path: root/nuttx/include/nuttx/net/mii.h

/****************************************************************************
 * include/nuttx/net/mii.h
 *
 *   Copyright (C) 2008-2010, 2012 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ****************************************************************************/

#ifndef __INCLUDE_NUTTX_NET_MII_H
#define __INCLUDE_NUTTX_NET_MII_H

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>

/****************************************************************************
 * Pre-Processor Definitions
 ****************************************************************************/

/* MII register offsets *****************************************************/

/* Common MII management registers. The IEEE 802.3 standard specifies a
 * register set for controlling and gathering status from the PHY layer. The
 * registers are collectively known as the MII Management registers and are
 * detailed in Section 22.2.4 of the IEEE 802.3 specification.
 */

#define MII_MCR                      0x00      /* MII management control */
#define MII_MSR                      0x01      /* MII management status */
#define MII_PHYID1                   0x02      /* PHY ID 1 */
#define MII_PHYID2                   0x03      /* PHY ID 2 */
#define MII_ADVERTISE                0x04      /* Auto-negotiation advertisement */
#define MII_LPA                      0x05      /* Auto-negotiation link partner base page ability */
#define MII_EXPANSION                0x06      /* Auto-negotiation expansion */
#define MII_NEXTPAGE                 0x07      /* Auto-negotiation next page */
#define MII_LPANEXTPAGE              0x08      /* Auto-negotiation link partner received next page */
#define MII_MSCONTROL                0x09      /* Master/slave control register */
#define MII_MSSTATUS                 0x0a      /* Master/slave status register */
#define MII_PSECONTROL               0x0b      /* PSE control register */
#define MII_PSESTATUS                0x0c      /* PSE status register */
#define MII_MMDCONTROL               0x0d      /* MMD access control register */
#define MII_ESTATUS                  0x0f      /* Extended status register */

/* Extended Registers: Registers 16-31 may be used for vendor specific abilities */

/* National Semiconductor DP83840: 0x07-0x11, 0x14, 0x1a, 0x1d-0x1f reserved */

#define MII_DP83840_COUNTER          0x12      /* Disconnect counter */
#define MII_DP83840_FCSCOUNTER       0x13      /* False carrier sense counter */
#define MII_DP83840_NWAYTEST         0x14      /* N-way auto-neg test reg */
#define MII_DP83840_RERRCOUNTER      0x15      /* Receive error counter */
#define MII_DP83840_SREVISION        0x16      /* Silicon revision */
#define MII_DP83840_LBRERROR         0x18      /* Loopback, bypass and receiver error */
#define MII_DP83840_PHYADDR          0x19      /* PHY address */
#define MII_DP83840_10BTSR           0x1b      /* 10BASE-T status register */
#define MII_DP83840_10BTCR           0x1c      /* 10BASE-T configuration register */

/* National Semiconductor DP83848C: 0x8-0x15, 0x13, 0x1c reserved */

#define MII_DP83848C_PHYSTS          0x10      /* RO PHY Status Register */
#define MII_DP83848C_MICR            0x11      /* RW MII Interrupt Control Register */
#define MII_DP83848C_MISR            0x12      /* RO MII Interrupt Status Register */
#define MII_DP83848C_FCSCR           0x14      /* RO False Carrier Sense Counter Register */
#define MII_DP83848C_RECR            0x15      /* RO Receive Error Counter Register */
#define MII_DP83848C_PCSR            0x16      /* RW PCS Sub-Layer Configuration and Status Register */
#define MII_DP83848C_RBR             0x17      /* RW RMII and Bypass Register */
#define MII_DP83848C_LEDCR           0x18      /* RW LED Direct Control Register */
#define MII_DP83848C_PHYCR           0x19      /* RW PHY Control Register */
#define MII_DP83848C_10BTSCR         0x1a      /* RW 10Base-T Status/Control Register */
#define MII_DP83848C_CDCTRL1         0x1b      /* RW CD Test Control Register and BIST Extensions Register */
#define MII_DP83848C_EDCR            0x1e      /* RW Energy Detect */

