More Cortex-M0/NUC120 progress

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5669 42af7a65-404d-4744-a932-0658087f49c3

10 files changed, 200 insertions, 52 deletions

diff --git a/nuttx/arch/arm/src/armv6-m/up_exception.S b/nuttx/arch/arm/src/armv6-m/up_exception.S
index 4bc59126c..33f89b3b1 100644
--- a/nuttx/arch/arm/src/armv6-m/up_exception.S
+++ b/nuttx/arch/arm/src/armv6-m/up_exception.S
@@ -86,11 +86,11 @@
 	.type	exception_common, function
 exception_common:
 
-	mrs		r0, ipsr				/* R0=exception number */
-
 	/* Complete the context save */
 
-	/* The EXC_RETURN value tells us whether the context is on the MSP or PSP */
+	/* Get the current stack pointer.  The EXC_RETURN value tells us whether
+	 * the context is on the MSP or PSP.
+	 */
 
 	mov		r0, r14					/* Copy high register to low register */
 	lsl		r1, r0, #(31 - EXC_RETURN_PROCESS_BITNO)	/* Move to bit 31 */
@@ -101,15 +101,26 @@ exception_common:
 1:
 	mrs		r1, psp					/* R1=The process stack pointer */
 
+	/* R1 is the current stack pointer.  HW_XCPT_REGS were pushed onto the stack
+	 * when the interrupt was taken so (R1)+HW_XCPT_SIZE is the value of the
+	 * stack pointer before the interrupt.  The total size of the context save
+	 * area is XCPTCONTEXT_SIZE = SW_XCPT_SIZE + HW_XCPT_SIZE so (R1)-SW_XCPT_SIZE
+	 * is the address of the beginning of the context save area.
+	 */
+
 2:
-	mov		r2, #XCPTCONTEXT_SIZE	/* R2=Size of context array */
-	sub		r0, r1, r2				/* R0=Beginning of context array on the stack */
-	mov		r2, r1					/* R2=Copy of the main/process stack pointer */
-	add		r2, #HW_XCPT_SIZE		/* R2=MSP/PSP before the interrupt was taken */
+	/* Save SP, BASEPRI, and R4-R7 in the context array */
+
+	sub		r1, #SW_XCPT_SIZE		/* R1=Beginning of context array on the stack */
+	mov		r2, #XCPTCONTEXT_SIZE   /* R2=Size of the context array */
+	add		r2, r1					/* R2=MSP/PSP before the interrupt was taken */
 									/* (ignoring the xPSR[9] alignment bit) */
 	mrs		r3, basepri				/* R3=Current BASEPRI setting */
+	mov		r0, r1					/* Copy the context array pointer */
+	stmia	r0!, {r2-r7}			/* Save the SP, BASEPRI, and R4-R7 in the context array */
+
+	/* Save R8-R11 and the EXEC_RETURN value in the context array */
 
-	stmia	r0!, {r2-r7}			/* Save the SP, BASEPRI, and R4-R7 */
 	mov		r2, r8					/* Copy high registers to low */
 	mov		r3, r9
 	mov		r4, r10
@@ -117,6 +128,10 @@ exception_common:
 	mov		r6, r14
 	stmia	r0!, {r2-r6}			/* Save the high registers r8-r11 and r14 */
 
+	/* Get the exception number in R0=IRQ, R1=register save area on stack */
+
+	mrs		r0, ipsr				/* R0=exception number */
+
 	/* Disable interrupts, select the stack to use for interrupt handling
 	 * and call up_doirq to handle the interrupt
 	 */
@@ -134,9 +149,9 @@ exception_common:
 	bl		up_doirq				/* R0=IRQ, R1=register save area on stack */
 	pop		{r1}					/* Recover R1=main stack pointer */
 #else
-	msr	 msp, r1					/* We are using the main stack pointer */
+	msr		msp, r1					/* We are using the main stack pointer */
 	bl		up_doirq				/* R0=IRQ, R1=register save area on stack */
-	mrs	 r1, msp					/* Recover R1=main stack pointer */
+	mrs		r1, msp					/* Recover R1=main stack pointer */
 #endif
 
 	/* On return from up_doirq, r0 will hold a pointer to register context
@@ -173,26 +188,38 @@ exception_common:
 	 * the same stack frame that we created at entry.
 	 */
 
