diff options
Diffstat (limited to 'nuttx/configs/ea3131')
-rwxr-xr-x | nuttx/configs/ea3131/src/Makefile | 2 | ||||
-rwxr-xr-x | nuttx/configs/ea3131/src/ea3131_internal.h | 10 | ||||
-rwxr-xr-x | nuttx/configs/ea3131/src/up_boot.c | 4 | ||||
-rwxr-xr-x | nuttx/configs/ea3131/src/up_sdram.c | 267 |
4 files changed, 282 insertions, 1 deletions
diff --git a/nuttx/configs/ea3131/src/Makefile b/nuttx/configs/ea3131/src/Makefile index a5eaae88a..e4db278f3 100755 --- a/nuttx/configs/ea3131/src/Makefile +++ b/nuttx/configs/ea3131/src/Makefile @@ -40,7 +40,7 @@ CFLAGS += -I$(TOPDIR)/sched ASRCS = AOBJS = $(ASRCS:.S=$(OBJEXT)) -CSRCS = up_boot.c up_buttons.c up_cgu.c up_leds.c up_spi.c +CSRCS = up_boot.c up_buttons.c up_cgu.c up_leds.c up_sdram.c up_spi.c ifeq ($(CONFIG_EXAMPLES_NSH_ARCHINIT),y) CSRCS += up_nsh.c endif diff --git a/nuttx/configs/ea3131/src/ea3131_internal.h b/nuttx/configs/ea3131/src/ea3131_internal.h index 5edf55019..05a4f36f9 100755 --- a/nuttx/configs/ea3131/src/ea3131_internal.h +++ b/nuttx/configs/ea3131/src/ea3131_internal.h @@ -74,6 +74,16 @@ * Public Functions
************************************************************************************/
+/****************************************************************************
+ * Name: lpc313x_sdraminitialize
+ *
+ * Description:
+ * Configure Micron MT48LC32M16A2 SDRAM on the EA3131 board
+ *
+ ****************************************************************************/
+
+extern void lpc313x_sdraminitialize(void);
+
/************************************************************************************
* Name: lpc313x_spiinitialize
*
diff --git a/nuttx/configs/ea3131/src/up_boot.c b/nuttx/configs/ea3131/src/up_boot.c index 9cb467870..f7e08f4cb 100755 --- a/nuttx/configs/ea3131/src/up_boot.c +++ b/nuttx/configs/ea3131/src/up_boot.c @@ -73,6 +73,10 @@ void lpc313x_boardinitialize(void)
{
+ /* Configure Micron MT48LC32M16A2 SDRAM on the EA3131 board */
+
+ lpc313x_sdraminitialize();
+
/* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function
* lpc313x_spiinitialize() has been brought into the link.
*/
diff --git a/nuttx/configs/ea3131/src/up_sdram.c b/nuttx/configs/ea3131/src/up_sdram.c new file mode 100755 index 000000000..cedfd1daf --- /dev/null +++ b/nuttx/configs/ea3131/src/up_sdram.c @@ -0,0 +1,267 @@ +/**************************************************************************** + * configs/ea3131/src/up_sdram.c + * arch/arm/src/board/up_sdram.c + * + * Copyright (C) 2009 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt <spudmonkey@racsa.co.cr> + * + * References: + * - NXP lpc313x.cdl.drivers.zip example driver code + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include <nuttx/config.h> + +#include <stdint.h> +#include <debug.h> + +#include <nuttx/arch.h> + +#include "chip.h" +#include "up_arch.h" + +#include "lpc313x_mpmc.h" +#include "lpc313x_cgudrvr.h" +#include "ea3131_internal.h" + +/**************************************************************************** + * Definitions + ****************************************************************************/ + +/* Enables debug output from this file (needs CONFIG_DEBUG with + * CONFIG_DEBUG_VERBOSE too) + */ + +#undef SDRAM_DEBUG /* Define to enable debug */ + +#ifdef SDRAM_DEBUG +# define sdramdbg lldbg +# define sdramvdbg llvdbg +#else +# define sdramdbg(x...) +# define sdramvdbg(x...) +#endif + +/*Delay constants in nanosecondss for MT48LC32M16LF SDRAM on