SAM4L: Mic fixes to get the SAM4L Xplained running. The ostest now passes.

3 files changed, 109 insertions, 49 deletions

diff --git a/nuttx/configs/sam4l-xplained/README.txt b/nuttx/configs/sam4l-xplained/README.txt
index 8d3784b3e..69a501fc4 100644
--- a/nuttx/configs/sam4l-xplained/README.txt
+++ b/nuttx/configs/sam4l-xplained/README.txt
@@ -15,7 +15,7 @@ Contents
   - NuttX OABI "buildroot" Toolchain
   - NXFLAT Toolchain
   - LEDs
-  - Virtual COM Port
+  - Serial Consoles
   - SAM4L Xplained Pro-specific Configuration Options
   - Configurations
 
@@ -243,8 +243,27 @@ LEDs
   apparently, running normmally.  If LED0 is flashing at approximately
   2Hz, then a fatal error has been detected and the system has halted.
 
-Virtual COM Port
-^^^^^^^^^^^^^^^^
+Serial Consoles
+^^^^^^^^^^^^^^^
+
+  USART0
+  ------
+
+  USART is available on connectors EXT1 and EXT4
+
+    EXT1  TXT4  GPIO  Function
+    ----  ---- ------ -----------
+     13    13   PB00  USART0_RXD
+     14    14   PB01  USART0_TXD
+     19    19         GND
+     20    20         VCC
+
+  If you have a TTL to RS-232 convertor then this is the most convenient
+  serial console to use.  It is the default in all of these configurations.
+  An option is to use the virtual COM port.
+
+  Virtual COM Port
+  ----------------
 
   The SAM4L Xplained Pro contains an Embedded Debugger (EDBG) that can be
   used to program and debug the ATSAM4LC4C using Serial Wire Debug (SWD).
@@ -278,8 +297,8 @@ SAM4L Xplained Pro-specific Configuration Options
        chip:
 
        CONFIG_ARCH_CHIP_SAM34
-       CONFIG_ARCH_CHIP_SAM3U
-       CONFIG_ARCH_CHIP_AT91SAM3U4
+       CONFIG_ARCH_CHIP_SAM4L
+       CONFIG_ARCH_CHIP_ATSAM4LC4C
 
     CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
        hence, the board that supports the particular chip or SoC.
@@ -298,7 +317,7 @@ SAM4L Xplained Pro-specific Configuration Options
 
     CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
 
-       CONFIG_DRAM_SIZE=0x0000c000 (48Kb)
+       CONFIG_DRAM_SIZE=0x00008000 (32Kb)
 
     CONFIG_DRAM_START - The start address of installed DRAM
 
@@ -396,7 +415,7 @@ SAM4L Xplained Pro-specific Configuration Options
     CONFIG_USART2_ISUART
     CONFIG_USART3_ISUART
 
-  AT91SAM3U specific device driver settings
+  ST91SAM4L specific device driver settings
 
     CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=0,1,2,3) or UART
            m (m=4,5) for the console and ttys0 (default is the USART1).
@@ -409,13 +428,6 @@ SAM4L Xplained Pro-specific Configuration Options
     CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
     CONFIG_U[S]ARTn_2STOP - Two stop bits
 
-  LCD Options.  Other than the standard LCD configuration options
-  (see configs/README.txt), the SAM4L Xplained Pro driver also supports:
-
-    CONFIG_LCD_PORTRAIT - Present the display in the standard 240x320
-       "Portrait" orientation.  Default:  The display is rotated to
-       support a 320x240 "Landscape" orientation.
-
 Configurations
 ^^^^^^^^^^^^^^
 
@@ -442,3 +454,25 @@ must be is one of the following:
   ostest:
     This configuration directory, performs a simple OS test using
     examples/ostest.
+
+    NOTES:
+
+    1. This configuration provides test output on USART0 which is available
+       on EXT1 or EXT4 (see the section "Serial Consoles" above).  The
+       virtual COM port could be used, instead, by reconfiguring to use
+       USART1 instead of USART0:
+
+       System Type -> AT91SAM3/4 Peripheral Support
+         CONFIG_SAM_USART0=y
+         CONFIG_SAM_USART1=n
+
+       Device Drivers -> Serial Driver Support -> Serial Console
+         CONFIG_USART0_SERIAL_CONSOLE=y
+
+       Device Drivers -> Serial Driver Support -> USART0 Configuration
+         CONFIG_USART0_2STOP=0
+         CONFIG_USART0_BAUD=115200
+         CONFIG_USART0_BITS=8
+         CONFIG_USART0_PARITY=0
+         CONFIG_USART0_RXBUFSIZE=256
+         CONFIG_USART0_TXBUFSIZE=256
diff --git a/nuttx/configs/sam4l-xplained/include/board.h b/nuttx/configs/sam4l-xplained/include/board.h
index fe0e2018d..691588091 100644
--- a/nuttx/configs/sam4l-xplained/include/board.h
+++ b/nuttx/configs/sam4l-xplained/include/board.h
@@ -84,15 +84,29 @@
 #define BOARD_RCFAST12M_FREQUENCY  12000000 /* Nominal frequency of RCFAST12M (Hz) */
 #define BOARD_RC1M_FREQUENCY       1000000  /* Nominal frequency of RC1M (Hz) */
 
