|
|
/****************************************************************************************************
* configs/shenzhou/src/shenzhou-internal.h
* arch/arm/src/board/shenzhou-internal.n
*
* Copyright (C) 2012 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************************************/
#ifndef __CONFIGS_SHENZHOUL_SRC_SHENZHOU_INTERNAL_H
#define __CONFIGS_SHENZHOUL_SRC_SHENZHOU_INTERNAL_H
/****************************************************************************************************
* Included Files
****************************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
/****************************************************************************************************
* Definitions
****************************************************************************************************/
/* Configuration ************************************************************************************/
/* How many SPI modules does this chip support? */
#if STM32_NSPI < 1
# undef CONFIG_STM32_SPI1
# undef CONFIG_STM32_SPI2
# undef CONFIG_STM32_SPI3
#elif STM32_NSPI < 2
# undef CONFIG_STM32_SPI2
# undef CONFIG_STM32_SPI3
#elif STM32_NSPI < 3
# undef CONFIG_STM32_SPI3
#endif
/* Shenzhou GPIO Configuration **********************************************************************/
/* STM3240G-EVAL GPIOs ******************************************************************************/
/* Wireless
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 26 PA3 315M_VT
* 17 PC2 WIRELESS_INT
* 18 PC3 WIRELESS_CE To the NRF24L01 2.4G wireless module
* 59 PD12 WIRELESS_CS To the NRF24L01 2.4G wireless module
*/
#define GPIO_WIRELESS_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN12)
/* Buttons
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 23 PA0 WAKEUP Connected to KEY4. Active low: Closing KEY4 pulls WAKEUP to ground.
* 47 PB10 USERKEY Connected to KEY2
* 33 PC4 USERKEY2 Connected to KEY1
* 7 PC13 TAMPER Connected to KEY3
*/
/* BUTTONS -- NOTE that all have EXTI interrupts configured */
#define MIN_IRQBUTTON BUTTON_KEY1
#define MAX_IRQBUTTON BUTTON_KEY4
#define NUM_IRQBUTTONS (BUTTON_KEY4 - BUTTON_KEY1 + 1)
#define GPIO_BTN_WAKEUP (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTA|GPIO_PIN0)
#define GPIO_BTN_USERKEY (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTB|GPIO_PIN10)
#define GPIO_BTN_USERKEY2 (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTC|GPIO_PIN4)
#define GPIO_BTN_TAMPER (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTC|GPIO_PIN13)
/* LEDs
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 83 PD2 LED1 Active low: Pulled high
* 84 PD3 LED2 Active low: Pulled high
* 85 PD4 LED3 Active low: Pulled high
* 88 PD7 LED4 Active low: Pulled high
*/
#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN2)
#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN3)
#define GPIO_LED3 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN4)
#define GPIO_LED4 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN5)
/* TFT LCD
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 37 PB2 DATA_LE To TFT LCD (CN13)
* 96 PB9 F_CS To both the TFT LCD (CN13) and to the W25X16 SPI FLASH
* 34 PC5 TP_INT JP6. To TFT LCD (CN13) module
* 65 PC8 LCD_CS Active low: Pulled high
* 66 PC9 TP_CS Active low: Pulled high
* 60 PD13 LCD_RS To TFT LCD (CN13)
* 61 PD14 LCD_WR To TFT LCD (CN13)
* 62 PD15 LCD_RD To TFT LCD (CN13)
* 97 PE0 DB00 To TFT LCD (CN13)
* 98 PE1 DB01 To TFT LCD (CN13)
* 1 PE2 DB02 To TFT LCD (CN13)
* 2 PE3 DB03 To TFT LCD (CN13)
* 3 PE4 DB04 To TFT LCD (CN13)
* 4 PE5 DB05 To TFT LCD (CN13)
* 5 PE6 DB06 To TFT LCD (CN13)
* 38 PE7 DB07 To TFT LCD (CN13)
* 39 PE8 DB08 To TFT LCD (CN13)
* 40 PE9 DB09 To TFT LCD (CN13)
* 41 PE10 DB10 To TFT LCD (CN13)
* 42 PE11 DB11 To TFT LCD (CN13)
* 43 PE12 DB12 To TFT LCD (CN13)
* 44 PE13 DB13 To TFT LCD (CN13)
* 45 PE14 DB14 To TFT LCD (CN13)
* 46 PE15 DB15 To TFT LCD (CN13)
*/
#define GPIO_LCD_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9)
/* RS-485
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 88 PD7 485_DIR SP3485 read enable (not)
*/
/* To be provided */
/* USB
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 95 PB8 USB_PWR Drives USB VBUS
*/
#define GPIO_OTGFS_PWRON (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_SPEED_100MHz|\
GPIO_PUSHPULL|GPIO_PORTB|GPIO_PIN8)
/* Audio DAC
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
*/
/* To be provided */
/* SPI FLASH
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 96 PB9 F_CS To both the TFT LCD (CN13) and to the W25X16 SPI FLASH
*/
#define GPIO_FLASH_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9)
/* SD Card
*
* -- ---- -------------- -------------------------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- -------------------------------------------------------------------
* 53 PB14 SD_CD Active low: Pulled high
* 58 PD11 SD_CS
*/
#define GPIO_SD_CD (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTB|GPIO_PIN14)
#define GPIO_SD_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN11)
/****************************************************************************************************
* Public Types
****************************************************************************************************/
/****************************************************************************************************
* Public data
****************************************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************************************
* Public Functions
****************************************************************************************************/
/****************************************************************************************************
* Name: stm32_spiinitialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the STM3240G-EVAL board.
*
****************************************************************************************************/
void weak_function stm32_spiinitialize(void);
/****************************************************************************************************
* Name: stm32_usbinitialize
*
* Description:
* Called from stm32_usbinitialize very early in inialization to setup USB-related GPIO pins for
* the STM3240G-EVAL board.
*
****************************************************************************************************/
#ifdef CONFIG_STM32_OTGFS
void weak_function stm32_usbinitialize(void);
#endif
/****************************************************************************************************
* Name: stm32_usbhost_initialize
*
* Description:
* Called at application startup time to initialize the USB host functionality. This function will
* start a thread that will monitor for device connection/disconnection events.
*
****************************************************************************************************/
#if defined(CONFIG_STM32_OTGFS) && defined(CONFIG_USBHOST)
int stm32_usbhost_initialize(void);
#endif
/****************************************************************************
* Name: stm32_sdinitialize
*
* Description:
* Initialize the SPI-based SD card. Requires CONFIG_DISABLE_MOUNTPOINT=n
* and CONFIG_STM32_SPI1=y
*
****************************************************************************/
int stm32_sdinitialize(int minor);
/****************************************************************************
* Name: stm32_w25initialize
*
* Description:
* Initialize and register the W25 FLASH file system.
*
****************************************************************************/
#ifdef CONFIG_MTD_W25
int stm32_w25initialize(int minor);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_SHENZHOUL_SRC_SHENZHOU_INTERNAL_H */
|
