############################################################################
# configs/lm3s6965-ek/nx/defconfig
#
# Copyright (C) 2010 Gregory Nutt. All rights reserved.
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions
# are met:
#
# 1. Redistributions of source code must retain the above copyright
# notice, this list of conditions and the following disclaimer.
# 2. Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in
# the documentation and/or other materials provided with the
# distribution.
# 3. Neither the name NuttX nor the names of its contributors may be
# used to endorse or promote products derived from this software
# without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# POSSIBILITY OF SUCH DAMAGE.
#
############################################################################
#
# architecture selection
#
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
# processor architecture.
# CONFIG_ARCH_family - for use in C code. This identifies the
# particular chip family that the architecture is implemented
# in.
# CONFIG_ARCH_architecture - for use in C code. This identifies the
# specific architecture within the chip familyl.
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
# CONFIG_ARCH_CHIP_name - For use in C code
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
# the board that supports the particular chip or SoC.
# CONFIG_ARCH_BOARD_name - for use in C code
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
# CONFIG_DRAM_START - The start address of DRAM (physical)
# CONFIG_DRAM_END - Last address+1 of installed RAM
# CONFIG_ARCH_IRQPRIO - The LM3S6965 supports interrupt prioritization
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
# stack. If defined, this symbol is the size of the interrupt
# stack in bytes. If not defined, the user task stacks will be
# used during interrupt handling.
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
# cause a 100 second delay during boot-up. This 100 second delay
# serves no purpose other than it allows you to calibratre
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
# the delay actually is 100 seconds.
#
CONFIG_ARCH=arm
CONFIG_ARCH_ARM=y
CONFIG_ARCH_CORTEXM3=y
CONFIG_ARCH_CHIP=lm3s
CONFIG_ARCH_CHIP_LM3S6965=y
CONFIG_ARCH_BOARD=lm3s6965-ek
CONFIG_ARCH_BOARD_LM3S6965EK=y
CONFIG_BOARD_LOOPSPERMSEC=4531
CONFIG_DRAM_SIZE=0x00010000
CONFIG_DRAM_START=0x20000000
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_INTERRUPTSTACK=n
CONFIG_ARCH_STACKDUMP=y
CONFIG_ARCH_LEDS=y
CONFIG_ARCH_CALIBRATION=n
#
# Identify toolchain and linker options
#
CONFIG_LM3S_CODESOURCERYW=n
CONFIG_LM3S_CODESOURCERYL=n
CONFIG_LM3S_DEVKITARM=n
CONFIG_LM3S_BUILDROOT=y
CONFIG_LM3S_DFU=y
#
# Disable support for interrupts on GPIOH and GPIOJ which do not
# exist on the LM3S6B96. Additional interrupt support can be
# disabled if desired to reduce memory footprint.
CONFIG_LM3S_DISABLE_GPIOA_IRQS=n
CONFIG_LM3S_DISABLE_GPIOB_IRQS=n
CONFIG_LM3S_DISABLE_GPIOC_IRQS=n
CONFIG_LM3S_DISABLE_GPIOD_IRQS=n
CONFIG_LM3S_DISABLE_GPIOE_IRQS=n
CONFIG_LM3S_DISABLE_GPIOF_IRQS=n
CONFIG_LM3S_DISABLE_GPIOG_IRQS=n
CONFIG_LM3S_DISABLE_GPIOH_IRQS=y
CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
#
# LM3S6965 specific serial device driver settings
#
# CONFIG_UARTn_DISABLE - select to disable all support for
# the UART
# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
# console and ttys0 (default is the UART0).
# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
# This specific the size of the receive buffer
# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
# being sent. This specific the size of the transmit buffer
# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
# CONFIG_UARTn_2STOP - Two stop bits
#
CONFIG_UART0_DISABLE=n
CONFIG_UART1_DISABLE=y
