path: root/nuttx/configs/sama5d3x-ek/src/sam_usb.c

/************************************************************************************
 * configs/sama5d3x-ek/src/sam_usb.c
 *
 *   Copyright (C) 2013 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************/

/************************************************************************************
 * Included Files
 ************************************************************************************/

#include <nuttx/config.h>

#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include <sched.h>
#include <errno.h>
#include <assert.h>
#include <debug.h>

#include <nuttx/usb/usbdev.h>
#include <nuttx/usb/usbhost.h>
#include <nuttx/usb/usbdev_trace.h>

#include "up_arch.h"
#include "sam_pio.h"
#include "sam_usbhost.h"
#include "chip/sam_ohci.h"
#include "sama5d3x-ek.h"

#if defined(CONFIG_SAMA5_UHPHS) || defined(CONFIG_SAMA5_UDPHS)

/************************************************************************************
 * Pre-processor Definitions
 ************************************************************************************/

#ifndef CONFIG_USBHOST_DEFPRIO
#  define CONFIG_USBHOST_DEFPRIO 50
#endif

#ifndef CONFIG_USBHOST_STACKSIZE
#  define CONFIG_USBHOST_STACKSIZE 1024
#endif

#ifdef HAVE_USBDEV
#  undef CONFIG_SAMA5_UHPHS_RHPORT1
#endif

/************************************************************************************
 * Private Data
 ************************************************************************************/
/* Retained device driver handles */

#ifdef CONFIG_SAMA5_OHCI
static struct usbhost_connection_s *g_ohciconn;
#endif
#ifdef CONFIG_SAMA5_EHCI
static struct usbhost_connection_s *g_ehciconn;
#endif

/* Overcurrent interrupt handler */

#if defined(HAVE_USBHOST) && defined(CONFIG_SAMA5_PIOD_IRQ)
static xcpt_t g_ochandler;
#endif

/************************************************************************************
 * Private Functions
 ************************************************************************************/

/************************************************************************************
 * Name: usbhost_waiter
 *
 * Description:
 *   Wait for USB devices to be connected to either the OHCI or EHCI hub.
 *
 ************************************************************************************/

#if HAVE_USBHOST
#ifdef CONFIG_DEBUG_USB
static int usbhost_waiter(struct usbhost_connection_s *dev, const char *hcistr)
#else
static int usbhost_waiter(struct usbhost_connection_s *dev)
#endif
{
  bool connected[SAM_OHCI_NRHPORT] = {false, false, false};
  int rhpndx;
  int ret;

  uvdbg("%s Waiter Running\n", hcistr);
  for (;;)
    {
      /* Wait for the device to change state */

      rhpndx = CONN_WAIT(dev, connected);
      DEBUGASSERT(rhpndx >= 0 && rhpndx < SAM_OHCI_NRHPORT);

      connected[rhpndx] = !connected[rhpndx];

      uvdbg("%s RHport%d %s\n",
            hcistr, rhpndx + 1, connected[rhpndx] ? "connected" : "disconnected");

      /* Did we just become connected? */

      if (connected[rhpndx])
        {
          /* Yes.. enumerate the newly connected device */

          ret = CONN_ENUMERATE(dev, rhpndx);
          if (ret < 0)
            {
              uvdbg("%s RHport%d CONN_ENUMERATE failed: %d\n", hcistr, rhpndx+1, ret);
              connected[rhpndx] = false;
            }
        }
    }

  /* Keep the compiler from complaining */

  return 0;
}
#endif

/************************************************************************************
 * Name: ohci_waiter
 *
 * Description:
 *   Wait for USB devices to be connected to the OHCI hub.
 *
 ************************************************************************************/

#ifdef CONFIG_SAMA5_OHCI
static int ohci_waiter(int argc, char *argv[])
{
#ifdef CONFIG_DEBUG_USB
  return usbhost_waiter(g_ohciconn, "OHCI");
#else
  return usbhost_waiter(g_ohciconn);
#endif
}
#endif

/************************************************************************************
 * Name: ehci_waiter
 *
 * Description:
 *   Wait for USB devices to be connected to the EHCI hub.
 *
 ************************************************************************************/

#ifdef CONFIG_SAMA5_EHCI
static int ehci_waiter(int argc, char *argv[])
{
#ifdef CONFIG_DEBUG_USB
  return usbhost_waiter(g_ehciconn, "EHCI");
#else
  return usbhost_waiter(g_ehciconn);
#endif
}
#endif

/************************************************************************************
 * Public Functions
 ************************************************************************************/

