTTPD_SERVER_SOFTWARE - SERVER_SOFTWARE: response -# CONFIG_THTTPD_PATH - Server working directory -# CONFIG_THTTPD_CGI_PATH - Path to CGI executables -# CONFIG_THTTPD_CGI_PATTERN - Only CGI programs matching this -# pattern will be executed. In fact, if this value is not defined -# then no CGI logic will be built. -# CONFIG_THTTPD_CGI_PRIORITY - Provides the priority of CGI child tasks -# CONFIG_THTTPD_CGI_STACKSIZE - Provides the initial stack size of -# CGI child task (will be overridden by the stack size in the NXFLAT -# header) -# CONFIG_THTTPD_CGI_BYTECOUNT - Byte output limit for CGI tasks. -# CONFIG_THTTPD_CGI_TIMELIMIT - How many seconds to allow CGI programs -# to run before killing them. -# CONFIG_THTTPD_CHARSET- The default character set name to use with -# text MIME types. -# CONFIG_THTTPD_IOBUFFERSIZE - -# CONFIG_THTTPD_INDEX_NAMES - A list of index filenames to check. The -# files are searched for in this order. -# CONFIG_AUTH_FILE - The file to use for authentication. If this is -# defined then thttpd checks for this file in the local directory -# before every fetch. If the file exists then authentication is done, -# otherwise the fetch proceeds as usual. If you leave this undefined -# then thttpd will not implement authentication at all and will not -# check for auth files, which saves a bit of CPU time. A typical -# value is ".htpasswd" -# CONFIG_THTTPD_LISTEN_BACKLOG - The listen() backlog queue length. -# CONFIG_THTTPD_LINGER_MSEC - How many milliseconds to leave a connection -# open while doing a lingering close. -# CONFIG_THTTPD_OCCASIONAL_MSEC - How often to run the occasional -# cleanup job. -# CONFIG_THTTPD_IDLE_READ_LIMIT_SEC - How many seconds to allow for -# reading the initial request on a new connection. -# CONFIG_THTTPD_IDLE_SEND_LIMIT_SEC - How many seconds before an -# idle connection gets closed. -# CONFIG_THTTPD_TILDE_MAP1 and CONFIG_THTTPD_TILDE_MAP2 - Tilde mapping. -# Many URLs use ~username to indicate a user's home directory. thttpd -# provides two options for mapping this construct to an actual filename. -# 1) Map ~username to <prefix>/username. This is the recommended choice. -# Each user gets a subdirectory in the main web tree, and the tilde -# construct points there. The prefix could be something like "users", -# or it could be empty. -# 2) Map ~username to <user's homedir>/<postfix>. The postfix would be -# the name of a subdirectory off of the user's actual home dir, -# something like "public_html". -# You can also leave both options undefined, and thttpd will not do -# anything special about tildes. Enabling both options is an error. -# Typical values, if they're defined, are "users" for -# CONFIG_THTTPD_TILDE_MAP1 and "public_html"forCONFIG_THTTPD_TILDE_MAP2. -# CONFIG_THTTPD_GENERATE_INDICES -# CONFIG_THTTPD_URLPATTERN - If defined, then it will be used to match -# and verify referrers. -# CONFIG_THTTPD_PORT=80 CONFIG_THTTPD_IPADDR=0x0a000002 CONFIG_THTTPD_SERVER_ADDRESS="http://www.nuttx.org" @@ -892,18 +446,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -923,12 +465,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -945,36 +481,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_BUILTIN_APPS=y CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n @@ -1016,15 +522,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -1039,26 +536,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/hidkbd/defconfig b/nuttx/configs/olimex-lpc1766stk/hidkbd/defconfig index f6e69d391..85333830d 100755 --- a/nuttx/configs/olimex-lpc1766stk/hidkbd/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/hidkbd/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=y @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,24 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -219,19 +154,6 @@ CONFIG_NET_REGDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -241,96 +163,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -388,9 +220,6 @@ CONFIG_DISABLE_POLL=n # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -413,38 +242,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -462,46 +259,6 @@ CONFIG_PREALLOC_TIMERS=4 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -512,13 +269,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -526,53 +276,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=n CONFIG_NET_IPv6=n @@ -598,8 +313,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -607,22 +320,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -635,20 +332,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # USB Host Configuration # -# CONFIG_USBHOST -# Enables USB host support -# CONFIG_USBHOST_NPREALLOC -# Number of pre-allocated class instances -# CONFIG_USBHOST_BULK_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling bulk endpoint support -# CONFIG_USBHOST_INT_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling interrupt endpoint support -# CONFIG_USBHOST_ISOC_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling isochronous endpoint support -# CONFIG_USBHOST=y CONFIG_USBHOST_NPREALLOC=0 CONFIG_USBHOST_BULK_DISABLE=y @@ -658,19 +341,6 @@ CONFIG_USBHOST_ISOC_DISABLE=y # # LPC17xx USB Device Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -681,18 +351,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # LPC17xx USB Host Configuration # # OHCI RAM layout: -# CONFIG_USBHOST_OHCIRAM_SIZE -# Total size of OHCI RAM (in AHB SRAM Bank 1) -# CONFIG_USBHOST_NEDS -# Number of endpoint descriptors -# CONFIG_USBHOST_NTDS -# Number of transfer descriptors -# CONFIG_USBHOST_TDBUFFERS -# Number of transfer descriptor buffers -# CONFIG_USBHOST_TDBUFSIZE -# Size of one transfer descriptor buffer -# CONFIG_USBHOST_IOBUFSIZE -# Size of one end-user I/O buffer # CONFIG_USBHOST_OHCIRAM_SIZE=1536 CONFIG_USBHOST_NEDS=2 @@ -704,26 +362,6 @@ CONFIG_USBHOST_IOBUFSIZE=512 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -740,26 +378,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -785,18 +403,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -816,12 +422,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -838,36 +438,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -903,15 +473,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -926,26 +487,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/nettest/defconfig b/nuttx/configs/olimex-lpc1766stk/nettest/defconfig index d072367b6..d46de05f4 100755 --- a/nuttx/configs/olimex-lpc1766stk/nettest/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/nettest/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=y CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,24 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -219,19 +154,6 @@ CONFIG_NET_REGDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -241,96 +163,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -388,9 +220,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -413,38 +242,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=8 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=0 @@ -462,46 +259,6 @@ CONFIG_PREALLOC_TIMERS=8 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -512,13 +269,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -526,53 +276,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=y CONFIG_NET_IPv6=n @@ -598,8 +313,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -607,22 +320,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -635,19 +332,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -657,26 +341,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -693,26 +357,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -738,18 +382,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -769,12 +401,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -791,36 +417,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -856,15 +452,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -879,26 +466,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/nsh/defconfig b/nuttx/configs/olimex-lpc1766stk/nsh/defconfig index 0ad922ed3..fac5a7039 100755 --- a/nuttx/configs/olimex-lpc1766stk/nsh/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/nsh/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=y CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,24 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -219,19 +154,6 @@ CONFIG_NET_REGDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -241,95 +163,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# CONFIG_SCHED_WAITPID - Enable the waitpid() API -# CONFIG_SCHED_ATEXIT - Enabled the atexit() API -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -367,16 +200,6 @@ CONFIG_SCHED_ATEXIT=n # # Settings for NXFLAT # -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals -# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and -# CONFIG_DEBUG_BINFMT have to be defined or -# CONFIG_NXFLAT_DUMPBUFFER does nothing. -# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table -# is ordered by symbol name -# CONFIG_NXFLAT=y CONFIG_NXFLAT_DUMPBUFFER=n CONFIG_SYMTAB_ORDEREDBYNAME=y @@ -408,9 +231,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -433,38 +253,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -482,46 +270,6 @@ CONFIG_PREALLOC_TIMERS=4 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=y CONFIG_FAT_LCNAMES=y CONFIG_FAT_LFN=y @@ -532,13 +280,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -546,53 +287,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=y CONFIG_NET_IPv6=n @@ -618,8 +324,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -627,19 +331,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # CAN device driver settings # -# CONFIG_CAN - Enables CAN support (one or both of CONFIG_LPC17_CAN1 or -# CONFIG_LPC17_CAN2 must also be defined) -# CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default -# Standard 11-bit IDs. -# CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages. -# Default: 8 -# CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests. -# Default: 4 -# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback -# mode for testing. The STM32 CAN driver does support loopback mode. -# CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_LPC17_CAN1 is defined. -# CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_LPC17_CAN2 is defined. -# CONFIG_CAN=n CONFIG_CAN_EXTID=n #CONFIG_CAN_FIFOSIZE @@ -652,22 +343,6 @@ CONFIG_CAN2_BAUD=700000 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -680,20 +355,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # USB Host Configuration # -# CONFIG_USBHOST -# Enables USB host support -# CONFIG_USBHOST_NPREALLOC -# Number of pre-allocated class instances -# CONFIG_USBHOST_BULK_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling bulk endpoint support -# CONFIG_USBHOST_INT_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling interrupt endpoint support -# CONFIG_USBHOST_ISOC_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling isochronous endpoint support -# CONFIG_USBHOST=n CONFIG_USBHOST_NPREALLOC=0 CONFIG_USBHOST_BULK_DISABLE=n @@ -703,19 +364,6 @@ CONFIG_USBHOST_ISOC_DISABLE=y # # LPC17xx USB Device Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -726,18 +374,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # LPC17xx USB Host Configuration # # OHCI RAM layout: -# CONFIG_USBHOST_OHCIRAM_SIZE -# Total size of OHCI RAM (in AHB SRAM Bank 1) -# CONFIG_USBHOST_NEDS -# Number of endpoint descriptors -# CONFIG_USBHOST_NTDS -# Number of transfer descriptors -# CONFIG_USBHOST_TDBUFFERS -# Number of transfer descriptor buffers -# CONFIG_USBHOST_TDBUFSIZE -# Size of one transfer descriptor buffer -# CONFIG_USBHOST_IOBUFSIZE -# Size of one end-user I/O buffer # CONFIG_USBHOST_OHCIRAM_SIZE=1536 CONFIG_USBHOST_NEDS=2 @@ -749,26 +385,6 @@ CONFIG_USBHOST_IOBUFSIZE=512 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -785,26 +401,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -830,18 +426,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -861,12 +445,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -883,39 +461,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_BUILTIN_APPS - Support external registered, -# "named" applications that can be executed from the NSH -# command line (see apps/README.txt for more information). -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_BUILTIN_APPS=y CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n @@ -952,15 +497,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -975,26 +511,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/nx/defconfig b/nuttx/configs/olimex-lpc1766stk/nx/defconfig index d50e3b160..be5d1657b 100755 --- a/nuttx/configs/olimex-lpc1766stk/nx/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/nx/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,22 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -213,19 +150,6 @@ CONFIG_PHY_FDUPLEX=y # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -240,96 +164,6 @@ CONFIG_SPI_CMDDATA=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n @@ -392,9 +226,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -417,38 +248,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -474,46 +273,6 @@ CONFIG_FB_HWCURSORIMAGE=n # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -524,13 +283,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -538,53 +290,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=n CONFIG_NET_IPv6=n @@ -608,8 +325,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -617,22 +332,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -645,19 +344,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -667,26 +353,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -703,26 +369,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -741,64 +387,6 @@ CONFIG_USBMSC_REMOVABLE=y # # Graphics related configuration settings # -# CONFIG_NX -# Enables overall support for graphics library and NX -# CONFIG_NX_MULTIUSER -# Configures NX in multi-user mode -# CONFIG_NX_NPLANES -# Some YUV color formats requires support for multiple planes, -# one for each color component. Unless you have such special -# hardware, this value should be undefined or set to 1 -# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP, -# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP, -# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and -# CONFIG_NX_DISABLE_32BPP -# NX supports a variety of pixel depths. You can save some -# memory by disabling support for unused color depths. -# CONFIG_NX_PACKEDMSFIRST -# If a pixel depth of less than 8-bits is used, then NX needs -# to know if the pixels pack from the MS to LS or from LS to MS -# CONFIG_NX_LCDDRIVER -# By default, NX builds to use a framebuffer driver (see -# include/nuttx/fb.h). If this option is defined, NX will -# build to use an LCD driver (see include/nuttx/lcd/lcd.h). -# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device. -# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device. -# CONFIG_NX_MOUSE -# Build in support for mouse input -# CONFIG_NX_KBD -# Build in support of keypad/keyboard input -# CONFIG_NXTK_BORDERWIDTH -# Specifies with with of the border (in pixels) used with -# framed windows. The default is 4. -# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2 -# Specify the colors of the border used with framed windows. -# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so -# is normally darker. The default is medium and dark grey, -# respectively -# CONFIG_NXTK_AUTORAISE -# If set, a window will be raised to the top if the mouse position -# is over a visible portion of the window. Default: A mouse -# button must be clicked over a visible portion of the window. -# CONFIG_NXFONTS_CHARBITS -# The number of bits in the character set. Current options are -# only 7 and 8. The default is 7. -# CONFIG_NXFONT_SANS23X27 -# At present, there is only one font. But if there were were more, -# then this option would select the sans serif font. -# -# NX Multi-user only options: -# -# CONFIG_NX_BLOCKING -# Open the client message queues in blocking mode. In this case, -# nx_eventhandler() will not return until a message is received and processed. -# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS -# Specifies the maximum number of messages that can fit in -# the message queues. No additional resources are allocated, but -# this can be set to prevent flooding of the client or server with -# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many -# messages are pre-allocated). -# CONFIG_NX=y CONFIG_NX_MULTIUSER=n CONFIG_NX_NPLANES=1 @@ -828,20 +416,6 @@ CONFIG_NX_MXCLIENTMSGS=16 # # RiT P14201 OLED Driver Configuration # -# CONFIG_LCD_P14201 - Enable P14201 support -# CONFIG_P14201_SPIMODE - Controls the SPI mode (should be mode 2) -# CONFIG_P14201_FREQUENCY - Define to use a different bus frequency -# CONFIG_P14201_NINTERFACES - Specifies the number of physical P14201 devices that -# will be supported. -# CONFIG_P14201_FRAMEBUFFER - If defined, accesses will be performed using an in-memory -# copy of the OLEDs GDDRAM. This cost of this buffer is 128 * 96 / 2 = 6Kb. If this -# is defined, then the driver will be fully functional. If not, then it will have the -# following limitations: -# - Reading graphics memory cannot be supported, and -# - All pixel writes must be aligned to byte boundaries. -# -# The latter limitation effectively reduces the 128x96 disply to 64x96. -# CONFIG_LCD_P14201=n CONFIG_P14201_SPIMODE=2 CONFIG_P14201_FREQUENCY=3500000 @@ -853,26 +427,6 @@ CONFIG_P14201_FRAMEBUFFER=y # # Nokia 6100 Configuration Settings: # -# CONFIG_NOKIA6100_SPIMODE - Controls the SPI mode -# CONFIG_NOKIA6100_FREQUENCY - Define to use a different bus frequency -# CONFIG_NOKIA6100_NINTERFACES - Specifies the number of physical