Adds support for the STM32F103VCT6 and for the Hy-Mini STM32v board. Contributed by Laurent Latil

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4197 42af7a65-404d-4744-a932-0658087f49c3

58 files changed, 14150 insertions, 0 deletions

diff --git a/nuttx/configs/hymini-stm32v/README.txt b/nuttx/configs/hymini-stm32v/README.txt
new file mode 100755
index 000000000..016604d88
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/README.txt
@@ -0,0 +1,674 @@
+README
+======
+
+This README discusses issues unique to NuttX configurations for the
+HY-MiniSTM32V development board.
+
+Contents
+========
+
+  - Development Environment
+  - GNU Toolchain Options
+  - IDEs
+  - NuttX buildroot Toolchain
+  - DFU
+  - LEDs
+  - RTC
+  - HY-Mini specific Configuration Options
+  - Configurations
+
+Development Environment
+=======================
+
+  Either Linux or Cygwin on Windows can be used for the development environment.
+  The source has been built only using the GNU toolchain (see below).  Other
+  toolchains will likely cause problems. Testing was performed using the Cygwin
+  environment because the Raisonance R-Link emulatator and some RIDE7 development tools
+  were used and those tools works only under Windows.
+
+GNU Toolchain Options
+=====================
+
+  The NuttX make system has been modified to support the following different
+  toolchain options.
+
+  1. The CodeSourcery GNU toolchain,
+  2. The devkitARM GNU toolchain,
+  3. Raisonance GNU toolchain, or
+  4. The NuttX buildroot Toolchain (see below).
+
+  All testing has been conducted using the NuttX buildroot toolchain.  However,
+  the make system is setup to default to use the devkitARM toolchain.  To use
+  the CodeSourcery, devkitARM or Raisonance GNU toolchain, you simply need to
+  add one of the following configuration options to your .config (or defconfig)
+  file:
+
+    CONFIG_STM32_CODESOURCERYW=y  : CodeSourcery under Windows
+    CONFIG_STM32_CODESOURCERYL=y  : CodeSourcery under Linux
+    CONFIG_STM32_DEVKITARM=y      : devkitARM under Windows
+    CONFIG_STM32_RAISONANCE=y     : Raisonance RIDE7 under Windows
+    CONFIG_STM32_BUILDROOT=y	  : NuttX buildroot under Linux or Cygwin (default)
+
+  If you are not using CONFIG_STM32_BUILDROOT, then you may also have to modify
+  the PATH in the setenv.h file if your make cannot find the tools.
+
+  NOTE: the CodeSourcery (for Windows), devkitARM, and Raisonance toolchains are
+  Windows native toolchains.  The CodeSourcey (for Linux) and NuttX buildroot
+  toolchains are Cygwin and/or Linux native toolchains. There are several limitations
+  to using a Windows based toolchain in a Cygwin environment.  The three biggest are:
+
+  1. The Windows toolchain cannot follow Cygwin paths.  Path conversions are
+     performed automatically in the Cygwin makefiles using the 'cygpath' utility
+     but you might easily find some new path problems.  If so, check out 'cygpath -w'
+
+  2. Windows toolchains cannot follow Cygwin symbolic links.  Many symbolic links
+     are used in Nuttx (e.g., include/arch).  The make system works around these
+     problems for the Windows tools by copying directories instead of linking them.
+     But this can also cause some confusion for you:  For example, you may edit
+     a file in a "linked" directory and find that your changes had no effect.
+     That is because you are building the copy of the file in the "fake" symbolic
+     directory.  If you use a Windows toolchain, you should get in the habit of
+     making like this:
+
+       make clean_context all
+
+     An alias in your .bashrc file might make that less painful.
+
+  3. Dependencies are not made when using Windows versions of the GCC.  This is
+     because the dependencies are generated using Windows pathes which do not
+     work with the Cygwin make.
+
+     Support has been added for making dependencies with the windows-native toolchains.
+     That support can be enabled by modifying your Make.defs file as follows:
+
+    -  MKDEP                = $(TOPDIR)/tools/mknulldeps.sh
+    +  MKDEP                = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
+
+     If you have problems with the dependency build (for example, if you are not
+     building on C:), then you may need to modify tools/mkdeps.sh
+
+  NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
+  level of -Os (See Make.defs).  It will work with -O0, -O1, or -O2, but not with
+  -Os.
+
+  NOTE 2: The devkitARM toolchain includes a version of MSYS make.  Make sure that
+  the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
+  path or will get the wrong version of make.
+
+IDEs
+====
+
+  NuttX is built using command-line make.  It can be used with an IDE, but some
+  effort will be required to create the project (There is a simple RIDE project
+  in the RIDE subdirectory).
+  
+  Makefile Build
+  --------------
+  Under Eclipse, it is pretty easy to set up an "empty makefile project" and
+  simply use the NuttX makefile to build the system.  That is almost for free
+  under Linux.  Under Windows, you will need to set up the "Cygwin GCC" empty
+  makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
+  there is a lot of help on the internet).
+
+  Native Build
+  ------------
+  Here are a few tips before you start that effort:
+
+  1) Select the toolchain that you will be using in your .config file
+  2) Start the NuttX build at least one time from the Cygwin command line
+     before trying to create your project.  This is necessary to create
+     certain auto-generated files and directories that will be needed.
+  3) Set up include pathes:  You will need include/, arch/arm/src/stm32,
+     arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
+  4) All assembly files need to have the definition option -D __ASSEMBLY__
+     on the command line.
+
+  Startup files will probably cause you some headaches.  The NuttX startup file
+  is arch/arm/src/stm32/stm32_vectors.S.  With RIDE, I have to build NuttX
+  one time from the Cygwin command line in order to obtain the pre-built
+  startup object needed by RIDE.
+
+NuttX buildroot Toolchain
+=========================
+
+  A GNU GCC-based toolchain is assumed.  The files */setenv.sh should
+  be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
+  different from the default in your PATH variable).
+
+  If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
+  SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
+  This GNU toolchain builds and executes in the Linux or Cygwin environment.
+
+  1. You must have already configured Nuttx in <some-dir>/nuttx.
+
+     cd tools
+     ./configure.sh hymini-stm32v/<sub-dir>
+
+  2. Download the latest buildroot package into <some-dir>
+
+  3. unpack the buildroot tarball.  The resulting directory may
+     have versioning information on it like buildroot-x.y.z.  If so,
+     rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
+
+  4. cd <some-dir>/buildroot
+
+  5. cp configs/cortexm3-defconfig-4.3.3 .config
+
+  6. make oldconfig
+
+  7. make
+
+  8. Edit setenv.h, if necessary, so that the PATH variable includes
+     the path to the newly built binaries.
+
+  See the file configs/README.txt in the buildroot source tree.  That has more
+  detailed PLUS some special instructions that you will need to follow if you are
+  building a Cortex-M3 toolchain for Cygwin under Windows.
+
+DFU
+===
+
+  The linker files in these projects can be configured to indicate that you
+  will be loading code using STMicro built-in USB Device Firmware Upgrade (DFU)
+  loader or via some JTAG emulator.  You can specify the DFU bootloader by
+  adding the following line:
+
+    CONFIG_STM32_DFU=y
+
+  to your .config file. Most of the configurations in this directory are set
+  up to use the DFU loader.
+
+  If CONFIG_STM32_DFU is defined, the code will not be positioned at the beginning
+  of FLASH (0x08000000) but will be offset to 0x08003000.  This offset is needed
+  to make space for the DFU loader and 0x08003000 is where the DFU loader expects
+  to find new applications at boot time.  If you need to change that origin for some
+  other bootloader, you will need to edit the file(s) ld.script.dfu for each
+  configuration.
+
+  The DFU SE PC-based software is available from the STMicro website,
+  http://www.st.com.  General usage instructions:
+  
+  1. Convert the NuttX Intel Hex file (nuttx.ihx) into a special DFU
+     file (nuttx.dfu)... see below for details.
+  2. Connect the Hy-Mini STM32v board to your computer using a USB
+     cable.
+  3. Start the DFU loader on the Hy-Mini STM32v board.  You do this by
+     resetting the board while holding the "Key" button.  Windows should
+     recognize that the DFU loader has been installed.
+  3. Run the DFU SE program to load nuttx.dfu into FLASH.
+
+  What if the DFU loader is not in FLASH?  The loader code is available
+  inside of the Demo dirctory of the USBLib ZIP file that can be downloaded
+  from the STMicro Website.  You can build it using RIDE (or other toolchains);
+  you will need a JTAG emulator to burn it into FLASH the first time.
+
+  In order to use STMicro's built-in DFU loader, you will have to get
+  the NuttX binary into a special format with a .dfu extension.  The
+  DFU SE PC_based software installation includes a file "DFU File Manager"
+  conversion program that a file in Intel Hex format to the special DFU
+  format.  When you successfully build NuttX, you will find a file called
+  nutt.ihx in the top-level directory.  That is the file that you should
+  provide to the DFU File Manager.  You will need to rename it to nuttx.hex
+  in order to find it with the DFU File Manager. You will end up with
+  a file called nuttx.dfu that you can use with the STMicro DFU SE program.
+
+LEDs
+====
+
+The HY-MiniSTM32 board provides only two controlable LEDs labeled LED1 and LED2.
+Usage of these LEDs is defined in include/board.h and src/up_leds.c.
+They are encoded as follows:
+
+	SYMBOL				Meaning					LED1*	LED2	
+	-------------------	-----------------------	-------	-------	
+	LED_STARTED			NuttX has been started	OFF		OFF		
+	LED_HEAPALLOCATE	Heap has been allocated	ON		OFF		
+	LED_IRQSENABLED		Interrupts enabled		OFF		ON		
+	LED_STACKCREATED	Idle stack created		ON		OFF		
+	LED_INIRQ			In an interrupt**		OFF		N/C		
+	LED_SIGNAL			In a signal handler***  N/C		ON		
+	LED_ASSERTION		An assertion failed		ON		ON		
+	LED_PANIC			The system has crashed	BLINK	BLINK		
+    LED_IDLE            STM32 is is sleep mode  (Optional, not used)
+
+  * If Nuttx starts correctly, normal state is to have LED1 on and LED2 off.
+ ** LED1 is turned off during interrrupt.
+*** LED2 is turned on during signal handler.
+
+RTC
+===
+
+  The STM32 RTC may configured using the following settings.
+
+    CONFIG_RTC - Enables general support for a hardware RTC. Specific
+      architectures may require other specific settings.
+    CONFIG_RTC_HIRES - The typical RTC keeps time to resolution of 1
+      second, usually supporting a 32-bit time_t value.  In this case,
+      the RTC is used to &quot;seed&quot; the normal NuttX timer and the
+      NuttX timer provides for higher resoution time. If CONFIG_RTC_HIRES
+      is enabled in the NuttX configuration, then the RTC provides higher
+      resolution time and completely replaces the system timer for purpose of
+      date and time.
+      CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the
+      frequency of the high resolution RTC must be provided.  If CONFIG_RTC_HIRES
+      is not defined, CONFIG_RTC_FREQUENCY is assumed to be one.
+    CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an alarm. 
+      A callback function will be executed when the alarm goes off
+
+  In hi-res mode, the STM32 RTC operates only at 16384Hz.  Overflow interrupts
+  are handled when the 32-bit RTC counter overflows every 3 days and 43 minutes.
+  A BKP register is incremented on each overflow interrupt creating, effectively,
+  a 48-bit RTC counter.
+
+  In the lo-res mode, the RTC operates at 1Hz.  Overflow interrupts are not handled
+  (because the next overflow is not expected until the year 2106.
+
+   WARNING:  Overflow interrupts are lost whenever the STM32 is powered down.  The
+   overflow interrupt may be lost even if the STM32 is powered down only momentarily.
+   Therefore hi-res solution is only useful in systems where the power is always on.
+
+HY-Mini specific Configuration Options
+============================================
+
+	CONFIG_ARCH - Identifies the arch/ subdirectory.  This should
+	   be set to:
+
+	   CONFIG_ARCH=arm
+
+	CONFIG_ARCH_family - For use in C code:
+
+	   CONFIG_ARCH_ARM=y
+
+	CONFIG_ARCH_architecture - For use in C code:
+
+	   CONFIG_ARCH_CORTEXM3=y
+
+	CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+
+	   CONFIG_ARCH_CHIP=stm32
+
+	CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
+	   chip:
+
+	   CONFIG_ARCH_CHIP_STM32F103VCT6
+
+    CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
+       configuration features.
+
+       CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
+ 
+	CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
+	   hence, the board that supports the particular chip or SoC.
+
+	   CONFIG_ARCH_BOARD=hymini-stm32v (for the HY-Mini development board)
+
+	CONFIG_ARCH_BOARD_name - For use in C code
+
+	   CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+
+	CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
+	   of delay loops
+
+	CONFIG_ENDIAN_BIG - define if big endian (default is little
+	   endian)
+
+	CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
+
+	   CONFIG_DRAM_SIZE=0x0000C000 (48Kb)
+
+	CONFIG_DRAM_START - The start address of installed DRAM
+
+	   CONFIG_DRAM_START=0x20000000
+
+	CONFIG_DRAM_END - Last address+1 of installed RAM
+
+	   CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+
+	CONFIG_ARCH_IRQPRIO - The STM32F103V supports interrupt prioritization
+
+	   CONFIG_ARCH_IRQPRIO=y
+
+	CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
+	   have LEDs
+
+	CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+	   stack. If defined, this symbol is the size of the interrupt
+	   stack in bytes.  If not defined, the user task stacks will be
+	   used during interrupt handling.
+
+	CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+
+	CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+
+	CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+	   cause a 100 second delay during boot-up.  This 100 second delay
+	   serves no purpose other than it allows you to calibratre
+	   CONFIG_ARCH_LOOPSPERMSEC.  You simply use a stop watch to measure
+	   the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
+	   the delay actually is 100 seconds.
+
+  Individual subsystems can be enabled:
+	AHB
+	---
+	CONFIG_STM32_DMA1
+	CONFIG_STM32_DMA2
+	CONFIG_STM32_CRC
+	CONFIG_STM32_FSMC
+	CONFIG_STM32_SDIO
+
+	APB1
+	----
+	CONFIG_STM32_TIM2
+	CONFIG_STM32_TIM3    (required for PWM control of LCD backlight)
+	CONFIG_STM32_TIM4
+	CONFIG_STM32_TIM5
+	CONFIG_STM32_TIM6
+	CONFIG_STM32_TIM7
+	CONFIG_STM32_WWDG
+	CONFIG_STM32_SPI2
+	CONFIG_STM32_SPI4
+	CONFIG_STM32_USART2
+	CONFIG_STM32_USART3
+	CONFIG_STM32_UART4
+	CONFIG_STM32_UART5
+	CONFIG_STM32_I2C1
+	CONFIG_STM32_I2C2
+	CONFIG_STM32_USB
+	CONFIG_STM32_CAN
+	CONFIG_STM32_BKP
+	CONFIG_STM32_PWR
+	CONFIG_STM32_DAC
+	CONFIG_STM32_USB
+
+	APB2
+	----
+	CONFIG_STM32_ADC1
+	CONFIG_STM32_ADC2
+	CONFIG_STM32_TIM1
+	CONFIG_STM32_SPI1
+	CONFIG_STM32_TIM8
+	CONFIG_STM32_USART1
+	CONFIG_STM32_ADC3
+
+  Timer and I2C devices may need to the following to force power to be applied
+  unconditionally at power up.  (Otherwise, the device is powered when it is
+  initialized).
+
+    CONFIG_STM32_FORCEPOWER
+
+  The Timer3 alternate mapping is required for PWM control of LCD backlight
+  
+    CONFIG_STM32_TIM3_PARTIAL_REMAP=y
+    
+  Timer devices may be used for different purposes.  One special purpose is
+  to generate modulated outputs for such things as motor control.  If CONFIG_STM32_TIMn
+  is defined (as above) then the following may also be defined to indicate that
+  the timer is intended to be used for pulsed output modulation, ADC conversion,
+  or DAC conversion.
+
+	CONFIG_STM32_TIM1_PWM
+	CONFIG_STM32_TIM2_PWM
+	CONFIG_STM32_TIM3_PWM
+	CONFIG_STM32_TIM4_PWM
+	CONFIG_STM32_TIM5_PWM
+	CONFIG_STM32_TIM6_PWM
+	CONFIG_STM32_TIM7_PWM
+	CONFIG_STM32_TIM8_PWM
+
+	CONFIG_STM32_TIM1_ADC
+	CONFIG_STM32_TIM2_ADC
+	CONFIG_STM32_TIM3_ADC
+	CONFIG_STM32_TIM4_ADC
+	CONFIG_STM32_TIM5_ADC
+	CONFIG_STM32_TIM6_ADC
+	CONFIG_STM32_TIM7_ADC
+	CONFIG_STM32_TIM8_ADC
+
+	CONFIG_STM32_TIM1_DAC
+	CONFIG_STM32_TIM2_DAC
+	CONFIG_STM32_TIM3_DAC
+	CONFIG_STM32_TIM4_DAC
+	CONFIG_STM32_TIM5_DAC
+	CONFIG_STM32_TIM6_DAC
+	CONFIG_STM32_TIM7_DAC
+	CONFIG_STM32_TIM8_DAC
+
+  Others alternate pin mappings available:
+
+	CONFIG_STM32_TIM1_FULL_REMAP
+	CONFIG_STM32_TIM1_PARTIAL_REMAP
+	CONFIG_STM32_TIM2_FULL_REMAP
+	CONFIG_STM32_TIM2_PARTIAL_REMAP_1
+	CONFIG_STM32_TIM2_PARTIAL_REMAP_2
+	CONFIG_STM32_TIM3_FULL_REMAP
+	CONFIG_STM32_TIM3_PARTIAL_REMAP
+	CONFIG_STM32_TIM4_REMAP
+	CONFIG_STM32_USART1_REMAP
+	CONFIG_STM32_USART2_REMAP
+	CONFIG_STM32_USART3_FULL_REMAP
+	CONFIG_STM32_USART3_PARTIAL_REMAP
+	CONFIG_STM32_SPI1_REMAP
+	CONFIG_STM32_SPI3_REMAP
+	CONFIG_STM32_I2C1_REMAP
+	CONFIG_STM32_CAN1_FULL_REMAP
+	CONFIG_STM32_CAN1_PARTIAL_REMAP
+	CONFIG_STM32_CAN2_REMAP
+
+  STM32F103V specific device driver settings
+
+	CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
+           m (m=4,5) for the console and ttys0 (default is the USART1).
+           
+           Note: USART1 is connected to a PL2303 serial to USB converter.
+           So USART1 is available through USB port labeled CN3 on the board.
+           
+	CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
+	   This specific the size of the receive buffer
+	CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
+	   being sent.  This specific the size of the transmit buffer
+	CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART.  Must be
+	CONFIG_U[S]ARTn_BITS - The number of bits.  Must be either 7 or 8.
+	CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+	CONFIG_U[S]ARTn_2STOP - Two stop bits
+
+	CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
+	  support. Non-interrupt-driven, poll-waiting is recommended if the
+	  interrupt rate would be to high in the interrupt driven case.
+	CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
+	  Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
+
+	CONFIG_SDIO_DMA - Support DMA data transfers.  Requires CONFIG_STM32_SDIO
+	  and CONFIG_STM32_DMA2.
+	CONFIG_SDIO_PRI - Select SDIO interrupt prority.  Default: 128
+	CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority. 
+	  Default:  Medium
+	CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode.  Default:
+	  4-bit transfer mode.
+    CONFIG_MMCSD_HAVECARDDETECT - Select if SDIO driver card detection
+      is 100% accurate  (it is on the  HY-MiniSTM32V)
+    
+    
+  HY-MiniSTM32V LCD Hardware Configuration  (SSD1289 controler)
+
+    CONFIG_NX_LCDDRIVER - To be defined to include LCD driver
+    CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
+      support. In this orientation, the HY-MiniSTM32V's
+      LCD used connector is at the right of the display.
+      Default is this 320x240 "landscape" orientation
+    CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
+      orientation support.  In this orientation, the HY-MiniSTM32V's
+      LCD used connector is at the bottom of the display. Default is
+      320x240 "landscape" orientation.
+    CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
+      portrait" orientation support.  In this orientation, the
+      HY-MiniSTM32V's LCD used connector is at the top of the display.
+      Default is 320x240 "landscape" orientation.
+    CONFIG_LCD_BACKLIGHT - Define to support an adjustable backlight
+      using timer 3.  The granularity of the settings is determined
+      by CONFIG_LCD_MAXPOWER.  Requires CONFIG_STM32_TIM3.
+    
+
+Configurations
+==============
+
+Each HY-MiniSTM32V configuration is maintained in a sudirectory and
+can be selected as follow:
+
+	cd tools
+	./configure.sh hymini-stm32v/<subdir>
+	cd -
+	. ./setenv.sh
+
+Where <subdir> is one of the following:
+
+  buttons:
+  --------
+
+    Uses apps/examples/buttons to exercise HY-MiniSTM32V buttons and
+    button interrupts.
+ 
+    CONFIG_STM32_CODESOURCERYL=y  : CodeSourcery under Linux
+
+  nsh and nsh2:
+  ------------
+    Configure the NuttShell (nsh) located at examples/nsh.
+
+    Differences between the two NSH configurations:
+
+    =========== ======================= ================================
+                nsh                     nsh2
+    =========== ======================= ================================
+    Toolchain:  Codesourcery for Linux  Codesourcery for Linux (1)
+    ----------- ----------------------- --------------------------------
+    Loader:     ST bootloader           ST bootloader
+    ----------- ----------------------- --------------------------------
+    Serial      Debug output: USART1    Debug output: USART1
+    Console:    NSH output:   USART1    NSH output:   USART1 (3)
+    ----------- ----------------------- --------------------------------
+    microSD     Yes                     Yes
+    Support
+    ----------- ----------------------- --------------------------------
+    FAT FS      CONFIG_FAT_LCNAME=y     CONFIG_FAT_LCNAME=y
+    Config      CONFIG_FAT_LFN=n        CONFIG_FAT_LFN=y (4)
+    ----------- ----------------------- --------------------------------
+	LCD Driver  No                      Yes
+	Support 
+    ----------- ----------------------- --------------------------------
+	RTC Support No                      Yes
+    ----------- ----------------------- --------------------------------
+    Support for No                      Yes
+    Built-in
+    Apps
+    ----------- ----------------------- --------------------------------
+    Built-in    None                    apps/examples/nx
+    Apps                                apps/examples/nxhello
+                                        apps/examples/usbstorage (5)
+                                        apps/examples/buttons
+                                        apps/examples/nximage
+    =========== ======================= ================================
+
+    (1) You will probably need to modify nsh/setenv.sh or nsh2/setenv.sh
+        to set up the correct PATH variable for whichever toolchain you
+        may use.
+    (2) Since DfuSe is assumed, this configuration may only work under
+        Cygwin without modification.
+    (3) When any other device other than /dev/console is used for a user
+        interface, (1) linefeeds (\n) will not be expanded to carriage return
+        / linefeeds \r\n). You will need to configure your terminal program
+        to account for this. And (2) input is not automatically echoed so
+        you will have to turn local echo on.
+    (4) Microsoft holds several patents related to the design of
+        long file names in the FAT file system.  Please refer to the
+        details in the top-level COPYING file.  Please do not use FAT
+        long file name unless you are familiar with these patent issues.
+    (5) When built as an NSH add-on command (CONFIG_EXAMPLES_USBSTRG_BUILTIN=y),
+        Caution should be used to assure that the SD drive is not in use when
+        the USB storage device is configured.  Specifically, the SD driver
+        should be unmounted like:
+
+        nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Card is mounted in NSH
+        ...
+        nsh> umount /mnd/sdcard                    # Unmount before connecting USB!!!
+        nsh> msconn                                # Connect the USB storage device
+        ...
+        nsh> msdis                                 # Disconnect USB storate device
+        nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Restore the mount
+
+        Failure to do this could result in corruption of the SD card format.
+
+  nx:
+  ---
+    An example using the NuttX graphics system (NX).  This example
+    focuses on general window controls, movement, mouse and keyboard
+    input.
+
+    CONFIG_STM32_CODESOURCERYW=y  : CodeSourcery under Windows
+    CONFIG_LCD_RPORTRAIT=y        : 240x320 reverse portrait
+
+  nxlines:
+  ------
+    Another example using the NuttX graphics system (NX).   This
+    example focuses on placing lines on the background in various
+    orientations.
+
+    CONFIG_STM32_CODESOURCERYL=y  : CodeSourcery under Linux
+    CONFIG_LCD_RPORTRAIT=y        : 240x320 reverse portrait
+
+  usbserial:
+  ---------
+    This configuration directory exercises the USB serial class
+    driver at examples/usbserial.  See examples/README.txt for
+    more information.
+
+    CONFIG_STM32_CODESOURCERYL=y  : CodeSourcery under Linux
+    
+    USB debug output can be enabled as by changing the following
+    settings in the configuration file:
+
+    -CONFIG_DEBUG=n
+    -CONFIG_DEBUG_VERBOSE=n
+    -CONFIG_DEBUG_USB=n
+    +CONFIG_DEBUG=y
+    +CONFIG_DEBUG_VERBOSE=y
+    +CONFIG_DEBUG_USB=y
+
+    -CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+    -CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+    -CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+    -CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+    -CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+    +CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=y
+    +CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=y
+    +CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=y
+    +CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=y
+    +CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=y
+
+    By default, the usbserial example uses the Prolific PL2303
+    serial/USB converter emulation.  The example can be modified
+    to use the CDC/ACM serial class by making the following changes
+    to the configuration file:
+
+    -CONFIG_USBSER=y
+    +CONFIG_USBSER=n
+
+    -CONFIG_CDCSER=n
+    +CONFIG_CDCSER=y
+
+    The example can also be converted to use the alternative
+    USB serial example at apps/examples/usbterm by changing the 
+    following:
+
+    -CONFIGURED_APPS += examples/usbserial
+    +CONFIGURED_APPS += examples/usbterm
+
+    In either the original appconfig file (before configuring)
+    or in the final apps/.config file (after configuring).
+
+  usbstorage:
+  ----------
+    This configuration directory exercises the USB mass storage
+    class driver at examples/usbstorage.  See examples/README.txt for
+    more information.
+
+    CONFIG_STM32_CODESOURCERYL=y  : CodeSourcery under Linux
+
diff --git a/nuttx/configs/hymini-stm32v/buttons/Make.defs b/nuttx/configs/hymini-stm32v/buttons/Make.defs
new file mode 100644
index 000000000..7bef1d228
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/buttons/Make.defs
@@ -0,0 +1,174 @@
+############################################################################
+# configs/hymini-stm32v/buttons/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_DFU),y)
+  LDSCRIPT = ld.script.dfu
+else
+  LDSCRIPT = ld.script
+endif
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/buttons/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/buttons/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/hymini-stm32v/buttons/appconfig b/nuttx/configs/hymini-stm32v/buttons/appconfig
new file mode 100644
index 000000000..b20cea202
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/buttons/appconfig
@@ -0,0 +1,39 @@
+############################################################################
+# configs/hymini-stm32v/buttons/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/buttons
+
diff --git a/nuttx/configs/hymini-stm32v/buttons/defconfig b/nuttx/configs/hymini-stm32v/buttons/defconfig
new file mode 100644
index 000000000..ccfff5a11
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/buttons/defconfig
@@ -0,0 +1,880 @@
+############################################################################
+# configs/hymini-stm32v/buttons/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_IRQBUTTONS - Must be defined for interrupting button support
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+#   CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM3=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F103VCT6=y
+CONFIG_ARCH_BOARD=hymini-stm32v
+CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+CONFIG_BOARD_LOOPSPERMSEC=5483
+CONFIG_DRAM_SIZE=0x0000C000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=y
+CONFIG_ARCH_IRQBUTTONS=y
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=y
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+CONFIG_STM32_DFU=n
+
+#
+#  Individual subsystems can be enabled:
+#
+# Individual subsystems can be enabled:
+# AHB: 
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=n
+CONFIG_STM32_CRC=n
+CONFIG_STM32_FSMC=y
+CONFIG_STM32_SDIO=n
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI4=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=n
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_USB=y
+CONFIG_STM32_CAN=n
+CONFIG_STM32_BKP=n
+CONFIG_STM32_PWR=n