+/* The SAM4L Xplained Pro has two on-board crystals:
+ *   XC100 12MHz     OSC0
+ *   XC101 32.768KHz OSC32
+ */
+
+/* OSC0 Configuration */
+
+#define BOARD_OSC0_FREQUENCY       12000000 /* 12MHz XTAL */
+
 /* OSC32 Configuration */
 
-#define BOARD_OSC32_FREQUENCY      32768
+#define BOARD_OSC32_FREQUENCY      32768    /* 32.768KHz XTAL */
 #define BOARD_OSC32_STARTUP_US     6100
 #define BOARD_OSC32_SELCURR        BSCIF_OSCCTRL32_SELCURR_300
+#define BOARD_OSC32_ISXTAL         1        /* OSC32 is a crystal */
 
 /* Digital Frequency Locked Loop configuration
  *  Fdfll = (Fclk * DFLLmul) / DFLLdiv
- *        = 32768 * (48000000/32760) / 1 = 48MHz
+ *        = 32768 * (48000000/32768) / 1 = 48MHz
+ *
+ * The actual frequency is 47.97MHz due to truncation of the multiplier.
+ * The 48MHz target value is treated as "not-to-exceed" value).  Use OSC0
+ * if you need more accuracy (12MHz with a multiplier of 4).
  *
  * DFLL0 source options (select one):
  *   BOARD_DFLL0_SOURCE_RCSYS      - System RC oscillator
@@ -105,9 +119,10 @@
  */
 
 #define BOARD_DFLL0_SOURCE_OSC32K  1
-#define BOARD_DFLL0_FREQUENCY      48000000
-#define BOARD_DFLL0_MUL            (BOARD_DFLL0_FREQUENCY / BOARD_OSC32_FREQUENCY)
+#define BOARD_DFLL0_TARGET         48000000
+#define BOARD_DFLL0_MUL            (BOARD_DFLL0_TARGET / BOARD_OSC32_FREQUENCY)
 #define BOARD_DFLL0_DIV            1
+#define BOARD_DFLL0_FREQUENCY      (BOARD_OSC32_FREQUENCY * BOARD_DFLL0_MUL / BOARD_DFLL0_DIV)
 
 /* Phase Locked Loop configuration
  *  Fdfll = (Fclk * PLLmul) / PLLdiv
@@ -134,22 +149,22 @@
  * NOTE: Nothing must be defined if the PLL0 is not used
  */
 
-/* System clock dividers: Fbus = Fsys >> BUSshift */
+/* System clock dividers: Fbus = Fmck >> BUSshift */
 
-#define BOARD_CPU_SHIFT            0 /* Fcpu = Fsys = 48MHz */
-#define BOARD_PBA_SHIFT            0 /* Fpba = Fsys = 48MHz */
-#define BOARD_PBB_SHIFT            0 /* Fpbb = Fsys = 48MHz */
-#define BOARD_PBC_SHIFT            0 /* Fpbc = Fsys = 48MHz */
-#define BOARD_PBD_SHIFT            0 /* Fpbd = Fsys = 48MHz */
+#define BOARD_CPU_SHIFT            0 /* Fcpu = Fmck = 48MHz */
+#define BOARD_PBA_SHIFT            0 /* Fpba = Fmck = 48MHz */
+#define BOARD_PBB_SHIFT            0 /* Fpbb = Fmck = 48MHz */
+#define BOARD_PBC_SHIFT            0 /* Fpbc = Fmck = 48MHz */
+#define BOARD_PBD_SHIFT            0 /* Fpbd = Fmck = 48MHz */
 
 /* Resulting frequencies */
 
-#define BOARD_MAIN_FREQUENCY       (12000000)
-#define BOARD_CPU_FREQUENCY        (BOARD_MAIN_FREQUENCY >> BOARD_CPU_SHIFT)
-#define BOARD_PBA_FREQUENCY        (BOARD_MAIN_FREQUENCY >> BOARD_PBA_SHIFT)
-#define BOARD_PBB_FREQUENCY        (BOARD_MAIN_FREQUENCY >> BOARD_PBB_SHIFT)
-#define BOARD_PBC_FREQUENCY        (BOARD_MAIN_FREQUENCY >> BOARD_PBC_SHIFT)
-#define BOARD_PBD_FREQUENCY        (BOARD_MAIN_FREQUENCY >> BOARD_PBD_SHIFT)
+#define BOARD_MCK_FREQUENCY        (BOARD_DFLL0_FREQUENCY)
+#define BOARD_CPU_FREQUENCY        (BOARD_MCK_FREQUENCY >> BOARD_CPU_SHIFT)
+#define BOARD_PBA_FREQUENCY        (BOARD_MCK_FREQUENCY >> BOARD_PBA_SHIFT)
+#define BOARD_PBB_FREQUENCY        (BOARD_MCK_FREQUENCY >> BOARD_PBB_SHIFT)
+#define BOARD_PBC_FREQUENCY        (BOARD_MCK_FREQUENCY >> BOARD_PBC_SHIFT)
+#define BOARD_PBD_FREQUENCY        (BOARD_MCK_FREQUENCY >> BOARD_PBD_SHIFT)
 