/* Am79c874: 0x08-0x0f, 0x14, 0x16, 0x19-0x1f reserved */

#define MII_AM79C874_NPADVERTISE     0x07      /* Auto-negotiation next page advertisement */
#define MII_AM79C874_MISCFEATURES    0x10      /* Miscellaneous features reg */
#define MII_AM79C874_INTCS           0x11      /* Interrupt control/status */
#define MII_AM79C874_DIAGNOSTIC      0x12      /* Diagnostic */
#define MII_AM79C874_LOOPBACK        0x13      /* Power management/loopback */
#define MII_AM79C874_MODEC           0x15      /* Mode control register */
#define MII_AM79C874_DISCONNECT      0x17      /* Disconnect counter */
#define MII_AM79C874_RCVERROR        0x18      /* Receive error counter */

/* Luminary LM3S6918 built-in PHY: 0x07-0x0f, 0x14-0x16, 0x19-0x1f reserved */

#define MII_LM_VSPECIFIC             0x10      /* Vendor-Specific */
#define MII_LM_INTCS                 0x11      /* Interrupt control/status */
#define MII_LM_DIAGNOSTIC            0x12      /* Diagnostic */
#define MII_LM_XCVRCONTROL           0x13      /* Transceiver Control */
#define MII_LM_LEDCONFIG             0x17      /* LED Configuration */
#define MII_LM_MDICONTROL            0x18      /* Ethernet PHY Management MDI/MDIX Control */

/* Micrel KS8721: 0x15, 0x1b, and 0x1f */

#define MII_KS8721_RXERCOUNTER       0x15      /* RXER counter */
#define MII_KS8721_INTCS             0x1b      /* Interrupt control/status register */
#define MII_KS8721_10BTCR            0x1f      /* 10BASE-TX PHY control register */

/* National Semiconductor DP83848C PHY Extended Registers */

#define MII_DP83848C_STS             0x10      /* Status Register */
#define MII_DP83848C_MICR            0x11      /* MII Interrupt Control Register */
#define MII_DP83848C_MISR            0x12      /* MII Interrupt Status Register */
#define MII_DP83848C_FCSCR           0x14      /* False Carrier Sense Counter */
#define MII_DP83848C_RECR            0x15      /* Receive Error Counter */
#define MII_DP83848C_PCSR            0x16      /* PCS Sublayer Config. and Status */
#define MII_DP83848C_RBR             0x17      /* RMII and Bypass Register */
#define MII_DP83848C_LEDCR           0x18      /* LED Direct Control Register */
#define MII_DP83848C_PHYCR           0x19      /* PHY Control Register */
#define MII_DP83848C_10BTSCR         0x1a      /* 10Base-T Status/Control Register */
#define MII_DP83848C_CDCTRL1         0x1b      /* CD Test Control and BIST Extens */
#define MII_DP83848C_EDCR            0x1d      /* Energy Detect Control Register */

/* SMSC LAN8720 PHY Extended Registers */

#define MII_LAN8720_REV              0x10      /* Silicon Revision Register */
#define MII_LAN8720_MCSR             0x11      /* Mode Control/Status Register */
#define MII_LAN8720_MODES            0x12      /* Special modes */
#define MII_LAN8720_SECR             0x1a      /* Symbol Error Counter Register */
#define MII_LAN8720_CSIR             0x1b      /* Control / Status Indicator Register */
#define MII_LAN8720_SITC             0x1c      /* Special Internal Testability Controls */
#define MII_LAN8720_ISR              0x1d      /* Interrupt Source Register */
#define MII_LAN8720_IMR              0x1e      /* Interrupt Mask Register */
#define MII_LAN8720_SCSR             0x1f      /* PHY Special Control/Status Register */

/* GMII */

#define GMII_MCR                     MII_MCR         /* GMII management control */
#define GMII_MSR                     MII_MSR         /* GMII management status */
#define GMII_PHYID1                  MII_PHYID1      /* PHY ID 1 */
#define GMII_PHYID2                  MII_PHYID2      /* PHY ID 2 */
#define GMII_ADVERTISE               MII_ADVERTISE   /* Auto-negotiation advertisement */
#define GMII_LPA                     MII_LPA         /* Auto-negotiation link partner base page ability */
#define GMII_EXPANSION               MII_EXPANSION   /* Auto-negotiation expansion */
#define GMII_NEXTPAGE                MII_NEXTPAGE    /* Auto-negotiation next page */
#define GMII_LPANEXTPAGE             MII_LPANEXTPAGE /* Auto-negotiation link partner received next page */
#define GMII_CTRL1000                0x09            /* 1000BASE-T control */
#define GMII_STAT1000                0x0a            /* 1000BASE-T status */
#define GMII_ESTATUS                 MII_ESTATUS     /* Extended status register */