+CONFIG_STM32_DAC=n
+# APB2:
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_SPI1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=y
+CONFIG_STM32_ADC3=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F103Z specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART2_SERIAL_CONSOLE=n
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=256
+CONFIG_USART2_TXBUFSIZE=256
+CONFIG_USART3_TXBUFSIZE=256
+CONFIG_USART4_TXBUFSIZE=256
+CONFIG_USART5_TXBUFSIZE=256
+
+CONFIG_USART1_RXBUFSIZE=256
+CONFIG_USART2_RXBUFSIZE=256
+CONFIG_USART3_RXBUFSIZE=256
+CONFIG_USART4_RXBUFSIZE=256
+CONFIG_USART5_RXBUFSIZE=256
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F103Z specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=y
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=y
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=n
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_MM_REGIONS=1
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2011
+CONFIG_START_MONTH=7
+CONFIG_START_DAY=7
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=y
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_NXFLAT=n
+CONFIG_SCHED_WORKQUEUE=n
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=y
+CONFIG_DISABLE_PTHREAD=y
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=y
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_DISABLE_ENVIRON=y
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=8
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=6
+CONFIG_NFILE_STREAMS=6
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=64
+CONFIG_STDIO_LINEBUFFER=y
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=n
+CONFIG_FAT_LCNAMES=n
+CONFIG_FAT_LFN=n
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=1
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=n
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=0
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=420
+CONFIG_NET_TCP=n
+CONFIG_NET_TCP_CONNS=40
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=n
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=n
+CONFIG_NET_ICMP_PING=n
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=n
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=n
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Settings for examples/uip
+#
+CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_UIP_DHCPC=n
+
+#
+# Settings for examples/nettest
+CONFIG_EXAMPLE_NETTEST_SERVER=n
+CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
+CONFIG_EXAMPLE_NETTEST_NOMAC=n
+CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
+
+#
+# Settings for examples/buttons
+#
+# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX
+#   Lowest and highest button number (0-7)
+# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX
+#   Lowest and highest interrupting button number (-7)
+# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n
+#
+CONFIG_EXAMPLE_BUTTONS_MIN=0
+CONFIG_EXAMPLE_BUTTONS_MAX=7
+CONFIG_EXAMPLE_IRQBUTTONS_MIN=2
+CONFIG_EXAMPLE_IRQBUTTONS_MAX=7
+CONFIG_EXAMPLE_BUTTONS_NAME0="WAKEUP"
+CONFIG_EXAMPLE_BUTTONS_NAME1="TAMPER"
+CONFIG_EXAMPLE_BUTTONS_NAME2="KEY"
+CONFIG_EXAMPLE_BUTTONS_NAME3="SELECT"
+CONFIG_EXAMPLE_BUTTONS_NAME4="DOWN"
+CONFIG_EXAMPLE_BUTTONS_NAME5="LEFT"
+CONFIG_EXAMPLE_BUTTONS_NAME6="RIGHT"
+CONFIG_EXAMPLE_BUTTONS_NAME7="UP"
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=n
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=n
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the Hy-Mini STM32v which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/hymini-stm32v/buttons/ld.script b/nuttx/configs/hymini-stm32v/buttons/ld.script
new file mode 100644
index 000000000..ef6968958
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/buttons/ld.script
@@ -0,0 +1,112 @@
+/****************************************************************************
+ * configs/hymini-stm32v/buttons/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
+ * 48Kb of SRAM beginning at address 0x2000:0000.  When booting from FLASH,
+ * FLASH memory is aliased to address 0x0000:0000 where the code expects to
+ * begin execution by jumping to the entry point in the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103V has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/buttons/ld.script.dfu b/nuttx/configs/hymini-stm32v/buttons/ld.script.dfu
new file mode 100644
index 000000000..5c839a0d8
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/buttons/ld.script.dfu
@@ -0,0 +1,111 @@
+/****************************************************************************
+ * configs/hymini-stm32v/buttons/ld.script.dfu
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  Here we assume that the
+ * Hy-Mini STM32v's DFU bootloader is being used.  In that case, the corrct
+ * load .text load address is 0x08003000 (leaving 464Kb).
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/buttons/setenv.sh b/nuttx/configs/hymini-stm32v/buttons/setenv.sh
new file mode 100755
index 000000000..df0dba318
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/buttons/setenv.sh
@@ -0,0 +1,47 @@
+#!/bin/bash
+# configs/hymini-stm32v/buttons/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$(basename $0)" = "setenv.sh" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
+
+WD=`pwd`
+export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
+export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
+export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/hymini-stm32v/include/README.txt b/nuttx/configs/hymini-stm32v/include/README.txt
new file mode 100755
index 000000000..ab0848412
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/include/README.txt
@@ -0,0 +1 @@
+This directory contains header files unique to the HY-MiniSTM32V development board.
diff --git a/nuttx/configs/hymini-stm32v/include/board.h b/nuttx/configs/hymini-stm32v/include/board.h
new file mode 100755
index 000000000..fbecc0b6c
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/include/board.h
@@ -0,0 +1,230 @@
+/************************************************************************************
+ * configs/hymini-stm32v/include/board.h
+ * include/arch/board/board.h
+ *
+ *   Copyright (C) 2011 Laurent Latil. All rights reserved.
+ *   Author: Laurent Latil <laurent@latil.nom.fr>
+ *
+ * Derives, in part, from configs/stm3210e-eval/include/board.h
+ *
+ *   Copyright (C) 2009 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+#ifndef __ARCH_BOARD_BOARD_H
+#define __ARCH_BOARD_BOARD_H
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+#ifndef __ASSEMBLY__
+# include <stdint.h>
+#endif
+#include "stm32_rcc.h"
+#include "stm32_sdio.h"
+#include "stm32_internal.h"
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/* Clocking *************************************************************************/
+
+/* On-board crystal frequency is 8MHz (HSE) */
+
+#define STM32_BOARD_XTAL        8000000ul
+
+/* PLL source is HSE/1, PLL multipler is 9: PLL frequency is 8MHz (XTAL) x 9 = 72MHz */
+
+#define STM32_CFGR_PLLSRC       RCC_CFGR_PLLSRC
+#define STM32_CFGR_PLLXTPRE     0
+#define STM32_CFGR_PLLMUL       RCC_CFGR_PLLMUL_CLKx9
+#define STM32_PLL_FREQUENCY     (9*STM32_BOARD_XTAL)
+
+/* Use the PLL and set the SYSCLK source to be the PLL */
+
+#define STM32_SYSCLK_SW         RCC_CFGR_SW_PLL
+#define STM32_SYSCLK_SWS        RCC_CFGR_SWS_PLL
+#define STM32_SYSCLK_FREQUENCY  STM32_PLL_FREQUENCY
+
+/* AHB clock (HCLK) is SYSCLK (72MHz) */
+
+#define STM32_RCC_CFGR_HPRE     RCC_CFGR_HPRE_SYSCLK
+#define STM32_HCLK_FREQUENCY    STM32_PLL_FREQUENCY
+#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY    /* same as above, to satisfy compiler */
+
+/* APB2 clock (PCLK2) is HCLK (72MHz) */
+
+#define STM32_RCC_CFGR_PPRE2    RCC_CFGR_PPRE2_HCLK
+#define STM32_PCLK2_FREQUENCY   STM32_HCLK_FREQUENCY
+
+/* APB1 clock (PCLK1) is HCLK/2 (36MHz) */
+
+#define STM32_RCC_CFGR_PPRE1    RCC_CFGR_PPRE1_HCLKd2
+#define STM32_PCLK1_FREQUENCY   (STM32_HCLK_FREQUENCY/2)
+
+/* USB divider -- Divide PLL clock by 1.5 */
+
+#define STM32_CFGR_USBPRE       0
+
+/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
+ * otherwise frequency is 2xAPBx. 
+ * Note: TIM1,8 are on APB2, others on APB1 */
+
+#define STM32_TIM18_FREQUENCY   STM32_HCLK_FREQUENCY
+#define STM32_TIM27_FREQUENCY   STM32_HCLK_FREQUENCY
+
+/* SDIO dividers.  Note that slower clocking is required when DMA is disabled 
+ * in order to avoid RX overrun/TX underrun errors due to delayed responses
+ * to service FIFOs in interrupt driven mode.  These values have not been
+ * tuned!!!
+ *
+ * HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz
+ */
+  
+#define SDIO_INIT_CLKDIV        (178 << SDIO_CLKCR_CLKDIV_SHIFT)
+
+/* DMA ON:  HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz
+ * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
+ */
+
+#ifdef CONFIG_SDIO_DMA
+#  define SDIO_MMCXFR_CLKDIV    (2 << SDIO_CLKCR_CLKDIV_SHIFT) 
+#else
+#  define SDIO_MMCXFR_CLKDIV    (3 << SDIO_CLKCR_CLKDIV_SHIFT) 
+#endif
+
+/* DMA ON:  HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz
+ * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
+ */
+
+#ifdef CONFIG_SDIO_DMA
+#  define SDIO_SDXFR_CLKDIV     (1 << SDIO_CLKCR_CLKDIV_SHIFT)
+#else
+#  define SDIO_SDXFR_CLKDIV     (3 << SDIO_CLKCR_CLKDIV_SHIFT)
+#endif
+
+/* LED definitions ******************************************************************/
+
+/* The board has 2 LEDs that we will encode as: */
+#define LED_STARTED       0  /* No LEDs */
+#define LED_HEAPALLOCATE  1  /* LED1 on */
+#define LED_IRQSENABLED   2  /* LED2 on */
+#define LED_STACKCREATED  3  /* LED1 on */
+#define LED_INIRQ         4  /* LED1 off */
+#define LED_SIGNAL        5  /* LED2 on */
+#define LED_ASSERTION     6  /* LED1 + LED2 */
+#define LED_PANIC         7  /* LED1 / LED2 blinking */
+
+/* The board supports two user buttons
+ *
+ * KeyA            -- Connected to PC.13
+ * KeyB            -- Connected to PB.2
+ */
+
+#define BUTTON_KEYA      0
+#define BUTTON_KEYB      1
+
+#define NUM_BUTTONS      2
+
+#define BUTTON_KEYA_BIT  (1 << BUTTON_KEYA)
+#define BUTTON_KEYB_BIT  (1 << BUTTON_KEYB)
+
+
+/************************************************************************************
+ * Public Data
+ ************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+#undef EXTERN
+#if defined(__cplusplus)
+#define EXTERN extern "C"
+extern "C" {
+#else
+#define EXTERN extern
+#endif
+
+/************************************************************************************
+ * Public Function Prototypes
+ ************************************************************************************/
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the initialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+
+EXTERN void stm32_boardinitialize(void);
+
+/************************************************************************************
+ * Button support.
+ *
+ * Description:
+ *   up_buttoninit() must be called to initialize button resources.  After
+ *   that, up_buttons() may be called to collect the current state of all
+ *   buttons or up_irqbutton() may be called to register button interrupt
+ *   handlers.
+ *
+ *   After up_buttoninit() has been called, up_buttons() may be called to
+ *   collect the state of all buttons.  up_buttons() returns an 8-bit bit set
+ *   with each bit associated with a button.  See the BUTTON_*_BIT and JOYSTICK_*_BIT
+ *   definitions in board.h for the meaning of each bit.
+ *
+ *   up_irqbutton() may be called to register an interrupt handler that will
+ *   be called when a button is depressed or released.  The ID value is a
+ *   button enumeration value that uniquely identifies a button resource. See the
+ *   BUTTON_* and JOYSTICK_* definitions in board.h for the meaning of enumeration
+ *   value.  The previous interrupt handler address is returned (so that it may
+ *   restored, if so desired).
+ *
+ ************************************************************************************/
+
+#ifdef CONFIG_ARCH_BUTTONS
+EXTERN void up_buttoninit(void);
+EXTERN uint8_t up_buttons(void);
+#ifdef CONFIG_ARCH_IRQBUTTONS
+EXTERN xcpt_t up_irqbutton(int id, xcpt_t irqhandler);
+#endif
+#endif
+
+#undef EXTERN
+#if defined(__cplusplus)
+}
+#endif
+
+#endif /* __ASSEMBLY__ */
+#endif  /* __ARCH_BOARD_BOARD_H */
diff --git a/nuttx/configs/hymini-stm32v/nsh/Make.defs b/nuttx/configs/hymini-stm32v/nsh/Make.defs
new file mode 100644
index 000000000..9b6c0b426
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh/Make.defs
@@ -0,0 +1,174 @@
+############################################################################
+# configs/hymini-stm32v/nsh/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_DFU),y)
+  LDSCRIPT = ld.script.dfu
+else
+  LDSCRIPT = ld.script
+endif
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/hymini-stm32v/nsh/appconfig b/nuttx/configs/hymini-stm32v/nsh/appconfig
new file mode 100644
index 000000000..785f83bd8
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh/appconfig
@@ -0,0 +1,41 @@
+############################################################################
+# configs/hymini-stm32v/nsh/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/nsh
+
+CONFIGURED_APPS += nshlib
+
diff --git a/nuttx/configs/hymini-stm32v/nsh/defconfig b/nuttx/configs/hymini-stm32v/nsh/defconfig
new file mode 100755
index 000000000..999cacfa4
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh/defconfig
@@ -0,0 +1,865 @@
+############################################################################
+# configs/hymini-stm32v/nsh/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+#   CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM3=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F103VCT6=y
+CONFIG_ARCH_BOARD=hymini-stm32v
+CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+CONFIG_BOARD_LOOPSPERMSEC=5483
+CONFIG_DRAM_SIZE=0x0000C000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=n
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=y
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+CONFIG_STM32_DFU=n
+
+#
+# Individual subsystems can be enabled:
+# AHB: 
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=y
+CONFIG_STM32_CRC=n
+CONFIG_STM32_FSMC=n
+CONFIG_STM32_SDIO=y
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI4=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=n
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_USB=y
+CONFIG_STM32_CAN=n
+CONFIG_STM32_BKP=n
+CONFIG_STM32_PWR=n
+CONFIG_STM32_DAC=n
+# APB2:
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_SPI1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=y
+CONFIG_STM32_ADC3=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F103V specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART2_SERIAL_CONSOLE=n
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=256
+CONFIG_USART2_TXBUFSIZE=256
+CONFIG_USART3_TXBUFSIZE=256
+CONFIG_USART4_TXBUFSIZE=256
+CONFIG_USART5_TXBUFSIZE=256
+
+CONFIG_USART1_RXBUFSIZE=256
+CONFIG_USART2_RXBUFSIZE=256
+CONFIG_USART3_RXBUFSIZE=256
+CONFIG_USART4_RXBUFSIZE=256
+CONFIG_USART5_RXBUFSIZE=256
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F103V specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=n
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=n
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=y
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_MM_REGIONS=1
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2009
+CONFIG_START_MONTH=9
+CONFIG_START_DAY=21
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=n
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_NXFLAT=n
+CONFIG_SCHED_WORKQUEUE=y
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=n
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=n
+CONFIG_DISABLE_ENVIRON=n
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=y
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=n
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=1
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# STM32 SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA - Support DMA data transfers.  Requires CONFIG_STM32_SDIO
+#   and CONFIG_STM32_DMA2.
+# CONFIG_SDIO_PRI - Select SDIO interrupt prority.  Default: 128
+# CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority. 
+#   Default:  Medium
+# CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode.  Default:
+#   4-bit transfer mode.
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=y
+#CONFIG_SDIO_PRI=128
+#CONFIG_SDIO_DMAPRIO
+#CONFIG_SDIO_WIDTH_D1_ONLY
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=0
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=420
+CONFIG_NET_TCP=n
+CONFIG_NET_TCP_CONNS=40
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=n
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=n
+CONFIG_NET_ICMP_PING=n
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=n
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=n
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Settings for examples/uip
+#
+CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_UIP_DHCPC=n
+
+#
+# Settings for examples/nettest
+CONFIG_EXAMPLE_NETTEST_SERVER=n
+CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
+CONFIG_EXAMPLE_NETTEST_NOMAC=n
+CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_BUILTIN_APPS - Support external registered,
+#   "named" applications that can be executed from the NSH
+#   command line (see apps/README.txt for more information).
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_BUILTIN_APPS=n
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=n
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the Hy-Mini STM32v which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/hymini-stm32v/nsh/ld.script b/nuttx/configs/hymini-stm32v/nsh/ld.script
new file mode 100755
index 000000000..c09e716cb
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh/ld.script
@@ -0,0 +1,112 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nsh/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  When booting from FLASH,
+ * FLASH memory is aliased to address 0x0000:0000 where the code expects to
+ * begin execution by jumping to the entry point in the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 512K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nsh/ld.script.dfu b/nuttx/configs/hymini-stm32v/nsh/ld.script.dfu
new file mode 100755
index 000000000..5dfc51ad1
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh/ld.script.dfu
@@ -0,0 +1,111 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nsh/ld.script.dfu
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  Here we assume that the
+ * Hy-Mini STM32v's DFU bootloader is being used.  In that case, the corrct
+ * load .text load address is 0x08003000 (leaving 464Kb).
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nsh/setenv.sh b/nuttx/configs/hymini-stm32v/nsh/setenv.sh
new file mode 100755
index 000000000..a0371cdce
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh/setenv.sh
@@ -0,0 +1,47 @@
+#!/bin/bash
+# configs/hymini-stm32v/dfu/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$(basename $0)" = "setenv.sh" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
+
+WD=`pwd`
+export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
+export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
+export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/hymini-stm32v/nsh2/Make.defs b/nuttx/configs/hymini-stm32v/nsh2/Make.defs
new file mode 100644
index 000000000..63c6317ef
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh2/Make.defs
@@ -0,0 +1,174 @@
+############################################################################
+# configs/hymini-stm32v/nsh2/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_DFU),y)
+  LDSCRIPT = ld.script.dfu
+else
+  LDSCRIPT = ld.script
+endif
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/hymini-stm32v/nsh2/appconfig b/nuttx/configs/hymini-stm32v/nsh2/appconfig
new file mode 100644
index 000000000..4e44cf6a3
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh2/appconfig
@@ -0,0 +1,52 @@
+############################################################################
+# configs/hymini-stm32v/nsh2/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/nsh
+
+# The NSH application library
+
+CONFIGURED_APPS += nshlib
+
+# The NX and NXHELLO examples configured as an NX built-in commands
+
+# CONFIGURED_APPS += examples/nx
+CONFIGURED_APPS += examples/usbstorage
+CONFIGURED_APPS += examples/nximage
+CONFIGURED_APPS += examples/touchscreen
+CONFIGURED_APPS += examples/lcdtest
+CONFIGURED_APPS += examples/buttons
+CONFIGURED_APPS += examples/tc_test
diff --git a/nuttx/configs/hymini-stm32v/nsh2/defconfig b/nuttx/configs/hymini-stm32v/nsh2/defconfig
new file mode 100644
index 000000000..240d77fc5
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh2/defconfig
@@ -0,0 +1,1209 @@
+############################################################################
+# configs/hymini-stm32v/nsh2/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+# CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM3=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F103VCT6=y
+CONFIG_ARCH_BOARD=hymini-stm32v
+CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+CONFIG_BOARD_LOOPSPERMSEC=5483
+CONFIG_DRAM_SIZE=0x0000C000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=y
+CONFIG_ARCH_IRQBUTTONS=y
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=y
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+CONFIG_STM32_DFU=n
+
+#
+# Individual subsystems can be enabled:
+# AHB: 
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=y
+CONFIG_STM32_CRC=n
+CONFIG_STM32_FSMC=y
+CONFIG_STM32_SDIO=y
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=y
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI4=n
+CONFIG_STM32_USART2=n
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=n
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_USB=y
+CONFIG_STM32_CAN=n
+
+# Backup domain
+CONFIG_STM32_BKP=y
+CONFIG_STM32_PWR=y
+CONFIG_STM32_DAC=n
+# APB2:
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_SPI1=y
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=y
+CONFIG_STM32_ADC3=n
+
+CONFIG_STM32_TIM3_PARTIAL_REMAP=y
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F103Z specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART2_SERIAL_CONSOLE=n
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=256
+CONFIG_USART2_TXBUFSIZE=256
+CONFIG_USART3_TXBUFSIZE=256
+CONFIG_USART4_TXBUFSIZE=256
+CONFIG_USART5_TXBUFSIZE=256
+
+CONFIG_USART1_RXBUFSIZE=256
+CONFIG_USART2_RXBUFSIZE=256
+CONFIG_USART3_RXBUFSIZE=256
+CONFIG_USART4_RXBUFSIZE=256
+CONFIG_USART5_RXBUFSIZE=256
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F103Z specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=n
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=n
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=y
+CONFIG_HAVE_LIBM=n
+
+CONFIG_RTC=y
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Specifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distant past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimal support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   descriptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+# CONFIG_SCHED_WAITPID - Enable the waitpid() API
+# CONFIG_SCHED_ATEXIT - Enabled the atexit() API
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=y
+CONFIG_DEBUG_VERBOSE=y
+CONFIG_DEBUG_GRAPHICS=y
+CONFIG_DEBUG_LCD=y
+CONFIG_DEBUG_INPUT=y
+CONFIG_DEBUG_USB=y
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_MM_REGIONS=1
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2011
+CONFIG_START_MONTH=7
+CONFIG_START_DAY=5
+CONFIG_GREGORIAN_TIME=y
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=n
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SCHED_WORKQUEUE=y
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+CONFIG_SCHED_WAITPID=y
+CONFIG_SCHED_ATEXIT=n
+
+#
+# Settings for NXFLAT
+#
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
+#  with.  CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
+#  CONFIG_DEBUG_BINFMT have to be defined or
+#  CONFIG_NXFLAT_DUMPBUFFER does nothing.
+# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
+#  is ordered by symbol name
+#
+CONFIG_NXFLAT=y
+CONFIG_NXFLAT_DUMPBUFFER=n
+CONFIG_SYMTAB_ORDEREDBYNAME=y
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=n
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=n
+CONFIG_DISABLE_ENVIRON=n
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Framebuffer driver options
+#
+CONFIG_FB_CMAP=n
+CONFIG_FB_HWCURSOR=n
+CONFIG_FB_HWCURSORIMAGE=n
+#CONFIG_FB_HWCURSORSIZE
+#CONFIG_FB_TRANSPARENCY
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=y
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=y
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=y
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# STM32 SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA - Support DMA data transfers.  Requires CONFIG_STM32_SDIO
+#   and CONFIG_STM32_DMA2.
+# CONFIG_SDIO_PRI - Select SDIO interrupt priority.  Default: 128
+# CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority. 
+#   Default:  Medium
+# CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode.  Default:
+#   4-bit transfer mode.
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=y
+#CONFIG_SDIO_PRI=128
+#CONFIG_SDIO_DMAPRIO
+#CONFIG_SDIO_WIDTH_D1_ONLY
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=y
+
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=y
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=y
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=y
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Graphics related configuration settings
+#
+# CONFIG_NX
+#   Enables overall support for graphics library and NX
+# CONFIG_NX_MULTIUSER
+#   Configures NX in multi-user mode
+# CONFIG_NX_NPLANES
+#   Some YUV color formats requires support for multiple planes,
+#   one for each color component.  Unless you have such special
+#   hardware, this value should be undefined or set to 1
+# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
+# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
+# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
+# CONFIG_NX_DISABLE_32BPP
+#   NX supports a variety of pixel depths.  You can save some
+#   memory by disabling support for unused color depths.
+# CONFIG_NX_PACKEDMSFIRST
+#   If a pixel depth of less than 8-bits is used, then NX needs
+#   to know if the pixels pack from the MS to LS or from LS to MS
+# CONFIG_NX_LCDDRIVER
+#   By default, NX builds to use a framebuffer driver (see
+#   include/nuttx/fb.h). If this option is defined, NX will
+#   build to use an LCD driver (see include/nuttx/lcd/lcd.h).
+# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
+# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
+# CONFIG_NX_MOUSE
+#   Build in support for mouse input
+# CONFIG_NX_KBD
+#   Build in support of keypad/keyboard input
+# CONFIG_NXTK_BORDERWIDTH
+#   Specifies with with of the border (in pixels) used with
+#   framed windows.  The default is 4.
+# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
+#   Specify the colors of the border used with framed windows.
+#   CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
+#   is normally darker.  The default is medium and dark grey,
+#   respectively
+# CONFIG_NXTK_AUTORAISE
+#   If set, a window will be raised to the top if the mouse position
+#   is over a visible portion of the window.  Default: A mouse
+#   button must be clicked over a visible portion of the window.
+# CONFIG_NXFONTS_CHARBITS
+#   The number of bits in the character set.  Current options are
+#   only 7 and 8.  The default is 7.
+# CONFIG_NXFONT_SANS23X27
+#   This option enables support for a tiny, 23x27 san serif font
+#   (font ID FONTID_SANS23X27 == 1).
+# CONFIG_NXFONT_SANS22X29
+#   This option enables support for a small, 22x29 san serif font
+#   (font ID FONTID_SANS22X29 == 2).
+# CONFIG_NXFONT_SANS28X37
+#   This option enables support for a medium, 28x37 san serif font
+#   (font ID FONTID_SANS28X37 == 3).
+# CONFIG_NXFONT_SANS39X48
+#   This option enables support for a large, 39x48 san serif font
+#   (font ID FONTID_SANS39X48 == 4).
+# CONFIG_NXFONT_SANS22X29B
+#   This option enables support for a small, 22x29 san serif bold font
+#   (font ID FONTID_SANS22X29B == 5).
+# CONFIG_NXFONT_SANS28X37B
+#   This option enables support for a medium, 28x37 san serif bold font
+#   (font ID FONTID_SANS28X37B == 6).
+# CONFIG_NXFONT_SANS40X49B
+#   This option enables support for a large, 40x49 san serif bold font
+#   (font ID FONTID_SANS40X49B == 7).
+# CONFIG_NXFONT_SERIF22X29
+#   This option enables support for a small, 22x29 font (with serifs)
+#   (font ID FONTID_SERIF22X29 == 8).
+# CONFIG_NXFONT_SERIF29X37
+#   This option enables support for a medium, 29x37 font (with serifs)
+#   (font ID FONTID_SERIF29X37 == 9).
+# CONFIG_NXFONT_SERIF38X48
+#   This option enables support for a large, 38x48 font (with serifs)
+#   (font ID FONTID_SERIF38X48 == 10).
+# CONFIG_NXFONT_SERIF22X28B
+#   This option enables support for a small, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF22X28B == 11).
+# CONFIG_NXFONT_SERIF27X38B
+#   This option enables support for a medium, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF27X38B == 12).