+	/* Recover R8-R11 and EXEC_RETURN (5 registers) */
+
 	mov		r2, #(4*REG_R8)			/* R2=Offset to R8 storage */
 	sub		r0, r1, r2				/* R0=Address of R8 storage */
-	ldmia	r0!, {r2-r6}			/* Recover R8-R11 and R14 */
+	ldmia	r0!, {r2-r6}			/* Recover R8-R11 and R14 (5 registers)*/
 	mov		r8, r2					/* Move to position in high registers */
 	mov		r9, r3
 	mov		r10, r4
 	mov		r11, r5
-	mov		r14, r6
+	mov		r14, r6					/* EXEC_RETURN */
+
+	/* Recover SP (R2), BASEPRI (R3), and R4-R7.  The size of the sofware saved
+	 * portion is 11 words.  5 were recovered above; 6 are recovered by the
+	 * ldmia below.  So adding (4*5) to r1 accounts for all of the software
+	 * saved registers.
+	 */
+
 	ldmia	r1!, {r2-r7}			/* Recover R4-R7 + 2 temp values */
+	add		r1, #(4*5)				/* R1=Value of MSP/PSP on exception entry */
 
-	/* The EXC_RETURN value tells us whether the context is on the MSP or PSP */
+	/* Restore the stack pointer.  The EXC_RETURN value tells us whether the
+	 * context is on the MSP or PSP.
+	 */
 
 	mov		r0, r14					/* Copy high register to low register */
 	lsl		r1, r0, #(31 - EXC_RETURN_PROCESS_BITNO)	/* Move to bit 31 */
 	bmi		5f						/* Test bit 31 */
-	mrs		r1, msp					/* R1=The main stack pointer */
+	msr		msp, r1					/* R1=The main stack pointer */
 	b		6f
 
 5:
-	mrs		r1, psp					/* R1=The process stack pointer */
+	msr		psp, r1					/* R1=The process stack pointer */
 
 6:
 	/* Restore the interrupt state */
diff --git a/nuttx/arch/arm/src/nuc1xx/Kconfig b/nuttx/arch/arm/src/nuc1xx/Kconfig
index bc590fbe2..5360f46ca 100644
--- a/nuttx/arch/arm/src/nuc1xx/Kconfig
+++ b/nuttx/arch/arm/src/nuc1xx/Kconfig
@@ -349,3 +349,49 @@ config NUC_I2S
 	default n
 
 endmenu
+
+config NUC_XTALLO
+	bool
+
+config NUC_INTHI
+	bool
+
+choice
+	prompt "SysTick clock source"
+	default NUC_SYSTICK_XTALHI
+
+config NUC_SYSTICK_XTALHI
+	bool "High speed XTAL clock"
+
+config NUC_SYSTICK_XTALLO
+	bool "Low speed XTAL clock"
+	select NUC_XTALLO
+
+config NUC_SYSTICK_XTALHId2
+	bool "High speed XTAL clock/2"
+
+config NUC_SYSTICK_HCLKd2
+	bool "HCLK/2"
+
+config NUC_SYSTICK_INTHId2
+	bool "Internal high speed clock/2"
+	select NUC_INTHI
+
+endchoice
+
+choice
+	prompt "NUC UART clock source"
+	default NUC_UARTCLK_INTHI
+	depends on NUC_UART0 || NUC_UART1 || NUC_UART2
+
+config NUC_UARTCLK_XTALHI
+	bool "External 4-24MHz high speed crystal"
+
+config NUC_UARTCLK_PLL
+	bool "PLL output"
+
+config NUC_UARTCLK_INTHI
+	bool "Internal 22.1184 high speed clock"
+	select NUC_INTHI
+
+endchoice
diff --git a/nuttx/arch/arm/src/nuc1xx/chip/nuc_clk.h b/nuttx/arch/arm/src/nuc1xx/chip/nuc_clk.h
index 17814a467..426efd782 100644
--- a/nuttx/arch/arm/src/nuc1xx/chip/nuc_clk.h
+++ b/nuttx/arch/arm/src/nuc1xx/chip/nuc_clk.h
@@ -47,6 +47,11 @@
 /********************************************************************************************
  * Pre-processor Definitions
  ********************************************************************************************/
+/* Well-known clock frequencies *************************************************************/
+
+#define NUC_INTHI_FREQUENCY        22118400
+#define NUC_INTLO_FREQUENCY        10000
+
 /* Register offsets *************************************************************************/
 