/************************************************************************************
 * Name: sam_usbinitialize
 *
 * Description:
 *   Called from sam_usbinitialize very early in inialization to setup USB-related
 *   GPIO pins for the SAMA5D3x-EK board.
 *
 * USB Ports
 *   The SAMA5D3 series-MB features three USB communication ports:
 *
 *     1. Port A Host High Speed (EHCI) and Full Speed (OHCI) multiplexed with
 *        USB Device High Speed Micro AB connector, J20
 *
 *     2. Port B Host High Speed (EHCI) and Full Speed (OHCI) standard type A
 *        connector, J19 upper port
 *
 *     3. Port C Host Full Speed (OHCI) only standard type A connector, J19
 *        lower port
 *
 *   All three USB host ports are equipped with 500 mA high-side power switch
 *   for self-powered and buspowered applications. The USB device port feature
 *   VBUS inserts detection function.
 *
 *   Port A
 *
 *     PIO  Signal Name Function
 *     ---- ----------- -------------------------------------------------------
 *     PD29  VBUS_SENSE VBus detection
 *     PD25  EN5V_USBA  VBus power enable (via MN15 AIC1526 Dual USB High-Side
 *                      Power Switch.  The other channel of the switch is for
 *                      the LCD)
 *
 *   Port B
 *
 *     PIO  Signal Name Function
 *     ---- ----------- -------------------------------------------------------
 *     PD26 EN5V_USBB   VBus power enable (via MN14 AIC1526 Dual USB High-Side
 *                      Power Switch).  To the A1 pin of J19 Dual USB A
 *                      connector
 *
 *   Port C
 *
 *     PIO  Signal Name Function
 *     ---- ----------- -------------------------------------------------------
 *     PD27 EN5V_USBC   VBus power enable (via MN14 AIC1526 Dual USB High-Side
 *                      Power Switch).  To the B1 pin of J19 Dual USB A
 *                      connector
 *
 *    Both Ports B and C
 *
 *     PIO  Signal Name Function
 *     ---- ----------- -------------------------------------------------------
 *     PD28 OVCUR_USB   Combined overrcurrent indication from port A and B
 *
 * That offers a lot of flexibility.  However, here we enable the ports only
 * as follows:
 *
 *   Port A -- USB device
 *   Port B -- EHCI host
 *   Port C -- OHCI host
 *
 ************************************************************************************/

void weak_function sam_usbinitialize(void)
{
#ifdef HAVE_USBDEV
  /* Configure Port A to support the USB device function */

  sam_configpio(PIO_USBA_VBUS_SENSE); /* VBUS sense */

  /* TODO:  Configure an interrupt on VBUS sense */
#endif

#ifdef HAVE_USBHOST
#ifdef CONFIG_SAMA5_UHPHS_RHPORT1
  /* Configure Port A to support the USB OHCI/EHCI function */

  sam_configpio(PIO_USBA_VBUS_ENABLE); /* VBUS enable, initially OFF */
#endif

#ifdef CONFIG_SAMA5_UHPHS_RHPORT2
  /* Configure Port B to support the USB OHCI/EHCI function */

  sam_configpio(PIO_USBB_VBUS_ENABLE); /* VBUS enable, initially OFF */
#endif

#ifdef CONFIG_SAMA5_UHPHS_RHPORT3
  /* Configure Port C to support the USB OHCI/EHCI function */

  sam_configpio(PIO_USBC_VBUS_ENABLE); /* VBUS enable, initially OFF */
#endif

#if defined(CONFIG_SAMA5_UHPHS_RHPORT2) || defined(CONFIG_SAMA5_UHPHS_RHPORT3)
  /* Configure Port B/C VBUS overrcurrent detection */

  sam_configpio(PIO_USBBC_VBUS_OVERCURRENT); /* VBUS overcurrent */
#endif
#endif /* HAVE_USBHOST */
}

/***********************************************************************************
 * Name: sam_usbhost_initialize
 *
 * Description:
 *   Called at application startup time to initialize the USB host functionality.
 *   This function will start a thread that will monitor for device
 *   connection/disconnection events.
 *
 ***********************************************************************************/

#if HAVE_USBHOST
int sam_usbhost_initialize(void)
{
  pid_t pid;
  int ret;

  /* First, register all of the class drivers needed to support the drivers
   * that we care about
   *
   * Register theUSB host Mass Storage Class:
   */

  ret = usbhost_storageinit();
  if (ret != OK)
    {
      udbg("ERROR: Failed to register the mass storage class: %d\n", ret);
    }

  /* Register the USB host HID keyboard class driver */

  ret = usbhost_kbdinit();
  if (ret != OK)
    {
      udbg("ERROR: Failed to register the KBD class\n");
    }

  /* Then get an instance of the USB host interface. */

#ifdef CONFIG_SAMA5_OHCI
  /* Get an instance of the USB OHCI interface */

  g_ohciconn = sam_ohci_initialize(0);
  if (!g_ohciconn)
    {
      udbg("ERROR: sam_ohci_initialize failed\n");
      return -ENODEV;
    }

  /* Start a thread to handle device connection. */

  pid = task_create("OHCI Monitor", CONFIG_USBHOST_DEFPRIO,  CONFIG_USBHOST_STACKSIZE,
                    (main_t)ohci_waiter, (FAR char * const *)NULL);
  if (pid < 0)
    {
      udbg("ERROR: Failed to create ohci_waiter task: %d\n", ret);
      return -ENODEV;
    }
#endif