+# CONFIG_NXFONT_SERIF38X49B
+#   This option enables support for a large, 38x49 bold font (with serifs)
+#   (font ID FONTID_SERIF38X49B == 13).
+#
+# NX Multi-user only options:
+#
+# CONFIG_NX_BLOCKING
+#   Open the client message queues in blocking mode.  In this case,
+#   nx_eventhandler()  will not return until a message is received and processed.
+# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
+#   Specifies the maximum number of messages that can fit in
+#   the message queues.  No additional resources are allocated, but
+#   this can be set to prevent flooding of the client or server with
+#   too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
+#   messages are pre-allocated).
+#
+CONFIG_NX=y
+CONFIG_NX_MULTIUSER=n
+CONFIG_NX_NPLANES=1
+CONFIG_NX_DISABLE_1BPP=y
+CONFIG_NX_DISABLE_2BPP=y
+CONFIG_NX_DISABLE_4BPP=y
+CONFIG_NX_DISABLE_8BPP=y
+CONFIG_NX_DISABLE_16BPP=n
+CONFIG_NX_DISABLE_24BPP=y
+CONFIG_NX_DISABLE_32BPP=y
+CONFIG_NX_PACKEDMSFIRST=n
+CONFIG_NX_LCDDRIVER=y
+
+CONFIG_NX_MOUSE=y
+CONFIG_NX_KBD=n
+
+#CONFIG_NXTK_BORDERWIDTH=4
+CONFIG_NXTK_BORDERCOLOR1=0xd69a
+CONFIG_NXTK_BORDERCOLOR2=0xad55
+CONFIG_NXTK_AUTORAISE=n
+CONFIG_NXFONT_SANS22X29=n
+CONFIG_NXFONT_SANS23X27=y
+CONFIG_NXFONT_SANS28X37=n
+CONFIG_NXFONT_SANS22X29B=n
+CONFIG_NXFONT_SANS28X37B=y
+CONFIG_NXFONT_SANS40X49B=n
+CONFIG_NXFONT_SERIF22X29=n
+CONFIG_NXFONT_SERIF29X37=n
+CONFIG_NXFONT_SERIF38X48=n
+CONFIG_NXFONT_SERIF22X28B=n
+CONFIG_NXFONT_SERIF27X38B=n
+CONFIG_NXFONT_SERIF38X49B=n
+CONFIG_NXFONTS_CHARBITS=7
+CONFIG_NX_BLOCKING=y
+CONFIG_NX_MXSERVERMSGS=32
+CONFIG_NX_MXCLIENTMSGS=16
+
+#
+# LCD Hardware Configuration
+#
+# CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
+#   support. In this orientation, the HY-MiniSTM32 screen
+#   has the used connector at the right of display.
+# CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
+#   orientation support.  In this orientation, the HY-MiniSTM32 screen
+#   has the used connector at bottom of display.
+# CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
+#   portrait" orientation support.  In this orientation, the HY-MiniSTM32
+#   screen has the used connector at top of display.
+# CONFIG_LCD_BACKLIGHT - Define to support an adjustable backlight
+#   using timer 3.  The granularity of the settings is determined
+#   by CONFIG_LCD_MAXPOWER.  Requires CONFIG_STM32_TIM3.
+#
+CONFIG_LCD_LANDSCAPE=n
+CONFIG_LCD_PORTRAIT=y
+CONFIG_LCD_RPORTRAIT=n
+CONFIG_LCD_BACKLIGHT=y
+
+# Configurable steps for the LCD backlight
+CONFIG_LCD_MAXPOWER=100
+
+# Not used
+CONFIG_LCD_MAXCONTRAST=100
+
+#
+# TouchScreen hardware
+#
+CONFIG_INPUT=y
+CONFIG_INPUT_ADS7843E=y
+CONFIG_SPI_OWNBUS=y
+CONFIG_ADS7843E_SPIDEV=1
+#CONFIG_ADS7843E_SPIMODE=SPIDEV_MODE0
+
+CONFIG_EXAMPLES_TOUCHSCREEN_BUILTIN=y
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_BUILTIN_APPS - Support external registered,
+#   "named" applications that can be executed from the NSH
+#   command line (see apps/README.txt for more information).
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_CONDEV - Select the serial device used to support
+#   the NSH console.  Default: stdin and stdout
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=y
+CONFIG_NSH_CONSOLE=y
+#CONFIG_NSH_CONDEV="/dev/ttyS1"
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=n
+
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Settings for examples/nx
+#
+# CONFIG_EXAMPLES_NX_BUILTIN -- Build the NX example as a "built-in"
+#  that can be executed from the NSH command line  
+# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NX_DEVNO - The LCD device to select from the LCD
+#  driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background.  Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_FONTID - Selects the font (see font ID numbers in
+#   include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 32.
+# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows;  Default is to
+#   use pretty, framed NXTK windows with toolbars.
+# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating
+#   the NX server.  Default 2048
+# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority.  Default: 80
+# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority.  Default: 120
+# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with
+#   nx_eventnotify().  Default: 4
+#
+CONFIG_EXAMPLES_NX_BUILTIN=y
+CONFIG_EXAMPLES_NX_VPLANE=0
+CONFIG_EXAMPLES_NX_DEVNO=0
+CONFIG_EXAMPLES_NX_BGCOLOR=0x0011
+CONFIG_EXAMPLES_NX_COLOR1=0xaedc
+CONFIG_EXAMPLES_NX_COLOR2=0xe7ff
+CONFIG_EXAMPLES_NX_TBCOLOR=0xd69a
+CONFIG_EXAMPLES_NX_FONTID=0
+CONFIG_EXAMPLES_NX_FONTCOLOR=0x0000
+CONFIG_EXAMPLES_NX_BPP=16
+CONFIG_EXAMPLES_NX_RAWWINDOWS=n
+CONFIG_EXAMPLES_NX_STACKSIZE=2048
+CONFIG_EXAMPLES_NX_CLIENTPRIO=80
+CONFIG_EXAMPLES_NX_SERVERPRIO=120
+CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
+CONFIG_EXAMPLES_NX_EXTERNINIT=n
+
+#
+# Settings for examples/nxhello
+#
+# CONFIG_EXAMPLES_NXHELLO_BUILTIN -- Build the NXHELLO example as a "built-in"
+#   that can be executed from the NSH command line    
+# CONFIG_EXAMPLES_NXHELLO_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXHELLO_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXHELLO_BGCOLOR -- The color of the background.  Default
+#   depends on CONFIG_EXAMPLES_NXHELLO_BPP.
+# CONFIG_EXAMPLES_NXHELLO_FONTID - Selects the font (see font ID numbers in
+#   include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NXHELLO_FONTCOLOR -- The color of the fonts used in the
+#   background window. Default depends on CONFIG_EXAMPLES_NXHELLO_BPP.
+# CONFIG_EXAMPLES_NXHELLO_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 32.
+# CONFIG_EXAMPLES_NXHELLO_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXHELLO_BUILTIN=y
+CONFIG_EXAMPLES_NXHELLO_VPLANE=0
+CONFIG_EXAMPLES_NXHELLO_DEVNO=0
+CONFIG_EXAMPLES_NXHELLO_BGCOLOR=0x0011
+CONFIG_EXAMPLES_NXHELLO_FONTID=6
+CONFIG_EXAMPLES_NXHELLO_FONTCOLOR=0xffdf
+CONFIG_EXAMPLES_NXHELLO_BPP=16
+CONFIG_EXAMPLES_NXHELLO_EXTERNINIT=n
+
+#
+# Settings for examples/nximage
+#
+# CONFIG_EXAMPLES_NXIMAGE_BUILTIN -- Build the NXIMAGE example as a "built-in"
+#   that can be executed from the NSH command line    
+# CONFIG_EXAMPLES_NXIMAGE_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_BPP -- Pixels per pixel to use.  Valid options
+#   include 8, 16, and 24.  Default is 16.
+# CONFIG_EXAMPLES_NXIMAGE_XSCALEp5, CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0 -- The logo image width is 160 columns.
+#   One of these may be defined to rescale the image horizontally by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_YSCALEp5, CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0 -- The logo image height is 160 rows.
+#   One of these may be defined to rescale the image vertically by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXIMAGE_BUILTIN=y
+CONFIG_EXAMPLES_NXIMAGE_VPLANE=0
+CONFIG_EXAMPLES_NXIMAGE_DEVNO=0
+CONFIG_EXAMPLES_NXIMAGE_BPP=16
+CONFIG_EXAMPLES_NXIMAGE_XSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT=n
+
+#
+# Settings for examples/nxlines
+#
+# CONFIG_EXAMPLES_NXLINES_BUILTIN -- Build the NXLINES example as a "built-in"
+#   that can be executed from the NSH command line
+# CONFIG_EXAMPLES_NXLINES_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXLINES_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXLINES_BGCOLOR -- The color of the background.  Default
+#   depends on CONFIG_EXAMPLES_NXLINES_BPP.
+# CONFIG_EXAMPLES_NXLINES_LINEWIDTH - Selects the width of the lines in
+#   pixels (default: 16)
+# CONFIG_EXAMPLES_NXLINES_LINECOLOR -- The color of the central lines drawn
+#   in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_BORDERWIDTH -- The width of the circular border
+#   drawn in the background window. (default: 4).
+# CONFIG_EXAMPLES_NXLINES_BORDERCOLOR -- The color of the circular border
+#   drawn in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR -- The color of the circular region
+#   filled in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 16.
+# CONFIG_EXAMPLES_NXLINES_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXLINES_BUILTIN=n
+CONFIG_EXAMPLES_NXLINES_VPLANE=0
+CONFIG_EXAMPLES_NXLINES_DEVNO=0
+CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
+CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
+CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
+CONFIG_EXAMPLES_NXLINES_BORDERWIDTH=4
+CONFIG_EXAMPLES_NXLINES_BORDERCOLOR=0xffe0
+CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR=0xf7bb
+CONFIG_EXAMPLES_NXLINES_BPP=16
+CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n
+
+#
+# Settings for examples/usbstorage
+#
+# CONFIG_EXAMPLES_USBSTRG_BUILTIN
+#   This example can be built as two NSH "built-in" commands if this option
+#   is selection: 'msconn' will connect the USB mass storage device; 'msdis'
+#   will disconnect the USB storage device.
+# CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    Defines the number of logical units (LUNs) exported by the USB storage
+#    driver.  Each LUN corresponds to one exported block driver (or partition
+#    of a block driver).  May be 1, 2, or 3.  Default is 1.
+# CONFIG_EXAMPLES_USBSTRG_DEVMINOR1
+#    The minor device number of the block driver for the first LUN. For
+#    example, N in /dev/mmcsdN.  Used for registering the block driver. Default
+#    is zero.
+# CONFIG_EXAMPLES_USBSTRG_DEVPATH1
+#    The full path to the registered block driver.  Default is "/dev/mmcsd0"
+#  CONFIG_EXAMPLES_USBSTRG_DEVMINOR2 and CONFIG_EXAMPLES_USBSTRG_DEVPATH2
+#    Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    is 2 or 3.  No defaults.
+#  CONFIG_EXAMPLES_USBSTRG_DEVMINOR3 and CONFIG_EXAMPLES_USBSTRG_DEVPATH3
+#    Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    is 3.  No defaults.
+#  CONFIG_EXAMPLES_USBSTRG_DEBUGMM
+#    Enables some debug tests to check for memory usage and memory leaks.
+#
+#  If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then
+#  the example code will also manage the USB trace output.  The amount of trace output
+#  can be controlled using:
+#
+#  CONFIG_EXAMPLES_USBSTRG_TRACEINIT
+#    Show initialization events
+#  CONFIG_EXAMPLES_USBSTRG_TRACECLASS
+#    Show class driver events
+#  CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS
+#    Show data transfer events
+#  CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER
+#    Show controller events
+#  CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS
+#    Show interrupt-related events.
+#
+CONFIG_EXAMPLES_USBSTRG_BUILTIN=y
+CONFIG_EXAMPLES_USBSTRG_NLUNS=1
+CONFIG_EXAMPLES_USBSTRG_DEVMINOR1=0
+CONFIG_EXAMPLES_USBSTRG_DEVPATH1="/dev/mmcsd0"
+CONFIG_EXAMPLES_USBSTRG_DEBUGMM=n
+CONFIG_EXAMPLES_USBSTRG_TRACEINIT=n
+CONFIG_EXAMPLES_USBSTRG_TRACECLASS=n
+CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS=n
+
+
+CONFIG_EXAMPLES_LCDTEST_BUILTIN=y
+
+CONFIG_EXAMPLES_BUTTONS_BUILTIN=y
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the Hy-Mini STM32v which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/hymini-stm32v/nsh2/ld.script b/nuttx/configs/hymini-stm32v/nsh2/ld.script
new file mode 100644
index 000000000..1b861e6b6
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh2/ld.script
@@ -0,0 +1,112 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nsh2/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
+ * 48Kb of SRAM beginning at address 0x2000:0000.  When booting from FLASH,
+ * FLASH memory is aliased to address 0x0000:0000 where the code expects to
+ * begin execution by jumping to the entry point in the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nsh2/ld.script.dfu b/nuttx/configs/hymini-stm32v/nsh2/ld.script.dfu
new file mode 100644
index 000000000..a8d0839c1
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh2/ld.script.dfu
@@ -0,0 +1,111 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nsh2/ld.script.dfu
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  Here we assume that the
+ * Hy-Mini STM32v's DFU bootloader is being used.  In that case, the corrct
+ * load .text load address is 0x08003000 (leaving 464Kb).
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nsh2/setenv.sh b/nuttx/configs/hymini-stm32v/nsh2/setenv.sh
new file mode 100755
index 000000000..37ae1800b
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nsh2/setenv.sh
@@ -0,0 +1,67 @@
+#!/bin/bash
+# configs/hymini-stm32v/nsh2/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+# This the Cygwin path to the location where I installed the RIDE
+# toolchain under windows.  You will also have to edit this if you install
+# the RIDE toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Raisonance/Ride/arm-gcc/bin"
+
+# This the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+
+# This the Cygwin path to the location where I build the buildroot
+# toolchain.
+#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/hymini-stm32v/nx/Make.defs b/nuttx/configs/hymini-stm32v/nx/Make.defs
new file mode 100644
index 000000000..4edd1231f
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nx/Make.defs
@@ -0,0 +1,174 @@
+############################################################################
+# configs/hymini-stm32v/nx/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_DFU),y)
+  LDSCRIPT = ld.script.dfu
+else
+  LDSCRIPT = ld.script
+endif
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nx/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nx/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/hymini-stm32v/nx/appconfig b/nuttx/configs/hymini-stm32v/nx/appconfig
new file mode 100644
index 000000000..2a1978a7e
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nx/appconfig
@@ -0,0 +1,39 @@
+############################################################################
+# configs/hymini-stm32v/nx/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/nx
+
diff --git a/nuttx/configs/hymini-stm32v/nx/defconfig b/nuttx/configs/hymini-stm32v/nx/defconfig
new file mode 100644
index 000000000..a392b9461
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nx/defconfig
@@ -0,0 +1,1153 @@
+############################################################################
+# configs/hymini-stm32v/nx/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+# CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM3=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F103VCT6=y
+CONFIG_ARCH_BOARD=hymini-stm32v
+CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+CONFIG_BOARD_LOOPSPERMSEC=5483
+CONFIG_DRAM_SIZE=0x0000C000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=n
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=y
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+CONFIG_STM32_DFU=n
+
+#
+# Individual subsystems can be enabled:
+# AHB: 
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=y
+CONFIG_STM32_CRC=n
+CONFIG_STM32_FSMC=y
+CONFIG_STM32_SDIO=y
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI4=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=y
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_USB=y
+CONFIG_STM32_CAN=n
+CONFIG_STM32_BKP=n
+CONFIG_STM32_PWR=n
+CONFIG_STM32_DAC=n
+# APB2:
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_SPI1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=y
+CONFIG_STM32_ADC3=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F103V specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART2_SERIAL_CONSOLE=n
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=256
+CONFIG_USART2_TXBUFSIZE=256
+CONFIG_USART3_TXBUFSIZE=256
+CONFIG_USART4_TXBUFSIZE=256
+CONFIG_USART5_TXBUFSIZE=256
+
+CONFIG_USART1_RXBUFSIZE=256
+CONFIG_USART2_RXBUFSIZE=256
+CONFIG_USART3_RXBUFSIZE=256
+CONFIG_USART4_RXBUFSIZE=256
+CONFIG_USART5_RXBUFSIZE=256
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F103V specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=n
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=y
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=n
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_GRAPHICS=n
+CONFIG_DEBUG_LCD=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_MM_REGIONS=1
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2011
+CONFIG_START_MONTH=7
+CONFIG_START_DAY=5
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=n
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SCHED_WORKQUEUE=y
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+
+#
+# Settings for NXFLAT
+#
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
+#  with.  CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
+#  CONFIG_DEBUG_BINFMT have to be defined or
+#  CONFIG_NXFLAT_DUMPBUFFER does nothing.
+# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
+#  is ordered by symbol name
+#
+CONFIG_NXFLAT=n
+CONFIG_NXFLAT_DUMPBUFFER=n
+CONFIG_SYMTAB_ORDEREDBYNAME=y
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=y
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_DISABLE_ENVIRON=y
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Framebuffer driver options
+#
+CONFIG_FB_CMAP=n
+CONFIG_FB_HWCURSOR=n
+CONFIG_FB_HWCURSORIMAGE=n
+#CONFIG_FB_HWCURSORSIZE
+#CONFIG_FB_TRANSPARENCY
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=n
+CONFIG_FAT_LCNAMES=n
+CONFIG_FAT_LFN=n
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=1
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=y
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=0
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=420
+CONFIG_NET_TCP=n
+CONFIG_NET_TCP_CONNS=40
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=n
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=n
+CONFIG_NET_ICMP_PING=n
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=n
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=n
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Graphics related configuration settings
+#
+# CONFIG_NX
+#   Enables overall support for graphics library and NX
+# CONFIG_NX_MULTIUSER
+#   Configures NX in multi-user mode
+# CONFIG_NX_NPLANES
+#   Some YUV color formats requires support for multiple planes,
+#   one for each color component.  Unless you have such special
+#   hardware, this value should be undefined or set to 1
+# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
+# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
+# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
+# CONFIG_NX_DISABLE_32BPP
+#   NX supports a variety of pixel depths.  You can save some
+#   memory by disabling support for unused color depths.
+# CONFIG_NX_PACKEDMSFIRST
+#   If a pixel depth of less than 8-bits is used, then NX needs
+#   to know if the pixels pack from the MS to LS or from LS to MS
+# CONFIG_NX_LCDDRIVER
+#   By default, NX builds to use a framebuffer driver (see
+#   include/nuttx/fb.h). If this option is defined, NX will
+#   build to use an LCD driver (see include/nuttx/lcd/lcd.h).
+# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
+# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
+# CONFIG_NX_MOUSE
+#   Build in support for mouse input
+# CONFIG_NX_KBD
+#   Build in support of keypad/keyboard input
+# CONFIG_NXTK_BORDERWIDTH
+#   Specifies with with of the border (in pixels) used with
+#   framed windows.  The default is 4.
+# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
+#   Specify the colors of the border used with framed windows.
+#   CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
+#   is normally darker.  The default is medium and dark grey,
+#   respectively
+# CONFIG_NXTK_AUTORAISE
+#   If set, a window will be raised to the top if the mouse position
+#   is over a visible portion of the window.  Default: A mouse
+#   button must be clicked over a visible portion of the window.
+# CONFIG_NXFONTS_CHARBITS
+#   The number of bits in the character set.  Current options are
+#   only 7 and 8.  The default is 7.
+# CONFIG_NXFONT_SANS23X27
+#   This option enables support for a tiny, 23x27 san serif font
+#   (font ID FONTID_SANS23X27 == 1).
+# CONFIG_NXFONT_SANS22X29
+#   This option enables support for a small, 22x29 san serif font
+#   (font ID FONTID_SANS22X29 == 2).
+# CONFIG_NXFONT_SANS28X37
+#   This option enables support for a medium, 28x37 san serif font
+#   (font ID FONTID_SANS28X37 == 3).
+# CONFIG_NXFONT_SANS39X48
+#   This option enables support for a large, 39x48 san serif font
+#   (font ID FONTID_SANS39X48 == 4).
+# CONFIG_NXFONT_SANS22X29B
+#   This option enables support for a small, 22x29 san serif bold font
+#   (font ID FONTID_SANS22X29B == 5).
+# CONFIG_NXFONT_SANS28X37B
+#   This option enables support for a medium, 28x37 san serif bold font
+#   (font ID FONTID_SANS28X37B == 6).
+# CONFIG_NXFONT_SANS40X49B
+#   This option enables support for a large, 40x49 san serif bold font
+#   (font ID FONTID_SANS40X49B == 7).
+# CONFIG_NXFONT_SERIF22X29
+#   This option enables support for a small, 22x29 font (with serifs)
+#   (font ID FONTID_SERIF22X29 == 8).
+# CONFIG_NXFONT_SERIF29X37
+#   This option enables support for a medium, 29x37 font (with serifs)
+#   (font ID FONTID_SERIF29X37 == 9).
+# CONFIG_NXFONT_SERIF38X48
+#   This option enables support for a large, 38x48 font (with serifs)
+#   (font ID FONTID_SERIF38X48 == 10).
+# CONFIG_NXFONT_SERIF22X28B
+#   This option enables support for a small, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF22X28B == 11).
+# CONFIG_NXFONT_SERIF27X38B
+#   This option enables support for a medium, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF27X38B == 12).
+# CONFIG_NXFONT_SERIF38X49B
+#   This option enables support for a large, 38x49 bold font (with serifs)
+#   (font ID FONTID_SERIF38X49B == 13).
+#
+# NX Multi-user only options:
+#
+# CONFIG_NX_BLOCKING
+#   Open the client message queues in blocking mode.  In this case,
+#   nx_eventhandler()  will not return until a message is received and processed.
+# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
+#   Specifies the maximum number of messages that can fit in
+#   the message queues.  No additional resources are allocated, but
+#   this can be set to prevent flooding of the client or server with
+#   too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
+#   messages are pre-allocated).
+#
+CONFIG_NX=y
+CONFIG_NX_MULTIUSER=n
+CONFIG_NX_NPLANES=1
+CONFIG_NX_DISABLE_1BPP=y
+CONFIG_NX_DISABLE_2BPP=y
+CONFIG_NX_DISABLE_4BPP=y
+CONFIG_NX_DISABLE_8BPP=y
+CONFIG_NX_DISABLE_16BPP=n
+CONFIG_NX_DISABLE_24BPP=y
+CONFIG_NX_DISABLE_32BPP=y
+CONFIG_NX_PACKEDMSFIRST=n
+CONFIG_NX_LCDDRIVER=y
+CONFIG_LCD_MAXPOWER=1
+CONFIG_LCD_MAXCONTRAST=1
+CONFIG_NX_MOUSE=y
+CONFIG_NX_KBD=y
+#CONFIG_NXTK_BORDERWIDTH=4
+CONFIG_NXTK_BORDERCOLOR1=0xd69a
+CONFIG_NXTK_BORDERCOLOR2=0xad55
+CONFIG_NXTK_AUTORAISE=n
+CONFIG_NXFONT_SANS22X29=n
+CONFIG_NXFONT_SANS23X27=y
+CONFIG_NXFONT_SANS28X37=n
+CONFIG_NXFONT_SANS22X29B=n
+CONFIG_NXFONT_SANS28X37B=n
+CONFIG_NXFONT_SANS40X49B=n
+CONFIG_NXFONT_SERIF22X29=n
+CONFIG_NXFONT_SERIF29X37=n
+CONFIG_NXFONT_SERIF38X48=n
+CONFIG_NXFONT_SERIF22X28B=n
+CONFIG_NXFONT_SERIF27X38B=n
+CONFIG_NXFONT_SERIF38X49B=n
+CONFIG_NXFONTS_CHARBITS=7
+CONFIG_NX_BLOCKING=y
+CONFIG_NX_MXSERVERMSGS=32
+CONFIG_NX_MXCLIENTMSGS=16
+
+#
+# LCD Hardware Configuration
+#
+# CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
+#   support. In this orientation, the HY-MiniSTM32 screen
+#   has the used connector at the right of display.
+# CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
+#   orientation support.  In this orientation, the HY-MiniSTM32 screen
+#   has the used connector at bottom of display.
+# CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
+#   portrait" orientation support.  In this orientation, the HY-MiniSTM32
+#   screen has the used connector at top of display.
+# CONFIG_LCD_BACKLIGHT - Define to support an adjustable backlight
+#   using timer 3.  The granularity of the settings is determined
+#   by CONFIG_LCD_MAXPOWER.  Requires CONFIG_STM32_TIM3.
+#
+CONFIG_LCD_LANDSCAPE=n
+CONFIG_LCD_PORTRAIT=n
+CONFIG_LCD_RPORTRAIT=y
+CONFIG_LCD_BACKLIGHT=n
+
+#
+# Settings for examples/uip
+#
+CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_UIP_DHCPC=n
+
+#
+# Settings for examples/nettest
+CONFIG_EXAMPLE_NETTEST_SERVER=n
+CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
+CONFIG_EXAMPLE_NETTEST_NOMAC=n
+CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_CONDEV - Select the serial device used to support
+#   the NSH console.  Default: stdin and stdout
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+#CONFIG_NSH_CONDEV="/dev/ttyS1"
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=n
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Settings for examples/nx
+#
+# CONFIG_EXAMPLES_NX_BUILTIN -- Build the NX example as a "built-in"
+#  that can be executed from the NSH command line  
+# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NX_DEVNO - The LCD device to select from the LCD
+#  driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background.  Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_FONTID - Selects the font (see font ID numbers in
+#   include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 32.
+# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows;  Default is to
+#   use pretty, framed NXTK windows with toolbars.
+# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating
+#   the NX server.  Default 2048
+# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority.  Default: 80
+# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority.  Default: 120
+# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with
+#   nx_eventnotify().  Default: 4
+#
+CONFIG_EXAMPLES_NX_BUILTIN=n
+CONFIG_EXAMPLES_NX_VPLANE=0
+CONFIG_EXAMPLES_NX_DEVNO=0
+CONFIG_EXAMPLES_NX_BGCOLOR=0x0011
+CONFIG_EXAMPLES_NX_COLOR1=0xaedc
+CONFIG_EXAMPLES_NX_COLOR2=0xe7ff
+CONFIG_EXAMPLES_NX_TBCOLOR=0xd69a
+CONFIG_EXAMPLES_NX_FONTID=0
+CONFIG_EXAMPLES_NX_FONTCOLOR=0x0000
+CONFIG_EXAMPLES_NX_BPP=16
+CONFIG_EXAMPLES_NX_RAWWINDOWS=n
+CONFIG_EXAMPLES_NX_STACKSIZE=2048
+CONFIG_EXAMPLES_NX_CLIENTPRIO=80
+CONFIG_EXAMPLES_NX_SERVERPRIO=120
+CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
+CONFIG_EXAMPLES_NX_EXTERNINIT=n
+
+#
+# Settings for examples/nximage
+#
+# CONFIG_EXAMPLES_NXIMAGE_BUILTIN -- Build the NXIMAGE example as a "built-in"
+#   that can be executed from the NSH command line    
+# CONFIG_EXAMPLES_NXIMAGE_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_BPP -- Pixels per pixel to use.  Valid options
+#   include 8, 16, and 24.  Default is 16.
+# CONFIG_EXAMPLES_NXIMAGE_XSCALEp5, CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0 -- The logo image width is 160 columns.
+#   One of these may be defined to rescale the image horizontally by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_YSCALEp5, CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0 -- The logo image height is 160 rows.
+#   One of these may be defined to rescale the image vertically by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXIMAGE_BUILTIN=n
+CONFIG_EXAMPLES_NXIMAGE_VPLANE=0
+CONFIG_EXAMPLES_NXIMAGE_DEVNO=0
+CONFIG_EXAMPLES_NXIMAGE_BPP=16
+CONFIG_EXAMPLES_NXIMAGE_XSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT=n
+
+#
+# Settings for examples/nxlines
+#
+# CONFIG_EXAMPLES_NXLINES_BUILTIN -- Build the NXLINES example as a "built-in"
+#   that can be executed from the NSH command line
+# CONFIG_EXAMPLES_NXLINES_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXLINES_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXLINES_BGCOLOR -- The color of the background.  Default
+#   depends on CONFIG_EXAMPLES_NXLINES_BPP.
+# CONFIG_EXAMPLES_NXLINES_LINEWIDTH - Selects the width of the lines in
+#   pixels (default: 16)
+# CONFIG_EXAMPLES_NXLINES_LINECOLOR -- The color of the lines drawn in the
+#   background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP.
+# CONFIG_EXAMPLES_NXLINES_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 16.
+# CONFIG_EXAMPLES_NXLINES_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXLINES_BUILTIN=n
+CONFIG_EXAMPLES_NXLINES_VPLANE=0
+CONFIG_EXAMPLES_NXLINES_DEVNO=0
+CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
+CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
+CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
+CONFIG_EXAMPLES_NXLINES_BPP=16
+CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the Hy-Mini STM32v which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/hymini-stm32v/nx/ld.script b/nuttx/configs/hymini-stm32v/nx/ld.script
new file mode 100644
index 000000000..c4a12d2b9
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nx/ld.script
@@ -0,0 +1,112 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nx/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
+ * 48Kb of SRAM beginning at address 0x2000:0000.  When booting from FLASH,
+ * FLASH memory is aliased to address 0x0000:0000 where the code expects to
+ * begin execution by jumping to the entry point in the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nx/ld.script.dfu b/nuttx/configs/hymini-stm32v/nx/ld.script.dfu
new file mode 100644
index 000000000..bd995086f
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nx/ld.script.dfu
@@ -0,0 +1,111 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nx/ld.script.dfu
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  Here we assume that the
+ * Hy-Mini STM32v's DFU bootloader is being used.  In that case, the corrct