/* MII register bit settings ************************************************/

/* MII Control register bit definitions */

#define MII_MCR_UNIDIR               (1 << 5)  /* Bit 5:  Unidirectional enable */
#define MII_MCR_SPEED1000            (1 << 6)  /* Bit 6:  MSB of Speed (1000 reserved on 10/100) */
#define MII_MCR_CTST                 (1 << 7)  /* Bit 7:  Enable collision test  */
#define MII_MCR_FULLDPLX             (1 << 8)  /* Bit 8:  Full duplex */
#define MII_MCR_ANRESTART            (1 << 9)  /* Bit 9:  Restart auto negotiation */
#define MII_MCR_ISOLATE              (1 << 10) /* Bit 10: Electronically isolate PHY from MII */
#define MII_MCR_PDOWN                (1 << 11) /* Bit 11: Powerdown the PHY */
#define MII_MCR_ANENABLE             (1 << 12) /* Bit 12: Enable auto negotiation */
#define MII_MCR_SPEED100             (1 << 13) /* Bit 13: Select 100Mbps */
#define MII_MCR_LOOPBACK             (1 << 14) /* Bit 14: Enable loopback mode */
#define MII_MCR_RESET                (1 << 15) /* Bit 15: PHY reset */

/* MII Status register bit definitions */

#define MII_MSR_EXTCAP               (1 << 0)  /* Bit 0:  Extended register capability */
#define MII_MSR_JABBERDETECT         (1 << 1)  /* Bit 1:  Jabber detect */
#define MII_MSR_LINKSTATUS           (1 << 2)  /* Bit 2:  Link status */
#define MII_MSR_ANEGABLE             (1 << 3)  /* Bit 3:  Auto-negotiation able */
#define MII_MSR_RFAULT               (1 << 4)  /* Bit 4:  Remote fault */
#define MII_MSR_ANEGCOMPLETE         (1 << 5)  /* Bit 5:  Auto-negotiation complete */
#define MII_MSR_MFRAMESUPPRESS       (1 << 6)  /* Bit 6:  Management frame suppression */
#define MII_MSR_ESTATEN              (1 << 8)  /* Bit 8:  Extended Status in R15 */
#define MII_MSR_100BASET2FULL        (1 << 9)  /* Bit 9:  100BASE-T2 half duplex able */
#define MII_MSR_100BASET2HALF        (1 << 10) /* Bit 10: 100BASE-T2 full duplex able */
#define MII_MSR_10BASETXHALF         (1 << 11) /* Bit 11: 10BASE-TX half duplex able */
#define MII_MSR_10BASETXFULL         (1 << 12) /* Bit 12: 10BASE-TX full duplex able */
#define MII_MSR_100BASETXHALF        (1 << 13) /* Bit 13: 100BASE-TX half duplex able */
#define MII_MSR_100BASETXFULL        (1 << 14) /* Bit 14: 100BASE-TX full duplex able */
#define MII_MSR_100BASET4            (1 << 15) /* Bit 15: 100BASE-T4 able */

/* MII ID2 register bits */

#define MII_PHYID2_OUI               0xfc00    /* Bits 19-24 of OUI mask */
#define MII_PHYID2_MODEL             0x03f0    /* Model number mask */
#define MII_PHYID2_REV               0x000f    /* Revision number mask */