 #define NUC_CLK_PWRCON_OFFSET      0x0000 /* System power down control register */
diff --git a/nuttx/arch/arm/src/nuc1xx/nuc_clockconfig.c b/nuttx/arch/arm/src/nuc1xx/nuc_clockconfig.c
index 500856254..95e4332ce 100644
--- a/nuttx/arch/arm/src/nuc1xx/nuc_clockconfig.c
+++ b/nuttx/arch/arm/src/nuc1xx/nuc_clockconfig.c
@@ -125,10 +125,18 @@ void nuc_clockconfig(void)
 
   nuc_unlock();
 
-  /* Enable External 4~24 mhz high speed crystal */
+  /* Enable External 4~24 mhz high speed crystal (And other clocks if needed by
+   * other drivers).
+   */
 
   regval  = getreg32(NUC_CLK_PWRCON);
   regval |= CLK_PWRCON_XTL12M_EN;
+#ifdef CONFIG_NUC_XTALLO
+  regval |= CLK_PWRCON_XTL32K_EN;
+#endif
+#ifdef CONFIG_NUC_INTHI
+  regval |= CLK_PWRCON_OSC22M_EN;
+#endif
   putreg32(regval, NUC_CLK_PWRCON);
 
   /* Delay to assure that crystal input to be stable */
diff --git a/nuttx/arch/arm/src/nuc1xx/nuc_irq.c b/nuttx/arch/arm/src/nuc1xx/nuc_irq.c
index 62c17e1a9..ed62e7f43 100644
--- a/nuttx/arch/arm/src/nuc1xx/nuc_irq.c
+++ b/nuttx/arch/arm/src/nuc1xx/nuc_irq.c
@@ -257,8 +257,12 @@ void up_irqinitialize(void)
 
 void up_disable_irq(int irq)
 {
-  DEBUGASSERT(irq == NUC_IRQ_SYSTICK ||
-             (irq >= NUC_IRQ_INTERRUPT && irq < NR_IRQS));
+  /* This will be called on each interrupt (via up_maskack_irq()) whether
+   * the interrupt can be disabled or not.  So this assertion is necessarily
+   * lame.
+   */
+
+  DEBUGASSERT((unsigned)irq < NR_IRQS);
 
   /* Check for an external interrupt */
 
@@ -291,8 +295,11 @@ void up_disable_irq(int irq)
 
 void up_enable_irq(int irq)
 {
-  DEBUGASSERT(irq == NUC_IRQ_SYSTICK ||
-             (irq >= NUC_IRQ_INTERRUPT && irq < NR_IRQS));
+  /* This will be called on each interrupt exit whether the interrupt can be
+   * enambled or not.  So this assertion is necessarily lame.
+   */
+
+  DEBUGASSERT((unsigned)irq < NR_IRQS);
 
   /* Check for external interrupt */
 
diff --git a/nuttx/arch/arm/src/nuc1xx/nuc_lowputc.c b/nuttx/arch/arm/src/nuc1xx/nuc_lowputc.c
index 77b744948..ec0c192d2 100644
--- a/nuttx/arch/arm/src/nuc1xx/nuc_lowputc.c
+++ b/nuttx/arch/arm/src/nuc1xx/nuc_lowputc.c
@@ -82,6 +82,18 @@
 #  endif
 #endif
 
+/* Select either the external high speed crystal, the PLL output, or
+ * the internal high speed clock as the the UART clock source.
+ */
+
+#if defined(CONFIG_NUC_UARTCLK_XTALHI)
+#  define NUC_UART_CLK BOARD_XTALHI_FREQUENCY
+#elif defined(CONFIG_NUC_UARTCLK_PLL)
+#  define NUC_UART_CLK BOARD_PLL_FOUT
+#elif defined(CONFIG_NUC_UARTCLK_INTHI)
+#  define NUC_UART_CLK NUC_INTHI_FREQUENCY
+#endif
+
 /****************************************************************************
  * Private Functions
  ****************************************************************************/
@@ -177,12 +189,22 @@ void nuc_lowsetup(void)
   putreg32(regval, NUC_GCR_IPRSTC2);
 #endif
 
-  /* Configure the UART clock source 
-   *
-   * Here we assume that the UART clock source is the external high speed
-   * crystal -- the power on default value in the CLKSEL0 register.
+  /* Configure the UART clock source. Set the UART clock source to either
+   * the external high speed crystal (CLKSEL1 reset value), the PLL output,
+   * or the internal high speed clock.
    */
 
