Add support for the Olimex LPC1766-STK board

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@3079 42af7a65-404d-4744-a932-0658087f49c3

2 files changed, 103 insertions, 0 deletions

diff --git a/nuttx/configs/olimex-lpc1766stk/tools/olimex.cfg b/nuttx/configs/olimex-lpc1766stk/tools/olimex.cfg
new file mode 100755
index 000000000..6b98458e6
--- /dev/null
+++ b/nuttx/configs/olimex-lpc1766stk/tools/olimex.cfg
@@ -0,0 +1,61 @@
+#daemon configuration
+telnet_port 4444
+gdb_port 3333
+
+#interface
+interface ft2232
+ft2232_device_desc "Olimex OpenOCD JTAG A"
+ft2232_layout "olimex-jtag"
+ft2232_vid_pid 0x15BA 0x0003
+
+# NXP LPC1768 Cortex-M3 with 512kB Flash and 32kB+32kB Local On-Chip SRAM, clocked with 4MHz internal RC oscillator
+
+if { [info exists CHIPNAME] } {
+	set  _CHIPNAME $CHIPNAME
+} else {
+	set  _CHIPNAME lpc1768
+}
+
+if { [info exists ENDIAN] } {
+	set  _ENDIAN $ENDIAN
+} else {
+	set  _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+	set _CPUTAPID $CPUTAPID
+} else {
+	set _CPUTAPID 0x4ba00477
+}
+
+#delays on reset lines
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200
+
+# LPC2000 & LPC1700 -> SRST causes TRST
+reset_config trst_and_srst srst_pulls_trst
+
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
+
+# LPC1768 has 32kB of SRAM on its main system bus (so-called Local On-Chip SRAM)
+$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x8000 -work-area-backup 0
+
+# REVISIT is there any good reason to have this reset-init event handler??
+# Normally they should set up (board-specific) clocking then probe the flash...
+$_TARGETNAME configure -event reset-init {
+	# Force NVIC.VTOR to point to flash at 0 ...
+	# WHY?  This is it's reset value; we run right after reset!!
+	mwb 0xE000ED08 0x00
+}
+
+# LPC1768 has 512kB of user-available FLASH (bootloader is located in separate dedicated region).
+# flash bank lpc1700 <base> <size> 0 0 <target#> <variant> <cclk> [calc_checksum]
+
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME lpc2000 0x0 0x80000 0 0 $_TARGETNAME lpc1700 80000 calc_checksum
+
+# 4MHz / 6 = 666kHz, so use 500
+jtag_khz 100
diff --git a/nuttx/configs/olimex-lpc1766stk/tools/oocd.sh b/nuttx/configs/olimex-lpc1766stk/tools/oocd.sh
new file mode 100755
index 000000000..6f4bd6047
--- /dev/null
+++ b/nuttx/configs/olimex-lpc1766stk/tools/oocd.sh
@@ -0,0 +1,42 @@
+#!/bin/sh
+
+TOPDIR=$1
+USAGE="$0 <TOPDIR> [-d]"
+if [ -z "${TOPDIR}" ]; then
+	echo "Missing argument"
+	echo $USAGE
+	exit 1
+fi
+
+OPENOCD_PATH="/cygdrive/c/OpenOCD/openocd-0.4.0/src"
+OPENOCD_EXE=openocd.exe
+OPENOCD_CFG="${TOPDIR}/configs/olimex-lpc1766stk/tools/olimex.cfg"
+OPENOCD_ARGS="-f `cygpath -w ${OPENOCD_CFG}`"
+
+if [ "X$2" = "X-d" ]; then
+	OPENOCD_ARGS=$OPENOCD_ARGS" -d3"
+	set -x
+fi
+
+if [ ! -d ${OPENOCD_PATH} ]; then
+	echo "OpenOCD path does not exist: ${OPENOCD_PATH}"
+	exit 1
+fi
+if [ ! -x ${OPENOCD_PATH}/${OPENOCD_EXE} ]; then
+	echo "OpenOCD does not exist: ${OPENOCD_PATH}/${OPENOCD_EXE}"
+	exit 1
+fi
+if [ ! -f ${OPENOCD_CFG} ]; then
+	echo "OpenOCD config file does not exist: ${OPENOCD_CFG}"
+	exit 1
+fi
+
+echo "Starting OpenOCD"
+${OPENOCD_PATH}/${OPENOCD_EXE} ${OPENOCD_ARGS} &
+echo "OpenOCD daemon started"
+ps -ef | grep openocd
+echo "In GDB: target remote localhost:3333"
+
+
+
+