/************************************************************************************
* configs/sam4s-xplained-pro/src/sam4s-xplained-pro.h
*
* Copyright (C) 2014 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_SAM4S_XPLAINED_SRC_SAM4S_XPLAINED_H
#define __CONFIGS_SAM4S_XPLAINED_SRC_SAM4S_XPLAINED_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
#include <arch/irq.h>
#include <nuttx/irq.h>
#include "chip/sam_pinmap.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Configuration ********************************************************************/
#define HAVE_HSMCI 1
#define HAVE_PROC 1
/* HSMCI */
/* Can't support MMC/SD if the card interface is not enabled */
#if !defined(CONFIG_SAM34_HSMCI)
# undef HAVE_HSMCI
#endif
#if !defined(CONFIG_FS_PROCFS)
# undef HAVE_PROC
#endif
/* Can't support MMC/SD features if mountpoints are disabled */
if defined(HAVE_HSMCI) && defined(CONFIG_DISABLE_MOUNTPOINT)
# warning Mountpoints disabled. No MMC/SD support
# undef HAVE_HSMCI
#endif
#if defined(HAVE_PROC) && defined(CONFIG_DISABLE_MOUNTPOINT)
# warning Mountpoints disabled. No procfs support
# undef HAVE_PROC
#endif
/* We need PIO interrupts on PIOC to support card detect interrupts */
#if defined(HAVE_HSMCI) && !defined(CONFIG_GPIOC_IRQ)
# warning PIOC interrupts not enabled. No MMC/SD support.
# undef HAVE_HSMCI
#endif
/* There are four LEDs on board the SAM4S Xplained board, two of these can be
* controlled by software in the SAM4S:
*
* LED GPIO
* ---------------- -----
* D9 Yellow LED PC10
* D10 Yellow LED PC17
*
* Both can be illuminated by driving the GPIO output to ground (low).
*
* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
* defined. In that case, the usage by the board port is defined in
* include/board.h and src/up_leds.c. The LEDs are used to encode OS-related
* events as follows:
*
* SYMBOL Meaning LED state
* D9 D10
* ------------------- ----------------------- -------- --------
* LED_STARTED NuttX has been started OFF OFF
* LED_HEAPALLOCATE Heap has been allocated OFF OFF
* LED_IRQSENABLED Interrupts enabled OFF OFF
* LED_STACKCREATED Idle stack created ON OFF
* LED_INIRQ In an interrupt No change
* LED_SIGNAL In a signal handler No change
* LED_ASSERTION An assertion failed No change
* LED_PANIC The system has crashed OFF Blinking
* LED_IDLE MCU is is sleep mode Not used
*
* Thus if D9 is statically on, NuttX has successfully booted and is,
* apparently, running normally. If D10 is flashing at approximately
* 2Hz, then a fatal error has been detected and the system has halted.
*/
#define GPIO_D301 (GPIO_OUTPUT | GPIO_CFG_PULLUP | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOC | GPIO_PIN23)
/* Mechanical buttons:
*
* The SAM4S Xplained Pro has two mechanical buttons. One button is the RESET button
* connected to the SAM4S reset line and the other is a generic user configurable
* button labeled SW0. When a button is pressed it will drive the I/O line to GND.
*
* PA2 SW0
*/
#define GPIO_SW0 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \
GPIO_INT_BOTHEDGES | GPIO_PORT_PIOA | GPIO_PIN2)
#define IRQ_SW0 SAM_IRQ_PA2
/* HSMCI SD Card Detect PC12 */
#define GPIO_MCI_CD (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_PORT_PIOC | GPIO_PIN12)
#define MCI_CD_IRQ SAM_IRQ_PC12
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Public data
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Functions
************************************************************************************/
/************************************************************************************
* Name: board_led_initialize
************************************************************************************/
#ifdef CONFIG_ARCH_LEDS
void board_led_initialize(void);
#endif
/************************************************************************************
* Name: sam_hsmci_initialize
*
* Description:
* Initialize HSMCI support
*
************************************************************************************/
#ifdef HAVE_HSMCI
int sam_hsmci_initialize(void);
#else
# define sam_hsmci_initialize()
#endif
/************************************************************************************
* Name: sam_cardinserted
*
* Description:
* Check if a card is inserted into the selected HSMCI slot
*
************************************************************************************/
#ifdef HAVE_HSMCI
bool sam_cardinserted(int slotno);
#else
# define sam_cardinserted(slotno) (false)
#endif
/************************************************************************************
* Name: sam_writeprotected
*
* Description:
* Check if the card in the MMCSD slot is write protected
*
************************************************************************************/
#ifdef HAVE_HSMCI
bool sam_writeprotected(int slotno);
#else
# define sam_writeprotected(slotno) (false)
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_SAM4S_XPLAINED_SRC_SAM4S_XPLAINED_H */