+  regval  = getreg32(NUC_CLK_CLKSEL1);
+  regval &= ~CLK_CLKSEL1_UART_S_MASK;
+#if defined(CONFIG_NUC_UARTCLK_XTALHI)
+  regval |= CLK_CLKSEL1_UART_S_XTALHI;
+#elif defined(CONFIG_NUC_UARTCLK_PLL)
+  regval |= CLK_CLKSEL1_UART_S_PLL;
+#elif defined(CONFIG_NUC_UARTCLK_INTHI)
+  regval |= CLK_CLKSEL1_UART_S_INTHI;
+#endif
+  putreg32(regval, NUC_CLK_CLKSEL1);
+
   /* Enable UART clocking for the selected UARTs */
 
   regval = getreg32(NUC_CLK_APBCLK);
@@ -206,15 +228,13 @@ void nuc_lowsetup(void)
 
   /* Reset the TX FIFO */
 
-  regval = getreg32(NUC_CONSOLE_BASE + NUC_UART_FCR_OFFSET);
-  regval |= UART_FCR_TFR;
-  putreg32(regval, NUC_CONSOLE_BASE + NUC_UART_FCR_OFFSET);
+  regval  = getreg32(NUC_CONSOLE_BASE + NUC_UART_FCR_OFFSET);
+  regval &= ~(UART_FCR_TFR | UART_FCR_RFR);
+  putreg32(regval | UART_FCR_TFR, NUC_CONSOLE_BASE + NUC_UART_FCR_OFFSET);
 
   /* Reset the RX FIFO */
 
-  regval = getreg32(NUC_CONSOLE_BASE + NUC_UART_FCR_OFFSET);
-  regval |= UART_FCR_RFR;
-  putreg32(regval, NUC_CONSOLE_BASE + NUC_UART_FCR_OFFSET);
+  putreg32(regval | UART_FCR_RFR, NUC_CONSOLE_BASE + NUC_UART_FCR_OFFSET);
 
   /* Set Rx Trigger Level */
 
@@ -243,7 +263,6 @@ void nuc_lowsetup(void)
   regval |= (UART_LCR_PBE | UART_LCR_EPE);
 #endif
 
-
 #if NUC_CONSOLE_2STOP != 0
   revgval |= UART_LCR_NSB;
 #endif
@@ -292,9 +311,9 @@ void nuc_lowputc(uint32_t ch)
  *
  *   Mode DIV_X_EN DIV_X_ONE Divider X   BRD  (Baud rate equation)
  *   -------------------------------------------------------------
- *   0    Disable  0         B           A    UART_CLK / [16 * (A+2)]
- *   1    Enable   0         B           A    UART_CLK / [(B+1) * (A+2)] , B must >= 8
- *   2    Enable   1         Don't care  A    UART_CLK / (A+2), A must >=3
+ *    0       0        0         B        A   UART_CLK / [16 * (A+2)]
+ *    1       1        0         B        A   UART_CLK / [(B+1) * (A+2)] , B must >= 8
+ *    2       1        1     Don't care   A   UART_CLK / (A+2), A must >=3
  *
  * Here we assume that the default clock source for the UART modules is
  * the external high speed crystal.
@@ -311,9 +330,9 @@ void nuc_setbaud(uintptr_t base, uint32_t baud)
 
   regval = getreg32(base + NUC_UART_BAUD_OFFSET);
   
-   /* Source Clock mod 16 < 3 => Using Divider X = 16 (MODE#0) */
+   /* Mode 0: Source Clock mod 16 < 3 => Using Divider X = 16 */
 
-  clksperbit = BOARD_HIGHSPEED_XTAL_FREQUENCY / baud;
+  clksperbit = (NUC_UART_CLK + (baud >> 1)) / baud;
   if ((clksperbit & 15) < 3)          
     {
       regval &= ~(UART_BAUD_DIV_X_ONE | UART_BAUD_DIV_X_EN);
@@ -324,7 +343,7 @@ void nuc_setbaud(uintptr_t base, uint32_t baud)
 
   else
     {
-      /* Try to Set Divider X = 1 (MODE#2)*/
+      /* Mode 2: Try to Set Divider X = 1 */
 
       regval |= (UART_BAUD_DIV_X_ONE | UART_BAUD_DIV_X_EN);
       brd = clksperbit - 2;
@@ -333,13 +352,13 @@ void nuc_setbaud(uintptr_t base, uint32_t baud)
 
       if (brd > 0xffff)
         {
-          /* Try to Set Divider X up 10 (MODE#1) */
+          /* Mode 1: Try to Set Divider X up 10 */
 