CONFIG_UART2_DISABLE=y
CONFIG_UART0_SERIAL_CONSOLE=y
CONFIG_UART1_SERIAL_CONSOLE=n
CONFIG_UART2_SERIAL_CONSOLE=n
CONFIG_UART0_TXBUFSIZE=256
CONFIG_UART1_TXBUFSIZE=256
CONFIG_UART2_TXBUFSIZE=256
CONFIG_UART0_RXBUFSIZE=256
CONFIG_UART1_RXBUFSIZE=256
CONFIG_UART2_RXBUFSIZE=256
CONFIG_UART0_BAUD=115200
CONFIG_UART1_BAUD=115200
CONFIG_UART2_BAUD=115200
CONFIG_UART0_BITS=8
CONFIG_UART1_BITS=8
CONFIG_UART2_BITS=8
CONFIG_UART0_PARITY=0
CONFIG_UART1_PARITY=0
CONFIG_UART2_PARITY=0
CONFIG_UART0_2STOP=0
CONFIG_UART1_2STOP=0
CONFIG_UART2_2STOP=0
#
# LM3S6965 specific SSI device driver settings
#
# CONFIG_SSIn_DISABLE - select to disable all support for
# the SSI
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
# Poll-waiting is recommended if the interrupt rate would be to
# high in the interrupt driven case.
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
# emptying the Rx FIFO. If the SPI frequency is high and this
# value is large, then larger values of this setting may cause
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
#
CONFIG_SSI0_DISABLE=n
CONFIG_SSI1_DISABLE=y
CONFIG_SSI_POLLWAIT=y
#CONFIG_SSI_TXLIMIT=4
#
# LM3S6965 specific serial device driver settings
#
# CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
# to build the LM3S Ethernet driver
# CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
# CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide
# a MAC address (via lm3s_ethernetmac()), then this should be selected.
# CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
# CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
# CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
# CONFIG_LM3S_MULTICAST - Set to enable multicast frames
# CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
# CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
# CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
#
CONFIG_LM3S_ETHERNET=n
CONFIG_LM3S_ETHLEDS=n
CONFIG_LM3S_BOARDMAC=y
CONFIG_LM3S_ETHHDUPLEX=n
CONFIG_LM3S_ETHNOAUTOCRC=n
CONFIG_LM3S_ETHNOPAD=n
CONFIG_LM3S_MULTICAST=n
CONFIG_LM3S_PROMISCUOUS=n
CONFIG_LM3S_BADCRC=n
CONFIG_LM3S_DUMPPACKET=n
#
# General build options
#
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
# used with many different loaders using the GNU objcopy program
# Should not be selected if you are not using the GNU toolchain.
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
# used with many different loaders using the GNU objcopy program
# Should not be selected if you are not using the GNU toolchain.
# CONFIG_RAW_BINARY - make a raw binary format file used with many
# different loaders using the GNU objcopy program. This option
# should not be selected if you are not using the GNU toolchain.
# CONFIG_HAVE_LIBM - toolchain supports libm.a
#
CONFIG_RRLOAD_BINARY=n
CONFIG_INTELHEX_BINARY=n
CONFIG_MOTOROLA_SREC=n
CONFIG_RAW_BINARY=y
CONFIG_HAVE_LIBM=n
#
# General SPI interface configuration
#
CONFIG_SPI_CMDDATA=y
#
# General OS setup
#
# CONFIG_APP_DIR - Identifies the relative path to the directory
# that builds the application to link with NuttX.
# CONFIG_DEBUG - enables built-in debug options
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
# debug symbols (needed for use with a debugger).
# CONFIG_MM_REGIONS - If the architecture includes multiple
# regions of memory to allocate from, this specifies the
# number of memory regions that the memory manager must
# handle and enables the API mm_addregion(start, end);
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
# time console output
# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz
# or TICKS_PER_MSEC=10. This setting may be defined to
# inform NuttX that the processor hardware is providing
# system timer interrupts at some interrupt interval other
# than 10 msec.
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
