/****************************************************************************
* arch/arm/src/kinetis/kinetis_pin.c
*
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <arch/board/board.h>
#include <assert.h>
#include <errno.h>
#include <nuttx/arch.h>
#include "up_arch.h"
#include "up_internal.h"
#include "kinetis_memorymap.h"
#include "kinetis_internal.h"
#include "kinetis_port.h"
#include "kinetis_gpio.h"
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/****************************************************************************
* Private Data
****************************************************************************/
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: kinetis_pinconfig
*
* Description:
* Configure a PIN based on bit-encoded description of the pin. NOTE that
* DMA/interrupts are disabled at the initial PIN configuratin.
*
****************************************************************************/
int kinetis_pinconfig(uint32_t cfgset)
{
uintptr_t base;
uint32_t regval;
unsigned int port;
unsigned int pin;
unsigned int mode;
/* Get the port number and pin number */
port = (cfgset & _PIN_PORT_MASK) >> _PIN_PORT_SHIFT;
pin = (cfgset & _PIN_MASK) >> _PIN_SHIFT;
DEBUGASSERT(port < KINETIS_NPORTS);
if (port < KINETIS_NPORTS)
{
/* Get the base address of PORT block for this port */
base = KINETIS_PORT_BASE(port);
/* Get the port mode */
mode = (cfgset & _PIN_MODE_MASK) >> _PIN_MODE_SHIFT;
/* Special case analog port mode. In this case, not of the digital
* options are applicable.
*/
if (mode == _PIN_MODE_ANALOG)
{
/* Set the analog mode with all digital options zeroed */
regval = PORT_PCR_MUX_ANALOG | PORT_PCR_IRQC_DISABLED;
putreg32(regval, base + KINETIS_PORT_PCR_OFFSET(pin));
}
else
{
/* Configure the digital pin options */
regval = (mode << PORT_PCR_MUX_SHIFT);
if ((cfgset & _PIN_IO_MASK) == _PIN_INPUT)
{
/* Handle input-only digital options */
/* Check for pull-up or pull-down */
if ((cfgset & _PIN_INPUT_PULLMASK) == _PIN_INPUT_PULLDOWN)
{
regval |= PORT_PCR_PE;
}
else if ((cfgset & _PIN_INPUT_PULLMASK) == _PIN_INPUT_PULLUP)
{
regval |= (PORT_PCR_PE | PORT_PCR_PS);
}
}
else
{
/* Handle output-only digital options */
/* Check for slow slew rate setting */
if ((cfgset & _PIN_OUTPUT_SLEW_MASK) == _PIN_OUTPUT_SLOW)
{
regval |= PORT_PCR_SRE;
}
/* Check for open drain output */
if ((cfgset & _PIN_OUTPUT_OD_MASK) == _PIN_OUTPUT_OPENDRAIN)
{
regval |= PORT_PCR_ODE;
}
/* Check for high drive output */
if ((cfgset & _PIN_OUTPUT_DRIVE_MASK) == _PIN_OUTPUT_HIGHDRIVE)
{
regval |= PORT_PCR_DSE;
}
}
/* Check for passive filter enable. Passive Filter configuration
* is valid in all digital pin muxing modes.
*/
if ((cfgset & PIN_PASV_FILTER) != 0)
{
regval |= PORT_PCR_PFE;
}
/* Set the digital mode with all of the selected options */
putreg32(regval, base + KINETIS_PORT_PCR_OFFSET(pin));
/* Check for digital filter enable. Digital Filter configuration
* is valid in all digital pin muxing modes.
*/
regval = getreg32(base + KINETIS_PORT_DFER_OFFSET);
if ((cfgset & PIN_DIG_FILTER) != 0)
{
regval |= (1 << pin);
}
else
{
regval &= ~(1 << pin);
}
putreg32(regval, base + KINETIS_PORT_DFER_OFFSET);
/* Additional configuration for the case of Alternative 1 (GPIO) modes */
if (mode == _PIN_MODE_GPIO)
{
/* Set the GPIO port direction */
base = KINETIS_GPIO_BASE(port);
regval = getreg32(base + KINETIS_GPIO_PDDR_OFFSET);
if ((cfgset & _PIN_IO_MASK) == _PIN_INPUT)
{
/* Select GPIO input */
regval &= ~(1 << pin);
putreg32(regval, base + KINETIS_GPIO_PDDR_OFFSET);
}
else /* if ((cfgset & _PIN_IO_MASK) == _PIN_OUTPUT) */
{
/* Select GPIO input */
regval |= (1 << pin);
putreg32(regval, base + KINETIS_GPIO_PDDR_OFFSET);
/* Set the initial value of the GPIO output */
kinetis_gpiowrite(cfgset, ((cfgset & GPIO_OUTPUT_ONE) != 0));
}
}
}
return OK;
}
return -EINVAL;
}
/************************************************************************************
* Name: kinetis_pinfilter
*
* Description:
* Configure the digital filter associated with a port. The digital filter
* capabilities of the PORT module are available in all digital pin muxing modes.
*
* Input parmeters:
* port - Port number. See KINETIS_PORTn definitions in kinetis_port.h
* lpo - true: Digital Filters are clocked by the bus clock
* false: Digital Filters are clocked by the 1 kHz LPO clock
* width - Filter Length
*
************************************************************************************/
int kinetis_pinfilter(unsigned int port, bool lpo, unsigned int width)
{
uintptr_t base;
uint32_t regval;
DEBUGASSERT(port < KINETIS_NPORTS);
if (port < KINETIS_NPORTS)
{
/* Get the base address of PORT block for this port */
base = KINETIS_PORT_BASE(port);
/* Select clocking */
regval = (lpo ? PORT_DFCR_CS : 0);
putreg32(regval, base + KINETIS_PORT_DFCR_OFFSET);
/* Select the filter width */
DEBUGASSERT(width < 32);
putreg32(width, base + KINETIS_PORT_DFWR_OFFSET);
return OK;
}
return -EINVAL;
}