+ * load .text load address is 0x08003000 (leaving 464Kb).
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nx/setenv.sh b/nuttx/configs/hymini-stm32v/nx/setenv.sh
new file mode 100755
index 000000000..4e9fdb4ec
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nx/setenv.sh
@@ -0,0 +1,62 @@
+#!/bin/bash
+# configs/hymini-stm32v/nx/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+# This the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+
+# This the Cygwin path to the location where I build the buildroot
+# toolchain.
+#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/hymini-stm32v/nxlines/Make.defs b/nuttx/configs/hymini-stm32v/nxlines/Make.defs
new file mode 100644
index 000000000..213e8fbef
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nxlines/Make.defs
@@ -0,0 +1,176 @@
+############################################################################
+# configs/hymini-stm32v/nxlines/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_DFU),y)
+  LDSCRIPT = ld.script.dfu
+else
+  LDSCRIPT = ld.script
+endif
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O1
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O1
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nxlines/$(LDSCRIPT)}"
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nxlines/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/hymini-stm32v/nxlines/appconfig b/nuttx/configs/hymini-stm32v/nxlines/appconfig
new file mode 100644
index 000000000..bf30ded8b
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nxlines/appconfig
@@ -0,0 +1,39 @@
+############################################################################
+# configs/hymini-stm32v/nxlines/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/nxlines
+
diff --git a/nuttx/configs/hymini-stm32v/nxlines/defconfig b/nuttx/configs/hymini-stm32v/nxlines/defconfig
new file mode 100644
index 000000000..1e88a048c
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nxlines/defconfig
@@ -0,0 +1,1209 @@
+############################################################################
+# configs/hymini-stm32v/nxlines/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+# CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM3=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F103VCT6=y
+CONFIG_ARCH_BOARD=hymini-stm32v
+CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+
+CONFIG_BOARD_LOOPSPERMSEC=5483
+CONFIG_DRAM_SIZE=0x0000C000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=n
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=y
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+CONFIG_STM32_DFU=n
+
+#
+# Individual subsystems can be enabled:
+# AHB: 
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=y
+CONFIG_STM32_CRC=n
+CONFIG_STM32_FSMC=y
+CONFIG_STM32_SDIO=y
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI4=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=y
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_USB=y
+CONFIG_STM32_CAN=n
+CONFIG_STM32_BKP=n
+CONFIG_STM32_PWR=n
+CONFIG_STM32_DAC=n
+
+CONFIG_STM32_TIM3_PARTIAL_REMAP=y
+
+# APB2:
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_SPI1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=y
+CONFIG_STM32_ADC3=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F103Z specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART2_SERIAL_CONSOLE=n
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=256
+CONFIG_USART2_TXBUFSIZE=256
+CONFIG_USART3_TXBUFSIZE=256
+CONFIG_USART4_TXBUFSIZE=256
+CONFIG_USART5_TXBUFSIZE=256
+
+CONFIG_USART1_RXBUFSIZE=256
+CONFIG_USART2_RXBUFSIZE=256
+CONFIG_USART3_RXBUFSIZE=256
+CONFIG_USART4_RXBUFSIZE=256
+CONFIG_USART5_RXBUFSIZE=256
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F103V specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=n
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=y
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=n
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_GRAPHICS=n
+CONFIG_DEBUG_LCD=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_MM_REGIONS=1
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2011
+CONFIG_START_MONTH=7
+CONFIG_START_DAY=8
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=y
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SCHED_WORKQUEUE=y
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+
+#
+# Settings for NXFLAT
+#
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
+#  with.  CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
+#  CONFIG_DEBUG_BINFMT have to be defined or
+#  CONFIG_NXFLAT_DUMPBUFFER does nothing.
+# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
+#  is ordered by symbol name
+#
+CONFIG_NXFLAT=n
+CONFIG_NXFLAT_DUMPBUFFER=n
+CONFIG_SYMTAB_ORDEREDBYNAME=y
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=y
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_DISABLE_ENVIRON=y
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=12
+CONFIG_NFILE_STREAMS=12
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Framebuffer driver options
+#
+CONFIG_FB_CMAP=n
+CONFIG_FB_HWCURSOR=n
+CONFIG_FB_HWCURSORIMAGE=n
+#CONFIG_FB_HWCURSORSIZE
+#CONFIG_FB_TRANSPARENCY
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=n
+CONFIG_FAT_LCNAMES=n
+CONFIG_FAT_LFN=n
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=1
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=y
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=0
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=420
+CONFIG_NET_TCP=n
+CONFIG_NET_TCP_CONNS=40
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=n
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=n
+CONFIG_NET_ICMP_PING=n
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=n
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=n
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Graphics related configuration settings
+#
+# CONFIG_NX
+#   Enables overall support for graphics library and NX
+# CONFIG_NX_MULTIUSER
+#   Configures NX in multi-user mode
+# CONFIG_NX_NPLANES
+#   Some YUV color formats requires support for multiple planes,
+#   one for each color component.  Unless you have such special
+#   hardware, this value should be undefined or set to 1
+# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
+# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
+# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
+# CONFIG_NX_DISABLE_32BPP
+#   NX supports a variety of pixel depths.  You can save some
+#   memory by disabling support for unused color depths.
+# CONFIG_NX_PACKEDMSFIRST
+#   If a pixel depth of less than 8-bits is used, then NX needs
+#   to know if the pixels pack from the MS to LS or from LS to MS
+# CONFIG_NX_LCDDRIVER
+#   By default, NX builds to use a framebuffer driver (see
+#   include/nuttx/fb.h). If this option is defined, NX will
+#   build to use an LCD driver (see include/nuttx/lcd/lcd.h).
+# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
+# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
+# CONFIG_NX_MOUSE
+#   Build in support for mouse input
+# CONFIG_NX_KBD
+#   Build in support of keypad/keyboard input
+# CONFIG_NXTK_BORDERWIDTH
+#   Specifies with with of the border (in pixels) used with
+#   framed windows.  The default is 4.
+# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
+#   Specify the colors of the border used with framed windows.
+#   CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
+#   is normally darker.  The default is medium and dark grey,
+#   respectively
+# CONFIG_NXTK_AUTORAISE
+#   If set, a window will be raised to the top if the mouse position
+#   is over a visible portion of the window.  Default: A mouse
+#   button must be clicked over a visible portion of the window.
+# CONFIG_NXFONTS_CHARBITS
+#   The number of bits in the character set.  Current options are
+#   only 7 and 8.  The default is 7.
+# CONFIG_NXFONT_SANS23X27
+#   This option enables support for a tiny, 23x27 san serif font
+#   (font ID FONTID_SANS23X27 == 1).
+# CONFIG_NXFONT_SANS22X29
+#   This option enables support for a small, 22x29 san serif font
+#   (font ID FONTID_SANS22X29 == 2).
+# CONFIG_NXFONT_SANS28X37
+#   This option enables support for a medium, 28x37 san serif font
+#   (font ID FONTID_SANS28X37 == 3).
+# CONFIG_NXFONT_SANS39X48
+#   This option enables support for a large, 39x48 san serif font
+#   (font ID FONTID_SANS39X48 == 4).
+# CONFIG_NXFONT_SANS22X29B
+#   This option enables support for a small, 22x29 san serif bold font
+#   (font ID FONTID_SANS22X29B == 5).
+# CONFIG_NXFONT_SANS28X37B
+#   This option enables support for a medium, 28x37 san serif bold font
+#   (font ID FONTID_SANS28X37B == 6).
+# CONFIG_NXFONT_SANS40X49B
+#   This option enables support for a large, 40x49 san serif bold font
+#   (font ID FONTID_SANS40X49B == 7).
+# CONFIG_NXFONT_SERIF22X29
+#   This option enables support for a small, 22x29 font (with serifs)
+#   (font ID FONTID_SERIF22X29 == 8).
+# CONFIG_NXFONT_SERIF29X37
+#   This option enables support for a medium, 29x37 font (with serifs)
+#   (font ID FONTID_SERIF29X37 == 9).
+# CONFIG_NXFONT_SERIF38X48
+#   This option enables support for a large, 38x48 font (with serifs)
+#   (font ID FONTID_SERIF38X48 == 10).
+# CONFIG_NXFONT_SERIF22X28B
+#   This option enables support for a small, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF22X28B == 11).
+# CONFIG_NXFONT_SERIF27X38B
+#   This option enables support for a medium, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF27X38B == 12).
+# CONFIG_NXFONT_SERIF38X49B
+#   This option enables support for a large, 38x49 bold font (with serifs)
+#   (font ID FONTID_SERIF38X49B == 13).
+#
+# NX Multi-user only options:
+#
+# CONFIG_NX_BLOCKING
+#   Open the client message queues in blocking mode.  In this case,
+#   nx_eventhandler()  will not return until a message is received and processed.
+# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
+#   Specifies the maximum number of messages that can fit in
+#   the message queues.  No additional resources are allocated, but
+#   this can be set to prevent flooding of the client or server with
+#   too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
+#   messages are pre-allocated).
+#
+CONFIG_NX=y
+CONFIG_NX_MULTIUSER=n
+CONFIG_NX_NPLANES=1
+CONFIG_NX_DISABLE_1BPP=y
+CONFIG_NX_DISABLE_2BPP=y
+CONFIG_NX_DISABLE_4BPP=y
+CONFIG_NX_DISABLE_8BPP=y
+CONFIG_NX_DISABLE_16BPP=n
+CONFIG_NX_DISABLE_24BPP=y
+CONFIG_NX_DISABLE_32BPP=y
+CONFIG_NX_PACKEDMSFIRST=n
+CONFIG_NX_LCDDRIVER=y
+
+CONFIG_NX_MOUSE=y
+CONFIG_NX_KBD=y
+#CONFIG_NXTK_BORDERWIDTH=4
+CONFIG_NXTK_BORDERCOLOR1=0xd69a
+CONFIG_NXTK_BORDERCOLOR2=0xad55
+CONFIG_NXFONT_SANS22X29=n
+CONFIG_NXFONT_SANS23X27=y
+CONFIG_NXFONT_SANS28X37=n
+CONFIG_NXFONT_SANS22X29B=n
+CONFIG_NXFONT_SANS28X37B=n
+CONFIG_NXFONT_SANS40X49B=n
+CONFIG_NXFONT_SERIF22X29=n
+CONFIG_NXFONT_SERIF29X37=n
+CONFIG_NXFONT_SERIF38X48=n
+CONFIG_NXFONT_SERIF22X28B=y
+CONFIG_NXFONT_SERIF27X38B=n
+CONFIG_NXFONT_SERIF38X49B=n
+CONFIG_NXFONTS_CHARBITS=7
+CONFIG_NX_BLOCKING=y
+CONFIG_NX_MXSERVERMSGS=32
+CONFIG_NX_MXCLIENTMSGS=16
+
+#
+# LCD Hardware Configuration
+#
+# CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
+#   support. In this orientation, the HY-MiniSTM32 screen
+#   has the used connector at the right of display.
+# CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
+#   orientation support.  In this orientation, the HY-MiniSTM32 screen
+#   has the used connector at bottom of display.
+# CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
+#   portrait" orientation support.  In this orientation, the HY-MiniSTM32
+#   screen has the used connector at top of display.
+# CONFIG_LCD_BACKLIGHT - Define to support an adjustable backlight
+#   using timer 3.  The granularity of the settings is determined
+#   by CONFIG_LCD_MAXPOWER.  Requires CONFIG_STM32_TIM3.
+#
+CONFIG_LCD_LANDSCAPE=y
+CONFIG_LCD_PORTRAIT=n
+CONFIG_LCD_RPORTRAIT=n
+CONFIG_LCD_BACKLIGHT=y
+
+# Configurable steps for the LCD backlight
+CONFIG_LCD_MAXPOWER=100
+
+# Not used
+CONFIG_LCD_MAXCONTRAST=100
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_CONDEV - Select the serial device used to support
+#   the NSH console.  Default: stdin and stdout
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+CONFIG_NSH_CONDEV="/dev/ttyS1"
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=n
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Settings for examples/nx
+#
+# CONFIG_EXAMPLES_NX_BUILTIN -- Build the NX example as a "built-in"
+#  that can be executed from the NSH command line  
+# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NX_DEVNO - The LCD device to select from the LCD
+#  driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background.  Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_FONTID - Selects the font (see font ID numbers in
+#   include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 32.
+# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows;  Default is to
+#   use pretty, framed NXTK windows with toolbars.
+# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating
+#   the NX server.  Default 2048
+# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority.  Default: 80
+# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority.  Default: 120
+# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with
+#   nx_eventnotify().  Default: 4
+#
+CONFIG_EXAMPLES_NX_BUILTIN=n
+CONFIG_EXAMPLES_NX_VPLANE=0
+CONFIG_EXAMPLES_NX_DEVNO=0
+CONFIG_EXAMPLES_NX_BGCOLOR=0x0011
+CONFIG_EXAMPLES_NX_COLOR1=0xaedc
+CONFIG_EXAMPLES_NX_COLOR2=0xe7ff
+CONFIG_EXAMPLES_NX_TBCOLOR=0xd69a
+CONFIG_EXAMPLES_NX_FONTID=0
+CONFIG_EXAMPLES_NX_FONTCOLOR=0x0000
+CONFIG_EXAMPLES_NX_BPP=16
+CONFIG_EXAMPLES_NX_RAWWINDOWS=n
+CONFIG_EXAMPLES_NX_STACKSIZE=2048
+CONFIG_EXAMPLES_NX_CLIENTPRIO=80
+CONFIG_EXAMPLES_NX_SERVERPRIO=120
+CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
+CONFIG_EXAMPLES_NX_EXTERNINIT=n
+
+#
+# Settings for examples/nxtext
+#
+# CONFIG_EXAMPLES_NXTEXT_BUILTIN -- Build the NXTEXT example as a "built-in"
+#  that can be executed from the NSH command line  
+# CONFIG_EXAMPLES_NXTEXT_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXTEXT_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXTEXT_BGCOLOR -- The color of the background.  Default
+#   depends on CONFIG_EXAMPLES_NXTEXT_BPP.
+# CONFIG_EXAMPLES_NXTEXT_BGFONTID - Selects the font to use in the
+#   background text (see font ID numbers in include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NXTEXT_BGFONTCOLOR -- The color of the fonts used in the
+#   background window. Default depends on CONFIG_EXAMPLES_NXTEXT_BPP.
+# CONFIG_EXAMPLES_NXTEXT_PUCOLOR -- The color of the pop-up window.  Default
+#   depends on CONFIG_EXAMPLES_NXTEXT_BPP.
+# CONFIG_EXAMPLES_NXTEXT_PUFONTID - Selects the font to use in the pop-up
+#   windows (see font ID numbers in include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NXTEXT_PUFONTCOLOR -- The color of the fonts used in the
+#   background window. Default depends on CONFIG_EXAMPLES_NXTEXT_BPP.
+# CONFIG_EXAMPLES_NXTEXT_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 32.
+# CONFIG_EXAMPLES_NXTEXT_NOGETRUN -- If your display is read-only OR if
+#   reading is not reliable, then select this configuration to avoid
+#   reading from the display.
+# CONFIG_EXAMPLES_NXTEXT_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.
+# CONFIG_EXAMPLES_NXTEXT_BMCACHE - The maximum number of characters that
+#   can be put in the background window.  Default is 128.
+# CONFIG_EXAMPLES_NXTEXT_GLCACHE - The maximum number of pre-rendered
+#   fonts that can be retained for the background window.  Default is 16.
+# CONFIG_EXAMPLES_NXTEXT_STACKSIZE -- The stacksize to use when creating
+#  the NX server.  Default 2048
+# CONFIG_EXAMPLES_NXTEXT_CLIENTPRIO -- The client priority.  Default: 100
+# CONFIG_EXAMPLES_NXTEXT_SERVERPRIO -- The server priority.  Default: 120
+# CONFIG_EXAMPLES_NXTEXT_LISTENERPRIO -- The priority of the event listener
+#   thread. Default 80.
+# CONFIG_EXAMPLES_NXTEXT_NOTIFYSIGNO -- The signal number to use with
+#   nx_eventnotify().  Default: 4
+#
+CONFIG_EXAMPLES_NXTEXT_BUILTIN=n
+CONFIG_EXAMPLES_NXTEXT_VPLANE=0
+CONFIG_EXAMPLES_NXTEXT_DEVNO=0
+CONFIG_EXAMPLES_NXTEXT_BGCOLOR=0x0011
+CONFIG_EXAMPLES_NXTEXT_BGFONTID=11
+CONFIG_EXAMPLES_NXTEXT_BGFONTCOLOR=0xffdf
+CONFIG_EXAMPLES_NXTEXT_PUCOLOR=0xfd20
+CONFIG_EXAMPLES_NXTEXT_PUFONTID=1
+CONFIG_EXAMPLES_NXTEXT_PUFONTCOLOR=0x001f
+CONFIG_EXAMPLES_NXTEXT_BPP=16
+CONFIG_EXAMPLES_NXTEXT_NOGETRUN=y
+CONFIG_EXAMPLES_NXTEXT_EXTERNINIT=n
+CONFIG_EXAMPLES_NXTEXT_BMCACHE=512
+CONFIG_EXAMPLES_NXTEXT_GLCACHE=16
+CONFIG_EXAMPLES_NXTEXT_STACKSIZE=2048
+CONFIG_EXAMPLES_NXTEXT_CLIENTPRIO=80
+CONFIG_EXAMPLES_NXTEXT_SERVERPRIO=120
+CONFIG_EXAMPLES_NXTEXT_NOTIFYSIGNO=4
+
+#
+# Settings for examples/nximage
+#
+# CONFIG_EXAMPLES_NXIMAGE_BUILTIN -- Build the NXIMAGE example as a "built-in"
+#   that can be executed from the NSH command line
+# CONFIG_EXAMPLES_NXIMAGE_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_BPP -- Pixels per pixel to use.  Valid options
+#   include 8, 16, and 24.  Default is 16.
+# CONFIG_EXAMPLES_NXIMAGE_XSCALEp5, CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0 -- The logo image width is 160 columns.
+#   One of these may be defined to rescale the image horizontally by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_YSCALEp5, CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0 -- The logo image height is 160 rows.
+#   One of these may be defined to rescale the image vertically by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXIMAGE_BUILTIN=n
+CONFIG_EXAMPLES_NXIMAGE_VPLANE=0
+CONFIG_EXAMPLES_NXIMAGE_DEVNO=0
+CONFIG_EXAMPLES_NXIMAGE_BPP=16
+CONFIG_EXAMPLES_NXIMAGE_XSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT=n
+
+#
+# Settings for examples/nxlines
+#
+# CONFIG_EXAMPLES_NXLINES_BUILTIN -- Build the NXLINES example as a "built-in"
+#   that can be executed from the NSH command line
+# CONFIG_EXAMPLES_NXLINES_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXLINES_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXLINES_BGCOLOR -- The color of the background.  Default
+#   depends on CONFIG_EXAMPLES_NXLINES_BPP.
+# CONFIG_EXAMPLES_NXLINES_LINEWIDTH - Selects the width of the lines in
+#   pixels (default: 16)
+# CONFIG_EXAMPLES_NXLINES_LINECOLOR -- The color of the central lines drawn
+#   in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_BORDERWIDTH -- The width of the circular border
+#   drawn in the background window. (default: 4).
+# CONFIG_EXAMPLES_NXLINES_BORDERCOLOR -- The color of the circular border
+#   drawn in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR -- The color of the circular region
+#   filled in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 16.
+# CONFIG_EXAMPLES_NXLINES_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXLINES_BUILTIN=n
+CONFIG_EXAMPLES_NXLINES_VPLANE=0
+CONFIG_EXAMPLES_NXLINES_DEVNO=0
+CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
+CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
+CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
+CONFIG_EXAMPLES_NXLINES_BORDERWIDTH=4
+CONFIG_EXAMPLES_NXLINES_BORDERCOLOR=0xffe0
+CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR=0xf7bb
+CONFIG_EXAMPLES_NXLINES_BPP=16
+CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the Hy-Mini STM32v which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/hymini-stm32v/nxlines/ld.script b/nuttx/configs/hymini-stm32v/nxlines/ld.script
new file mode 100644
index 000000000..4938ad501
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nxlines/ld.script
@@ -0,0 +1,112 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nxlines/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
+ * 48Kb of SRAM beginning at address 0x2000:0000.  When booting from FLASH,
+ * FLASH memory is aliased to address 0x0000:0000 where the code expects to
+ * begin execution by jumping to the entry point in the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nxlines/ld.script.dfu b/nuttx/configs/hymini-stm32v/nxlines/ld.script.dfu
new file mode 100644
index 000000000..b64109da8
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nxlines/ld.script.dfu
@@ -0,0 +1,111 @@
+/****************************************************************************
+ * configs/hymini-stm32v/nxlines/ld.script.dfu
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  Here we assume that the
+ * Hy-Mini STM32v's DFU bootloader is being used.  In that case, the corrct
+ * load .text load address is 0x08003000 (leaving 464Kb).
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/nxlines/setenv.sh b/nuttx/configs/hymini-stm32v/nxlines/setenv.sh
new file mode 100755
index 000000000..53ccb2d0f
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/nxlines/setenv.sh
@@ -0,0 +1,53 @@
+#!/bin/bash
+# configs/hymini-stm32v/nxlines/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!"
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
+export PATH="${BUILDROOT_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/hymini-stm32v/src/Makefile b/nuttx/configs/hymini-stm32v/src/Makefile
new file mode 100644
index 000000000..d79260748
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/Makefile
@@ -0,0 +1,102 @@
+############################################################################
+# configs/hymini-stm32v/src/Makefile
+#
+#   Copyright (C) 2009-2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#           Laurent Latil <laurent@latil.nom.fr>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+-include $(TOPDIR)/Make.defs
+
+CFLAGS		+= -I$(TOPDIR)/sched
+
+ASRCS		= 
+AOBJS		= $(ASRCS:.S=$(OBJEXT))
+
+CSRCS		= up_boot.c up_leds.c up_buttons.c up_spi.c up_usbdev.c
+
+ifeq ($(CONFIG_NX_LCDDRIVER),y)
+CSRCS		+= ssd1289.c
+endif
+
+ifeq ($(CONFIG_NSH_ARCHINIT),y)
+CSRCS		+= up_nsh.c
+endif
+
+ifeq ($(CONFIG_INPUT),y)
+CSRCS		+= up_ts.c
+endif
+
+ifeq ($(CONFIG_USBSTRG),y)
+CSRCS		+= up_usbstrg.c
+endif
+
+COBJS		= $(CSRCS:.c=$(OBJEXT))
+
+SRCS		= $(ASRCS) $(CSRCS)
+OBJS		= $(AOBJS) $(COBJS)
+
+ARCH_SRCDIR	= $(TOPDIR)/arch/$(CONFIG_ARCH)/src
+ifeq ($(WINTOOL),y)
+  CFLAGS	+= -I "${shell cygpath -w $(ARCH_SRCDIR)/chip}" \
+  		   -I "${shell cygpath -w $(ARCH_SRCDIR)/common}" \
+  		   -I "${shell cygpath -w $(ARCH_SRCDIR)/armv7-m}"
+else
+  CFLAGS	+= -I$(ARCH_SRCDIR)/chip -I$(ARCH_SRCDIR)/common -I$(ARCH_SRCDIR)/armv7-m
+endif
+
+all: libboard$(LIBEXT)
+
+$(AOBJS): %$(OBJEXT): %.S
+	$(call ASSEMBLE, $<, $@)
+
+$(COBJS) $(LINKOBJS): %$(OBJEXT): %.c
+	$(call COMPILE, $<, $@)
+
+libboard$(LIBEXT): $(OBJS)
+	@( for obj in $(OBJS) ; do \
+		$(call ARCHIVE, $@, $${obj}); \
+	done ; )
+
+.depend: Makefile $(SRCS)
+	@$(MKDEP) $(CC) -- $(CFLAGS) -- $(SRCS) >Make.dep
+	@touch $@
+
+depend: .depend
+
+clean:
+	@rm -f libboard$(LIBEXT) *~ .*.swp
+	$(call CLEAN)
+
+distclean: clean
+	@rm -f Make.dep .depend
+
+-include Make.dep
diff --git a/nuttx/configs/hymini-stm32v/src/README.txt b/nuttx/configs/hymini-stm32v/src/README.txt
new file mode 100644
index 000000000..d7c4f97cc
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/README.txt
@@ -0,0 +1 @@
+This directory contains drivers unique to the HY-MiniSTM32V development board.
diff --git a/nuttx/configs/hymini-stm32v/src/hymini_stm32v-internal.h b/nuttx/configs/hymini-stm32v/src/hymini_stm32v-internal.h
new file mode 100644
index 000000000..718220454
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/hymini_stm32v-internal.h
@@ -0,0 +1,153 @@
+/************************************************************************************
+ * configs/hymini-stm32v/src/hymini_stm32v-internal.h
+ * arch/arm/src/board/hymini_stm32v-internal.h
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *           Laurent Latil <laurent@latil.nom.fr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+#ifndef __CONFIGS_HYMINI_STM32V_INTERNAL_H
+#define __CONFIGS_HYMINI_STM32V_INTERNAL_H
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/* How many SPI modules does this chip support? The LM3S6918 supports 2 SPI
+ * modules (others may support more -- in such case, the following must be
+ * expanded).
+ */
+
+#if STM32_NSPI < 1
+#  undef CONFIG_STM32_SPI1
+#  undef CONFIG_STM32_SPI2
+#elif STM32_NSPI < 2
+#  undef CONFIG_STM32_SPI2
+#endif
+
+/* GPIOs **************************************************************/
+/* LEDs */
+
+#define GPIO_LED1       (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
+                         GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN0)
+#define GPIO_LED2       (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
+                         GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN1)
+
+/* BUTTONS -- NOTE that some have EXTI interrupts configured */
+
+#define MIN_IRQBUTTON   BUTTON_KEYA
+#define MAX_IRQBUTTON   BUTTON_KEYB
+#define NUM_IRQBUTTONS  NUM_BUTTONS
+
+/* Button A is externally pulled up */
+#define GPIO_BTN_KEYA (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
+                         GPIO_PORTC|GPIO_PIN13)
+
+/* Button B is externally pulled dw */
+#define GPIO_BTN_KEYB (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
+                         GPIO_PORTB|GPIO_PIN2)
+
+/* SPI touch screen (ADS7843) chip select:  PA.4 */
+
+#define GPIO_TS_CS   (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
+                         GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
+
+/* Touch screen (ADS7843) IRQ pin:  PB.6 */
+#define GPIO_TS_IRQ  (GPIO_INPUT|GPIO_CNF_INPULLUP|GPIO_MODE_INPUT|\
+                         GPIO_PORTB|GPIO_PIN6)
+
+/* USB Soft Connect Pullup: PB.7 */
+#define GPIO_USB_PULLUP (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|\
+                         GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN7)
+
+/* SD card detect pin: PD.3 */
+#define GPIO_SD_CD (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
+                         GPIO_PORTD|GPIO_PIN3)
+
+/************************************************************************************
+ * Public Types
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public data
+ ************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the Hy-Mini STM32v board.
+ *
+ ************************************************************************************/
+
+extern void weak_function stm32_spiinitialize(void);
+
+/************************************************************************************
+ * Name: stm32_usbinitialize
+ *
+ * Description:
+ *   Called to setup USB-related GPIO pins for the Hy-Mini STM32v board.
+ *
+ ************************************************************************************/
+
+extern void weak_function stm32_usbinitialize(void);
+
+#if defined(CONFIG_INPUT_ADS7843E)
+
+/************************************************************************************
+ * Name: Touchscreen initialization
+ *
+ ************************************************************************************/
+
+extern int arch_tcinitialize(int minor);
+
+extern void arch_tcuninitialize(void);
+
+#endif /* CONFIG_INPUT_ADS7843E */
+
+#endif /* __ASSEMBLY__ */
+#endif /* __CONFIGS_HYMINI_STM32V_INTERNAL_H */
+
diff --git a/nuttx/configs/hymini-stm32v/src/ssd1289.c b/nuttx/configs/hymini-stm32v/src/ssd1289.c
new file mode 100644
index 000000000..0ebf82274
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/ssd1289.c
@@ -0,0 +1,989 @@
+/************************************************************************************
+ * configs/hymini-stm32v/src/ssd1289.c
+ * arch/arm/src/board/ssd1289.c
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *           Laurent Latil <laurent@latil.nom.fr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <sys/types.h>
+#include <stdint.h>
+#include <stdbool.h>
+#include <string.h>
+#include <errno.h>
+#include <debug.h>
+
+#include <nuttx/arch.h>
+#include <nuttx/spi.h>
+
+#include <arch/board/board.h>
+
+#include "up_arch.h"
+#include "stm32.h"
+#include "stm32_internal.h"
+#include "hymini_stm32v-internal.h"
+
+#include "ssd1289.h"
+
+/* Color depth and format */
+#define LCD_BPP          16
+#define LCD_COLORFMT     FB_FMT_RGB16_565
+
+/* Display Resolution */
+#if defined(CONFIG_LCD_LANDSCAPE)
+#  define LCD_XRES       320
+#  define LCD_YRES       240
+#else
+#  define LCD_XRES       240
+#  define LCD_YRES       320
+#endif
+
+#define LCD_BL_TIMER_PERIOD   8999
+
+
+/* Debug ******************************************************************************/
+#ifdef CONFIG_DEBUG_LCD
+# define lcddbg(format, arg...)  vdbg(format, ##arg)
+#else
+# define lcddbg(x...)
+#endif
+
+/* LCD is connected to the FSMC_Bank1_NOR/SRAM1 and NE1 is used as ship select signal */
+/* RS <==> A16 */
+#define LCD_REG              (*((volatile unsigned short *) 0x60000000)) /* RS = 0 */
+#define LCD_RAM              (*((volatile unsigned short *) 0x60020000)) /* RS = 1 */
+
+const uint16_t fsmc_gpios[] =
+{ /* A16... A24 */
+  GPIO_NPS_A16, GPIO_NPS_A17, GPIO_NPS_A18, GPIO_NPS_A19, GPIO_NPS_A20,
+  GPIO_NPS_A21, GPIO_NPS_A22, GPIO_NPS_A23,
+
+  /* D0... D15 */GPIO_NPS_D0, GPIO_NPS_D1, GPIO_NPS_D2, GPIO_NPS_D3,
+  GPIO_NPS_D4, GPIO_NPS_D5, GPIO_NPS_D6, GPIO_NPS_D7, GPIO_NPS_D8, GPIO_NPS_D9,
+  GPIO_NPS_D10, GPIO_NPS_D11, GPIO_NPS_D12, GPIO_NPS_D13, GPIO_NPS_D14,
+  GPIO_NPS_D15,
+
+  /* NOE, NWE  */GPIO_NPS_NOE, GPIO_NPS_NWE,