 /* USBC.
  *
@@ -238,10 +253,21 @@
 #define BUTTON_SW0_BIT     (1 << BUTTON_SW0)
 
 /* Alternate Function Disambiguation ************************************************/
-/* The SAM4L Xplained Pro contains an Embedded Debugger (EDBG) that can be
- * used to program and debug the ATSAM4LC4C using Serial Wire Debug (SWD).
- * The Embedded debugger also include a Virtual Com port interface over
- * USART1.  Virtual COM port connections:
+/* USART0 is also available on connectors EXT1 and EXT4:
+ *
+ * EXT1  TXT4  GPIO  Function
+ * ----  ---- ------ -----------
+ *  13    13   PB00  USART0_RXD
+ *  14    14   PB01  USART0_TXD
+ */
+
+#define GPIO_USART0_RXD    GPIO_USART0_RXD_4
+#define GPIO_USART0_TXD    GPIO_USART0_TXD_4
+
+/* The SAM4L Xplained Pro contains an Embedded Debugger (EDBG) that can be used to
+ * program and debug the ATSAM4LC4C using Serial Wire Debug (SWD).  The Embedded
+ * debugger also include a Virtual Com port interface over USART1.  Virtual COM
+ * port connections:
  *
  *   PC26 USART1 RXD
  *   PC27 USART1 TXD
diff --git a/nuttx/configs/sam4l-xplained/ostest/defconfig b/nuttx/configs/sam4l-xplained/ostest/defconfig
index 820b60ba6..d3219b2b6 100644
--- a/nuttx/configs/sam4l-xplained/ostest/defconfig
+++ b/nuttx/configs/sam4l-xplained/ostest/defconfig
@@ -124,7 +124,7 @@ CONFIG_ARCH_CHIP_SAM4L=y
 # CONFIG_ARCH_CHIP_SAM4S is not set
 
 #
-# AT91SAM3 Peripheral Support
+# AT91SAM3/4 Peripheral Support
 #
 CONFIG_SAM_PICOCACHE=y
 # CONFIG_SAM34_OCD is not set
@@ -141,8 +141,8 @@ CONFIG_SAM_PICOCACHE=y
 # CONFIG_SAM34_TWIM2 is not set
 # CONFIG_SAM34_TWIM3 is not set
 # CONFIG_SAM34_PICOUART is not set
-# CONFIG_SAM34_USART0 is not set
-CONFIG_SAM34_USART1=y
+CONFIG_SAM34_USART0=y
+# CONFIG_SAM34_USART1 is not set
 # CONFIG_SAM34_USART2 is not set
 # CONFIG_SAM34_USART3 is not set
 # CONFIG_SAM34_ADCIFE is not set
@@ -170,7 +170,7 @@ CONFIG_SAM34_USART1=y
 #
 # AT91SAM3/4 USART Configuration
 #
-CONFIG_USART1_ISUART=y
+CONFIG_USART0_ISUART=y
 
 #
 # AT91SAM3/4 GPIO Interrupt Configuration
@@ -331,22 +331,22 @@ CONFIG_DEV_NULL=y
 CONFIG_SERIAL=y
 CONFIG_DEV_LOWCONSOLE=y
 # CONFIG_16550_UART is not set
-CONFIG_ARCH_HAVE_USART1=y
+CONFIG_ARCH_HAVE_USART0=y
 CONFIG_MCU_SERIAL=y
-CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART0_SERIAL_CONSOLE=y
 # CONFIG_NO_SERIAL_CONSOLE is not set
 
 #
-# USART1 Configuration
+# USART0 Configuration
 #
-CONFIG_USART1_RXBUFSIZE=256
-CONFIG_USART1_TXBUFSIZE=256
-CONFIG_USART1_BAUD=115200
-CONFIG_USART1_BITS=8
-CONFIG_USART1_PARITY=0
-CONFIG_USART1_2STOP=0
-# CONFIG_USART1_IFLOWCONTROL is not set
-# CONFIG_USART1_OFLOWCONTROL is not set
+CONFIG_USART0_RXBUFSIZE=256
+CONFIG_USART0_TXBUFSIZE=256
+CONFIG_USART0_BAUD=115200
+CONFIG_USART0_BITS=8
+CONFIG_USART0_PARITY=0
+CONFIG_USART0_2STOP=0
+# CONFIG_USART0_IFLOWCONTROL is not set
+# CONFIG_USART0_OFLOWCONTROL is not set
 # CONFIG_SERIAL_IFLOWCONTROL is not set
 # CONFIG_SERIAL_OFLOWCONTROL is not set
 # CONFIG_USBDEV is not set