/* Advertisement control register bit definitions */

#define MII_ADVERTISE_SELECT         0x001f    /* Bits 0-4: Selector field */
#define MII_ADVERTISE_CSMA           (1 << 0)  /*         CSMA */
#define MII_ADVERTISE_8023           (1 << 0)  /*         IEEE Std 802.3 */
#define MII_ADVERTISE_8029           (2 << 0)  /*         IEEE Std 802.9 ISLAN-16T */
#define MII_ADVERTISE_8025           (3 << 0)  /*         IEEE Std 802.5 */
#define MII_ADVERTISE_1394           (4 << 0)  /*         IEEE Std 1394 */
#define MII_ADVERTISE_10BASETXHALF   (1 << 5)  /* Bit 5:  Try 10BASE-TX half duplex */
#define MII_ADVERTISE_1000XFULL      (1 << 5)  /* Bit 5:  Try 1000BASE-X full duplex */
#define MII_ADVERTISE_10BASETXFULL   (1 << 6)  /* Bit 6:  Try 10BASE-TX full duplex */
#define MII_ADVERTISE_1000XHALF      (1 << 6)  /* Bit 6:  Try 1000BASE-X half duplex */
#define MII_ADVERTISE_100BASETXHALF  (1 << 7)  /* Bit 7:  Try 100BASE-TX half duplex */
#define MII_ADVERTISE_1000XPAUSE     (1 << 7)  /* Bit 7:  Try 1000BASE-X pause */
#define MII_ADVERTISE_100BASETXFULL  (1 << 8)  /* Bit 8:  Try 100BASE-TX full duplex*/
#define MII_ADVERTISE_1000XASYMPAU   (1 << 8)  /* Bit 8:  Try 1000BASE-X asym pause */
#define MII_ADVERTISE_100BASET4      (1 << 9)  /* Bit 9:  Try 100BASE-T4 */
#define MII_ADVERTISE_FDXPAUSE       (1 << 10) /* Bit 10: Try full duplex flow control */
#define MII_ADVERTISE_ASYMPAUSE      (1 << 11) /* Bit 11: Try asymetric pause */
#define MII_ADVERTISE_RFAULT         (1 << 13) /* Bit 13: Remote fault supported */
#define MII_ADVERTISE_LPACK          (1 << 14) /* Bit 14: Ack link partners response */
#define MII_ADVERTISE_NXTPAGE        (1 << 15) /* Bit 15: Next page enabled */

/* Link partner ability register bit definitions */

#define MII_LPA_SELECT               0x001f    /* Bits 0-4: Link partner selector field */
#define MII_LPA_CSMA                 (1 << 0)  /*         CSMA */
#define MII_LPA_8023                 (1 << 0)  /*         IEEE Std 802.3 */
#define MII_LPA_8029                 (2 << 0)  /*         IEEE Std 802.9 ISLAN-16T */
#define MII_LPA_8025                 (3 << 0)  /*         IEEE Std 802.5 */
#define MII_LPA_1394                 (4 << 0)  /*         IEEE Std 1394 */
#define MII_LPA_10BASETXHALF         (1 << 5)  /* Bit 5:  10BASE-TX half duplex able */
#define MII_LPA_1000XFULL            (1 << 5)  /* Bit 5:  1000BASE-X full-duplex able */
#define MII_LPA_10BASETXFULL         (1 << 6)  /* Bit 6:  10BASE-TX full duplex able */
#define MII_LPA_1000XHALF            (1 << 6)  /* Bit 6:  1000BASE-X half-duplex */
#define MII_LPA_100BASETXHALF        (1 << 7)  /* Bit 7:  100BASE-TX half duplex able */
#define MII_LPA_1000XPAUSE           (1 << 7)  /* Bit 7:  1000BASE-X pause able */
#define MII_LPA_100BASETXFULL        (1 << 8)  /* Bit 8:  100BASE-TX full duplex able */
#define MII_LPA_1000XASYMPAU         (1 << 8)  /* Bit 8:  1000BASE-X asym pause able */
#define MII_LPA_100BASET4            (1 << 9)  /* Bit 9:  100BASE-T4 able */
#define MII_LPA_FDXPAUSE             (1 << 10) /* Bit 10: Full duplex flow control able */
#define MII_LPA_ASYMPAUSE            (1 << 11) /* Bit 11: Asynchronous pause able */
#define MII_LPA_RFAULT               (1 << 13) /* Bit 13: Link partner remote fault request */
#define MII_LPA_LPACK                (1 << 14) /* Bit 14: Link partner acknowledgement */
#define MII_LPA_NXTPAGE              (1 << 15) /* Bit 15: Next page requested */

/* Link partner ability in next page format */

#define MII_LPANP_MESSAGE            0x07ff    /* Bits 0-10: Link partner's message code */
#define MII_LPANP_TOGGLE             (1 << 11) /* Bit 11: Link partner toggle */
#define MII_LPANP_LACK2              (1 << 12) /* Bit 12: Link partner can comply ACK */
#define MII_LPANP_MSGPAGE            (1 << 13) /* Bit 13: Link partner message page request */
#define MII_LPANP_LPACK              (1 << 14) /* Bit 14: Link partner acknowledgement */
#define MII_LPANP_NXTPAGE            (1 << 15) /* Bit 15: Next page requested */