# this number of milliseconds; Round robin scheduling can
# be disabled by setting this value to zero.
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
# scheduler to monitor system performance
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
# task name to save in the TCB. Useful if scheduler
# instrumentation is selected. Set to zero to disable.
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
# Used to initialize the internal time logic.
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
# You would only need this if you are concerned about accurate
# time conversions in the past or in the distant future.
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
# would only need this if you are concerned about accurate
# time conversion in the distand past. You must also define
# CONFIG_GREGORIAN_TIME in order to use Julian time.
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
# provides /dev/console. Enables stdout, stderr, stdin.
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
# driver (minimul support)
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
# errorcheck mutexes. Enables pthread_mutexattr_settype().
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
# inheritance on mutexes and semaphores.
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
# inheritance is enabled. It defines the maximum number of
# different threads (minus one) that can take counts on a
# semaphore with priority inheritance support. This may be
# set to zero if priority inheritance is disabled OR if you
# are only using semaphores as mutexes (only one holder) OR
# if no more than two threads participate using a counting
# semaphore.
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
# then this setting is the maximum number of higher priority
# threads (minus 1) than can be waiting for another thread
# to release a count on a semaphore. This value may be set
# to zero if no more than one thread is expected to wait for
# a semaphore.
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
# by task_create() when a new task is started. If set, all
# files/drivers will appear to be closed in the new task.
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
# three file descriptors (stdin, stdout, stderr) by task_create()
# when a new task is started. If set, all files/drivers will
# appear to be closed in the new task except for stdin, stdout,
# and stderr.
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
# desciptors by task_create() when a new task is started. If
# set, all sockets will appear to be closed in the new task.
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
# This format will support execution of NuttX binaries located
# in a ROMFS filesystem (see examples/nxflat).
#
CONFIG_APP_DIR=examples/nx
CONFIG_DEBUG=n
CONFIG_DEBUG_VERBOSE=n
CONFIG_DEBUG_SYMBOLS=n
CONFIG_DEBUG_GRAPHICS=n
CONFIG_LCD_RITDEBUG=n
CONFIG_MM_REGIONS=1
CONFIG_ARCH_LOWPUTC=y
CONFIG_RR_INTERVAL=200
CONFIG_SCHED_INSTRUMENTATION=n
CONFIG_TASK_NAME_SIZE=0
CONFIG_START_YEAR=2010
CONFIG_START_MONTH=5
CONFIG_START_DAY=12
CONFIG_GREGORIAN_TIME=n
CONFIG_JULIAN_TIME=n
CONFIG_DEV_CONSOLE=y
CONFIG_DEV_LOWCONSOLE=n
CONFIG_MUTEX_TYPES=n
CONFIG_PRIORITY_INHERITANCE=n
CONFIG_SEM_PREALLOCHOLDERS=0
CONFIG_SEM_NNESTPRIO=0
CONFIG_FDCLONE_DISABLE=n
CONFIG_FDCLONE_STDIO=n
CONFIG_SDCLONE_DISABLE=y
CONFIG_NXFLAT=n
#
# The following can be used to disable categories of
# APIs supported by the OS. If the compiler supports
# weak functions, then it should not be necessary to
# disable functions unless you want to restrict usage
# of those APIs.
#
# There are certain dependency relationships in these
# features.
#
# o mq_notify logic depends on signals to awaken tasks
# waiting for queues to become full or empty.
# o pthread_condtimedwait() depends on signals to wake
# up waiting tasks.
#
CONFIG_DISABLE_CLOCK=n
