/************************************************************************************
* configs/sam3u-ek/src/up_touchscreen.c
* arch/arm/src/board/up_touchscreen.c
*
* Copyright (C) 2011 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdbool.h>
#include <stdio.h>
#include <debug.h>
#include <errno.h>
#include <nuttx/spi.h>
#include <nuttx/input/touchscreen.h>
#include <nuttx/input/ads7843e.h>
#include "sam3u_internal.h"
#include "sam3uek_internal.h"
/****************************************************************************
* Pre-Processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
#ifdef CONFIG_INPUT_ADS7843E
#ifndef CONFIG_INPUT
# error "Touchscreen support requires CONFIG_INPUT"
#endif
#ifndef CONFIG_SAM3U_SPI
# error "Touchscreen support requires CONFIG_SAM3U_SPI"
#endif
#ifndef CONFIG_GPIOA_IRQ
# error "Touchscreen support requires CONFIG_GPIOA_IRQ"
#endif
#ifndef CONFIG_ADS7843E_FREQUENCY
# define CONFIG_ADS7843E_FREQUENCY 500000
#endif
#ifndef CONFIG_ADS7843E_SPIDEV
# define CONFIG_ADS7843E_SPIDEV 0
#endif
#if CONFIG_ADS7843E_SPIDEV != 0
# error "CONFIG_ADS7843E_SPIDEV must be zero"
#endif
#ifndef CONFIG_ADS7843E_DEVMINOR
# define CONFIG_ADS7843E_DEVMINOR 0
#endif
/****************************************************************************
* Static Function Prototypes
****************************************************************************/
/* IRQ/GPIO access callbacks. These operations all hidden behind
* callbacks to isolate the ADS7843E driver from differences in GPIO
* interrupt handling by varying boards and MCUs. If possible,
* interrupts should be configured on both rising and falling edges
* so that contact and loss-of-contact events can be detected.
*
* attach - Attach the ADS7843E interrupt handler to the GPIO interrupt
* enable - Enable or disable the GPIO interrupt
* clear - Acknowledge/clear any pending GPIO interrupt
* pendown - Return the state of the pen down GPIO input
*/
static int tsc_attach(FAR struct ads7843e_config_s *state, xcpt_t isr);
static void tsc_enable(FAR struct ads7843e_config_s *state, bool enable);
static void tsc_clear(FAR struct ads7843e_config_s *state);
static bool tsc_busy(FAR struct ads7843e_config_s *state);
static bool tsc_pendown(FAR struct ads7843e_config_s *state);
/****************************************************************************
* Private Data
****************************************************************************/
/* A reference to a structure of this type must be passed to the ADS7843E
* driver. This structure provides information about the configuration
* of the ADS7843E and provides some board-specific hooks.
*
* Memory for this structure is provided by the caller. It is not copied
* by the driver and is presumed to persist while the driver is active. The
* memory must be writable because, under certain circumstances, the driver
* may modify frequency or X plate resistance values.
*/
static struct ads7843e_config_s g_tscinfo =
{
.frequency = CONFIG_ADS7843E_FREQUENCY,
.attach = tsc_attach,
.enable = tsc_enable,
.clear = tsc_clear,
.busy = tsc_busy,
.pendown = tsc_pendown,
};
/****************************************************************************
* Private Functions
****************************************************************************/
/* IRQ/GPIO access callbacks. These operations all hidden behind
* callbacks to isolate the ADS7843E driver from differences in GPIO
* interrupt handling by varying boards and MCUs. If possible,
* interrupts should be configured on both rising and falling edges
* so that contact and loss-of-contact events can be detected.
*
* attach - Attach the ADS7843E interrupt handler to the GPIO interrupt
* enable - Enable or disable the GPIO interrupt
* clear - Acknowledge/clear any pending GPIO interrupt
* pendown - Return the state of the pen down GPIO input
*/
static int tsc_attach(FAR struct ads7843e_config_s *state, xcpt_t isr)
{
/* Attach the ADS7843E interrupt */
ivdbg("Attaching %p to IRQ %d\n", isr, SAM3U_TCS_IRQ);
return irq_attach(SAM3U_TCS_IRQ, isr);
}
static void tsc_enable(FAR struct ads7843e_config_s *state, bool enable)
{
/* Attach and enable, or detach and disable */
ivdbg("IRQ:%d enable:%d\n", SAM3U_TCS_IRQ, enable);
if (enable)
{
sam3u_gpioirqenable(SAM3U_TCS_IRQ);
}
else
{
sam3u_gpioirqdisable(SAM3U_TCS_IRQ);
}
}
static void tsc_clear(FAR struct ads7843e_config_s *state)
{
/* Does nothing */
}
static bool tsc_busy(FAR struct ads7843e_config_s *state)
{
/* REVISIT: This might need to be inverted */
bool busy = sam3u_gpioread(GPIO_TCS_BUSY);
ivdbg("busy:%d\n", busy);
return busy;
}
static bool tsc_pendown(FAR struct ads7843e_config_s *state)
{
/* REVISIT: This might need to be inverted */
bool pendown = sam3u_gpioread(GPIO_TCS_IRQ);
ivdbg("pendown:%d\n", pendown);
return pendown;
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: arch_tcinitialize
*
* Description:
* Initialize the touchscreen device
*
****************************************************************************/
int arch_tcinitialize(void)
{
FAR struct spi_dev_s *dev;
int ret;
ivdbg("Initializing\n");
/* Configure and enable the ADS7843E interrupt pin as an input */
(void)sam3u_configgpio(GPIO_TCS_BUSY);
(void)sam3u_configgpio(GPIO_TCS_IRQ);
/* Configure the PIO interrupt */
sam3u_gpioirq(GPIO_TCS_IRQ);
/* Get an instance of the SPI interface */
dev = up_spiinitialize(CONFIG_ADS7843E_SPIDEV);
if (!dev)
{
idbg("Failed to initialize SPI bus %d\n", CONFIG_ADS7843E_SPIDEV);
return -ENODEV;
}
/* Initialize and register the SPI touschscreen device */
ret = ads7843e_register(dev, &g_tscinfo, CONFIG_ADS7843E_DEVMINOR);
if (ret < 0)
{
idbg("Failed to initialize SPI bus %d\n", CONFIG_ADS7843E_SPIDEV);
/* up_spiuninitialize(dev); */
return -ENODEV;
}
return OK;
}
/****************************************************************************
* Name: arch_tcuninitialize
*
* Description:
* Un-initialize the touchscreen device
*
****************************************************************************/
void arch_tcuninitialize(void)
{
/* No support for un-initializing the touchscreen ADS7843E device yet */
}
#endif /* CONFIG_INPUT_ADS7843E */