diff options
Diffstat (limited to 'src')
-rw-r--r-- | src/drivers/meas_airspeed/meas_airspeed.cpp | 49 | ||||
-rw-r--r-- | src/modules/uORB/topics/differential_pressure.h | 9 |
2 files changed, 43 insertions, 15 deletions
diff --git a/src/drivers/meas_airspeed/meas_airspeed.cpp b/src/drivers/meas_airspeed/meas_airspeed.cpp index 0b7986383..58b128948 100644 --- a/src/drivers/meas_airspeed/meas_airspeed.cpp +++ b/src/drivers/meas_airspeed/meas_airspeed.cpp @@ -206,20 +206,46 @@ MEASAirspeed::collect() dT_raw = (0xFFE0 & dT_raw) >> 5; float temperature = ((200.0f * dT_raw) / 2047) - 50; - /* calculate differential pressure. As its centered around 8000 - * and can go positive or negative, enforce absolute value - */ + // Calculate differential pressure. As its centered around 8000 + // and can go positive or negative const float P_min = -1.0f; const float P_max = 1.0f; - float diff_press_pa = fabsf((((float)dp_raw - 0.1f * 16383.0f) * (P_max - P_min) / (0.8f * 16383.0f) + P_min) * 6894.8f) - _diff_pres_offset; + const float PSI_to_Pa = 6894.757f; + /* + this equation is an inversion of the equation in the + pressure transfer function figure on page 4 of the datasheet - if (diff_press_pa < 0.0f) { - diff_press_pa = 0.0f; - } + We negate the result so that positive differential pressures + are generated when the bottom port is used as the static + port on the pitot and top port is used as the dynamic port + */ + float diff_press_PSI = -((dp_raw - 0.1f*16383) * (P_max-P_min)/(0.8f*16383) + P_min); + float diff_press_pa_raw = diff_press_PSI * PSI_to_Pa; // correct for 5V rail voltage if possible - voltage_correction(diff_press_pa, temperature); + voltage_correction(diff_press_pa_raw, temperature); + float diff_press_pa = fabsf(diff_press_pa_raw - _diff_pres_offset); + + /* + note that we return both the absolute value with offset + applied and a raw value without the offset applied. This + makes it possible for higher level code to detect if the + user has the tubes connected backwards, and also makes it + possible to correctly use offsets calculated by a higher + level airspeed driver. + + With the above calculation the MS4525 sensor will produce a + positive number when the top port is used as a dynamic port + and bottom port is used as the static port + + Also note that the _diff_pres_offset is applied before the + fabsf() not afterwards. It needs to be done this way to + prevent a bias at low speeds, but this also means that when + setting a offset you must set it based on the raw value, not + the offset value + */ + struct differential_pressure_s report; /* track maximum differential pressure measured (so we can work out top speed). */ @@ -232,6 +258,7 @@ MEASAirspeed::collect() report.temperature = temperature; report.differential_pressure_pa = diff_press_pa; report.differential_pressure_filtered_pa = _filter.apply(diff_press_pa); + report.differential_pressure_raw_pa = diff_press_pa_raw; report.voltage = 0; report.max_differential_pressure_pa = _max_differential_pressure_pa; @@ -328,7 +355,7 @@ MEASAirspeed::voltage_correction(float &diff_press_pa, float &temperature) return; } - const float slope = 70.0f; + const float slope = 65.0f; /* apply a piecewise linear correction, flattening at 0.5V from 5V */ @@ -478,7 +505,7 @@ test() } warnx("single read"); - warnx("diff pressure: %8.4f pa", (double)report.differential_pressure_pa); + warnx("diff pressure: %d pa", (int)report.differential_pressure_pa); /* start the sensor polling at 2Hz */ if (OK != ioctl(fd, SENSORIOCSPOLLRATE, 2)) { @@ -506,7 +533,7 @@ test() } warnx("periodic read %u", i); - warnx("diff pressure: %8.4f pa", (double)report.differential_pressure_pa); + warnx("diff pressure: %d pa", (int)report.differential_pressure_pa); warnx("temperature: %d C (0x%02x)", (int)report.temperature, (unsigned) report.temperature); } diff --git a/src/modules/uORB/topics/differential_pressure.h b/src/modules/uORB/topics/differential_pressure.h index ff88b04c6..01e14cda9 100644 --- a/src/modules/uORB/topics/differential_pressure.h +++ b/src/modules/uORB/topics/differential_pressure.h @@ -52,13 +52,14 @@ * Differential pressure. */ struct differential_pressure_s { - uint64_t timestamp; /**< microseconds since system boot, needed to integrate */ - uint64_t error_count; + uint64_t timestamp; /**< Microseconds since system boot, needed to integrate */ + uint64_t error_count; /**< Number of errors detected by driver */ float differential_pressure_pa; /**< Differential pressure reading */ + float differential_pressure_raw_pa; /**< Raw differential pressure reading (may be negative) */ float differential_pressure_filtered_pa; /**< Low pass filtered differential pressure reading */ float max_differential_pressure_pa; /**< Maximum differential pressure reading */ - float voltage; /**< Voltage from analog airspeed sensors (voltage divider already compensated) */ - float temperature; /**< Temperature provided by sensor, -1000.0f if unknown */ + float voltage; /**< Voltage from analog airspeed sensors (voltage divider already compensated) */ + float temperature; /**< Temperature provided by sensor, -1000.0f if unknown */ }; |