+
+  /* NE1  */GPIO_NPS_NE1 };
+
+#define NGPIOS (sizeof(fsmc_gpios)/sizeof(uint16_t))
+
+/** This should be put elsewhere */
+#ifdef __CC_ARM               /* ARM Compiler        */
+#define lcd_inline            static __inline
+#elif defined (__ICCARM__)    /* for IAR Compiler */
+#define lcd_inline            inline
+#elif defined (__GNUC__)      /* GNU GCC Compiler */
+#define lcd_inline            static __inline
+#else
+#define lcd_inline            static
+#endif
+
+/* Low Level methods */
+void lcd_clear(uint16_t color);
+
+/* LCD Data Transfer Methods */
+int lcd_putrun(fb_coord_t row, fb_coord_t col, FAR const uint8_t *buffer,
+    size_t npixels);
+int lcd_getrun(fb_coord_t row, fb_coord_t col, FAR uint8_t *buffer,
+    size_t npixels);
+
+/* LCD Configuration */
+static int lcd_getvideoinfo(FAR struct lcd_dev_s *dev,
+    FAR struct fb_videoinfo_s *vinfo);
+static int lcd_getplaneinfo(FAR struct lcd_dev_s *dev, unsigned int planeno,
+    FAR struct lcd_planeinfo_s *pinfo);
+
+/* LCD RGB Mapping */
+#ifdef CONFIG_FB_CMAP
+#  error "RGB color mapping not supported by this driver"
+#endif
+
+/* Cursor Controls */
+#ifdef CONFIG_FB_HWCURSOR
+#  error "Cursor control not supported by this driver"
+#endif
+
+/* LCD Specific Controls */
+static int lcd_getpower(struct lcd_dev_s *dev);
+static int lcd_setpower(struct lcd_dev_s *dev, int power);
+static int lcd_getcontrast(struct lcd_dev_s *dev);
+static int lcd_setcontrast(struct lcd_dev_s *dev, unsigned int contrast);
+
+/* Initialization (LCD ctrl / backlight) */
+static inline void lcd_initialize(void);
+
+#ifdef CONFIG_LCD_BACKLIGHT
+static void lcd_backlight(void);
+#else
+#  define lcd_backlight()
+#endif
+
+/**************************************************************************************
+ * Private Data
+ **************************************************************************************/
+
+/* This is working memory allocated by the LCD driver for each LCD device
+ * and for each color plane.  This memory will hold one raster line of data.
+ * The size of the allocated run buffer must therefore be at least
+ * (bpp * xres / 8).  Actual alignment of the buffer must conform to the
+ * bitwidth of the underlying pixel type.
+ *
+ * If there are multiple planes, they may share the same working buffer
+ * because different planes will not be operate on concurrently.  However,
+ * if there are multiple LCD devices, they must each have unique run buffers.
+ */
+
+static uint16_t g_runbuffer[LCD_XRES];
+
+/* This structure describes the overall LCD video controller */
+
+static const struct fb_videoinfo_s g_videoinfo =
+{ .fmt = LCD_COLORFMT, /* Color format: RGB16-565: RRRR RGGG GGGB BBBB */
+  .xres = LCD_XRES, /* Horizontal resolution in pixel columns */
+  .yres = LCD_YRES, /* Vertical resolution in pixel rows */
+  .nplanes = 1, /* Number of color planes supported */
+};
+
+/* This is the standard, NuttX Plane information object */
+
+static const struct lcd_planeinfo_s g_planeinfo =
+{ .putrun = lcd_putrun, /* Put a run into LCD memory */
+  .getrun = lcd_getrun, /* Get a run from LCD memory */
+  .buffer = (uint8_t*) g_runbuffer, /* Run scratch buffer */
+  .bpp = LCD_BPP, /* Bits-per-pixel */
+};
+
+/* This is the standard, NuttX LCD driver object */
+
+static struct ssd1289_dev_s g_lcddev =
+{ .dev =
+  {
+    /* LCD Configuration */
+
+    .getvideoinfo = lcd_getvideoinfo,
+    .getplaneinfo = lcd_getplaneinfo,
+
+/* LCD RGB Mapping -- Not supported */
+/* Cursor Controls -- Not supported */
+
+/* LCD Specific Controls */
+    .getpower = lcd_getpower,
+    .setpower = lcd_setpower,
+    .getcontrast = lcd_getcontrast,
+    .setcontrast = lcd_setcontrast,
+  },
+  .power=0
+};
+
+/************************************************************************************
+ * Name: stm32_extmemgpios
+ *
+ * Description:
+ *   Initialize GPIOs for NOR or SRAM
+ *
+ ************************************************************************************/
+
+static inline void stm32_extmemgpios(const uint16_t *gpios, int ngpios)
+{
+  int i;
+
+  /* Configure GPIOs */
+  for (i = 0; i < ngpios; i++)
+  {
+    stm32_configgpio(gpios[i]);
+  }
+}
+
+/************************************************************************************
+ * Name: stm32_enablefsmc
+ *
+ * Description:
+ *  enable clocking to the FSMC module
+ *
+ ************************************************************************************/
+
+#ifndef CONFIG_STM32_FSMC
+#  error CONFIG_STM32_FSMC is required for LCD support
+#endif
+
+static void stm32_enablefsmc(void)
+{
+  uint32_t regval;
+
+  /* Enable AHB clocking to the FSMC */
+
+  regval  = getreg32( STM32_RCC_AHBENR);
+  regval |= RCC_AHBENR_FSMCEN;
+  putreg32(regval, STM32_RCC_AHBENR);
+}
+
+/************************************************************************************
+ * Name: stm32_disablefsmc
+ *
+ * Description:
+ *  enable clocking to the FSMC module
+ *
+ ************************************************************************************/
+
+static void stm32_disablefsmc(void)
+{
+  uint32_t regval;
+
+  /* Enable AHB clocking to the FSMC */
+
+  regval  = getreg32( STM32_RCC_AHBENR);
+  regval &= ~RCC_AHBENR_FSMCEN;
+  putreg32(regval, STM32_RCC_AHBENR);
+}
+
+/************************************************************************************
+ * Name: stm32_selectlcd
+ *
+ * Description:
+ *   Initialize to the LCD
+ *
+ ************************************************************************************/
+
+static void stm32_selectlcd(void)
+{
+  /* Configure new GPIO state */
+  stm32_extmemgpios(fsmc_gpios, NGPIOS);
+
+  /* Enable AHB clocking to the FSMC */
+  stm32_enablefsmc();
+
+  /* Bank1 NOR/SRAM control register configuration */
+  putreg32(FSMC_BCR_SRAM | FSMC_BCR_MWID16 | FSMC_BCR_WREN, STM32_FSMC_BCR1);
+
+  /* Bank1 NOR/SRAM timing register configuration */
+  putreg32(
+      FSMC_BTR_ADDSET(2)|FSMC_BTR_ADDHLD(0)|FSMC_BTR_DATAST(2)|FSMC_BTR_BUSTRUN(0)| FSMC_BTR_CLKDIV(0)|FSMC_BTR_DATLAT(0)|FSMC_BTR_ACCMODA,
+      STM32_FSMC_BTR1);
+
+  /* As ext mode is not active the write timing is ignored!! */
+  putreg32(0xffffffff, STM32_FSMC_BWTR1);
+
+  /* Enable the bank by setting the MBKEN bit */
+  putreg32(FSMC_BCR_MBKEN | FSMC_BCR_SRAM | FSMC_BCR_MWID16 | FSMC_BCR_WREN,
+      STM32_FSMC_BCR1);
+}
+
+/************************************************************************************
+ * Name: stm32_deselectlcd
+ *
+ * Description:
+ *   Disable the LCD
+ *
+ ************************************************************************************/
+// FIXME: Check this code !!
+void stm32_deselectlcd(void)
+{
+  /* Restore registers to their power up settings */
+
+  putreg32(0xffffffff, STM32_FSMC_BCR4);
+
+  /* Bank1 NOR/SRAM timing register configuration */
+
+  putreg32(0x0fffffff, STM32_FSMC_BTR4);
+
+  /* Disable AHB clocking to the FSMC */
+
+  stm32_disablefsmc();
+}
+
+lcd_inline void write_cmd(unsigned short cmd)
+{
+  LCD_REG = cmd;
+}
+
+lcd_inline unsigned short read_data(void)
+{
+  return LCD_RAM;
+}
+
+lcd_inline void write_data(unsigned short data_code)
+{
+  LCD_RAM = data_code;
+}
+
+void write_reg(unsigned char reg_addr, unsigned short reg_val)
+{
+  write_cmd(reg_addr);
+  write_data(reg_val);
+}
+
+unsigned short read_reg(unsigned char reg_addr)
+{
+  unsigned short val;
+  write_cmd(reg_addr);
+  val = read_data();
+  return (val);
+}
+
+static inline void lcd_gramselect(void)
+{
+  write_cmd(0x22);
+}
+
+void lcd_setcursor(unsigned int x, unsigned int y)
+{
+#if defined(CONFIG_LCD_PORTRAIT) || defined (CONFIG_LCD_RPORTRAIT)
+# if defined (CONFIG_LCD_RPORTRAIT)
+  x = (LCD_XRES - 1) - x;
+  y = (LCD_YRES - 1) - y;
+# endif
+  write_reg(0x4e, x);
+  write_reg(0x4f, y);
+#endif
+
+#if defined(CONFIG_LCD_LANDSCAPE)
+  y = (LCD_YRES - 1) - y;
+
+  write_reg(0x4e, y);
+  write_reg(0x4f, x);
+#endif
+}
+
+/**************************************************************************************
+ * Name:  lcd_putrun
+ *
+ * Description:
+ *   This method can be used to write a partial raster line to the LCD:
+ *
+ *   row     - Starting row to write to (range: 0 <= row < yres)
+ *   col     - Starting column to write to (range: 0 <= col <= xres-npixels)
+ *   buffer  - The buffer containing the run to be written to the LCD
+ *   npixels - The number of pixels to write to the LCD
+ *             (range: 0 < npixels <= xres-col)
+ *
+ **************************************************************************************/
+
+int lcd_putrun(fb_coord_t row, fb_coord_t col, FAR const uint8_t *buffer,
+    size_t npixels)
+{
+  int i;
+  FAR const uint16_t *src = (FAR const uint16_t*) buffer;
+
+  /* Buffer must be provided and aligned to a 16-bit address boundary */
+  DEBUGASSERT(buffer && ((uintptr_t)buffer & 1) == 0);
+
+  /* Write the run to GRAM. */
+  lcd_setcursor(col, row);
+
+  lcd_gramselect();
+  for (i = 0; i < npixels; i++)
+  {
+    write_data(*src++);
+  }
+  return OK;
+}
+
+/**************************************************************************************
+ * Name:  lcd_getrun
+ *
+ * Description:
+ *   This method can be used to read a partial raster line from the LCD:
+ *
+ *  row     - Starting row to read from (range: 0 <= row < yres)
+ *  col     - Starting column to read read (range: 0 <= col <= xres-npixels)
+ *  buffer  - The buffer in which to return the run read from the LCD
+ *  npixels - The number of pixels to read from the LCD
+ *            (range: 0 < npixels <= xres-col)
+ *
+ **************************************************************************************/
+
+int lcd_getrun(fb_coord_t row, fb_coord_t col, FAR uint8_t *buffer,
+    size_t npixels)
+{
+  FAR uint16_t *dest = (FAR uint16_t*) buffer;
+  int i;
+
+  /* Buffer must be provided and aligned to a 16-bit address boundary */
+  DEBUGASSERT(buffer && ((uintptr_t)buffer & 1) == 0);
+
+  /* Read the run from GRAM. */
+  lcd_setcursor(col, row);
+
+  lcd_gramselect();
+
+  /* dummy read */
+  (void)read_data();
+
+  for (i = 0; i < npixels; i++)
+  {
+    *dest++ = read_data();
+  }
+  return OK;
+}
+
+/**************************************************************************************
+ * Name:  lcd_getvideoinfo
+ *
+ * Description:
+ *   Get information about the LCD video controller configuration.
+ *
+ **************************************************************************************/
+
+static int lcd_getvideoinfo(FAR struct lcd_dev_s *dev,
+    FAR struct fb_videoinfo_s *vinfo)
+{
+  DEBUGASSERT(dev && vinfo);gvdbg("fmt: %d xres: %d yres: %d nplanes: %d\n",
+      g_videoinfo.fmt, g_videoinfo.xres, g_videoinfo.yres, g_videoinfo.nplanes);
+  memcpy(vinfo, &g_videoinfo, sizeof(struct fb_videoinfo_s));
+  return OK;
+}
+
+/**************************************************************************************
+ * Name:  lcd_getplaneinfo
+ *
+ * Description:
+ *   Get information about the configuration of each LCD color plane.
+ *
+ **************************************************************************************/
+
+static int lcd_getplaneinfo(FAR struct lcd_dev_s *dev, unsigned int planeno,
+    FAR struct lcd_planeinfo_s *pinfo)
+{
+  DEBUGASSERT(dev && pinfo && planeno == 0);gvdbg("planeno: %d bpp: %d\n", planeno, g_planeinfo.bpp);
+  memcpy(pinfo, &g_planeinfo, sizeof(struct lcd_planeinfo_s));
+  return OK;
+}
+
+/**************************************************************************************
+ * Name:  lcd_getpower
+ *
+ * Description:
+ *   Get the LCD panel power status (0: full off - CONFIG_LCD_MAXPOWER: full on). On
+ *   backlit LCDs, this setting may correspond to the backlight setting.
+ *
+ **************************************************************************************/
+
+static int lcd_getpower(struct lcd_dev_s *dev)
+{
+  gvdbg("power: %d\n", 0);
+  return g_lcddev.power;
+}
+
+/**************************************************************************************
+ * Name:  lcd_setpower
+ *
+ * Description:
+ *   Enable/disable LCD panel power (0: full off - CONFIG_LCD_MAXPOWER: full on).
+ *   Used here to set pwm duty on timer used for backlight.
+ *
+ **************************************************************************************/
+
+static int lcd_setpower(struct lcd_dev_s *dev, int power)
+{
+  if (g_lcddev.power == power) {
+    return OK;
+  }
+
+  gvdbg("power: %d\n", power);
+  DEBUGASSERT(power <= CONFIG_LCD_MAXPOWER);
+
+  /* Set new power level */
+
+  if (power > 0)
+    {
+#ifdef CONFIG_LCD_BACKLIGHT
+      uint32_t duty;
+
+      /* Calculate the new backlight duty.  It is a fraction of the timer
+       * period based on the ration of the current power setting to the
+       * maximum power setting.
+       */
+      duty = ((uint32_t)LCD_BL_TIMER_PERIOD * (uint32_t)power) / CONFIG_LCD_MAXPOWER;
+      if (duty >= LCD_BL_TIMER_PERIOD)
+        {
+          duty = LCD_BL_TIMER_PERIOD - 1;
+        }
+      gvdbg("PWM duty: %d\n", duty);
+      putreg16((uint16_t)duty, STM32_TIM3_CCR2);
+#endif
+      /* TODO turn the display on */
+    }
+  else
+    {
+      /* FIXME: Turn display off ? */
+      gvdbg("Force PWM to 0\n");
+      putreg16((uint16_t)0, STM32_TIM3_CCR2);
+    }
+  g_lcddev.power = power;
+  return OK;
+}
+
+
+/**************************************************************************************
+ * Name:  lcd_getcontrast
+ *
+ * Description:
+ *   Get the current contrast setting (0-CONFIG_LCD_MAXCONTRAST).
+ *
+ **************************************************************************************/
+
+static int lcd_getcontrast(struct lcd_dev_s *dev)
+{
+  gvdbg("Not implemented\n");
+  return -ENOSYS;
+}
+
+/**************************************************************************************
+ * Name:  lcd_setcontrast
+ *
+ * Description:
+ *   Set LCD panel contrast (0-CONFIG_LCD_MAXCONTRAST).
+ *
+ **************************************************************************************/
+
+static int lcd_setcontrast(struct lcd_dev_s *dev, unsigned int contrast)
+{
+  gvdbg("Not implemented\n");
+  return -ENOSYS;
+}
+
+/**************************************************************************************
+ * Name:  lcd_lcdinitialize
+ *
+ * Description:
+ *   Set LCD panel contrast (0-CONFIG_LCD_MAXCONTRAST).
+ *
+ **************************************************************************************/
+static inline void lcd_initialize(void)
+{
+  /* Display control (GON=1,DTE=0,D[1:0]=01)
+     D[1:0]=01 - Internal display is performed, display is off.
+  */
+  write_reg(0x07, 0x0021);
+
+  /* Oscillator (OSCEN=1) */
+  write_reg(0x00, 0x0001);
+
+  /* Display control (GON=1,DTE=0,D[1:0]=11)
+     D[1:0]=11 - Internal display is performed, display is on.
+  */
+  write_reg(0x07, 0x0023);
+
+  /* Wait 30ms */
+  up_mdelay(30);
+
+  /* Display control (GON=1,DTE=1,D[1:0]=11) */
+  write_reg(0x07, 0x0033);
+
+  /* Power control 1
+   DCT3 DCT2 DCT1 DCT0    BT2 BT1 BT0 -     DC3 DC2 DC1 DC0   AP2 AP1 AP0 -
+   1     0    1    0       1   0   0  0      1   0   1   0     0   1   0  0
+   DCT[3:0] - 1010: fosc/4  (step-up cycle of the step-up circuit for 8-color mode)
+   BT[2:0]  - 100 (step-up factor of the step-up circuit)
+   DC[3:0]  - 1010: fosc/4  (step-up cycle of the step-up circuit for 262k-color mode)
+   AP[2:0]  - 010: Small to medium (amount of current from the stable-current source in internal operational amplifier circuit)
+  */
+  write_reg(0x03, 0xA8A4); /* or 0x0804 ?? */
+
+  /* Power Control 2
+     VRC[2:0] - 000: 5.1v (VCIX2 output voltage)
+   */
+  write_reg(0x0C, 0x0000);
+
+  /* Power Control 3
+     - - - -   - - - -    - - - -   VRH3 VRH2 VRH1 VRH0
+     0 0 0 0   0 0 0 0    0 0 0 0    1    0    0    0
+     VRH[3:0] - 1000: Vref x 2.165  (Set amplitude magnification of VLCD63)
+   */
+  write_reg(0x0D, 0x0008); // or 0x080C ??
+
+  /* power control 4
+     - - VCOMG VDV4  VDV3 VDV2 VDV1 VDV0  - - - -   - - - -
+     0 0   1    0     1    0    0    1    0 0 0 0   0 0 0 0
+     VDV[4:0] - 01001:  VLCD63 x 0.xx (Vcom amplitude)
+     VCOMG - 1 (enable output voltage of VcomL - VDV[4:0])
+   */
+  write_reg(0x0E, 0x2900);
+
+  /* Power Control 5
+    - - - -   - - - -   nOTP - VCM5 VCM4   VCM3 VCM2 VCM1 VCM0
+    0 0 0 0   0 0 0 0     1  0  1    1      1    0    0    0
+    nOTP: 1  - setting of VCM[5:0] becomes valid and voltage of VcomH can be adjusted.
+    VCM[5-0] - 111000:  VLCD63 x 0.xx  (amplify the VcomH voltage 0.35 to 0.99 times the VLCD63 voltage)
+  */
+  write_reg(0x1E, 0x00B8);
+
+  /* Driver Output Control
+     - RL REV CAD   BGR SM TB MUX8   MUX7 MUX6 MUX5 MUX4   MUX3 MUX2 MUX1 MUX0
+     0 0   1   0     1  0  1   1      0    0    1    1      1    1    1    1
+     RL  - 0  RL setting is ignored when display with RAM  (Dmode[1:0] = 00).
+     REV - 1  Reverse source output level
+     CAD - 0  Cs on Common
+     BGR - 1  BGR  (Selects the order from RGB to BGR in writing 18-bit pixel data in the GDDRAM)
+     SM  - 0  (Gate scan sequence)
+     TB  - 1  (output shift direction of the gate driver)
+     MUX[8:0] - 100111111 (319)  (number of lines for the LCD driver)
+  */
+  write_reg(0x01, 0x2B3F);
+
+  /* LCD-Driving-Waveform Control
+     - - - FLD   ENWS B/C EOR WSMD   NW7 NW6 NW5 NW4   NW3 NW2 NW1 NW0
+     0 0 0  0     0    1   1   0      0   0   0   0     0   0   0   0
+     FLD - 0  ?
+     ENWS- 0  (disable WSYNC output pin  -> HiZ)
+     B/C - 1  (When B/C = 1, a N-line inversion waveform is generated and alternates in a N-line equals to NW[7:0]+1)
+     EOR - 1
+     WSMD- 0
+     NW[7:0] - 0  Specify the number of lines that will alternate at the N-line inversion setting (if B/C = 1).
+  */
+  /* Set FLD ? */
+  write_reg(0x02, 0x0600);
+
+  /* Exit sleep mode */
+  write_reg(0x10, 0x0000);
+
+  /*  Entry Mode
+     VSMode DFM1 DFM0 TRANS   OEDef WMode DMode1 DMode0   TY1 TY0 ID1 ID0    AM LG2 LG1 LG0
+       0     1    1     0      0      0     0      0       0   1   1   1     0   0   0   0
+     VSMode - 0   When VSMode = 1 at DMode[1:0] = “00”, the frame frequency will be dependent on VSYNC.
+     DFM[1:0] - 11 (65k color mode selected)
+     TRANS - 0  (if TRANS = 1, transparent display is allowed during DMode[1:0] = “1x”)
+     0EDef - 0  (display window is defined by R4Eh and R4Fh)
+     WMode - 0  (Normal data bus)
+     DMode[1:0] - 00  (data display from RAM data)
+     TY[1:0] - 01  (type B.  Used for 262k color mode only)
+     ID[1:0] - 11  (address counter auto incremented by 1, horizontal & vertical)
+     AM - 0  Horizontal (direction of the address counter update after data are written to the GDDRAM)
+     LG[2:0] - 000  (operation to perform according to GDRAM compare registers ?)
+  */
+#if defined(CONFIG_LCD_PORTRAIT)
+  write_reg(0x11, 0x6070);
+#elif defined(CONFIG_LCD_RPORTRAIT)
+  /* ID[1:0] - 00  (address counter auto decremented by 1, horizontal & vertical) */
+  write_reg(0x11, 0x6840);
+#elif defined(CONFIG_LCD_LANDSCAPE)
+  /* ID[1:0] - 10  (address counter auto decremented by 1, horizontal & vertical)
+     AM - 1   Vertical direction
+  */
+  write_reg(0x11, 0x6068);
+#else
+#error "LCD orientation not supported"
+#endif
+
+  /* Compare register  (unused ?) */
+  write_reg(0x05, 0x0000);
+  write_reg(0x06, 0x0000);
+
+  /* Horizontal Porch
+     XL7 XL6 XL5 XL4 XL3 XL2 IB9 XL1   HBP7 HBP6 HBP5 HBP4 HBP3 HBP2 HBP1 HBP0
+     XL[7:0] - 0xEF (239)  (Number of valid pixel per line is equal to XL[7:0] + 1)
+     HBP[7:0] - 0x1C (28)  30 dot clocks  (delay period from falling edge of HSYNC signal to first valid data)
+  */
+  write_reg(0x16, 0xEF1C);
+
+  /* Vertical Porch */
+  write_reg(0x17, 0x0003);
+
+  /* Display control
+     - - - PT1    PT0 VLE2 VLE1 SPT    - - GON DTE    CM - D1 D0
+     0 0 0 0       0   0    0    1     0 0  1   1     0  0 1  1
+     VLE[2:1]: 00  (When VLE1 = 1 or VLE2 = 1, vertical scroll performed in the 1st screen by taking data VL17-0 in R41h
+               register. When VLE1 = 1 and VLE2 = 1, a vertical scroll is performed in the 1st and 2nd screen by VL1[8:0] and VL2[8:0])
+     SPT: 1  (When SPT = “1”, the 2-division LCD drive is performed.
+     CM:  0  (8-color mode setting  0=disabled,  1=enabled)
+     D[1:0]: 11
+  */
+  write_reg(0x07, 0x0133);
+
+  /* Frame Cycle Control */
+  write_reg(0x0B, 0x0000);
+
+  /* Gate Scan Position */
+  /* write_reg(0x0F, 0x0000); // Default value */
+
+  /* Vertical Scroll Control */
+  write_reg(0x41, 0x0000);
+  write_reg(0x42, 0x0000);
+
+  /* 1st Screen driving position
+     driving start position for the first screen in a line unit. (0)
+  */
+  write_reg(0x48, 0x0000);
+  /* driving end position for the first screen in a line unit. (319) */
+  write_reg(0x49, 0x013F);
+
+  /* 2nd Screen driving position  (unused) */
+  write_reg(0x4A, 0x0000);
+  write_reg(0x4B, 0x0000);
+
+  /* start/end positions of the window address in the horizontal direction */
+  write_reg(0x44, 0xEF00);
+
+  /* start/end positions of the window address in the vertical direction */
+  /*  write_reg(0x45, 0x0000);  // Default value
+      write_reg(0x46, 0x013F);  // Default value
+  */
+
+  /* Gamma Control */
+  write_reg(0x0030, 0x0707);
+  write_reg(0x0031, 0x0204);
+  write_reg(0x0032, 0x0204);
+  write_reg(0x0033, 0x0502);
+  write_reg(0x0034, 0x0507);
+  write_reg(0x0035, 0x0204);
+  write_reg(0x0036, 0x0204);
+  write_reg(0x0037, 0x0502);
+  write_reg(0x003A, 0x0302);
+  write_reg(0x003B, 0x0302);
+
+  /* RAM write data mask  (unused)
+      write_reg(0x23, 0x0000);  // Default value
+      write_reg(0x24, 0x0000);  // Default value
+  */
+
+  /* Setting R28h as 0x0006 is required before setting R25h and R29h registers.*/
+
+  write_reg(0x28, 0x0006);
+
+  /* Frame Frequency Control (R25h)
+     OSC3 OSC2 OSC1 OSC0  - - - -   - - - -   - - - -
+       1    1    1    0   0 0 0 0   0 0 0 0   0 0 0 0
+     OSC[3:0]:  1110   Corresponding frame freq: 80Hz
+  */
+  write_reg(0x25, 0xE000);  /* (Default value = 8000h) */
+}
+
+/**************************************************************************************
+ * Name:  lcd_backlight
+ *
+ * Description:
+ *   The LCD backlight is driven from PB.5 which must be configured as TIM3
+ *   CH2.  TIM3 must then be configured to pwm output on PB.5; the duty
+ *   of the clock determines the backlight level.
+ *
+ **************************************************************************************/
+
+#ifdef CONFIG_LCD_BACKLIGHT
+
+#ifndef CONFIG_STM32_TIM3_PARTIAL_REMAP
+#  error CONFIG_STM32_TIM3_PARTIAL_REMAP must be set (to have TIM3 CH2 on pin B.5)
+#endif
+
+static void lcd_backlight(void)
+{
+  uint16_t ccmr;
+  uint16_t ccer;
+  uint16_t cr2;
+
+  /* Configure PB5 as TIM3 CH2 output */
+  stm32_configgpio(GPIO_TIM3_CH2OUT);
+
+  /* Enabled timer 3 clocking */
+  modifyreg32(STM32_RCC_APB1ENR, 0, RCC_APB1ENR_TIM3EN);
+
+  /* Reset timer 3 */
+
+  modifyreg32(STM32_RCC_APB1RSTR, 0, RCC_APB1RSTR_TIM3RST);
+  modifyreg32(STM32_RCC_APB1RSTR, RCC_APB1RSTR_TIM3RST, 0);
+
+  /* Reset the Counter Mode and set the clock division */
+  putreg16(0, STM32_TIM3_CR1);
+
+  /* Set the Autoreload value */
+  putreg16(LCD_BL_TIMER_PERIOD, STM32_TIM3_ARR);
+
+  /* Set the Prescaler value */
+
+  putreg16(0, STM32_TIM3_PSC);
+
+  /* Generate an update event to reload the Prescaler value immediatly */
+
+  putreg16(ATIM_EGR_UG, STM32_TIM3_EGR);
+
+  /* Disable the Channel 2 */
+
+  ccer  = getreg16(STM32_TIM3_CCER);
+  ccer &= ~ATIM_CCER_CC2E;
+  putreg16(ccer, STM32_TIM3_CCER);
+
+  /* Get the TIM3 CR2 register value */
+  cr2  = getreg16(STM32_TIM3_CR2);
+
+  /* Select the Output Compare Mode Bits */
+
+  ccmr  = getreg16(STM32_TIM3_CCMR1);
+  ccmr &= ATIM_CCMR1_OC2M_MASK;
+  ccmr |= (ATIM_CCMR_MODE_PWM1 << ATIM_CCMR1_OC2M_SHIFT);
+
+  /* Set the capture compare register value (50% duty) */
+  // FIXME should be set to 0  (appl needs to call setpower to change it)
+  g_lcddev.power = (CONFIG_LCD_MAXPOWER + 1) / 2;
+  putreg16((LCD_BL_TIMER_PERIOD + 1) / 2, STM32_TIM3_CCR2);
+
+  /* Select the output polarity level == HIGH */
+  ccer &= !ATIM_CCER_CC2P;
+
+  /* Enable channel 2*/
+  ccer |= ATIM_CCER_CC2E;
+
+  /* Write the timer configuration */
+
+  putreg16(ccmr, STM32_TIM3_CCMR1);
+  putreg16(ccer, STM32_TIM3_CCER);
+
+  /* Set the auto preload enable bit */
+
+  modifyreg16(STM32_TIM3_CR1, 0, ATIM_CR1_ARPE);
+
+  /* Enable Backlight Timer !!!!*/
+  modifyreg16(STM32_TIM3_CR1, 0, ATIM_CR1_CEN);
+
+  /* Dump timer3 registers */
+  lcddbg("APB1ENR: %08x\n", getreg32(STM32_RCC_APB1ENR));
+  lcddbg("CR1:     %04x\n", getreg32(STM32_TIM3_CR1));
+  lcddbg("CR2:     %04x\n", getreg32(STM32_TIM3_CR2));
+  lcddbg("SMCR:    %04x\n", getreg32(STM32_TIM3_SMCR));
+  lcddbg("DIER:    %04x\n", getreg32(STM32_TIM3_DIER));
+  lcddbg("SR:      %04x\n", getreg32(STM32_TIM3_SR));
+  lcddbg("EGR:     %04x\n", getreg32(STM32_TIM3_EGR));
+  lcddbg("CCMR1:   %04x\n", getreg32(STM32_TIM3_CCMR1));
+  lcddbg("CCMR2:   %04x\n", getreg32(STM32_TIM3_CCMR2));
+  lcddbg("CCER:    %04x\n", getreg32(STM32_TIM3_CCER));
+  lcddbg("CNT:     %04x\n", getreg32(STM32_TIM3_CNT));
+  lcddbg("PSC:     %04x\n", getreg32(STM32_TIM3_PSC));
+  lcddbg("ARR:     %04x\n", getreg32(STM32_TIM3_ARR));
+  lcddbg("CCR1:    %04x\n", getreg32(STM32_TIM3_CCR1));
+  lcddbg("CCR2:    %04x\n", getreg32(STM32_TIM3_CCR2));
+  lcddbg("CCR3:    %04x\n", getreg32(STM32_TIM3_CCR3));
+  lcddbg("CCR4:    %04x\n", getreg32(STM32_TIM3_CCR4));
+  lcddbg("CCR4:    %04x\n", getreg32(STM32_TIM3_CCR4));
+  lcddbg("CCR4:    %04x\n", getreg32(STM32_TIM3_CCR4));
+  lcddbg("DMAR:    %04x\n", getreg32(STM32_TIM3_DMAR));
+}
+#endif
+
+/**************************************************************************************
+ * Public Functions
+ **************************************************************************************/
+
+/**************************************************************************************
+ * Name:  up_lcdinitialize
+ *
+ * Description:
+ *   Initialize the LCD video hardware.  The initial state of the LCD is fully
+ *   initialized, display memory cleared, and the LCD ready to use, but with the power
+ *   setting at 0 (full off).
+ *
+ **************************************************************************************/
+
+int up_lcdinitialize(void)
+{
+  unsigned short id;
+
+  gvdbg("Initializing\n");
+
+  /* Configure GPIO pins and configure the FSMC to support the LCD */
+  stm32_selectlcd();
+
+  /* Delay required here */
+
+  up_mdelay(50);
+
+  /* Check model id */
+
+  id=read_reg(0x0);
+  if (id != SSD1289_ID) {
+    /* Not a SSD1289 ? */
+    gdbg("up_lcdinitialize: LCD ctrl is not a SSD1289");
+    return ERROR;
+  }
+
+  /* Configure and enable LCD */
+
+  lcd_initialize();
+
+  /* Clear the display (setting it to the color 0=black) */
+
+  lcd_clear(0);
+
+  /* Configure the backlight */
+
+  lcd_backlight();
+  return OK;
+}
+
+/**************************************************************************************
+ * Name:  up_lcdgetdev
+ *
+ * Description:
+ *   Return a a reference to the LCD object for the specified LCD.  This allows support
+ *   for multiple LCD devices.
+ *
+ **************************************************************************************/
+
+FAR struct lcd_dev_s *up_lcdgetdev(int lcddev)
+{
+  DEBUGASSERT(lcddev == 0);
+  return &g_lcddev.dev;
+}
+
+/**************************************************************************************
+ * Name:  up_lcduninitialize
+ *
+ * Description:
+ *   Un-initialize the LCD support
+ *
+ **************************************************************************************/
+
+void up_lcduninitialize(void)
+{
+  lcd_setpower(&g_lcddev.dev, 0);
+  stm32_deselectlcd();
+}
+
+/**************************************************************************************
+ * Name:  lcd_clear
+ *
+ * Description:
+ *   Fill the LCD ctrl memory with given color
+ *
+ **************************************************************************************/
+
+void lcd_clear(uint16_t color)
+{
+  uint32_t index;
+  lcd_setcursor(0, 0);
+  lcd_gramselect(); /* Prepare to write GRAM */
+  for (index = 0; index < LCD_XRES * LCD_YRES; index++)
+  {
+    write_data(color);
+  }
+}
diff --git a/nuttx/configs/hymini-stm32v/src/ssd1289.h b/nuttx/configs/hymini-stm32v/src/ssd1289.h
new file mode 100644
index 000000000..6f81361fe
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/ssd1289.h
@@ -0,0 +1,55 @@
+/************************************************************************************
+ * configs/hymini-stm32v/src/ssd1289.h
+ * arch/arm/src/board/ssd1289.h
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *           Laurent Latil <laurent@latil.nom.fr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+#ifndef SSD1289_H_
+#define SSD1289_H_
+
+#include <nuttx/lcd/lcd.h>
+
+/* LCD IDs */
+#define SSD1289_ID          0x8989
+
+struct ssd1289_dev_s
+{
+  /* Publicly visible device structure */
+  struct lcd_dev_s dev;
+
+  /* Private LCD-specific information follows */
+  uint8_t power; /* Current power setting */
+};
+
+#endif /* SSD1289_H_ */
diff --git a/nuttx/configs/hymini-stm32v/src/up_boot.c b/nuttx/configs/hymini-stm32v/src/up_boot.c
new file mode 100644
index 000000000..4b48e0b57
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_boot.c
@@ -0,0 +1,103 @@
+/************************************************************************************