           regval &= ~UART_BAUD_DIV_X_ONE;
    
           for (divx = 8; divx < 16; divx++)
             {
-              brd = (clksperbit % (divx + 1));
+              brd = clksperbit % (divx + 1);
               if (brd < 3)
                 {
                   regval &= ~UART_BAUD_DIVIDER_X_MASK;
@@ -355,6 +374,5 @@ void nuc_setbaud(uintptr_t base, uint32_t baud)
   regval &= ~UART_BAUD_BRD_MASK;
   regval |= UART_BAUD_BRD(brd);
   putreg32(regval, base + NUC_UART_BAUD_OFFSET);
-
 }
 #endif /* HAVE_UART */
diff --git a/nuttx/arch/arm/src/nuc1xx/nuc_timerisr.c b/nuttx/arch/arm/src/nuc1xx/nuc_timerisr.c
index c27474601..fdadbf23e 100644
--- a/nuttx/arch/arm/src/nuc1xx/nuc_timerisr.c
+++ b/nuttx/arch/arm/src/nuc1xx/nuc_timerisr.c
@@ -51,22 +51,33 @@
 #include "up_arch.h"
 
 #include "chip.h"
+#include "chip/nuc_clk.h"
 
 /****************************************************************************
  * Pre-processor Definitions
  ****************************************************************************/
+/* Get the frequency of the selected clock source */
+
+#if defined(CONFIG_NUC_SYSTICK_XTALHI)
+#  define SYSTICK_CLOCK BOARD_XTALHI_FREQUENCY     /* High speed XTAL clock */
+#elif defined(CONFIG_NUC_SYSTICK_XTALLO)
+#  define SYSTICK_CLOCK BOARD_XTALLO_FREQUENCY     /* Low speed XTAL clock */
+#elif defined(CONFIG_NUC_SYSTICK_XTALHId2)
+#  define SYSTICK_CLOCK (BOARD_XTALHI_FREQUENCY/2) /* High speed XTAL clock/2 */
+#elif defined(CONFIG_NUC_SYSTICK_HCLKd2)
+#  define SYSTICK_CLOCK (BOARD_HCLK_FREQUENCY/2)   /* HCLK/2 */
+#elif defined(CONFIG_NUC_SYSTICK_INTHId2)
+#  define SYSTICK_CLOCK (NUC_INTHI_FREQUENCY/2)    /* Internal high speed clock/2 */
+#endif
 
 /* The desired timer interrupt frequency is provided by the definition
  * CLK_TCK (see include/time.h).  CLK_TCK defines the desired number of
  * system clock ticks per second.  That value is a user configurable setting
  * that defaults to 100 (100 ticks per second = 10 MS interval).
  *
- * Here we assume that the default clock source for the SysTick is the
- * external high speed crystal -- the power-on default value for the
- * CLKSEL0 register
- *
- * Then, for example, if BOARD_HIGHSPEED_XTAL_FREQUENCY is 12MHz and
- * CLK_TCK is 100, the the reload value would be:
+ * Then, for example, if the external high speed crystal is the SysTick
+ * clock source and BOARD_XTALHI_FREQUENCY is 12MHz and CLK_TCK is 100, then
+ * the reload value would be:
  *
  *   SYSTICK_RELOAD = (12,000,000 / 100) - 1
  *                  = 119,999
@@ -75,7 +86,7 @@
  * Which fits within the maximum 14-bit reload value.
  */
 
-#define SYSTICK_RELOAD ((BOARD_HIGHSPEED_XTAL_FREQUENCY / CLK_TCK) - 1)
+#define SYSTICK_RELOAD ((SYSTICK_CLOCK / CLK_TCK) - 1)
 
 /* The size of the reload field is 24 bits.  Verify that the reload value
  * will fit in the reload register.
@@ -127,6 +138,23 @@ void up_timerinit(void)
 {
   uint32_t regval;
 