Nokia -# 6100 devices that will be supported. -# CONFIG_NOKIA6100_BPP - Device supports 8, 12, and 16 bits per pixel. -# CONFIG_NOKIA6100_S1D15G10 - Selects the Epson S1D15G10 display controller -# CONFIG_NOKIA6100_PCF8833 - Selects the Phillips PCF8833 display controller -# CONFIG_NOKIA6100_BLINIT - Initial backlight setting -# -# Required LCD driver settings: -# CONFIG_LCD_NOKIA6100 - Enable Nokia 6100 support -# Required LCD driver settings: -# CONFIG_LCD_NOKIA6100 - Enable Nokia 6100 support -# CONFIG_LCD_MAXCONTRAST - must be 63 with the Epson controller and 127 with -# the Phillips controller. -# CONFIG_LCD_MAXPOWER - Maximum value of backlight setting. The backlight -# control is managed outside of the 6100 driver so this value has no -# meaning to the driver. Board-specific logic may place restrictions on -# this value. -# CONFIG_LCD_NOKIA6100=y #CONFIG_NOKIA6100_SPIMODE #CONFIG_NOKIA6100_FREQUENCY @@ -894,18 +448,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -925,12 +467,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -947,36 +483,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -1012,15 +518,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -1035,38 +532,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Settings for examples/usbstorage # -# CONFIG_EXAMPLES_USBMSC_NLUNS -# Defines the number of logical units (LUNs) exported by the USB storage -# driver. Each LUN corresponds to one exported block driver (or partition -# of a block driver). May be 1, 2, or 3. Default is 1. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR1 -# The minor device number of the block driver for the first LUN. For -# example, N in /dev/mmcsdN. Used for registering the block driver. Default -# is zero. -# CONFIG_EXAMPLES_USBMSC_DEVPATH1 -# The full path to the registered block driver. Default is "/dev/mmcsd0" -# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 2 or 3. No defaults. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 3. No defaults. -# -# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then -# the example code will also manage the USB trace output. The amount of trace output -# can be controlled using: -# -# CONFIG_EXAMPLES_USBMSC_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_USBMSC_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_USBMSC_NLUNS=1 CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0 CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0" @@ -1079,31 +544,6 @@ CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n # # Settings for examples/nx # -# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame- -# buffer driver for use in the test. Default: 0 -# CONFIG_EXAMPLES_NX_DEVNO - The LCD device to select from the LCD -# driver for use in the test: Default: 0 -# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background. Default depends on -# CONFIG_EXAMPLES_NX_BPP. -# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on -# CONFIG_EXAMPLES_NX_BPP. -# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on -# CONFIG_EXAMPLES_NX_BPP. -# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on -# CONFIG_EXAMPLES_NX_BPP. -# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on -# CONFIG_EXAMPLES_NX_BPP. -# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use. Valid options -# include 2, 4, 8, 16, 24, and 32. Default is 32. -# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows; Default is to -# use pretty, framed NXTK windows with toolbars. -# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating -# the NX server. Default 2048 -# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority. Default: 80 -# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority. Default: 120 -# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with -# nx_eventnotify(). Default: 4 -# CONFIG_EXAMPLES_NX_VPLANE=0 CONFIG_EXAMPLES_NX_DEVNO=0 CONFIG_EXAMPLES_NX_BGCOLOR=0x02 @@ -1122,26 +562,6 @@ CONFIG_EXAMPLES_NX_EXTERNINIT=y # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/ostest/defconfig b/nuttx/configs/olimex-lpc1766stk/ostest/defconfig index 92aba7837..bc28760fc 100755 --- a/nuttx/configs/olimex-lpc1766stk/ostest/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/ostest/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,22 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -213,19 +150,6 @@ CONFIG_PHY_FDUPLEX=y # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -235,96 +159,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -381,9 +215,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -406,38 +237,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -455,46 +254,6 @@ CONFIG_PREALLOC_TIMERS=4 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -505,13 +264,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -519,53 +271,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=n CONFIG_NET_IPv6=n @@ -589,8 +306,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -598,22 +313,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -626,19 +325,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -648,26 +334,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -684,26 +350,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -730,19 +376,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest # -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) -# CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n CONFIG_EXAMPLE_NETTEST_NOMAC=y @@ -761,12 +394,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -783,36 +410,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -848,15 +445,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -871,38 +459,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Settings for examples/usbstorage # -# CONFIG_EXAMPLES_USBMSC_NLUNS -# Defines the number of logical units (LUNs) exported by the USB storage -# driver. Each LUN corresponds to one exported block driver (or partition -# of a block driver). May be 1, 2, or 3. Default is 1. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR1 -# The minor device number of the block driver for the first LUN. For -# example, N in /dev/mmcsdN. Used for registering the block driver. Default -# is zero. -# CONFIG_EXAMPLES_USBMSC_DEVPATH1 -# The full path to the registered block driver. Default is "/dev/mmcsd0" -# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 2 or 3. No defaults. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 3. No defaults. -# -# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then -# the example code will also manage the USB trace output. The amount of trace output -# can be controlled using: -# -# CONFIG_EXAMPLES_USBMSC_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_USBMSC_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_USBMSC_NLUNS=1 CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0 CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0" @@ -915,26 +471,6 @@ CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/slip-httpd/defconfig b/nuttx/configs/olimex-lpc1766stk/slip-httpd/defconfig index 79d3c7311..f72bfd936 100755 --- a/nuttx/configs/olimex-lpc1766stk/slip-httpd/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/slip-httpd/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -191,24 +144,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -218,19 +153,6 @@ CONFIG_NET_REGDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -240,93 +162,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -358,15 +193,6 @@ CONFIG_SIG_SIGWORK=4 # # Settings for nxflat -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals -# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and -# CONFIG_DEBUG_BINFMT have to be defined or -# CONFIG_NXFLAT_DUMPBUFFER does nothing. -# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table -# is ordered by symbol name # CONFIG_NXFLAT=y CONFIG_NXFLAT_DUMPBUFFER=n @@ -399,9 +225,6 @@ CONFIG_DISABLE_POLL=n # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -424,38 +247,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=0 @@ -473,46 +264,6 @@ CONFIG_PREALLOC_TIMERS=8 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -523,13 +274,6 @@ CONFIG_FS_ROMFS=y # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -537,56 +281,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_SLIP - Use the SLIP data link layer (L2) -# CONFIG_NET_NOINTS - uIP not called from interrupt level. -# CONFIG_NET_MULTIBUFFER - Use multiple input/output buffers (probably no) -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=y CONFIG_NET_SLIP=y @@ -615,8 +321,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -624,22 +328,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -652,19 +340,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -674,26 +349,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -710,26 +365,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -748,61 +383,6 @@ CONFIG_USBMSC_REMOVABLE=y # # THTTPD settings # -# CONFIG_THTTPD_PORT - THTTPD Server port number -# CONFIG_THTTPD_IPADDR - Server IP address (no host name) -# CONFIG_THTTPD_SERVER_ADDRESS - SERVER_ADDRESS: response -# CONFIG_THTTPD_SERVER_SOFTWARE - SERVER_SOFTWARE: response -# CONFIG_THTTPD_PATH - Server working directory -# CONFIG_THTTPD_CGI_PATH - Path to CGI executables -# CONFIG_THTTPD_CGI_PATTERN - Only CGI programs matching this -# pattern will be executed. In fact, if this value is not defined -# then no CGI logic will be built. -# CONFIG_THTTPD_CGI_PRIORITY - Provides the priority of CGI child tasks -# CONFIG_THTTPD_CGI_STACKSIZE - Provides the initial stack size of -# CGI child task (will be overridden by the stack size in the NXFLAT -# header) -# CONFIG_THTTPD_CGI_BYTECOUNT - Byte output limit for CGI tasks. -# CONFIG_THTTPD_CGI_TIMELIMIT - How many seconds to allow CGI programs -# to run before killing them. -# CONFIG_THTTPD_CHARSET- The default character set name to use with -# text MIME types. -# CONFIG_THTTPD_IOBUFFERSIZE - -# CONFIG_THTTPD_INDEX_NAMES - A list of index filenames to check. The -# files are searched for in this order. -# CONFIG_AUTH_FILE - The file to use for authentication. If this is -# defined then thttpd checks for this file in the local directory -# before every fetch. If the file exists then authentication is done, -# otherwise the fetch proceeds as usual. If you leave this undefined -# then thttpd will not implement authentication at all and will not -# check for auth files, which saves a bit of CPU time. A typical -# value is ".htpasswd" -# CONFIG_THTTPD_LISTEN_BACKLOG - The listen() backlog queue length. -# CONFIG_THTTPD_LINGER_MSEC - How many milliseconds to leave a connection -# open while doing a lingering close. -# CONFIG_THTTPD_OCCASIONAL_MSEC - How often to run the occasional -# cleanup job. -# CONFIG_THTTPD_IDLE_READ_LIMIT_SEC - How many seconds to allow for -# reading the initial request on a new connection. -# CONFIG_THTTPD_IDLE_SEND_LIMIT_SEC - How many seconds before an -# idle connection gets closed. -# CONFIG_THTTPD_TILDE_MAP1 and CONFIG_THTTPD_TILDE_MAP2 - Tilde mapping. -# Many URLs use ~username to indicate a user's home directory. thttpd -# provides two options for mapping this construct to an actual filename. -# 1) Map ~username to <prefix>/username. This is the recommended choice. -# Each user gets a subdirectory in the main web tree, and the tilde -# construct points there. The prefix could be something like "users", -# or it could be empty. -# 2) Map ~username to <user's homedir>/<postfix>. The postfix would be -# the name of a subdirectory off of the user's actual home dir, -# something like "public_html". -# You can also leave both options undefined, and thttpd will not do -# anything special about tildes. Enabling both options is an error. -# Typical values, if they're defined, are "users" for -# CONFIG_THTTPD_TILDE_MAP1 and "public_html"forCONFIG_THTTPD_TILDE_MAP2. -# CONFIG_THTTPD_GENERATE_INDICES -# CONFIG_THTTPD_URLPATTERN - If defined, then it will be used to match -# and verify referrers. -# CONFIG_THTTPD_PORT=80 CONFIG_THTTPD_IPADDR=0x0a000002 CONFIG_THTTPD_SERVER_ADDRESS="http://www.nuttx.org" @@ -845,18 +425,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -876,12 +444,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -898,36 +460,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -963,15 +495,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -986,26 +509,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/thttpd/defconfig b/nuttx/configs/olimex-lpc1766stk/thttpd/defconfig index 52277615d..6a99e0da9 100755 --- a/nuttx/configs/olimex-lpc1766stk/thttpd/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/thttpd/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=y CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,24 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -216,19 +151,6 @@ CONFIG_NET_REGDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -238,93 +160,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -356,15 +191,6 @@ CONFIG_SIG_SIGWORK=4 # # Settings for nxflat -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals -# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and -# CONFIG_DEBUG_BINFMT have to be defined or -# CONFIG_NXFLAT_DUMPBUFFER does nothing. -# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table -# is ordered by symbol name # CONFIG_NXFLAT=y CONFIG_NXFLAT_DUMPBUFFER=n @@ -397,9 +223,6 @@ CONFIG_DISABLE_POLL=n # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -422,38 +245,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=0 @@ -471,46 +262,6 @@ CONFIG_PREALLOC_TIMERS=8 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -521,13 +272,6 @@ CONFIG_FS_ROMFS=y # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -535,53 +279,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=y CONFIG_NET_IPv6=n @@ -607,8 +316,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -616,22 +323,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -644,19 +335,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -666,26 +344,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -702,26 +360,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -740,61 +378,6 @@ CONFIG_USBMSC_REMOVABLE=y # # THTTPD settings # -# CONFIG_THTTPD_PORT - THTTPD Server port number -# CONFIG_THTTPD_IPADDR - Server IP address (no host name) -# CONFIG_THTTPD_SERVER_ADDRESS - SERVER_ADDRESS: response -# CONFIG_THTTPD_SERVER_SOFTWARE - SERVER_SOFTWARE: response -# CONFIG_THTTPD_PATH - Server working directory -# CONFIG_THTTPD_CGI_PATH - Path to CGI executables -# CONFIG_THTTPD_CGI_PATTERN - Only CGI programs matching this -# pattern will be executed. In fact, if this value is not defined -# then no CGI logic will be built. -# CONFIG_THTTPD_CGI_PRIORITY - Provides the priority of CGI child tasks -# CONFIG_THTTPD_CGI_STACKSIZE - Provides the initial stack size of -# CGI child task (will be overridden by the stack size in the NXFLAT -# header) -# CONFIG_THTTPD_CGI_BYTECOUNT - Byte output limit for CGI tasks. -# CONFIG_THTTPD_CGI_TIMELIMIT - How many seconds to allow CGI programs -# to run before killing them. -# CONFIG_THTTPD_CHARSET- The default character set name to use with -# text MIME types. -# CONFIG_THTTPD_IOBUFFERSIZE - -# CONFIG_THTTPD_INDEX_NAMES - A list of index filenames to check. The -# files are searched for in this order. -# CONFIG_AUTH_FILE - The file to use for authentication. If this is -# defined then thttpd checks for this file in the local directory -# before every fetch. If the file exists then authentication is done, -# otherwise the fetch proceeds as usual. If you leave this undefined -# then thttpd will not implement authentication at all and will not -# check for auth files, which saves a bit of CPU time. A typical -# value is ".htpasswd" -# CONFIG_THTTPD_LISTEN_BACKLOG - The listen() backlog queue length. -# CONFIG_THTTPD_LINGER_MSEC - How many milliseconds to leave a connection -# open while doing a lingering close. -# CONFIG_THTTPD_OCCASIONAL_MSEC - How often to run the occasional -# cleanup job. -# CONFIG_THTTPD_IDLE_READ_LIMIT_SEC - How many seconds to allow for -# reading the initial request on a new connection. -# CONFIG_THTTPD_IDLE_SEND_LIMIT_SEC - How many seconds before an -# idle connection gets closed. -# CONFIG_THTTPD_TILDE_MAP1 and CONFIG_THTTPD_TILDE_MAP2 - Tilde mapping. -# Many URLs use ~username to indicate a user's home directory. thttpd -# provides two options for mapping this construct to an actual filename. -# 1) Map ~username to <prefix>/username. This is the recommended choice. -# Each user gets a subdirectory in the main web tree, and the tilde -# construct points there. The prefix could be something like "users", -# or it could be empty. -# 2) Map ~username to <user's homedir>/<postfix>. The postfix would be -# the name of a subdirectory off of the user's actual home dir, -# something like "public_html". -# You can also leave both options undefined, and thttpd will not do -# anything special about tildes. Enabling both options is an error. -# Typical values, if they're defined, are "users" for -# CONFIG_THTTPD_TILDE_MAP1 and "public_html"forCONFIG_THTTPD_TILDE_MAP2. -# CONFIG_THTTPD_GENERATE_INDICES -# CONFIG_THTTPD_URLPATTERN - If defined, then it will be used to match -# and verify referrers. -# CONFIG_THTTPD_PORT=80 CONFIG_THTTPD_IPADDR=0x0a000002 CONFIG_THTTPD_SERVER_ADDRESS="http://www.nuttx.org" @@ -837,18 +420,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -868,12 +439,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -890,36 +455,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -955,15 +490,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -978,26 +504,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/usbserial/defconfig