CONFIG_DISABLE_POSIX_TIMERS=y
CONFIG_DISABLE_PTHREAD=n
CONFIG_DISABLE_SIGNALS=n
CONFIG_DISABLE_MQUEUE=n
CONFIG_DISABLE_MOUNTPOINT=y
CONFIG_DISABLE_ENVIRON=y
CONFIG_DISABLE_POLL=y
#
# Misc libc settings
#
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
# little smaller if we do not support fieldwidthes
#
CONFIG_NOPRINTF_FIELDWIDTH=n
#
# Allow for architecture optimized implementations
#
# The architecture can provide optimized versions of the
# following to improve system performance
#
CONFIG_ARCH_MEMCPY=n
CONFIG_ARCH_MEMCMP=n
CONFIG_ARCH_MEMMOVE=n
CONFIG_ARCH_MEMSET=n
CONFIG_ARCH_STRCMP=n
CONFIG_ARCH_STRCPY=n
CONFIG_ARCH_STRNCPY=n
CONFIG_ARCH_STRLEN=n
CONFIG_ARCH_STRNLEN=n
CONFIG_ARCH_BZERO=n
CONFIG_ARCH_KMALLOC=n
CONFIG_ARCH_KZMALLOC=n
CONFIG_ARCH_KFREE=n
#
# Sizes of configurable things (0 disables)
#
# CONFIG_MAX_TASKS - The maximum number of simultaneously
# active tasks. This value must be a power of two.
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
# of parameters that a task may receive (i.e., maxmum value
# of 'argc')
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
# specific data that can be retained
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
# descriptors (one for each open)
# CONFIG_NFILE_STREAMS - The maximum number of streams that
# can be fopen'ed
# CONFIG_NAME_MAX - The maximum size of a file name.
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
# CONFIG_NUNGET_CHARS - Number of characters that can be
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
# structures. The system manages a pool of preallocated
# message structures to minimize dynamic allocations
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
# a fixed payload size given by this settin (does not include
# other message structure overhead.
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
# can be passed to a watchdog handler
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
# structures. The system manages a pool of preallocated
# watchdog structures to minimize dynamic allocations
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
# timer structures. The system manages a pool of preallocated
# timer structures to minimize dynamic allocations. Set to
# zero for all dynamic allocations.
#
CONFIG_MAX_TASKS=16
CONFIG_MAX_TASK_ARGS=4
CONFIG_NPTHREAD_KEYS=4
CONFIG_NFILE_DESCRIPTORS=12
CONFIG_NFILE_STREAMS=12
CONFIG_NAME_MAX=32
CONFIG_STDIO_BUFFER_SIZE=256
CONFIG_NUNGET_CHARS=2
CONFIG_PREALLOC_MQ_MSGS=4
CONFIG_MQ_MAXMSGSIZE=32
CONFIG_MAX_WDOGPARMS=2
CONFIG_PREALLOC_WDOGS=4
CONFIG_PREALLOC_TIMERS=4
#
# Framebuffer driver options
CONFIG_FB_CMAP=n
CONFIG_FB_HWCURSOR=n
CONFIG_FB_HWCURSORIMAGE=n
#CONFIG_FB_HWCURSORSIZE
#CONFIG_FB_TRANSPARENCY
#
# Filesystem configuration
#
# CONFIG_FS_FAT - Enable FAT filesystem support
# CONFIG_FAT_SECTORSIZE - Max supported sector size
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
CONFIG_FS_FAT=n
CONFIG_FS_ROMFS=n
#
# SPI-based MMC/SD driver
#
# CONFIG_MMCSD_NSLOTS
# Number of MMC/SD slots supported by the driver
# CONFIG_MMCSD_READONLY
# Provide read-only access (default is read/write)
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
# Default is 20MHz.
#
CONFIG_MMCSD_NSLOTS=1
CONFIG_MMCSD_READONLY=n
CONFIG_MMCSD_SPICLOCK=12500000
#
# TCP/IP and UDP support via uIP
# CONFIG_NET - Enable or disable all network features
# CONFIG_NET_IPv6 - Build in support for IPv6
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
# CONFIG_NET_BUFSIZE - uIP buffer size
# CONFIG_NET_TCP - TCP support on or off
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
