/************************************************************************************
* arch/arm/src/lpc313x/lpc313x_internal.h
*
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __ARCH_ARM_SRC_LPC313X_LPC313X_INTERNAL_H
#define __ARCH_ARM_SRC_LPC313X_LPC313X_INTERNAL_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include "up_internal.h"
#include "chip.h"
/************************************************************************************
* Definitions
************************************************************************************/
/* Configuration ********************************************************************/
/* NVIC priority levels *************************************************************/
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Inline Functions
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Data
************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: lpc313x_clockconfig
*
* Description:
* Called to change to new clock based on settings in board.h
*
************************************************************************************/
EXTERN void lpc313x_clockconfig(void);
/************************************************************************************
* Name: lpc313x_configgpio
*
* Description:
* Configure a GPIO pin based on bit-encoded description of the pin.
*
************************************************************************************/
EXTERN int lpc313x_configgpio(uint32_t cfgset);
/************************************************************************************
* Name: lpc313x_gpiowrite
*
* Description:
* Write one or zero to the selected GPIO pin
*
************************************************************************************/
EXTERN void lpc313x_gpiowrite(uint32_t pinset, bool value);
/************************************************************************************
* Name: lpc313x_gpioread
*
* Description:
* Read one or zero from the selected GPIO pin
*
************************************************************************************/
EXTERN bool lpc313x_gpioread(uint32_t pinset);
/************************************************************************************
* Function: lpc313x_dumpgpio
*
* Description:
* Dump all GPIO registers associated with the provided base address
*
************************************************************************************/
#ifdef CONFIG_DEBUG
EXTERN int lpc313x_dumpgpio(uint32_t pinset, const char *msg);
#else
# define lpc313x_dumpgpio(p,m)
#endif
/************************************************************************************
* Name: lpc313x_spiselect and lpc313x_spistatus
*
* Description:
* The external functions, lpc313x_spiselect and lpc313x_spistatus must be
* provided by board-specific logic. They are implementations of the select
* and status methods of the SPI interface defined by struct spi_ops_s (see
* include/nuttx/spi.h). All other methods (including up_spiinitialize())
* are provided by common LPC313X logic. To use this common SPI logic on your
* board:
*
* 1. Provide logic in lpc313x_boardinitialize() to configure SPI chip select
* pins.
* 2. Provide lpc313x_spiselect() and lpc313x_spistatus() functions in your
* board-specific logic. These functions will perform chip selection and
* status operations using GPIOs in the way your board is configured.
* 3. Add a calls to up_spiinitialize() in your low level application
* initialization logic
* 4. The handle returned by up_spiinitialize() may then be used to bind the
* SPI driver to higher level logic (e.g., calling
* mmcsd_spislotinitialize(), for example, will bind the SPI driver to
* the SPI MMC/SD driver).
*
************************************************************************************/
struct spi_dev_s;
enum spi_dev_e;
EXTERN void lpc313x_spiselect(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected);
EXTERN uint8_t lpc313x_spistatus(FAR struct spi_dev_s *dev, enum spi_dev_e devid);
/************************************************************************************
* Name: lpc313x_usbpullup
*
* Description:
* If USB is supported and the board supports a pullup via GPIO (for USB software
* connect and disconnect), then the board software must provide lpc313x_pullup.
* See include/nuttx/usbdev.h for additional description of this method.
* Alternatively, if no pull-up GPIO the following EXTERN can be redefined to be
* NULL.
*
************************************************************************************/
struct usbdev_s;
EXTERN int lpc313x_usbpullup(FAR struct usbdev_s *dev, bool enable);
/************************************************************************************
* Name: lpc313x_usbsuspend
*
* Description:
* Board logic must provide the lpc313x_usbsuspend logic if the USBDEV driver is
* used. This function is called whenever the USB enters or leaves suspend mode.
* This is an opportunity for the board logic to shutdown clocks, power, etc.
* while the USB is suspended.
*
************************************************************************************/
struct usbdev_s;
EXTERN void lpc313x_usbsuspend(FAR struct usbdev_s *dev, bool resume);
/****************************************************************************
* Name: sdio_initialize
*
* Description:
* Initialize SDIO for operation.
*
* Input Parameters:
* slotno - Not used.
*
* Returned Values:
* A reference to an SDIO interface structure. NULL is returned on failures.
*
****************************************************************************/
struct sdio_dev_s; /* See include/nuttx/sdio.h */
EXTERN FAR struct sdio_dev_s *sdio_initialize(int slotno);
/****************************************************************************
* Name: sdio_mediachange
*
* Description:
* Called by board-specific logic -- posssible from an interrupt handler --
* in order to signal to the driver that a card has been inserted or
* removed from the slot
*
* Input Parameters:
* dev - An instance of the SDIO driver device state structure.
* cardinslot - true is a card has been detected in the slot; false if a
* card has been removed from the slot. Only transitions
* (inserted->removed or removed->inserted should be reported)
*
* Returned Values:
* None
*
****************************************************************************/
EXTERN void sdio_mediachange(FAR struct sdio_dev_s *dev, bool cardinslot);
/****************************************************************************
* Name: sdio_wrprotect
*
* Description:
* Called by board-specific logic to report if the card in the slot is
* mechanically write protected.
*
* Input Parameters:
* dev - An instance of the SDIO driver device state structure.
* wrprotect - true is a card is writeprotected.
*
* Returned Values:
* None
*
****************************************************************************/
EXTERN void sdio_wrprotect(FAR struct sdio_dev_s *dev, bool wrprotect);
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_ARM_SRC_LPC313X_LPC313X_INTERNAL_H */