+  /* Configure the SysTick clock source.*/
+
+  regval  = getreg32(NUC_CLK_CLKSEL0);
+  regval &= ~CLK_CLKSEL0_STCLK_S_MASK;
+#if defined(CONFIG_NUC_SYSTICK_XTALHI)
+  regval |= CLK_CLKSEL0_STCLK_S_XTALHI;   /* High speed XTAL clock */
+#elif defined(CONFIG_NUC_SYSTICK_XTALLO)
+  regval |= CLK_CLKSEL0_STCLK_S_XTALLO;   /* Low speed XTAL clock */
+#elif defined(CONFIG_NUC_SYSTICK_XTALHId2)
+  regval |= CLK_CLKSEL0_STCLK_S_XTALDIV2; /* High speed XTAL clock/2 */
+#elif defined(CONFIG_NUC_SYSTICK_HCLKd2)
+  regval |= CLK_CLKSEL0_STCLK_S_HCLKDIV2; /* HCLK/2 */
+#elif defined(CONFIG_NUC_SYSTICK_INTHId2)
+  regval |= CLK_CLKSEL0_STCLK_S_INTDIV2;  /* Internal high speed clock/2 */
+#endif
+  putreg32(regval, NUC_CLK_CLKSEL0);
+
   /* Set the SysTick interrupt to the default priority */
 
   regval = getreg32(ARMV6M_SYSCON_SHPR3);
diff --git a/nuttx/configs/nutiny-nuc120/README.txt b/nuttx/configs/nutiny-nuc120/README.txt
index 3333866db..f1e8aa0c6 100644
--- a/nuttx/configs/nutiny-nuc120/README.txt
+++ b/nuttx/configs/nutiny-nuc120/README.txt
@@ -100,8 +100,8 @@ is provided as an LQFP48 package and, for this case, the UART1 RX signal
 (RXD1) is on PB.4, pin 8, and the TX signal (TXD1) is on PB.5, pin 9.
 These pins are available on the NuTiny-SDC-NUC120 JP5.
 
-  NOTE: The TX vs RX terminology is confusing.  On my RS-232 driver board,
-  I need to connect the NUC120 TXD0 pin to the driver boards RXD pin.  How
+  NOTE: The TX vs RX labeling may be confusing.  On one RS-232 driver board,
+  I had to connect the NUC120 TXD0 pin to the driver boards RXD pin.  How
   confusing!
 
 UART0 is an alternative that can be selected by modifying the default
diff --git a/nuttx/configs/nutiny-nuc120/include/board.h b/nuttx/configs/nutiny-nuc120/include/board.h
index 47b43c044..bd4a0013b 100644
--- a/nuttx/configs/nutiny-nuc120/include/board.h
+++ b/nuttx/configs/nutiny-nuc120/include/board.h
@@ -53,8 +53,8 @@
 /* Clocking *************************************************************************/
 /* Crystal frequencies */
 
-#define BOARD_HIGHSPEED_XTAL_FREQUENCY 12000000
-#define BOARD_LOWSPEED_XTAL_FREQUENCY  32768
+#define BOARD_XTALHI_FREQUENCY 12000000
+#define BOARD_XTALLO_FREQUENCY 32768
 
 /* PLL: The PLL must be 48MHz x N times when using USB
  *
@@ -72,7 +72,7 @@
  *      = 48MHz
  */
 
-#define BOARD_PLL_FIN    BOARD_HIGHSPEED_XTAL_FREQUENCY
+#define BOARD_PLL_FIN    BOARD_XTALHI_FREQUENCY
 #define BOARD_PLL_FB_DV  46
 #define BOARD_PLL_NF     (BOARD_PLL_FB_DV+2)
 #define BOARD_PLL_IN_DV  1
diff --git a/nuttx/configs/nutiny-nuc120/ostest/defconfig b/nuttx/configs/nutiny-nuc120/ostest/defconfig
index 81d3f3eec..c7280484c 100644
--- a/nuttx/configs/nutiny-nuc120/ostest/defconfig
+++ b/nuttx/configs/nutiny-nuc120/ostest/defconfig
@@ -163,6 +163,15 @@ CONFIG_NUC_UART1=y
 # CONFIG_NUC_ADC is not set
 # CONFIG_NUC_PS2 is not set
 # CONFIG_NUC_I2S is not set
+CONFIG_NUC_INTHI=y
+CONFIG_NUC_SYSTICK_XTALHI=y
+# CONFIG_NUC_SYSTICK_XTALLO is not set
+# CONFIG_NUC_SYSTICK_XTALHId2 is not set
+# CONFIG_NUC_SYSTICK_HCLKd2 is not set
+# CONFIG_NUC_SYSTICK_INTHId2 is not set
+# CONFIG_NUC_UARTCLK_XTALHI is not set
+# CONFIG_NUC_UARTCLK_PLL is not set
+CONFIG_NUC_UARTCLK_INTHI=y
 
 #
 # External Memory Configuration