/* MII Auto-negotiation expansion register bit definitions */

#define MII_EXPANSION_ANEGABLE       (1 << 0)  /* Bit 0: Link partner is auto-negotion able */
#define MII_EXPANSION_PAGERECVD      (1 << 1)  /* Bit 1: New link code word in LPA ability reg */
#define MII_EXPANSION_ENABLENPAGE    (1 << 2)  /* Bit 2: This enables npage words */
#define MII_EXPANSION_NXTPAGEABLE    (1 << 3)  /* Bit 3: Link partner supports next page */
#define MII_EXPANSION_PARFAULTS      (1 << 4)  /* Bit 4: Fault detected by parallel logic */

/* Auto-negotiation next page advertisement */

#define MII_NPADVERTISE_CODE         0x07ff    /* Bits 0-10: message/un-formated code field */
#define MII_NPADVERTISE_TOGGLE       (1 << 11) /* Bit 11: Toggle */
#define MII_NPADVERTISE_ACK2         (1 << 12) /* Bit 12: Acknowledgement 2 */
#define MII_NPADVERTISE_MSGPAGE      (1 << 13) /* Bit 13: Message page */
#define MII_NPADVERTISE_NXTPAGE      (1 << 15) /* Bit 15: Next page indication */

/* MII PHYADDR register bit definitions */

#define DP83840_PHYADDR_DUPLEX       (1 << 7)
#define DP83840_PHYADDR_SPEED        (1 << 6)

/* National Semiconductor DP83848C ******************************************/
/* DP83848C MII ID1/2 register bits */

#define MII_PHYID1_DP83848C          0x2000    /* ID1 value for DP83848C */
#define MII_PHYID2_DP83848C          0x5c90    /* ID2 value for DP83848C */

/* RMII and Bypass Register (0x17) */

#define MII_RBR_ELAST_MASK           0x0003    /* Bits 0-1: Receive elasticity buffer */
#  define MII_RBR_ELAST_14           0x0000    /*   14 bit tolerance */
#  define MII_RBR_ELAST_2            0x0001    /*   2 bit tolerance */
#  define MII_RBR_ELAST_6            0x0002    /*   6 bit tolerance */
#  define MII_RBR_ELAST_10           0x0003    /*   10 bit tolerance */
#define MII_RBR_RXUNFSTS             (1 << 2)  /* Bit 2: RX FIFO underflow */
#define MII_RBR_RXOVFSTS             (1 << 3)  /* Bit 3: RX FIFO overflow */
#define MII_RBR_RMIIREV10            (1 << 4)  /* Bit 4: 0=RMIIv1.2 1-RMIIv1.0 */
#define MII_RBR_RMIIMODE             (1 << 5)  /* Bit 5: 0=MII mode 1=RMII mode */

/* SMSC LAN8720 *************************************************************/
/* SMSC LAN8720 MII ID1/2 register bits */

#define MII_PHYID1_LAN8720           0x0007    /* ID1 value for LAN8720 */
#define MII_PHYID2_LAN8720           0xc0f1    /* ID2 value for LAN8720 */

/* Am79c874-specific register bit settings **********************************/
/* Am79c874 MII ID1/2 register bits */

#define MII_PHYID1_AM79C874          0x0022    /* ID1 value for Am79c874 */
#define MII_PHYID2_AM79C874          0x561b    /* ID2 value for Am79c874 Rev B */

/* Am79c874 diagnostics register */

#define AM79C874_DIAG_RXLOCK         (1 << 8)  /* Bit 8:  1=Rcv PLL locked on */
#define AM79C874_DIAG_RXPASS         (1 << 9)  /* Bit 9:  1=Operating in 100Base-X mode */
#define AM79C874_DIAG_100MBPS        (1 << 10) /* Bit 10: 1=ANEG result is 100Mbps */
#define AM79C874_DIAG_FULLDPLX       (1 << 11) /* Bit 11: 1=ANEG result is full duplex */

/* LM3S6918-specific register bit settings **********************************/
/* LM3S6918 Vendor-Specific, address 0x10 */