+ * configs/hymini-stm32v/src/up_boot.c

+ * arch/arm/src/board/up_boot.c

+ *

+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.

+ *   Author: Gregory Nutt <gnutt@nuttx.org>

+ *           Laurent Latil <laurent@latil.nom.fr>

+ *

+ * Redistribution and use in source and binary forms, with or without

+ * modification, are permitted provided that the following conditions

+ * are met:

+ *

+ * 1. Redistributions of source code must retain the above copyright

+ *    notice, this list of conditions and the following disclaimer.

+ * 2. Redistributions in binary form must reproduce the above copyright

+ *    notice, this list of conditions and the following disclaimer in

+ *    the documentation and/or other materials provided with the

+ *    distribution.

+ * 3. Neither the name NuttX nor the names of its contributors may be

+ *    used to endorse or promote products derived from this software

+ *    without specific prior written permission.

+ *

+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS

+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT

+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE

+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,

+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS

+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

+ * POSSIBILITY OF SUCH DAMAGE.

+ *

+ ************************************************************************************/

+

+/************************************************************************************

+ * Included Files

+ ************************************************************************************/

+

+#include <nuttx/config.h>

+#include <nuttx/spi.h>

+#include <debug.h>

+

+#include <arch/board/board.h>

+

+#include "up_arch.h"

+#include "hymini_stm32v-internal.h"

+

+/************************************************************************************

+ * Definitions

+ ************************************************************************************/

+

+/************************************************************************************

+ * Private Data

+ ************************************************************************************/

+

+/************************************************************************************

+ * Public Functions

+ ************************************************************************************/

+

+/************************************************************************************

+ * Name: stm32_boardinitialize

+ *

+ * Description:

+ *   All STM32 architectures must provide the following entry point.  This entry point

+ *   is called early in the initialization -- after all memory has been configured

+ *   and mapped but before any devices have been initialized.

+ *

+ ************************************************************************************/

+

+void stm32_boardinitialize(void)

+{

+  /* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function

+   * stm32_spiinitialize() has been brought into the link.

+   */

+

+#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2)

+  if (stm32_spiinitialize)

+    {

+      stm32_spiinitialize();

+    }

+#endif

+

+   /* Initialize USB is 1) USBDEV is selected, 2) the USB controller is not

+    * disabled, and 3) the weak function stm32_usbinitialize() has been brought

+    * into the build.