# accept() is called. The size of the backlog is selected when listen() is called.
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
# CONFIG_NET_UDP - UDP support on or off
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
# CONFIG_NET_ICMP - ICMP ping response support on or off
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
# CONFIG_NET_STATISTICS - uIP statistics on or off
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
# CONFIG_NET_BROADCAST - Broadcast support
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
#
CONFIG_NET=n
CONFIG_NET_IPv6=n
CONFIG_NSOCKET_DESCRIPTORS=0
CONFIG_NET_SOCKOPTS=y
CONFIG_NET_BUFSIZE=420
CONFIG_NET_TCP=n
CONFIG_NET_TCP_CONNS=40
CONFIG_NET_MAX_LISTENPORTS=40
CONFIG_NET_UDP=n
CONFIG_NET_UDP_CHECKSUMS=y
#CONFIG_NET_UDP_CONNS=10
CONFIG_NET_ICMP=n
CONFIG_NET_ICMP_PING=n
#CONFIG_NET_PINGADDRCONF=0
CONFIG_NET_STATISTICS=y
#CONFIG_NET_RECEIVE_WINDOW=
#CONFIG_NET_ARPTAB_SIZE=8
CONFIG_NET_BROADCAST=n
#CONFIG_NET_FWCACHE_SIZE=2
#
# UIP Network Utilities
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
#
CONFIG_NET_DHCP_LIGHT=n
CONFIG_NET_RESOLV_ENTRIES=4
#
# Graphics related configuration settings
#
# CONFIG_NX
# Enables overall support for graphics library and NX
# CONFIG_NX_MULTIUSER
# Configures NX in multi-user mode
# CONFIG_NX_NPLANES
# Some YUV color formats requires support for multiple planes,
# one for each color component. Unless you have such special
# hardware, this value should be undefined or set to 1
# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
# CONFIG_NX_DISABLE_32BPP
# NX supports a variety of pixel depths. You can save some
# memory by disabling support for unused color depths.
# CONFIG_NX_PACKEDMSFIRST
# If a pixel depth of less than 8-bits is used, then NX needs
# to know if the pixels pack from the MS to LS or from LS to MS
# CONFIG_NX_LCDDRIVER
# By default, NX builds to use a framebuffer driver (see
# include/nuttx/fb.h). If this option is defined, NX will
# build to use an LCD driver (see include/nuttx/lcd/lcd.h).
# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
# CONFIG_NX_MOUSE
# Build in support for mouse input
# CONFIG_NX_KBD
# Build in support of keypad/keyboard input
# CONFIG_NXTK_BORDERWIDTH
# Specifies with with of the border (in pixels) used with
# framed windows. The default is 4.
# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
# Specify the colors of the border used with framed windows.
# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
# is normally darker. The default is medium and dark grey,
# respectively
# CONFIG_NXTK_AUTORAISE
# If set, a window will be raised to the top if the mouse position
# is over a visible portion of the window. Default: A mouse
# button must be clicked over a visible portion of the window.
# CONFIG_NXFONTS_CHARBITS
# The number of bits in the character set. Current options are
# only 7 and 8. The default is 7.
# CONFIG_NXFONT_SANS
# At present, there is only one font. But if there were were more,
# then this option would select the sans serif font.
#
# NX Multi-user only options:
#
# CONFIG_NX_BLOCKING
# Open the client message queues in blocking mode. In this case,
# nx_eventhandler() will not return until a message is received and processed.
# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
# Specifies the maximum number of messages that can fit in
# the message queues. No additional resources are allocated, but
# this can be set to prevent flooding of the client or server with
# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
# messages are pre-allocated).
#
CONFIG_NX=y
CONFIG_NX_MULTIUSER=n
CONFIG_NX_NPLANES=1
CONFIG_NX_DISABLE_1BPP=y
CONFIG_NX_DISABLE_2BPP=y
CONFIG_NX_DISABLE_4BPP=n
CONFIG_NX_DISABLE_8BPP=y
CONFIG_NX_DISABLE_16BPP=y
CONFIG_NX_DISABLE_24BPP=y
CONFIG_NX_DISABLE_32BPP=y
