diff options
Diffstat (limited to 'src/drivers/px4fmu/fmu.cpp')
| -rw-r--r-- | src/drivers/px4fmu/fmu.cpp | 58 |
1 files changed, 55 insertions, 3 deletions
diff --git a/src/drivers/px4fmu/fmu.cpp b/src/drivers/px4fmu/fmu.cpp index b28d318d7..0fbd84924 100644 --- a/src/drivers/px4fmu/fmu.cpp +++ b/src/drivers/px4fmu/fmu.cpp @@ -626,7 +626,7 @@ PX4FMU::task_main() #ifdef HRT_PPM_CHANNEL // see if we have new PPM input data - if (ppm_last_valid_decode != rc_in.timestamp) { + if (ppm_last_valid_decode != rc_in.timestamp_last_signal) { // we have a new PPM frame. Publish it. rc_in.channel_count = ppm_decoded_channels; @@ -638,7 +638,15 @@ PX4FMU::task_main() rc_in.values[i] = ppm_buffer[i]; } - rc_in.timestamp = ppm_last_valid_decode; + rc_in.timestamp_publication = ppm_last_valid_decode; + rc_in.timestamp_last_signal = ppm_last_valid_decode; + + rc_in.rc_ppm_frame_length = ppm_frame_length; + rc_in.rssi = RC_INPUT_RSSI_MAX; + rc_in.rc_failsafe = false; + rc_in.rc_lost = false; + rc_in.rc_lost_frame_count = 0; + rc_in.rc_total_frame_count = 0; /* lazily advertise on first publication */ if (to_input_rc == 0) { @@ -1006,6 +1014,40 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg) break; + case PWM_SERVO_SET_COUNT: { + /* change the number of outputs that are enabled for + * PWM. This is used to change the split between GPIO + * and PWM under control of the flight config + * parameters. Note that this does not allow for + * changing a set of pins to be used for serial on + * FMUv1 + */ + switch (arg) { + case 0: + set_mode(MODE_NONE); + break; + + case 2: + set_mode(MODE_2PWM); + break; + + case 4: + set_mode(MODE_4PWM); + break; + +#if defined(CONFIG_ARCH_BOARD_PX4FMU_V2) + case 6: + set_mode(MODE_6PWM); + break; +#endif + + default: + ret = -EINVAL; + break; + } + break; + } + case MIXERIOCRESET: if (_mixers != nullptr) { delete _mixers; @@ -1108,10 +1150,12 @@ PX4FMU::sensor_reset(int ms) stm32_configgpio(GPIO_SPI_CS_GYRO_OFF); stm32_configgpio(GPIO_SPI_CS_ACCEL_MAG_OFF); stm32_configgpio(GPIO_SPI_CS_BARO_OFF); + stm32_configgpio(GPIO_SPI_CS_MPU_OFF); stm32_gpiowrite(GPIO_SPI_CS_GYRO_OFF, 0); stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG_OFF, 0); stm32_gpiowrite(GPIO_SPI_CS_BARO_OFF, 0); + stm32_gpiowrite(GPIO_SPI_CS_MPU_OFF, 0); stm32_configgpio(GPIO_SPI1_SCK_OFF); stm32_configgpio(GPIO_SPI1_MISO_OFF); @@ -1124,10 +1168,12 @@ PX4FMU::sensor_reset(int ms) stm32_configgpio(GPIO_GYRO_DRDY_OFF); stm32_configgpio(GPIO_MAG_DRDY_OFF); stm32_configgpio(GPIO_ACCEL_DRDY_OFF); + stm32_configgpio(GPIO_EXTI_MPU_DRDY_OFF); stm32_gpiowrite(GPIO_GYRO_DRDY_OFF, 0); stm32_gpiowrite(GPIO_MAG_DRDY_OFF, 0); stm32_gpiowrite(GPIO_ACCEL_DRDY_OFF, 0); + stm32_gpiowrite(GPIO_EXTI_MPU_DRDY_OFF, 0); /* set the sensor rail off */ stm32_configgpio(GPIO_VDD_3V3_SENSORS_EN); @@ -1160,6 +1206,13 @@ PX4FMU::sensor_reset(int ms) stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG, 1); stm32_gpiowrite(GPIO_SPI_CS_BARO, 1); stm32_gpiowrite(GPIO_SPI_CS_MPU, 1); + + // // XXX bring up the EXTI pins again + // stm32_configgpio(GPIO_GYRO_DRDY); + // stm32_configgpio(GPIO_MAG_DRDY); + // stm32_configgpio(GPIO_ACCEL_DRDY); + // stm32_configgpio(GPIO_EXTI_MPU_DRDY); + #endif #endif } @@ -1432,7 +1485,6 @@ void sensor_reset(int ms) { int fd; - int ret; fd = open(PX4FMU_DEVICE_PATH, O_RDWR); |