+    */

+

+#if defined(CONFIG_USBDEV) && defined(CONFIG_STM32_USB)

+  if (stm32_usbinitialize)

+    {

+      stm32_usbinitialize();

+    }

+#endif

+

+  /* Configure on-board LEDs if LED support has been selected. */

+

+#ifdef CONFIG_ARCH_LEDS

+  up_ledinit();

+#endif

+}

diff --git a/nuttx/configs/hymini-stm32v/src/up_buttons.c b/nuttx/configs/hymini-stm32v/src/up_buttons.c
new file mode 100644
index 000000000..c3ea0b821
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_buttons.c
@@ -0,0 +1,159 @@
+/****************************************************************************
+ * configs/hymini-stm32v/src/up_buttons.c
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+
+#include <arch/board/board.h>
+#include "hymini_stm32v-internal.h"
+
+#ifdef CONFIG_ARCH_BUTTONS
+
+/****************************************************************************
+ * Definitions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+/* Pin configuration for each HY-mini button.  This array is indexed by
+ * the BUTTON_* definitions in board.h
+ */
+
+//static const uint16_t g_buttons[NUM_BUTTONS] =
+//  {
+//    GPIO_BTN_KEYA, GPIO_BTN_KEYB
+//  };
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: up_buttoninit
+ *
+ * Description:
+ *   up_buttoninit() must be called to initialize button resources.  After
+ *   that, up_buttons() may be called to collect the current state of all
+ *   buttons or up_irqbutton() may be called to register button interrupt
+ *   handlers.
+ *
+ ****************************************************************************/
+
+void up_buttoninit(void)
+  {
+    stm32_configgpio(GPIO_BTN_KEYA);
+    stm32_configgpio(GPIO_BTN_KEYB);
+  }
+
+/****************************************************************************
+ * Name: up_buttons
+ ****************************************************************************/
+
+uint8_t up_buttons(void)
+  {
+    uint8_t ret = 0;
+    bool pinValue;
+
+    /* Check that state of each key */
+
+    /* Pin is pulled up */
+    pinValue = stm32_gpioread(GPIO_BTN_KEYA);
+    if (!pinValue)
+      {
+        // Button pressed
+        ret = 1 << BUTTON_KEYA;
+      }
+
+    /* Pin is pulled down */
+    pinValue = stm32_gpioread(GPIO_BTN_KEYB);
+    if (pinValue)
+      {
+        // Button pressed
+        ret |= 1 << BUTTON_KEYB;
+      }
+    return ret;
+  }
+
+/************************************************************************************
+ * Button support.
+ *
+ * Description:
+ *   up_buttoninit() must be called to initialize button resources.  After
+ *   that, up_buttons() may be called to collect the current state of all
+ *   buttons or up_irqbutton() may be called to register button interrupt
+ *   handlers.
+ *
+ *   After up_buttoninit() has been called, up_buttons() may be called to
+ *   collect the state of all buttons.  up_buttons() returns an 8-bit bit set
+ *   with each bit associated with a button.  See the BUTTON_*_BIT and JOYSTICK_*_BIT
+ *   definitions in board.h for the meaning of each bit.
+ *
+ *   up_irqbutton() may be called to register an interrupt handler that will
+ *   be called when a button is depressed or released.  The ID value is a
+ *   button enumeration value that uniquely identifies a button resource. See the
+ *   BUTTON_* definitions in board.h for the meaning of enumeration
+ *   value.  The previous interrupt handler address is returned (so that it may
+ *   restored, if so desired).
+ *
+ ************************************************************************************/
+
+#ifdef CONFIG_ARCH_IRQBUTTONS
+xcpt_t up_irqbutton(int id, xcpt_t irqhandler)
+  {
+    xcpt_t oldhandler = NULL;
+    uint32_t pinset = GPIO_BTN_KEYA;
+
+    if (id == 1)
+      {
+        pinset = GPIO_BTN_KEYB;
+      }
+    if (id < 2)
+      {
+        oldhandler = stm32_gpiosetevent(pinset, true, true, true, irqhandler);
+      }
+    return oldhandler;
+  }
+#endif
+#endif /* CONFIG_ARCH_BUTTONS */
diff --git a/nuttx/configs/hymini-stm32v/src/up_leds.c b/nuttx/configs/hymini-stm32v/src/up_leds.c
new file mode 100644
index 000000000..3cd0d44bd
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_leds.c
@@ -0,0 +1,241 @@
+/****************************************************************************
+ * configs/hymini-stm32v/src/up_leds.c
+ * arch/arm/src/board/up_leds.c
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *           Laurent Latil <laurent@latil.nom.fr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <arch/board/board.h>
+
+#include "chip.h"
+#include "up_arch.h"
+#include "up_internal.h"
+#include "stm32_internal.h"
+#include "hymini_stm32v-internal.h"
+
+/****************************************************************************
+ * Definitions
+ ****************************************************************************/
+
+/* Enables debug output from this file (needs CONFIG_DEBUG with
+ * CONFIG_DEBUG_VERBOSE too)
+ */
+
+#undef LED_DEBUG  /* Define to enable debug */
+
+#ifdef LED_DEBUG
+#  define leddbg  lldbg
+#  define ledvdbg llvdbg
+#else
+#  define leddbg(x...)
+#  define ledvdbg(x...)
+#endif
+
+/* The following definitions map the encoded LED setting to GPIO settings */
+
+#define HYMINI_STM32_LED1     (1 << 0)
+#define HYMINI_STM32_LED2     (1 << 1)
+
+#define ON_SETBITS_SHIFT  (0)
+#define ON_CLRBITS_SHIFT  (4)
+#define OFF_SETBITS_SHIFT (8)
+#define OFF_CLRBITS_SHIFT (12)
+
+#define ON_BITS(v)        ((v) & 0xff)
+#define OFF_BITS(v)       (((v) >> 8) & 0x0ff)
+#define SETBITS(b)        ((b) & 0x0f)
+#define CLRBITS(b)        (((b) >> 4) & 0x0f)
+
+#define ON_SETBITS(v)     (SETBITS(ON_BITS(v))
+#define ON_CLRBITS(v)     (CLRBITS(ON_BITS(v))
+#define OFF_SETBITS(v)    (SETBITS(OFF_BITS(v))
+#define OFF_CLRBITS(v)    (CLRBITS(OFF_BITS(v))
+
+/* On: !LED1 + !LED2   Off: - */
+#define LED_STARTED_ON_SETBITS       ((0) << ON_SETBITS_SHIFT)
+#define LED_STARTED_ON_CLRBITS       ((HYMINI_STM32_LED1|HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
+#define LED_STARTED_OFF_SETBITS      (0 << OFF_SETBITS_SHIFT)
+#define LED_STARTED_OFF_CLRBITS      (0 << OFF_CLRBITS_SHIFT)
+
+/* On: LED1+!LED2   Off: N/A */
+#define LED_HEAPALLOCATE_ON_SETBITS  ((HYMINI_STM32_LED1) << ON_SETBITS_SHIFT)
+#define LED_HEAPALLOCATE_ON_CLRBITS  ((HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
+#define LED_HEAPALLOCATE_OFF_SETBITS (0)
+#define LED_HEAPALLOCATE_OFF_CLRBITS (0)
+
+/* On: LED2+!LED1   Off: N/A */
+#define LED_IRQSENABLED_ON_SETBITS   ((HYMINI_STM32_LED2) << ON_SETBITS_SHIFT)
+#define LED_IRQSENABLED_ON_CLRBITS   ((HYMINI_STM32_LED1) << ON_CLRBITS_SHIFT)
+#define LED_IRQSENABLED_OFF_SETBITS  (0)
+#define LED_IRQSENABLED_OFF_CLRBITS  (0)
+
+/* On: LED1+!LED2   Off: N/A */
+#define LED_STACKCREATED_ON_SETBITS  ((HYMINI_STM32_LED1) << ON_SETBITS_SHIFT)
+#define LED_STACKCREATED_ON_CLRBITS  ((HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
+#define LED_STACKCREATED_OFF_SETBITS (0)
+#define LED_STACKCREATED_OFF_CLRBITS (0)
+
+/* On: !LED1   Off: LED1 */
+#define LED_INIRQ_ON_SETBITS         ((0) << ON_SETBITS_SHIFT)
+#define LED_INIRQ_ON_CLRBITS         ((HYMINI_STM32_LED1) << ON_CLRBITS_SHIFT)
+#define LED_INIRQ_OFF_SETBITS        ((HYMINI_STM32_LED1) << OFF_SETBITS_SHIFT)
+#define LED_INIRQ_OFF_CLRBITS        ((0) << OFF_CLRBITS_SHIFT)
+
+/* On: LED2   Off: !LED2 */
+#define LED_SIGNAL_ON_SETBITS        ((HYMINI_STM32_LED2) << ON_SETBITS_SHIFT)
+#define LED_SIGNAL_ON_CLRBITS        ((0) << ON_CLRBITS_SHIFT)
+#define LED_SIGNAL_OFF_SETBITS       ((0) << OFF_SETBITS_SHIFT)
+#define LED_SIGNAL_OFF_CLRBITS       ((HYMINI_STM32_LED2) << OFF_CLRBITS_SHIFT)
+
+/* On: LED1+LED2   Off: - */
+#define LED_ASSERTION_ON_SETBITS     ((HYMINI_STM32_LED2|HYMINI_STM32_LED2) << ON_SETBITS_SHIFT)
+#define LED_ASSERTION_ON_CLRBITS     ((0) << ON_CLRBITS_SHIFT)
+#define LED_ASSERTION_OFF_SETBITS    ((0) << OFF_SETBITS_SHIFT)
+#define LED_ASSERTION_OFF_CLRBITS    ((0) << OFF_CLRBITS_SHIFT)
+
+/* On: LED1   Off: LED2 */
+#define LED_PANIC_ON_SETBITS         ((HYMINI_STM32_LED1) << ON_SETBITS_SHIFT)
+#define LED_PANIC_ON_CLRBITS         ((HYMINI_STM32_LED2) << ON_CLRBITS_SHIFT)
+#define LED_PANIC_OFF_SETBITS        ((HYMINI_STM32_LED2) << OFF_SETBITS_SHIFT)
+#define LED_PANIC_OFF_CLRBITS        ((HYMINI_STM32_LED1) << OFF_CLRBITS_SHIFT)
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+static const uint16_t g_ledbits[8] =
+{ (LED_STARTED_ON_SETBITS | LED_STARTED_ON_CLRBITS | LED_STARTED_OFF_SETBITS
+    | LED_STARTED_OFF_CLRBITS),
+
+(LED_HEAPALLOCATE_ON_SETBITS | LED_HEAPALLOCATE_ON_CLRBITS
+    | LED_HEAPALLOCATE_OFF_SETBITS | LED_HEAPALLOCATE_OFF_CLRBITS),
+
+(LED_IRQSENABLED_ON_SETBITS | LED_IRQSENABLED_ON_CLRBITS
+    | LED_IRQSENABLED_OFF_SETBITS | LED_IRQSENABLED_OFF_CLRBITS),
+
+(LED_STACKCREATED_ON_SETBITS | LED_STACKCREATED_ON_CLRBITS
+    | LED_STACKCREATED_OFF_SETBITS | LED_STACKCREATED_OFF_CLRBITS),
+
+(LED_INIRQ_ON_SETBITS | LED_INIRQ_ON_CLRBITS | LED_INIRQ_OFF_SETBITS
+    | LED_INIRQ_OFF_CLRBITS),
+
+(LED_SIGNAL_ON_SETBITS | LED_SIGNAL_ON_CLRBITS | LED_SIGNAL_OFF_SETBITS
+    | LED_SIGNAL_OFF_CLRBITS),
+
+(LED_ASSERTION_ON_SETBITS | LED_ASSERTION_ON_CLRBITS | LED_ASSERTION_OFF_SETBITS
+    | LED_ASSERTION_OFF_CLRBITS),
+
+(LED_PANIC_ON_SETBITS | LED_PANIC_ON_CLRBITS | LED_PANIC_OFF_SETBITS
+    | LED_PANIC_OFF_CLRBITS) };
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+static inline void led_clrbits(unsigned int clrbits)
+{
+  if ((clrbits & HYMINI_STM32_LED1) != 0)
+  {
+    stm32_gpiowrite(GPIO_LED1, false);
+  }
+
+  if ((clrbits & HYMINI_STM32_LED2) != 0)
+  {
+    stm32_gpiowrite(GPIO_LED2, false);
+  }
+}
+
+static inline void led_setbits(unsigned int setbits)
+{
+  if ((setbits & HYMINI_STM32_LED1) != 0)
+  {
+    stm32_gpiowrite(GPIO_LED1, true);
+  }
+
+  if ((setbits & HYMINI_STM32_LED2) != 0)
+  {
+    stm32_gpiowrite(GPIO_LED2, true);
+  }
+}
+
+static void led_setonoff(unsigned int bits)
+{
+  led_clrbits(CLRBITS(bits));
+  led_setbits(SETBITS(bits));
+}
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: up_ledinit
+ ****************************************************************************/
+
+#ifdef CONFIG_ARCH_LEDS
+void up_ledinit(void)
+{
+  /* Configure LED1 & LED2 GPIOs for output */
+  stm32_configgpio(GPIO_LED1);
+  stm32_configgpio(GPIO_LED2);
+}
+
+/****************************************************************************
+ * Name: up_ledon
+ ****************************************************************************/
+
+void up_ledon(int led)
+{
+  led_setonoff(ON_BITS(g_ledbits[led]));
+}
+
+/****************************************************************************
+ * Name: up_ledoff
+ ****************************************************************************/
+
+void up_ledoff(int led)
+{
+  led_setonoff(OFF_BITS(g_ledbits[led]));
+}
+
+#endif /* CONFIG_ARCH_LEDS */
diff --git a/nuttx/configs/hymini-stm32v/src/up_nsh.c b/nuttx/configs/hymini-stm32v/src/up_nsh.c
new file mode 100644
index 000000000..d7c4605ac
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_nsh.c
@@ -0,0 +1,182 @@
+/****************************************************************************
+ * config/hymini-stm32v/src/up_nsh.c
+ * arch/arm/src/board/up_nsh.c
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <debug.h>
+#include <errno.h>
+
+#ifdef CONFIG_STM32_SPI1
+#  include <nuttx/spi.h>
+#  include <nuttx/mtd.h>
+#endif
+
+#ifdef CONFIG_STM32_SDIO
+#  include <nuttx/sdio.h>
+#  include <nuttx/mmcsd.h>
+#endif
+
+#include "stm32_internal.h"
+#include "hymini_stm32v-internal.h"
+
+/****************************************************************************
+ * Pre-Processor Definitions
+ ****************************************************************************/
+
+/* Configuration ************************************************************/
+
+/* For now, don't build in any SPI1 support -- NSH is not using it */
+
+#undef CONFIG_STM32_SPI1
+
+
+/* PORT and SLOT number probably depend on the board configuration */
+
+#ifdef CONFIG_ARCH_BOARD_HYMINI_STM32V
+#  define CONFIG_NSH_HAVEUSBDEV 1
+#  define CONFIG_NSH_HAVEMMCSD  1
+#  if defined(CONFIG_NSH_MMCSDSLOTNO) && CONFIG_NSH_MMCSDSLOTNO != 0
+#    error "Only one MMC/SD slot"
+#    undef CONFIG_NSH_MMCSDSLOTNO
+#  endif
+#  ifndef CONFIG_NSH_MMCSDSLOTNO
+#    define CONFIG_NSH_MMCSDSLOTNO 0
+#  endif
+#else
+   /* Add configuration for new STM32 boards here */
+#  error "Unrecognized STM32 board"
+#  undef CONFIG_NSH_HAVEUSBDEV
+#  undef CONFIG_NSH_HAVEMMCSD
+#endif
+
+/* Can't support USB features if USB is not enabled */
+
+#ifndef CONFIG_USBDEV
+#  undef CONFIG_NSH_HAVEUSBDEV
+#endif
+
+/* Can't support MMC/SD features if mountpoints are disabled or if SDIO support
+ * is not enabled.
+ */
+
+#if defined(CONFIG_DISABLE_MOUNTPOINT) || !defined(CONFIG_STM32_SDIO)
+#  undef CONFIG_NSH_HAVEMMCSD
+#endif
+
+#ifndef CONFIG_NSH_MMCSDMINOR
+#  define CONFIG_NSH_MMCSDMINOR 0
+#endif
+
+/* Debug ********************************************************************/
+
+#ifdef CONFIG_CPP_HAVE_VARARGS
+#  ifdef CONFIG_DEBUG
+#    define message(...) lib_lowprintf(__VA_ARGS__)
+#  else
+#    define message(...) printf(__VA_ARGS__)
+#  endif
+#else
+#  ifdef CONFIG_DEBUG
+#    define message lib_lowprintf
+#  else
+#    define message printf
+#  endif
+#endif
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: nsh_archinitialize
+ *
+ * Description:
+ *   Perform architecture specific initialization
+ *
+ ****************************************************************************/
+
+int nsh_archinitialize(void)
+{
+#ifdef CONFIG_NSH_HAVEMMCSD
+  FAR struct sdio_dev_s *sdio;
+  int ret;
+
+  /* Card detect */
+  bool cd_status;
+#endif
+
+  /* Mount the SDIO-based MMC/SD block driver */
+
+#ifdef CONFIG_NSH_HAVEMMCSD
+  /* First, get an instance of the SDIO interface */
+
+  message("nsh_archinitialize: Initializing SDIO slot %d\n",
+          CONFIG_NSH_MMCSDSLOTNO);
+  sdio = sdio_initialize(CONFIG_NSH_MMCSDSLOTNO);
+  if (!sdio)
+    {
+      message("nsh_archinitialize: Failed to initialize SDIO slot %d\n",
+              CONFIG_NSH_MMCSDSLOTNO);
+      return -ENODEV;
+    }
+
+  /* Now bind the SDIO interface to the MMC/SD driver */
+
+  message("nsh_archinitialize: Bind SDIO to the MMC/SD driver, minor=%d\n",
+          CONFIG_NSH_MMCSDMINOR);
+  ret = mmcsd_slotinitialize(CONFIG_NSH_MMCSDMINOR, sdio);
+  if (ret != OK)
+    {
+      message("nsh_archinitialize: Failed to bind SDIO to the MMC/SD driver: %d\n", ret);
+      return ret;
+    }
+  message("nsh_archinitialize: Successfully bound SDIO to the MMC/SD driver\n");
+  
+  /* Use SD card detect pin to check if a card is inserted */
+
+  cd_status = !stm32_gpioread(GPIO_SD_CD);
+  message("Card detect : %hhu", cd_status);
+
+  sdio_mediachange(sdio, cd_status);
+#endif
+  return OK;
+}
diff --git a/nuttx/configs/hymini-stm32v/src/up_spi.c b/nuttx/configs/hymini-stm32v/src/up_spi.c
new file mode 100644
index 000000000..631c70ce9
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_spi.c
@@ -0,0 +1,179 @@
+/************************************************************************************
+ * configs/hymini-stm32v/src/up_spi.c
+ * arch/arm/src/board/up_spi.c
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *           Laurent Latil <laurent@latil.nom.fr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <nuttx/spi.h>
+#include <arch/board/board.h>
+
+#include "up_arch.h"
+#include "chip.h"
+#include "stm32_internal.h"
+#include "hymini_stm32v-internal.h"
+
+#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2)
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/* Enables debug output from this file (needs CONFIG_DEBUG too) */
+
+#define SPI_DEBUG   /* Define to enable debug */
+#define SPI_VERBOSE /* Define to enable verbose debug */
+
+#ifdef SPI_DEBUG
+#  define spidbg  lldbg
+#  ifdef SPI_VERBOSE
+#    define spivdbg lldbg
+#  else
+#    define spivdbg(x...)
+#  endif
+#else
+#  undef SPI_VERBOSE
+#  define spidbg(x...)
+#  define spivdbg(x...)
+#endif
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the HY-MiniSTM32 board.
+ *
+ ************************************************************************************/
+
+void stm32_spiinitialize(void)
+{
+  /* NOTE: Clocking for SPI1 and/or SPI2 was already provided in stm32_rcc.c.
+   *       Configurations of SPI pins is performed in stm32_spi.c.
+   *       Here, we only initialize chip select pins unique to the board
+   *       architecture.
+   */
+
+#ifdef CONFIG_STM32_SPI1
+  /* Configure the SPI-based touch screen CS GPIO */
+  spivdbg("Configure GPIO for SPI1/CS\n");
+  stm32_configgpio(GPIO_TS_CS);
+#endif
+}
+
+/****************************************************************************
+ * Name:  stm32_spi1/2/3select and stm32_spi1/2/3status
+ *
+ * Description:
+ *   The external functions, stm32_spi1/2/3select and stm32_spi1/2/3status must be
+ *   provided by board-specific logic.  They are implementations of the select
+ *   and status methods of the SPI interface defined by struct spi_ops_s (see
+ *   include/nuttx/spi.h). All other methods (including up_spiinitialize())
+ *   are provided by common STM32 logic.  To use this common SPI logic on your
+ *   board:
+ *
+ *   1. Provide logic in stm32_boardinitialize() to configure SPI chip select
+ *      pins.
+ *   2. Provide stm32_spi1/2/3select() and stm32_spi1/2/3status() functions in your
+ *      board-specific logic.  These functions will perform chip selection and
+ *      status operations using GPIOs in the way your board is configured.
+ *   3. Add a calls to up_spiinitialize() in your low level application
+ *      initialization logic
+ *   4. The handle returned by up_spiinitialize() may then be used to bind the
+ *      SPI driver to higher level logic (e.g., calling
+ *      mmcsd_spislotinitialize(), for example, will bind the SPI driver to
+ *      the SPI MMC/SD driver).
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_STM32_SPI1
+void stm32_spi1select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+  spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
+
+  if (devid == SPIDEV_TOUCHSCREEN)
+  {
+    /* Set the GPIO low to select and high to de-select */
+
+    stm32_gpiowrite(GPIO_TS_CS, !selected);
+  }
+}
+
+uint8_t stm32_spi1status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+  return SPI_STATUS_PRESENT;
+}
+#endif
+
+#ifdef CONFIG_STM32_SPI2
+void stm32_spi2select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+  spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
+}
+
+uint8_t stm32_spi2status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+  return SPI_STATUS_PRESENT;
+}
+#endif
+
+#ifdef CONFIG_STM32_SPI3
+void stm32_spi3select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+  spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
+}
+
+uint8_t stm32_spi3status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+  return SPI_STATUS_PRESENT;
+}
+#endif
+
+#endif /* CONFIG_STM32_SPI1 || CONFIG_STM32_SPI2 */
diff --git a/nuttx/configs/hymini-stm32v/src/up_ts.c b/nuttx/configs/hymini-stm32v/src/up_ts.c
new file mode 100644
index 000000000..6c4decf7c
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_ts.c
@@ -0,0 +1,163 @@
+/************************************************************************************
+ * configs/hymini-stm32v/src/up_ts.c
+ * arch/arm/src/board/up_ts.c
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *           Laurent Latil <laurent@latil.nom.fr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+#include <nuttx/spi.h>
+#include <nuttx/arch.h>
+
+#include <errno.h>
+#include <debug.h>
+
+#include "stm32.h"
+#include "stm32_internal.h"
+#include "hymini_stm32v-internal.h"
+
+#include <nuttx/input/ads7843e.h>
+
+#if !defined(CONFIG_STM32_SPI1)
+# error CONFIG_STM32_SPI1 must be defined to use the ADS7843 on this board
+#endif
+
+static int hymini_ts_irq_attach(FAR struct ads7843e_config_s *state, xcpt_t isr);
+static void hymini_ts_irq_enable(FAR struct ads7843e_config_s *state,
+    bool enable);
+static void hymini_ts_irq_clear(FAR struct ads7843e_config_s *state);
+static bool hymini_ts_busy(FAR struct ads7843e_config_s *state);
+static bool hymini_ts_pendown(FAR struct ads7843e_config_s *state);
+
+/************************************************************************************
+ * Private Data
+ ************************************************************************************/
+
+static FAR struct ads7843e_config_s ts_cfg =
+{
+  .frequency = CONFIG_ADS7843E_FREQUENCY,
+
+  .attach = hymini_ts_irq_attach,
+  .enable=hymini_ts_irq_enable,
+  .clear=hymini_ts_irq_clear,
+  .busy = hymini_ts_busy,
+  .pendown=hymini_ts_pendown
+};
+
+static xcpt_t tc_isr;
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/* Attach the ADS7843E interrupt handler to the GPIO interrupt */
+static int hymini_ts_irq_attach(FAR struct ads7843e_config_s *state, xcpt_t isr)
+{
+  ivdbg("hymini_ts_irq_attach\n");
+
+  tc_isr = isr;
+  stm32_gpiosetevent(GPIO_TS_IRQ, true, true, true, isr);
+  return OK;
+}
+
+/* Enable or disable the GPIO interrupt */
+static void hymini_ts_irq_enable(FAR struct ads7843e_config_s *state,
+    bool enable)
+{
+  illvdbg("%d\n", enable);
+
+  stm32_gpiosetevent(GPIO_TS_IRQ, true, true, true, enable? tc_isr:NULL);
+}
+
+/* Acknowledge/clear any pending GPIO interrupt */
+static void hymini_ts_irq_clear(FAR struct ads7843e_config_s *state)
+{
+  // FIXME  Nothing to do ?
+}
+
+/* As the busy line is not connected, we just wait a little bit here */
+static bool hymini_ts_busy(FAR struct ads7843e_config_s *state)
+{
+  up_mdelay(50);
+  return false;
+}
+
+/* Return the state of the pen down GPIO input */
+static bool hymini_ts_pendown(FAR struct ads7843e_config_s *state)
+{
+  bool pin_value = stm32_gpioread(GPIO_TS_IRQ);
+  return !pin_value;
+}
+
+/****************************************************************************
+ * Name: arch_tcinitialize()
+ *
+ * Description:
+ *   Perform architecture-specific initialization of the touchscreen.
+ *   This function must be called directly from application.
+ *
+ ****************************************************************************/
+
+int arch_tcinitialize(int minor)
+{
+  FAR struct spi_dev_s *dev;
+
+  idbg("arch_tcinitialize: minor %d\n", minor);
+
+  dev = up_spiinitialize(1);
+  if (!dev)
+    {
+      idbg("arch_tcinitialize: Failed to initialize SPI bus\n");
+      return -ENODEV;
+    }
+
+  /* Configure the PIO interrupt */
+
+  stm32_configgpio(GPIO_TS_IRQ);
+
+  return ads7843e_register(dev, &ts_cfg, minor);
+}
+
+/****************************************************************************
+ * Name: arch_tcuninitialize()
+ *
+ * Description:
+ *   Perform architecture-specific un-initialization of the touchscreen
+ *   hardware.  This function must be called directly from application.
+ *
+ ****************************************************************************/
+
+void arch_tcuninitialize(void)
+{
+  /* FIXME What can/should we do here ? */
+}
diff --git a/nuttx/configs/hymini-stm32v/src/up_usbdev.c b/nuttx/configs/hymini-stm32v/src/up_usbdev.c
new file mode 100644
index 000000000..061ed9234
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_usbdev.c
@@ -0,0 +1,117 @@
+/************************************************************************************
+ * configs/hymini-stm32v/src/up_usbdev.c
+ * arch/arm/src/board/up_boot.c
+ *
+ *   Copyright (C) 2009-2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <sys/types.h>
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <nuttx/usb/usbdev.h>
+#include <nuttx/usb/usbdev_trace.h>
+
+#include "up_arch.h"
+#include "stm32_internal.h"
+#include "hymini_stm32v-internal.h"
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: stm32_usbinitialize
+ *
+ * Description:
+ *   Called to setup USB-related GPIO pins for the Hy-Mini STM32v board.
+ *
+ ************************************************************************************/
+
+void stm32_usbinitialize(void)
+{
+  ulldbg("called\n");
+
+  /* USB Soft Connect Pullup */
+  stm32_configgpio(GPIO_USB_PULLUP);
+}
+
+/************************************************************************************
+ * Name:  stm32_usbpullup
+ *
+ * Description:
+ *   If USB is supported and the board supports a pullup via GPIO (for USB software
+ *   connect and disconnect), then the board software must provide stm32_pullup.
+ *   See include/nuttx/usb/usbdev.h for additional description of this method.
+ *   Alternatively, if no pull-up GPIO the following EXTERN can be redefined to be
+ *   NULL.
+ *
+ ************************************************************************************/
+
+int stm32_usbpullup(FAR struct usbdev_s *dev, bool enable)
+{
+  usbtrace(TRACE_DEVPULLUP, (uint16_t)enable);
+  stm32_gpiowrite(GPIO_USB_PULLUP, !enable);
+  return OK;
+}
+
+/************************************************************************************
+ * Name:  stm32_usbsuspend
+ *
+ * Description:
+ *   Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
+ *   used.  This function is called whenever the USB enters or leaves suspend mode.
+ *   This is an opportunity for the board logic to shutdown clocks, power, etc.
+ *   while the USB is suspended.
+ *