#define LM_VSPECIFIC_RXCC            (1 << 0)  /* Bit 0:  Receive Clock Control*/
#define LM_VSPECIFIC_PCSBP           (1 << 1)  /* Bit 1:  PCS Bypass */
#define LM_VSPECIFIC_RVSPOL          (1 << 4)  /* Bit 4:  Receive Data Polarity */
#define LM_VSPECIFIC_APOL            (1 << 5)  /* Bit 5:  Auto-Polarity Disable */
#define LM_VSPECIFIC_NL10            (1 << 10) /* Bit 10: Natural Loopback Mode */
#define LM_VSPECIFIC_SQEI            (1 << 11) /* Bit 11: SQE Inhibit Testing */
#define LM_VSPECIFIC_TXHIM           (1 << 12) /* Bit 12: Transmit High Impedance Mode */
#define LM_VSPECIFIC_INPOL           (1 << 14) /* Bit 14: Interrupt Polarity Value*/
#define LM_VSPECIFIC_RPTR            (1 << 15) /* Bit 15: Repeater mode*/

/* LM3S6918 Interrupt Control/Status, address 0x11 */

#define LM_INTCS_ANEGCOMPINT         (1 << 0)  /* Bit 0:  Auto-Negotiation Complete Interrupt */
#define LM_INTCS_RFAULTINT           (1 << 1)  /* Bit 1:  Remote Fault Interrupt */
#define LM_INTCS_LSCHGINT            (1 << 2)  /* Bit 2:  Link Status Change Interrupt */
#define LM_INTCS_LPACKINT            (1 << 3)  /* Bit 3:  LP Acknowledge Interrupt */
#define LM_INTCS_PDFINT              (1 << 4)  /* Bit 4:  Parallel Detection Fault Interrupt */
#define LM_INTCS_PRXINT              (1 << 5)  /* Bit 5:  Page Receive Interrupt */
#define LM_INTCS_RXERINT             (1 << 6)  /* Bit 6:  Receive Error Interrupt */
#define LM_INTCS_JABBERINT           (1 << 7)  /* Bit 7:  Jabber Event Interrupt */
#define LM_INTCS_ANEGCOMPIE          (1 << 8)  /* Bit 8:  Auto-Negotiation Complete Interrupt Enable */
#define LM_INTCS_RFAULTIE            (1 << 9)  /* Bit 9:  Remote Fault Interrupt Enable */
#define LM_INTCS_LSCHGIE             (1 << 10) /* Bit 10: Link Status Change Interrupt Enable */
#define LM_INTCS_LPACKIE             (1 << 11) /* Bit 11: LP Acknowledge Interrupt Enable */
#define LM_INTCS_PDFIE               (1 << 12) /* Bit 12: Parallel Detection Fault Interrupt Enable */
#define LM_INTCS_PRXIE               (1 << 13) /* Bit 13: Page Received Interrupt Enable */
#define LM_INTCS_RXERIE              (1 << 14) /* Bit 14: Receive Error Interrupt Enable */
#define LM_INTCS_JABBERIE            (1 << 15) /* Bit 15: Jabber Interrupt Enable */

/* LM3S6918 Diagnostic, address 0x12 */

#define LM_DIAGNOSTIC_RX_LOCK        (1 << 8)  /* Bit 8:  Receive PLL Lock */
#define LM_DIAGNOSTIC_RXSD           (1 << 9)  /* Bit 9:  Receive Detection */
#define LM_DIAGNOSTIC_RATE           (1 << 10) /* Bit 10: Rate */
#define LM_DIAGNOSTIC_DPLX           (1 << 11) /* Bit 11: Duplex Mode */
#define LM_DIAGNOSTIC_ANEGF          (1 << 12) /* Bit 12: Auto-Negotiation Failure */

/* LM3S6918 Transceiver Control, address 0x13 */

#define LM_XCVRCONTROL_TXO_SHIFT     14        /* Bits 15-14: Transmit Amplitude Selection */
#define LM_XCVRCONTROL_TXO_MASK      (3 << LM_XCVRCONTROL_TXO_SHIFT)
#define LM_XCVRCONTROL_TXO_00DB      (0 << LM_XCVRCONTROL_TXO_SHIFT) /* Gain 0.0dB of insertion loss */
#define LM_XCVRCONTROL_TXO_04DB      (1 << LM_XCVRCONTROL_TXO_SHIFT) /* Gain 0.4dB of insertion loss */
#define LM_XCVRCONTROL_TXO_08DB      (2 << LM_XCVRCONTROL_TXO_SHIFT) /* Gain 0.8dB of insertion loss */
#define LM_XCVRCONTROL_TXO_12DB      (3 << LM_XCVRCONTROL_TXO_SHIFT) /* Gain 1.2dB of insertion loss */