#ifdef CONFIG_SAMA5_EHCI
  /* Get an instance of the USB EHCI interface */

  g_ehciconn = sam_ehci_initialize(0);
  if (!g_ehciconn)
    {
      udbg("ERROR: sam_ehci_initialize failed\n");
      return -ENODEV;
    }

  /* Start a thread to handle device connection. */

  pid = task_create("EHCI Monitor", CONFIG_USBHOST_DEFPRIO,  CONFIG_USBHOST_STACKSIZE,
                    (main_t)ehci_waiter, (FAR char * const *)NULL);
  if (pid < 0)
    {
      udbg("ERROR: Failed to create ehci_waiter task: %d\n", ret);
      return -ENODEV;
    }
#endif

  return OK;
}
#endif

/***********************************************************************************
 * Name: sam_usbhost_vbusdrive
 *
 * Description:
 *   Enable/disable driving of VBUS 5V output.  This function must be provided by
 *   each platform that implements the OHCI or EHCI host interface
 *
 * Input Parameters:
 *   rhport - Selects root hub port to be powered host interface.  See SAM_RHPORT_*
 *            definitions above.
 *   enable - true: enable VBUS power; false: disable VBUS power
 *
 * Returned Value:
 *   None
 *
 ***********************************************************************************/

#if HAVE_USBHOST
void sam_usbhost_vbusdrive(int rhport, bool enable)
{
  pio_pinset_t pinset = 0;

  uvdbg("RHPort%d: enable=%d\n", rhport+1, enable);

  /* Pick the PIO configuration associated with the selected root hub port */

  switch (rhport)
    {
    case SAM_RHPORT1:
#ifndef CONFIG_SAMA5_UHPHS_RHPORT1
      udbg("ERROR: RHPort1 is not available in this configuration\n");
      return;
#else
      pinset = PIO_USBA_VBUS_ENABLE;
      break;
#endif

    case SAM_RHPORT2:
#ifndef CONFIG_SAMA5_UHPHS_RHPORT2
      udbg("ERROR: RHPort2 is not available in this configuration\n");
      return;
#else
      pinset = PIO_USBB_VBUS_ENABLE;
      break;
#endif

    case SAM_RHPORT3:
#ifndef CONFIG_SAMA5_UHPHS_RHPORT3
      udbg("ERROR: RHPort3 is not available in this configuration\n");
      return;
#else
      pinset = PIO_USBC_VBUS_ENABLE;
      break;
#endif

    default:
      udbg("ERROR: RHPort%d is not supported\n", rhport+1);
      return;
    }

  /* Then enable or disable VBUS power */

  if (enable)
    {
      /* Enable the Power Switch by driving the enable pin low */

      sam_piowrite(pinset, false);
    }
  else
    {
      /* Disable the Power Switch by driving the enable pin high */

      sam_piowrite(pinset, true);
    }
}
#endif

/************************************************************************************
 * Name: sam_setup_overcurrent
 *
 * Description:
 *   Setup to receive an interrupt-level callback if an overcurrent condition is
 *   detected on port B or C.
 *
 *   REVISIT: Since this is a common signal, we will need to come up with some way
 *   to inform both EHCI and OHCI drivers when this error occurs.
 *
 * Input Parameter:
 *   handler - New overcurrent interrupt handler
 *
 * Returned value:
 *   Old overcurrent interrupt handler
 *
 ************************************************************************************/

#if HAVE_USBHOST
xcpt_t sam_setup_overcurrent(xcpt_t handler)
{
#if defined(CONFIG_SAMA5_PIOD_IRQ) && (defined(CONFIG_SAMA5_UHPHS_RHPORT2) || \
    defined(CONFIG_SAMA5_UHPHS_RHPORT3))

  xcpt_t oldhandler;
  irqstate_t flags;

  /* Disable interrupts until we are done.  This guarantees that the
   * following operations are atomic.
   */

  flags = irqsave();

  /* Get the old button interrupt handler and save the new one */

  oldhandler  = g_ochandler;
  g_ochandler = handler;

  /* Configure the interrupt */

  sam_pioirq(PIO_USBBC_VBUS_OVERCURRENT);
  (void)irq_attach(IRQ_USBBC_VBUS_OVERCURRENT, handler);
  sam_pioirqenable(IRQ_USBBC_VBUS_OVERCURRENT);

  /* Return the old button handler (so that it can be restored) */

  irqrestore(flags);
  return oldhandler;

#else
  return NULL;

#endif
}
#endif /* CONFIG_SAMA5_PIOD_IRQ ... */

/************************************************************************************
 * Name:  sam_usbsuspend
 *
 * Description:
 *   Board logic must provide the sam_usbsuspend logic if the USBDEV driver is
 *   used.  This function is called whenever the USB enters or leaves suspend mode.
 *   This is an opportunity for the board logic to shutdown clocks, power, etc.
 *   while the USB is suspended.
 *
 ************************************************************************************/

#ifdef CONFIG_USBDEV
void sam_usbsuspend(FAR struct usbdev_s *dev, bool resume)
{
  ulldbg("resume: %d\n", resume);
}
#endif

#endif /* CONFIG_SAMA5_UHPHS || CONFIG_SAMA5_UDPHS */