+ ************************************************************************************/
+
+void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
+{
+  ulldbg("resume: %d\n", resume);
+}
+
diff --git a/nuttx/configs/hymini-stm32v/src/up_usbstrg.c b/nuttx/configs/hymini-stm32v/src/up_usbstrg.c
new file mode 100644
index 000000000..8a309c270
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/src/up_usbstrg.c
@@ -0,0 +1,164 @@
+/****************************************************************************
+ * configs/hymini-stm32v/src/up_usbstrg.c
+ *
+ *   Copyright (C) 2009, 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Configure and register the STM32 MMC/SD SDIO block driver.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdio.h>
+#include <debug.h>
+#include <errno.h>
+
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+
+#include "stm32_internal.h"
+
+/* There is nothing to do here if SDIO support is not selected. */
+
+#ifdef CONFIG_STM32_SDIO
+
+/****************************************************************************
+ * Pre-Processor Definitions
+ ****************************************************************************/
+
+/* Configuration ************************************************************/
+
+#ifndef CONFIG_EXAMPLES_USBSTRG_DEVMINOR1
+#  define CONFIG_EXAMPLES_USBSTRG_DEVMINOR1 0
+#endif
+
+/* SLOT number(s) could depend on the board configuration */
+
+#ifdef CONFIG_ARCH_BOARD_HYMINI_STM32V
+#  undef STM32_MMCSDSLOTNO
+#  define STM32_MMCSDSLOTNO 0
+#else
+   /* Add configuration for new STM32 boards here */
+#  error "Unrecognized STM32 board"
+#endif
+
+/* Debug ********************************************************************/
+
+#ifdef CONFIG_CPP_HAVE_VARARGS
+#  ifdef CONFIG_DEBUG
+#    define message(...) lib_lowprintf(__VA_ARGS__)
+#    define msgflush()
+#  else
+#    define message(...) printf(__VA_ARGS__)
+#    define msgflush() fflush(stdout)
+#  endif
+#else
+#  ifdef CONFIG_DEBUG
+#    define message lib_lowprintf
+#    define msgflush()
+#  else
+#    define message printf
+#    define msgflush() fflush(stdout)
+#  endif
+#endif
+
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: usbstrg_archinitialize
+ *
+ * Description:
+ *   Perform architecture specific initialization
+ *
+ ****************************************************************************/
+
+int usbstrg_archinitialize(void)
+{
+  /* If examples/usbstrg is built as an NSH command, then SD slot should
+   * already have been initialized in nsh_archinitialize() (see up_nsh.c).  In
+   * this case, there is nothing further to be done here.
+   */
+
+#ifndef CONFIG_EXAMPLES_USBSTRG_BUILTIN
+  FAR struct sdio_dev_s *sdio;
+  int ret;
+
+  /* First, get an instance of the SDIO interface */
+
+  message("usbstrg_archinitialize: "
+          "Initializing SDIO slot %d\n",
+          STM32_MMCSDSLOTNO);
+
+  sdio = sdio_initialize(STM32_MMCSDSLOTNO);
+  if (!sdio)
+    {
+      message("usbstrg_archinitialize: Failed to initialize SDIO slot %d\n",
+              STM32_MMCSDSLOTNO);
+      return -ENODEV;
+    }
+
+  /* Now bind the SDIO interface to the MMC/SD driver */
+
+  message("usbstrg_archinitialize: "
+          "Bind SDIO to the MMC/SD driver, minor=%d\n",
+          CONFIG_EXAMPLES_USBSTRG_DEVMINOR1);
+
+  ret = mmcsd_slotinitialize(CONFIG_EXAMPLES_USBSTRG_DEVMINOR1, sdio);
+  if (ret != OK)
+    {
+      message("usbstrg_archinitialize: "
+              "Failed to bind SDIO to the MMC/SD driver: %d\n",
+              ret);
+      return ret;
+    }
+  message("usbstrg_archinitialize: "
+          "Successfully bound SDIO to the MMC/SD driver\n");
+  
+  /* Then let's guess and say that there is a card in the slot.  I need to check to
+   * see if the Hy-Mini STM32v board supports a GPIO to detect if there is a card in
+   * the slot.
+   */
+
+   sdio_mediachange(sdio, true);
+
+#endif /* CONFIG_EXAMPLES_USBSTRG_BUILTIN */
+
+   return OK;
+}
+
+#endif /* CONFIG_STM32_SDIO */
diff --git a/nuttx/configs/hymini-stm32v/usbserial/Make.defs b/nuttx/configs/hymini-stm32v/usbserial/Make.defs
new file mode 100644
index 000000000..33863f9f1
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbserial/Make.defs
@@ -0,0 +1,174 @@
+############################################################################
+# configs/hymini-stm32v/usbserial/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_DFU),y)
+  LDSCRIPT = ld.script.dfu
+else
+  LDSCRIPT = ld.script
+endif
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbserial/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbserial/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/hymini-stm32v/usbserial/appconfig b/nuttx/configs/hymini-stm32v/usbserial/appconfig
new file mode 100644
index 000000000..14802f340
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbserial/appconfig
@@ -0,0 +1,39 @@
+############################################################################
+# configs/hymini-stm32v/usbserial/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/usbserial
+
diff --git a/nuttx/configs/hymini-stm32v/usbserial/defconfig b/nuttx/configs/hymini-stm32v/usbserial/defconfig
new file mode 100755
index 000000000..0e062ef6f
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbserial/defconfig
@@ -0,0 +1,953 @@
+############################################################################
+# configs/hymini-stm32v/usbserial/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+#   CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM3=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F103VCT6=y
+CONFIG_ARCH_BOARD=hymini-stm32v
+CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+
+CONFIG_BOARD_LOOPSPERMSEC=5483
+CONFIG_DRAM_SIZE=0x0000C000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=n
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=n
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+CONFIG_STM32_DFU=n
+
+#
+#  Individual subsystems can be enabled:
+#
+# Individual subsystems can be enabled:
+# AHB: 
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=n
+CONFIG_STM32_CRC=n
+CONFIG_STM32_FSMC=y
+CONFIG_STM32_SDIO=n
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI4=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=n
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_USB=y
+CONFIG_STM32_CAN=n
+CONFIG_STM32_BKP=n
+CONFIG_STM32_PWR=n
+CONFIG_STM32_DAC=n
+# APB2:
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_SPI1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=y
+CONFIG_STM32_ADC3=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F103V specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART2_SERIAL_CONSOLE=n
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=256
+CONFIG_USART2_TXBUFSIZE=256
+CONFIG_USART3_TXBUFSIZE=256
+CONFIG_USART4_TXBUFSIZE=256
+CONFIG_USART5_TXBUFSIZE=256
+
+CONFIG_USART1_RXBUFSIZE=256
+CONFIG_USART2_RXBUFSIZE=256
+CONFIG_USART3_RXBUFSIZE=256
+CONFIG_USART4_RXBUFSIZE=256
+CONFIG_USART5_RXBUFSIZE=256
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F103V specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=n
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=n
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=y
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_USB=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_MM_REGIONS=1
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2009
+CONFIG_START_MONTH=10
+CONFIG_START_DAY=23
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=n
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_NXFLAT=n
+CONFIG_SCHED_WORKQUEUE=n
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=n
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_DISABLE_ENVIRON=n
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=n
+CONFIG_FAT_LCNAMES=n
+CONFIG_FAT_LFN=n
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=1
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=n
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=0
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=420
+CONFIG_NET_TCP=n
+CONFIG_NET_TCP_CONNS=40
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=n
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=n
+CONFIG_NET_ICMP_PING=n
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=y
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration (Prolific PL2303 Emulation)
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=y
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB serial device class driver (Standard CDC ACM class)
+#
+# CONFIG_CDCSER
+#   Enable compilation of the USB serial driver
+# CONFIG_CDCSER_EP0MAXPACKET
+#   Endpoint 0 max packet size. Default 64
+# CONFIG_CDCSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation.  Default 2.
+# CONFIG_CDCSER_EPINTIN_FSSIZE
+#   Max package size for the interrupt IN endpoint if full speed mode.
+#   Default 64.
+# CONFIG_CDCSER_EPINTIN_HSSIZE
+#   Max package size for the interrupt IN endpoint if high speed mode.
+#   Default 64
+# CONFIG_CDCSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_CDCSER_EPBULKOUT_FSSIZE
+#   Max package size for the bulk OUT endpoint if full speed mode.
+#   Default 64.
+# CONFIG_CDCSER_EPBULKOUT_HSSIZE
+#   Max package size for the bulk OUT  endpoint if high speed mode.
+#   Default 512.
+# CONFIG_CDCSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# CONFIG_CDCSER_EPBULKIN_FSSIZE
+#   Max package size for the bulk IN endpoint if full speed mode.
+#   Default 64.
+# CONFIG_CDCSER_EPBULKIN_HSSIZE
+#   Max package size for the bulk IN  endpoint if high speed mode.
+#   Default 512.
+# CONFIG_CDCSER_NWRREQS and CONFIG_CDCSER_NRDREQS
+#   The number of write/read requests that can be in flight.
+#   Default 256.
+# CONFIG_CDCSER_VENDORID and CONFIG_CDCSER_VENDORSTR
+#   The vendor ID code/string.  Default 0x0525 and "NuttX"
+#   0x0525 is the Netchip vendor and should not be used in any
+#   products.  This default VID was selected for compatibility with
+#   the Linux CDC ACM default VID.
+# CONFIG_CDCSER_PRODUCTID and CONFIG_CDCSER_PRODUCTSTR
+#   The product ID code/string. Default 0xara7 and "CDC/ACM Serial"
+#   0xa4a7 was selected for compatibility with the Linux CDC ACM
+#   default PID.
+# CONFIG_CDCSER_RXBUFSIZE and CONFIG_CDCSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers. Default 256.
+#
+CONFIG_CDCSER=n
+#CONFIG_CDCSER_EP0MAXPACKET
+#CONFIG_CDCSER_EPINTIN
+#CONFIG_CDCSER_EPINTIN_FSSIZE
+#CONFIG_CDCSER_EPINTIN_HSSIZE
+#CONFIG_CDCSER_EPBULKOUT
+#CONFIG_CDCSER_EPBULKOUT_FSSIZE
+#CONFIG_CDCSER_EPBULKOUT_HSSIZE
+#CONFIG_CDCSER_EPBULKIN
+#CONFIG_CDCSER_EPBULKIN_FSSIZE
+#CONFIG_CDCSER_EPBULKIN_HSSIZE
+#CONFIG_CDCSER_NWRREQS
+#CONFIG_CDCSER_NRDREQS
+#CONFIG_CDCSER_VENDORID
+#CONFIG_CDCSER_VENDORSTR
+#CONFIG_CDCSER_PRODUCTID
+#CONFIG_CDCSER_PRODUCTSTR
+#CONFIG_CDCSER_RXBUFSIZE
+#CONFIG_CDCSER_TXBUFSIZE
+
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=n
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Settings for examples/uip
+#
+CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_UIP_DHCPC=n
+
+#
+# Settings for examples/nettest
+CONFIG_EXAMPLE_NETTEST_SERVER=n
+CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
+CONFIG_EXAMPLE_NETTEST_NOMAC=n
+CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=n
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=n
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Settings for examples/usbterm
+#
+# CONFIG_EXAMPLES_UBSTERM_BUILTIN - Build the usbterm example as an NSH
+#   built-in command.  NOTE:  This is not fully functional as of this
+#   writing.. It should work, but there is no mechanism in place yet
+#   to exit the USB terminal program and return to NSH.
+# CONFIG_EXAMPLES_USBTERM_BUFLEN - The size of the input and output
+#   buffers used for receiving data. Default 256 bytes.
+#
+# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB, or
+# CONFIG_USBDEV_TRACE), then the example code will also manage the USB trace
+# output.  The amount of trace output can be controlled using:
+#
+# CONFIG_EXAMPLES_USBTERM_TRACEINIT - Show initialization events
+# CONFIG_EXAMPLES_USBTERM_TRACECLASS - Show class driver events
+# CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS - Show data transfer events
+# CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER - Show controller events
+# CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS - Show interrupt-related events
+#
+CONFIG_EXAMPLES_UBSTERM_BUILTIN=n
+CONFIG_EXAMPLES_USBTERM_BUFLEN=256
+CONFIG_EXAMPLES_USBTERM_TRACEINIT=n
+CONFIG_EXAMPLES_USBTERM_TRACECLASS=n
+CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS=n
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the Hy-Mini STM32v which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/hymini-stm32v/usbserial/ld.script b/nuttx/configs/hymini-stm32v/usbserial/ld.script
new file mode 100755
index 000000000..8a8361614
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbserial/ld.script
@@ -0,0 +1,113 @@
+/****************************************************************************
+ * configs/hymini-stm32v/usbserial/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *           Laurent Latil <laurent@latil.nom.fr>
+ 
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103VCT6 has 256Kb of FLASH beginning at address 0x0800:0000 and
+ * 48Kb of SRAM beginning at address 0x2000:0000.  When booting from FLASH,
+ * FLASH memory is aliased to address 0x0000:0000 where the code expects to
+ * begin execution by jumping to the entry point in the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 256K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 48K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/usbserial/ld.script.dfu b/nuttx/configs/hymini-stm32v/usbserial/ld.script.dfu
new file mode 100755
index 000000000..5734ed267
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbserial/ld.script.dfu
@@ -0,0 +1,111 @@
+/****************************************************************************
+ * configs/hymini-stm32v/usbserial/ld.script.dfu
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  Here we assume that the
+ * Hy-Mini STM32v's DFU bootloader is being used.  In that case, the corrct
+ * load .text load address is 0x08003000 (leaving 464Kb).
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/usbserial/setenv.sh b/nuttx/configs/hymini-stm32v/usbserial/setenv.sh
new file mode 100755
index 000000000..6b324148d
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbserial/setenv.sh
@@ -0,0 +1,47 @@
+#!/bin/bash
+# configs/hymini-stm32v/ostest/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$(basename $0)" = "setenv.sh" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
+
+WD=`pwd`
+export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
+export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
+export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/hymini-stm32v/usbstorage/Make.defs b/nuttx/configs/hymini-stm32v/usbstorage/Make.defs
new file mode 100755
index 000000000..5583f97c6
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbstorage/Make.defs
@@ -0,0 +1,174 @@
+############################################################################
+# configs/hymini-stm32v/usbstorage/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_DFU),y)
+  LDSCRIPT = ld.script.dfu
+else
+  LDSCRIPT = ld.script
+endif
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbstorage/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbstorage/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/hymini-stm32v/usbstorage/appconfig b/nuttx/configs/hymini-stm32v/usbstorage/appconfig
new file mode 100644
index 000000000..3e171d83a
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbstorage/appconfig
@@ -0,0 +1,39 @@
+############################################################################
+# configs/hymini-stm32v/usbstorage/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/usbstorage
+
diff --git a/nuttx/configs/hymini-stm32v/usbstorage/defconfig b/nuttx/configs/hymini-stm32v/usbstorage/defconfig
new file mode 100755
index 000000000..43b2c1d8f
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbstorage/defconfig
@@ -0,0 +1,928 @@
+############################################################################
+# configs/hymini-stm32v/usbstorage/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The ST32F103Z supports interrupt prioritization
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+#   CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM3=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F103VCT6=y
+CONFIG_ARCH_BOARD=hymini-stm32v
+CONFIG_ARCH_BOARD_HYMINI_STM32V=y
+
+CONFIG_BOARD_LOOPSPERMSEC=5483
+CONFIG_DRAM_SIZE=0x0000C000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=n
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=y
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+CONFIG_STM32_DFU=n
+
+#
+# Individual subsystems can be enabled:
+# AHB: 
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=y
+CONFIG_STM32_CRC=n
+CONFIG_STM32_FSMC=y
+CONFIG_STM32_SDIO=y
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI4=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=n
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_USB=y
+CONFIG_STM32_CAN=n
+CONFIG_STM32_BKP=n
+CONFIG_STM32_PWR=n
+CONFIG_STM32_DAC=n
+# APB2:
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_SPI1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=y
+CONFIG_STM32_ADC3=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F103V specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART2_SERIAL_CONSOLE=n
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=256
+CONFIG_USART2_TXBUFSIZE=256
+CONFIG_USART3_TXBUFSIZE=256
+CONFIG_USART4_TXBUFSIZE=256
+CONFIG_USART5_TXBUFSIZE=256
+
+CONFIG_USART1_RXBUFSIZE=256
+CONFIG_USART2_RXBUFSIZE=256
+CONFIG_USART3_RXBUFSIZE=256
+CONFIG_USART4_RXBUFSIZE=256
+CONFIG_USART5_RXBUFSIZE=256
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F103V specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=n
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=n
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=y
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_FS=n
+CONFIG_DEBUG_USB=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_MM_REGIONS=1
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2009
+CONFIG_START_MONTH=11
+CONFIG_START_DAY=30
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=n
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SCHED_WORKQUEUE=y
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+
+#
+# Settings for NXFLAT
+#
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
+#  with.  CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
+#  CONFIG_DEBUG_BINFMT have to be defined or
+#  CONFIG_NXFLAT_DUMPBUFFER does nothing.
+# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
+#  is ordered by symbol name
+#
+CONFIG_NXFLAT=n
+CONFIG_NXFLAT_DUMPBUFFER=n
+CONFIG_SYMTAB_ORDEREDBYNAME=y
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=n
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_DISABLE_ENVIRON=n
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=n
+CONFIG_FAT_LCNAMES=n
+CONFIG_FAT_LFN=n
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=1
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=y
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=0
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=420
+CONFIG_NET_TCP=n
+CONFIG_NET_TCP_CONNS=40
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=n
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=n
+CONFIG_NET_ICMP_PING=n
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=y
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=y
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Settings for examples/uip
+#
+CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_UIP_DHCPC=n
+
+#
+# Settings for examples/nettest
+CONFIG_EXAMPLE_NETTEST_SERVER=n
+CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
+CONFIG_EXAMPLE_NETTEST_NOMAC=n
+CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_BUILTIN_APPS - Support external registered,
+#   "named" applications that can be executed from the NSH
+#   command line (see apps/README.txt for more information).
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_CONDEV - Select the serial device used to support
+#   the NSH console.  Default: stdin and stdout
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_BUILTIN_APPS=n
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+#CONFIG_NSH_CONDEV="/dev/ttyS1"
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=n
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Settings for examples/usbstorage
+#
+# CONFIG_EXAMPLES_USBSTRG_BUILTIN
+#   This example can be built as two NSH "built-in" commands if this option
+#   is selection: 'msconn' will connect the USB mass storage device; 'msdis'
+#   will disconnect the USB storage device.
+# CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    Defines the number of logical units (LUNs) exported by the USB storage
+#    driver.  Each LUN corresponds to one exported block driver (or partition
+#    of a block driver).  May be 1, 2, or 3.  Default is 1.
+# CONFIG_EXAMPLES_USBSTRG_DEVMINOR1
+#    The minor device number of the block driver for the first LUN. For
+#    example, N in /dev/mmcsdN.  Used for registering the block driver. Default
+#    is zero.
+# CONFIG_EXAMPLES_USBSTRG_DEVPATH1
+#    The full path to the registered block driver.  Default is "/dev/mmcsd0"
+#  CONFIG_EXAMPLES_USBSTRG_DEVMINOR2 and CONFIG_EXAMPLES_USBSTRG_DEVPATH2
+#    Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    is 2 or 3.  No defaults.
+#  CONFIG_EXAMPLES_USBSTRG_DEVMINOR3 and CONFIG_EXAMPLES_USBSTRG_DEVPATH3
+#    Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    is 3.  No defaults.
+#  CONFIG_EXAMPLES_USBSTRG_DEBUGMM
+#    Enables some debug tests to check for memory usage and memory leaks.
+#
+#  If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then
+#  the example code will also manage the USB trace output.  The amount of trace output
+#  can be controlled using:
+#
+#  CONFIG_EXAMPLES_USBSTRG_TRACEINIT
+#    Show initialization events
+#  CONFIG_EXAMPLES_USBSTRG_TRACECLASS
+#    Show class driver events
+#  CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS
+#    Show data transfer events
+#  CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER
+#    Show controller events
+#  CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS
+#    Show interrupt-related events.
+#
+CONFIG_EXAMPLES_USBSTRG_BUILTIN=n
+CONFIG_EXAMPLES_USBSTRG_NLUNS=1
+CONFIG_EXAMPLES_USBSTRG_DEVMINOR1=0
+CONFIG_EXAMPLES_USBSTRG_DEVPATH1="/dev/mmcsd0"
+CONFIG_EXAMPLES_USBSTRG_DEBUGMM=n
+CONFIG_EXAMPLES_USBSTRG_TRACEINIT=n
+CONFIG_EXAMPLES_USBSTRG_TRACECLASS=n
+CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS=n
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the Hy-Mini STM32v which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/hymini-stm32v/usbstorage/ld.script b/nuttx/configs/hymini-stm32v/usbstorage/ld.script
new file mode 100755
index 000000000..7e92fec83
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbstorage/ld.script
@@ -0,0 +1,112 @@
+/****************************************************************************
+ * configs/hymini-stm32v/usbstorage/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  When booting from FLASH,
+ * FLASH memory is aliased to address 0x0000:0000 where the code expects to
+ * begin execution by jumping to the entry point in the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 512K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/usbstorage/ld.script.dfu b/nuttx/configs/hymini-stm32v/usbstorage/ld.script.dfu
new file mode 100755
index 000000000..7bb2997c2
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbstorage/ld.script.dfu
@@ -0,0 +1,111 @@
+/****************************************************************************
+ * configs/hymini-stm32v/usbstorage/ld.script.dfu
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F103ZET6 has 512Kb of FLASH beginning at address 0x0800:0000 and
+ * 64Kb of SRAM beginning at address 0x2000:0000.  Here we assume that the
+ * Hy-Mini STM32v's DFU bootloader is being used.  In that case, the corrct
+ * load .text load address is 0x08003000 (leaving 464Kb).
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08003000, LENGTH = 464K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);
+
+	/* The STM32F103VCT6 has 48Kb of SRAM beginning at the following address */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} >sram
+	__exidx_end = ABSOLUTE(.);
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/hymini-stm32v/usbstorage/setenv.sh b/nuttx/configs/hymini-stm32v/usbstorage/setenv.sh
new file mode 100755
index 000000000..a0371cdce
--- /dev/null
+++ b/nuttx/configs/hymini-stm32v/usbstorage/setenv.sh
@@ -0,0 +1,47 @@
+#!/bin/bash
+# configs/hymini-stm32v/dfu/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$(basename $0)" = "setenv.sh" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
+
+WD=`pwd`
+export RIDE_BIN="/cygdrive/c/Program Files/Raisonance/Ride/arm-gcc/bin"
+export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
+export PATH="${BUILDROOT_BIN}:${RIDE_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"