/* LM3S6918 LED Configuration, address 0x17 */

#define LM_LEDCONFIG_LED0_SHIFT      (0)       /* Bits 3-0: LED0 Source */
#define LM_LEDCONFIG_LED0_MASK       (0x0f << LM_LEDCONFIG_LED0_SHIFT)
#define LM_LEDCONFIG_LED0_LINKOK     (0 << LM_LEDCONFIG_LED0_SHIFT)  /* Link OK */
#define LM_LEDCONFIG_LED0_RXTX       (1 << LM_LEDCONFIG_LED0_SHIFT)  /* RX or TX activity */
#define LM_LEDCONFIG_LED0_100BASET   (5 << LM_LEDCONFIG_LED0_SHIFT)  /* 100BASE-TX mode */
#define LM_LEDCONFIG_LED0_10BASET    (6 << LM_LEDCONFIG_LED0_SHIFT)  /* 10BASE-T mode */
#define LM_LEDCONFIG_LED0_FDUPLEX    (7 << LM_LEDCONFIG_LED0_SHIFT)  /* Full duplex */
#define LM_LEDCONFIG_LED0_OKRXTX     (8 << LM_LEDCONFIG_LED0_SHIFT)  /* Full duplex */
#define LM_LEDCONFIG_LED1_SHIFT      (4)        /* Bits 7-4: LED1 Source */
#define LM_LEDCONFIG_LED1_MASK       (0x0f << LM_LEDCONFIG_LED1_SHIFT)
#define LM_LEDCONFIG_LED1_LINKOK     (0 << LM_LEDCONFIG_LED1_SHIFT)  /* Link OK */
#define LM_LEDCONFIG_LED1_RXTX       (1 << LM_LEDCONFIG_LED1_SHIFT)  /* RX or TX activity */
#define LM_LEDCONFIG_LED1_100BASET   (5 << LM_LEDCONFIG_LED1_SHIFT)  /* 100BASE-TX mode */
#define LM_LEDCONFIG_LED1_10BASET    (6 << LM_LEDCONFIG_LED1_SHIFT)  /* 10BASE-T mode */
#define LM_LEDCONFIG_LED1_FDUPLEX    (7 << LM_LEDCONFIG_LED1_SHIFT)  /* Full duplex */
#define LM_LEDCONFIG_LED1_OKRXTX     (8 << LM_LEDCONFIG_LED1_SHIFT)  /* Full duplex */

/* LM3S6918 MDI/MDIX Control, address 0x18 */

#define LM_MDICONTROL_MDIXSD_SHIFT   (0)        /* Bits 3-0: Auto-Switching Seed */
#define LM_MDICONTROL_MDIXSD_MASK    (0x0f << LM_MDICONTROL_MDIXSD_SHIFT)
#define LM_MDICONTROL_MDIXCM         (1 << 4)  /* Bit 4:  Auto-Switching Complete */
#define LM_MDICONTROL_MDIX           (1 << 5)  /* Bit 5:  Auto-Switching Configuration */
#define LM_MDICONTROL_AUTOSW         (1 << 6)  /* Bit 6:  Auto-Switching Enable */
#define LM_MDICONTROL_PDMODE         (1 << 7)  /* Bit 7:  Parallel Detection Mode */

/* KS8921-specific register bit settings ************************************/
/* KS8921 MII Control register bit definitions (not in 802.3) */

#define KS8721_MCR_DISABXMT          (1 << 0)  /* Bit 0:  Disable Transmitter */

/* KS8921 MII ID1/2 register bits */

#define MII_PHYID1_KS8721            0x0022    /* ID1 value for Micrel KS8721 */
#define MII_PHYID2_KS8721            0x1619    /* ID2 value for Micrel KS8721 */