b/nuttx/configs/olimex-lpc1766stk/usbserial/defconfig index 27f879390..bd7bab899 100755 --- a/nuttx/configs/olimex-lpc1766stk/usbserial/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/usbserial/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,22 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -213,19 +150,6 @@ CONFIG_PHY_FDUPLEX=y # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -235,96 +159,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -382,9 +216,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -407,38 +238,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -456,46 +255,6 @@ CONFIG_PREALLOC_TIMERS=4 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -506,13 +265,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -520,53 +272,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=n CONFIG_NET_IPv6=n @@ -590,8 +307,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -599,22 +314,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=y CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -627,19 +326,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -649,26 +335,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=y CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -685,26 +351,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -730,18 +376,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -761,12 +395,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -783,36 +411,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -848,15 +446,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -871,38 +460,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Settings for examples/usbstorage # -# CONFIG_EXAMPLES_USBMSC_NLUNS -# Defines the number of logical units (LUNs) exported by the USB storage -# driver. Each LUN corresponds to one exported block driver (or partition -# of a block driver). May be 1, 2, or 3. Default is 1. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR1 -# The minor device number of the block driver for the first LUN. For -# example, N in /dev/mmcsdN. Used for registering the block driver. Default -# is zero. -# CONFIG_EXAMPLES_USBMSC_DEVPATH1 -# The full path to the registered block driver. Default is "/dev/mmcsd0" -# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 2 or 3. No defaults. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 3. No defaults. -# -# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then -# the example code will also manage the USB trace output. The amount of trace output -# can be controlled using: -# -# CONFIG_EXAMPLES_USBMSC_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_USBMSC_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_USBMSC_NLUNS=1 CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0 CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0" @@ -915,26 +472,6 @@ CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig b/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig index 42f6dfac7..1a94fef66 100755 --- a/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=n @@ -140,17 +104,6 @@ CONFIG_ARCH_IRQBUTTONS=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -189,22 +142,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -213,19 +150,6 @@ CONFIG_PHY_FDUPLEX=y # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -235,96 +159,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -382,9 +216,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -407,38 +238,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -456,46 +255,6 @@ CONFIG_PREALLOC_TIMERS=4 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -506,13 +265,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -520,53 +272,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=n CONFIG_NET_IPv6=n @@ -590,8 +307,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -599,22 +314,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=y CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -627,19 +326,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -649,26 +335,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -685,26 +351,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=y CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -730,18 +376,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -761,12 +395,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for examples/buttons # -# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX -# Lowest and highest button number (0-7) -# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX -# Lowest and highest interrupting button number (-7) -# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n -# CONFIG_EXAMPLE_BUTTONS_MIN=0 CONFIG_EXAMPLE_BUTTONS_MAX=7 CONFIG_EXAMPLE_IRQBUTTONS_MIN=0 @@ -783,36 +411,6 @@ CONFIG_EXAMPLE_BUTTONS_NAME7="RIGHT" # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -848,15 +446,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -871,38 +460,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Settings for examples/usbstorage # -# CONFIG_EXAMPLES_USBMSC_NLUNS -# Defines the number of logical units (LUNs) exported by the USB storage -# driver. Each LUN corresponds to one exported block driver (or partition -# of a block driver). May be 1, 2, or 3. Default is 1. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR1 -# The minor device number of the block driver for the first LUN. For -# example, N in /dev/mmcsdN. Used for registering the block driver. Default -# is zero. -# CONFIG_EXAMPLES_USBMSC_DEVPATH1 -# The full path to the registered block driver. Default is "/dev/mmcsd0" -# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 2 or 3. No defaults. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 3. No defaults. -# -# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then -# the example code will also manage the USB trace output. The amount of trace output -# can be controlled using: -# -# CONFIG_EXAMPLES_USBMSC_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_USBMSC_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_USBMSC_NLUNS=1 CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0 CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0" @@ -915,26 +472,6 @@ CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n diff --git a/nuttx/configs/olimex-lpc1766stk/wlan/defconfig b/nuttx/configs/olimex-lpc1766stk/wlan/defconfig index 769185afc..73a30a7f7 100755 --- a/nuttx/configs/olimex-lpc1766stk/wlan/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/wlan/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -96,10 +63,7 @@ CONFIG_LPC17_DEVKITARM=n CONFIG_LPC17_BUILDROOT=y # -# Individual subsystems can be enabled: -# # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=y @@ -134,17 +98,6 @@ CONFIG_LPC17_GPDMA=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=y CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -183,24 +136,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. -# Also needs CONFIG_DEBUG. -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=y CONFIG_PHY_AUTONEG=y CONFIG_PHY_SPEED100=n @@ -210,19 +145,6 @@ CONFIG_NET_REGDEBUG=n # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -232,98 +154,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_DEBUG_NET - enable network debug output -# CONFIG_DEBUG_USB - enable usb debug output -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -382,9 +212,6 @@ CONFIG_DISABLE_POLL=n # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -407,38 +234,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -456,46 +251,6 @@ CONFIG_PREALLOC_TIMERS=4 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 -# file name support. -# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims -# patents on FAT long file name technology. Please read the -# disclaimer in the top-level COPYING file and only enable this -# feature if you understand these issues. -# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the -# default, maximum long file name is 255 bytes. This can eat up -# a lot of memory (especially stack space). If you are willing -# to live with some non-standard, short long file names, then -# define this value. A good choice would be the same value as -# selected for CONFIG_NAME_MAX which will limit the visibility -# of longer file names anyway. -# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. -# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. -# This must have one of the values of 0xff or 0x00. -# Default: 0xff. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. -# Default: 255. -# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, -# don't both with file chunks smaller than this number of data bytes. -# Default: 32. -# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean -# packing files together toward the end of the file or, if file are -# deleted at the end of the file, clean up can simply mean erasing -# the end of FLASH memory so that it can be re-used again. However, -# doing this can also harm the life of the FLASH part because it can -# mean that the tail end of the FLASH is re-used too often. This -# threshold determines if/when it is worth erased the tail end of FLASH -# and making it available for re-use (and possible over-wear). -# Default: 8192. -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this -# option will enable a limited form of memory mapping that is -# implemented by copying whole files into memory. -# CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n @@ -506,13 +261,6 @@ CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -520,56 +268,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_NOINTS - uIP not called from interrupt level. -# CONFIG_NET_MULTIBUFFER - Use multiple input/output buffers (probably no) -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates -# CONFIG_NET_WLAN - Enable or disable WLAN network interface # CONFIG_NET=y CONFIG_NET_NOINTS=y @@ -596,8 +306,6 @@ CONFIG_NET_WLAN=y # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -605,22 +313,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -633,20 +325,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # USB Host Configuration # -# CONFIG_USBHOST -# Enables USB host support -# CONFIG_USBHOST_NPREALLOC -# Number of pre-allocated class instances -# CONFIG_USBHOST_BULK_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling bulk endpoint support -# CONFIG_USBHOST_INT_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling interrupt endpoint support -# CONFIG_USBHOST_ISOC_DISABLE -# On some architectures, selecting this setting will reduce driver size -# by disabling isochronous endpoint support -# CONFIG_USBHOST=y CONFIG_USBHOST_NPREALLOC=0 CONFIG_USBHOST_BULK_DISABLE=n @@ -656,19 +334,6 @@ CONFIG_USBHOST_ISOC_DISABLE=y # # LPC17xx USB Device Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -679,18 +344,6 @@ CONFIG_LPC17_USBDEV_DMAINTMASK=0 # LPC17xx USB Host Configuration # # OHCI RAM layout: -# CONFIG_USBHOST_OHCIRAM_SIZE -# Total size of OHCI RAM (in AHB SRAM Bank 1) -# CONFIG_USBHOST_NEDS -# Number of endpoint descriptors -# CONFIG_USBHOST_NTDS -# Number of transfer descriptors -# CONFIG_USBHOST_TDBUFFERS -# Number of transfer descriptor buffers -# CONFIG_USBHOST_TDBUFSIZE -# Size of one transfer descriptor buffer -# CONFIG_USBHOST_IOBUFSIZE -# Size of one end-user I/O buffer # CONFIG_USBHOST_OHCIRAM_SIZE=2048 CONFIG_USBHOST_NEDS=3 @@ -702,26 +355,6 @@ CONFIG_USBHOST_IOBUFSIZE=448 # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -738,26 +371,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -783,18 +396,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) # CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n @@ -823,36 +424,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -888,15 +459,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -911,26 +473,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n |