CONFIG_NX_PACKEDMSFIRST=y
CONFIG_NX_LCDDRIVER=y
CONFIG_LCD_MAXPOWER=1
CONFIG_LCD_MAXCONTRAST=255
CONFIG_NX_MOUSE=y
CONFIG_NX_KBD=y
#CONFIG_NXTK_BORDERWIDTH=4
CONFIG_NXTK_BORDERCOLOR1=8
CONFIG_NXTK_BORDERCOLOR2=4
CONFIG_NXTK_AUTORAISE=n
CONFIG_NXFONT_SANS=y
CONFIG_NXFONTS_CHARBITS=7
CONFIG_NX_BLOCKING=y
CONFIG_NX_MXSERVERMSGS=32
CONFIG_NX_MXCLIENTMSGS=16
#
# RiT P14201 OLED Driver Configuration
#
# CONFIG_LCD_P14201 - Enable P14201 support
# CONFIG_P14201_SPIMODE - Controls the SPI mode (should be mode 2)
# CONFIG_P14201_FREQUENCY - Define to use a different bus frequency
# CONFIG_P14201_NINTERFACES - Specifies the number of physical P14201 devices that
# will be supported.
# CONFIG_P14201_FRAMEBUFFER - If defined, accesses will be performed using an in-memory
# copy of the OLEDs GDDRAM. This cost of this buffer is 128 * 96 / 2 = 6Kb. If this
# is defined, then the driver will be fully functional. If not, then it will have the
# following limitations:
# - Reading graphics memory cannot be supported, and
# - All pixel writes must be aligned to byte boundaries.
#
# The latter limitation effectively reduces the 128x96 disply to 64x96.
CONFIG_LCD_P14201=y
CONFIG_P14201_SPIMODE=2
CONFIG_P14201_FREQUENCY=3500000
CONFIG_P14201_NINTERFACES=1
CONFIG_P14201_FRAMEBUFFER=y
#
# Settings for examples/uip
#
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
CONFIG_EXAMPLE_UIP_DHCPC=n
#
# Settings for examples/nettest
CONFIG_EXAMPLE_NETTEST_SERVER=n
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
CONFIG_EXAMPLE_NETTEST_NOMAC=n
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
#
# Settings for examples/ostest
#
CONFIG_EXAMPLES_OSTEST_LOOPS=1
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
#
# Settings for examples/nsh
#
# CONFIG_EXAMPLES_NSH_FILEIOSIZE - Size of a static I/O buffer
# CONFIG_EXAMPLES_NSH_STRERROR - Use strerror(errno)
# CONFIG_EXAMPLES_NSH_LINELEN - Maximum length of one command line
# CONFIG_EXAMPLES_NSH_STACKSIZE - Stack size to use for new threads.
# CONFIG_EXAMPLES_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
# CONFIG_EXAMPLES_NSH_DISABLESCRIPT - Disable scripting support
# CONFIG_EXAMPLES_NSH_DISABLEBG - Disable background commands
# CONFIG_EXAMPLES_NSH_ROMFSETC - Use startup script in /etc
# CONFIG_EXAMPLES_NSH_CONSOLE - Use serial console front end
# CONFIG_EXAMPLES_NSH_TELNET - Use telnetd console front end
# CONFIG_EXAMPLES_NSH_ARCHINIT - Platform provides architecture
# specific initialization (nsh_archinitialize()).
#
# If CONFIG_EXAMPLES_NSH_TELNET is selected:
# CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
# CONFIG_EXAMPLES_NSH_DHCPC - Obtain address using DHCP
# CONFIG_EXAMPLES_NSH_IPADDR - Provides static IP address
# CONFIG_EXAMPLES_NSH_DRIPADDR - Provides static router IP address
# CONFIG_EXAMPLES_NSH_NETMASK - Provides static network mask
# CONFIG_EXAMPLES_NSH_NOMAC - Use a bogus MAC address
#
# If CONFIG_EXAMPLES_NSH_ROMFSETC is selected:
# CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT - ROMFS mountpoint
# CONFIG_EXAMPLES_NSH_INITSCRIPT - Relative path to init script
# CONFIG_EXAMPLES_NSH_ROMFSDEVNO - ROMFS RAM device minor
# CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE - ROMF sector size
# CONFIG_EXAMPLES_NSH_FATDEVNO - FAT FS RAM device minor
# CONFIG_EXAMPLES_NSH_FATSECTSIZE - FAT FS sector size
# CONFIG_EXAMPLES_NSH_FATNSECTORS - FAT FS number of sectors
# CONFIG_EXAMPLES_NSH_FATMOUNTPT - FAT FS mountpoint
#
CONFIG_EXAMPLES_NSH_FILEIOSIZE=512
CONFIG_EXAMPLES_NSH_STRERROR=n
CONFIG_EXAMPLES_NSH_LINELEN=64
CONFIG_EXAMPLES_NSH_STACKSIZE=2048
CONFIG_EXAMPLES_NSH_NESTDEPTH=3
CONFIG_EXAMPLES_NSH_DISABLESCRIPT=n
CONFIG_EXAMPLES_NSH_DISABLEBG=n
CONFIG_EXAMPLES_NSH_ROMFSETC=n
CONFIG_EXAMPLES_NSH_CONSOLE=y
CONFIG_EXAMPLES_NSH_TELNET=n