/* KS8921 RXER Counter -- 16-bit counter */

/* KS8921 Interrupt Control/Status Register */

#define KS8721_INTCS_LINKUP          (1 << 0)  /* Bit 0:  Link up occurred */
#define KS8721_INTCS_REMFAULT        (1 << 1)  /* Bit 1:  Remote fault occurred */
#define KS8721_INTCS_LINKDOWN        (1 << 2)  /* Bit 2:  Link down occurred */
#define KS8721_INTCS_LPACK           (1 << 3)  /* Bit 3:  Link partner acknowlege occurred */
#define KS8721_INTCS_PDFAULT         (1 << 4)  /* Bit 4:  Parallel detect fault occurred */
#define KS8721_INTCS_PGRCVD          (1 << 5)  /* Bit 5:  Page received occurred */
#define KS8721_INTCS_RXERR           (1 << 6)  /* Bit 6:  Receive error occurred */
#define KS8721_INTCS_JABBER          (1 << 7)  /* Bit 7:  Jabber interrupt occurred */
#define KS8721_INTCS_LINKUPE         (1 << 8)  /* Bit 8:  Enable link up interrupt */
#define KS8721_INTCS_REMFAULTE       (1 << 9)  /* Bit 9:  Enable remote fault interrupt */
#define KS8721_INTCS_LINKDOWNE       (1 << 10) /* Bit 10: Enable link down interrupt */
#define KS8721_INTCS_LPACKE          (1 << 11) /* Bit 11: Enable link partner acknowldgement interrupt */
#define KS8721_INTCS_PDFAULTE        (1 << 12) /* Bit 12: Enable parallel detect fault interrupt */
#define KS8721_INTCS_PGRCVDE         (1 << 13) /* Bit 13: Enable page received interrupt */
#define KS8721_INTCS_RXERRE          (1 << 14) /* Bit 14: Enable receive error interrupt */
#define KS8721_INTCS_JABBERE         (1 << 15) /* Bit 15: Enable Jabber Interrupt */

/* KS8921 10BASE-TX PHY control register */

#define KS8721_10BTCR_BIT0           (1 << 0)  /* Bit 0:  xxx */
#define KS8721_10BTCR_BIT1           (1 << 1)  /* Bit 1:  xxx */
#define KS8721_10BTCR_MODE_SHIFT     (2)       /* Bits 2-4:  Operation Mode Indication */
#define KS8721_10BTCR_MODE_MASK      (7 << KS8721_10BTCR_MODE_SHIFT)
#  define KS8721_10BTCR_MODE_ANEG    (0 << KS8721_10BTCR_MODE_SHIFT) /* Still in auto-negotiation */
#  define KS8721_10BTCR_MODE_10BTHD  (1 << KS8721_10BTCR_MODE_SHIFT) /* 10BASE-T half-duplex */
#  define KS8721_10BTCR_MODE_100BTHD (2 << KS8721_10BTCR_MODE_SHIFT) /* 100BASE_t half-duplex */
#  define KS8721_10BTCR_MODE_DEFAULT (3 << KS8721_10BTCR_MODE_SHIFT) /* Default */
#  define KS8721_10BTCR_MODE_10BTFD  (5 << KS8721_10BTCR_MODE_SHIFT) /* 10BASE-T full duplex */
#  define KS8721_10BTCR_MODE_100BTFD (6 << KS8721_10BTCR_MODE_SHIFT) /* 100BASE-T full duplex */
#  define KS8721_10BTCR_MODE_ISOLATE (7 << KS8721_10BTCR_MODE_SHIFT) /* PHY/MII isolate */
#define KS8721_10BTCR_ISOLATE        (1 << 5)  /* Bit 5:  PHY isolate */
#define KS8721_10BTCR_PAUSE          (1 << 6)  /* Bit 6:  Enable pause */
#define KS8721_10BTCR_ANEGCOMP       (1 << 7)  /* Bit 7:  Auto-negotiation complete */
#define KS8721_10BTCR_JABBERE        (1 << 8)  /* Bit 8:  Enable Jabber */
#define KS8721_10BTCR_INTLVL         (1 << 9)  /* Bit 9:  Interrupt level */
#define KS8721_10BTCR_POWER          (1 << 10) /* Bit 10: Power saving */
#define KS8721_10BTCR_FORCE          (1 << 11) /* Bit 11: Force link */
#define KS8721_10BTCR_ENERGY         (1 << 12) /* Bit 12: Energy detect */
#define KS8721_10BTCR_PAIRSWAPD      (1 << 13) /* Bit 13: Pairswap disable */

/****************************************************************************
 * Type Definitions
 ****************************************************************************/

/****************************************************************************
 * Public Function Prototypes
 ****************************************************************************/

#ifdef __cplusplus
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif

#undef EXTERN
#ifdef __cplusplus
}
#endif

#endif /* __INCLUDE_NUTTX_NET_MII_H */