/************************************************************************************
* configs/sam3uek_eval/src/sam4s-xplained.h
*
* Copyright (C) 2009-2011, 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_SAM4S_XPLAINED_SRC_SAM4S_XPLAINED_H
#define __CONFIGS_SAM4S_XPLAINED_SRC_SAM4S_XPLAINED_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
#include <arch/irq.h>
#include <nuttx/irq.h>
#include "chip/sam_pinmap.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* There are four LEDs on board the SAM4S Xplained board, two of these can be
* controlled by software in the SAM4S:
*
* LED GPIO
* ---------------- -----
* D9 Yellow LED PC10
* D10 Yellow LED PC17
*
* Both can be illuminated by driving the GPIO output to ground (low).
*
* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
* defined. In that case, the usage by the board port is defined in
* include/board.h and src/up_leds.c. The LEDs are used to encode OS-related
* events as follows:
*
* SYMBOL Meaning LED state
* D9 D10
* ------------------- ----------------------- -------- --------
* LED_STARTED NuttX has been started OFF OFF
* LED_HEAPALLOCATE Heap has been allocated OFF OFF
* LED_IRQSENABLED Interrupts enabled OFF OFF
* LED_STACKCREATED Idle stack created ON OFF
* LED_INIRQ In an interrupt No change
* LED_SIGNAL In a signal handler No change
* LED_ASSERTION An assertion failed No change
* LED_PANIC The system has crashed OFF Blinking
* LED_IDLE MCU is is sleep mode Not used
*
* Thus if D9 is statically on, NuttX has successfully booted and is,
* apparently, running normmally. If D10 is flashing at approximately
* 2Hz, then a fatal error has been detected and the system has halted.
*/
#define GPIO_D9 (GPIO_OUTPUT | GPIO_CFG_PULLUP | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOC | GPIO_PIN10)
#define GPIO_D10 (GPIO_OUTPUT | GPIO_CFG_PULLUP | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOC | GPIO_PIN17)
/* Mechanical buttons:
*
* The SAM4S Xplained has two mechanical buttons. One button is the RESET button
* connected to the SAM4S reset line and the other is a generic user configurable
* button labeled BP2. When a button is pressed it will drive the I/O line to GND.
*
* PA5 BP2
*/
#define GPIO_BP2 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \
GPIO_PORT_PIOA | GPIO_PIN5)
#define IRQ_BP2 SAM_IRQ_PA5
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Public data
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Functions
************************************************************************************/
/****************************************************************************
* Name: up_ledinit
****************************************************************************/
#ifdef CONFIG_ARCH_LEDS
void up_ledinit(void);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_SAM4S_XPLAINED_SRC_SAM4S_XPLAINED_H */