CONFIG_EXAMPLES_NSH_ARCHINIT=n
CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE=512
CONFIG_EXAMPLES_NSH_DHCPC=n
CONFIG_EXAMPLES_NSH_NOMAC=n
CONFIG_EXAMPLES_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
CONFIG_EXAMPLES_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
CONFIG_EXAMPLES_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT="/etc"
CONFIG_EXAMPLES_NSH_INITSCRIPT="init.d/rcS"
CONFIG_EXAMPLES_NSH_ROMFSDEVNO=0
CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE=64
CONFIG_EXAMPLES_NSH_FATDEVNO=1
CONFIG_EXAMPLES_NSH_FATSECTSIZE=512
CONFIG_EXAMPLES_NSH_FATNSECTORS=1024
CONFIG_EXAMPLES_NSH_FATMOUNTPT=/tmp
#
# Architecture-specific NSH options
#
CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO=0
CONFIG_EXAMPLES_NSH_MMCSDSLOTNO=0
CONFIG_EXAMPLES_NSH_MMCSDMINOR=0
#
# Settings for examples/nx
#
# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame-
# buffer driver for use in the test. Default: 0
# CONFIG_EXAMPLES_NX_DEVNO - The LCD device to select from the LCD
# driver for use in the test: Default: 0
# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background. Default depends on
# CONFIG_EXAMPLES_NX_BPP.
# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on
# CONFIG_EXAMPLES_NX_BPP.
# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on
# CONFIG_EXAMPLES_NX_BPP.
# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on
# CONFIG_EXAMPLES_NX_BPP.
# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on
# CONFIG_EXAMPLES_NX_BPP.
# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use. Valid options
# include 2, 4, 8, 16, 24, and 32. Default is 32.
# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows; Default is to
# use pretty, framed NXTK windows with toolbars.
# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating
# the NX server. Default 2048
# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority. Default: 80
# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority. Default: 120
# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with
# nx_eventnotify(). Default: 4
CONFIG_EXAMPLES_NX_VPLANE=0
CONFIG_EXAMPLES_NX_DEVNO=0
CONFIG_EXAMPLES_NX_BGCOLOR=2
CONFIG_EXAMPLES_NX_COLOR1=10
CONFIG_EXAMPLES_NX_COLOR2=12
CONFIG_EXAMPLES_NX_TBCOLOR=8
CONFIG_EXAMPLES_NX_FONTCOLOR=0
CONFIG_EXAMPLES_NX_BPP=4
CONFIG_EXAMPLES_NX_RAWWINDOWS=n
CONFIG_EXAMPLES_NX_STACKSIZE=2048
CONFIG_EXAMPLES_NX_CLIENTPRIO=80
CONFIG_EXAMPLES_NX_SERVERPRIO=120
CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
CONFIG_EXAMPLES_NX_EXTERNINIT=y
#
# Stack and heap information
#
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
# operation from FLASH but must copy initialized .data sections to RAM.
# (should also be =n for the LM3S6965 Eval Kit which always runs from flash)
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
# but copy themselves entirely into RAM for better performance.
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
# all stack operations outside of the nuttx model.
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
# This is the thread that (1) performs the inital boot of the system up
# to the point where user_start() is spawned, and (2) there after is the
# IDLE thread that executes only when there is no other thread ready to
# run.
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
# for the main user thread that begins at the user_start() entry point.
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
# CONFIG_HEAP_BASE - The beginning of the heap
# CONFIG_HEAP_SIZE - The size of the heap
#
CONFIG_BOOT_RUNFROMFLASH=n
CONFIG_BOOT_COPYTORAM=n
CONFIG_CUSTOM_STACK=n
CONFIG_STACK_POINTER=
CONFIG_IDLETHREAD_STACKSIZE=1024
CONFIG_USERMAIN_STACKSIZE=2048
CONFIG_PTHREAD_STACK_MIN=256
CONFIG_PTHREAD_STACK_DEFAULT=2048
CONFIG_HEAP_BASE=
CONFIG_HEAP_SIZE=