board */ + +#define EA3131_SDRAM_TRP (20) +#define EA3131_SDRAM_TRFC (66) +#define EA3131_SDRAM_TRAS (44) +#define EA3131_SDRAM_TREX (75) +#define EA3131_SDRAM_TARP 4 +#define EA3131_SDRAM_TWR (75) +#define EA3131_SDRAM_TRC (66) +#define EA3131_SDRAM_TRRD (15) +#define EA3131_SDRAM_TMRD (20) +#define EA3131_SDRAM_TXSR (75) +#define EA3131_SDRAM_TDAL (50) +#define EA3131_SDRAM_REFRESH (100) +#define EA3131_SDRAM_OPERREFRESH (7812) + +/* Macro used to convert the above values (in nanoseconds) into units of + * the HCLK. + */ + +#define NS2HCLKS(ns,hclk2,mask) \ + ((uint32_t)(((uint64_t)ns *(uint64_t)hclk2) / 1000000000ull) & mask) + +/**************************************************************************** + * Private Data + ****************************************************************************/ + +/**************************************************************************** + * Private Functions + ****************************************************************************/ + +/**************************************************************************** + * Public Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: lpc313x_sdraminitialize + * + * Description: + * Configure SDRAM on the EA3131 board + * + * Micron Initialization Sequence from their data sheet for the Micron + * MT48LC32M16A2 32M x 16 SDRAM chip: + * + * "SDRAMs must be powered up and initialized in a predefined manner. + * Operational procedures other than those specified may result in + * undefined operation. Once power is applied to VDD and VDDQ + * (simultaneously) and the clock is stable (stable clock is defined as + * a signal cycling within timing constraints specified for the clock + * pin), the SDRAM requires a 100µs delay prior to issuing any command + * other than a COMMAND INHIBIT or NOP. + * + * "Starting at some point during this 100µs period and continuing at least + * through the end of this period, COMMAND INHIBIT or NOP commands should + * be applied. Once the 100µs delay has been satisfied with at least one + * COMMAND INHIBIT or NOP command having been applied, a PRECHARGE command + * should be applied. All banks must then be precharged, thereby placing + * the device in the all banks idle state. + * + * "Once in the idle state, two AUTO REFRESH cycles must be performed. After + * the AUTO REFRESH cycles are complete, the SDRAM is ready for mode + * register programming. + * + * "Because the mode register will power up in an unknown state, it should + * be loaded prior to applying any operational command." + * + * The JEDEC recommendation for initializing SDRAM is: + * + * APPLY POWER (Vdd/Vddq equally, and CLK is stable) + * Wait 200uS + * PRECHARGE all + * 8 AUTO REFRESH COMMANDS + * LOAD MODE REGISTER + * SDRAM is ready for operation + * + * The Micron SDRAM parts will work fine with the JEDEC sequence, but also + * allow for a quicker init sequence of: + * + * APPLY POWER (Vdd/Vddq equally, and CLK is stable) + * Wait at least 100uS (during which time start applying and + * continue applying NOP or COMMAND INHIBIT) + * PRECHARGE all + * 2 AUTO REFRESH COMMANDS (min requirement, more than 2 is also ok) + * LOAD MODE REGISTER + * SDRAM is ready for operation + * + ****************************************************************************/ + +void lpc313x_sdraminitialize(void) +{ + uint32_t tmp; + uint32_t regval; + + /* These run-time calculations can be reduced dramatically if hclk is + * replaced with an apriori value. + */ + +#ifdef CONFIG_LPC313X_SDRAMHCLK +# define HCLK CONFIG_LPC313X_SDRAMHCLK +#else + uint32_t hclk = lpc313x_clkfreq(CLKID_MPMCCFGCLK2, DOMAINID_SYS); +# define HCLK hclk +#endif + + /* Check RTL for divide by 2 possible. If so change then enable the following logic */ +#if 0 + uint32_t hclk2 = hclk; + + if (((getreg32(LPC313X_MPMC_CONFIG) & MPMC_CONFIG_CLK)) != 0) + { + hclk2 >>= 1; + } +# define HCLK2 hclk2 +#else +# define HCLK2 hclk +#endif + up_udelay(100); + + /* Set command delay startergy */ + + putreg32(MPMC_DYNREADCONFIG_CMDDEL, LPC313X_MPMC_DYNREADCONFIG); + + /* Configure device config register nSDCE0 for proper width SDRAM */ + + putreg32((MPMC_DYNCONFIG0_MDSDRAM|MPMC_DYNCONFIG_HP16_32MX16), LPC313X_MPMC_DYNCONFIG0); + putreg32((MPMC_DYNRASCAS0_RAS2CLK|MPMC_DYNRASCAS0_CAS2CLK), LPC313X_MPMC_DYNRASCAS0); + + /* Min 20ns program 1 so that at least 2 HCLKs are used */ + + putreg32(NS2HCLKS(EA3131_SDRAM_TRP, HCLK2, MPMC_DYNTRP_MASK), LPC313X_MPMC_DYNTRP); + putreg32(NS2HCLKS(EA3131_SDRAM_TRAS, HCLK2, MPMC_DYNTRAS_MASK), LPC313X_MPMC_DYNTRAS); + putreg32(NS2HCLKS(EA3131_SDRAM_TREX, HCLK2, MPMC_DYNTSREX_MASK), LPC313X_MPMC_DYNTSREX); + putreg32(EA3131_SDRAM_TARP, LPC313X_MPMC_DYNTAPR); + putreg32(NS2HCLKS(EA3131_SDRAM_TDAL, HCLK2, MPMC_DYNTDAL_MASK), LPC313X_MPMC_DYNTDAL); + putreg32(NS2HCLKS(EA3131_SDRAM_TWR, HCLK2, MPMC_DYNTWR_MASK), LPC313X_MPMC_DYNTWR); + putreg32(NS2HCLKS(EA3131_SDRAM_TRC, HCLK2, MPMC_DYNTRC_MASK), LPC313X_MPMC_DYNTRC); + putreg32(NS2HCLKS(EA3131_SDRAM_TRFC, HCLK2, MPMC_DYNTRFC_MASK), LPC313X_MPMC_DYNTRFC); + putreg32(NS2HCLKS(EA3131_SDRAM_TXSR, HCLK2, MPMC_DYNTXSR_MASK), LPC313X_MPMC_DYNTXSR); + putreg32(NS2HCLKS(EA3131_SDRAM_TRRD, HCLK2, MPMC_DYNTRRD_MASK), LPC313X_MPMC_DYNTRRD); + putreg32(NS2HCLKS(EA3131_SDRAM_TMRD, HCLK2, MPMC_DYNTMRD_MASK), LPC313X_MPMC_DYNTMRD); + up_udelay(100); + + /* Issue continuous NOP commands */ + + putreg32((MPMC_DYNCONTROL_CE|MPMC_DYNCONTROL_CS|MPMC_DYNCONTROL_INOP), LPC313X_MPMC_DYNCONTROL); + + /* Load ~200us delay value to timer1 */ + + up_udelay(200); + + /* Issue a "pre-charge all" command */ + + putreg32((MPMC_DYNCONTROL_CE|MPMC_DYNCONTROL_CS|MPMC_DYNCONTROL_IPALL), LPC313X_MPMC_DYNCONTROL); + + /* Minimum refresh pulse interval (tRFC) for MT48LC32M16A2=80nsec, 100nsec provides more than adequate interval. + */ + + putreg32(NS2HCLKS(EA3131_SDRAM_REFRESH, HCLK, MPMC_DYNREFRESH_TIMER_MASK), LPC313X_MPMC_DYNREFRESH); + + /* Load ~250us delay value to timer1 */ + + up_udelay(250); + + /* Recommended refresh interval for normal operation of the Micron MT48LC16LFFG = 7.8125usec (128KHz rate). ((HCLK / 128000) - 1) = refresh counter interval rate, (subtract one for safety margin). + */ + + putreg32(NS2HCLKS(EA3131_SDRAM_OPERREFRESH, HCLK, MPMC_DYNREFRESH_TIMER_MASK), LPC313X_MPMC_DYNREFRESH); + + /* Select mode register update mode */ + + putreg32((MPMC_DYNCONTROL_CE|MPMC_DYNCONTROL_CS|MPMC_DYNCONTROL_IMODE), LPC313X_MPMC_DYNCONTROL); + + /* Program the SDRAM internal mode registers on bank nSDCE0 and reconfigure the SDRAM chips. Bus speeds up to 90MHz requires use of a CAS latency = 2. To get correct value on address bus CAS cycle, requires a shift by 13 for 16bit mode + */ + + tmp = getreg32(LPC313X_EXTSDRAM0_VSECTION | (0x23 << 13)); + + putreg32((MPMC_DYNCONFIG0_MDSDRAM|MPMC_DYNCONFIG_HP16_32MX16), LPC313X_MPMC_DYNCONFIG0); + putreg32((MPMC_DYNRASCAS0_RAS2CLK|MPMC_DYNRASCAS0_CAS2CLK), LPC313X_MPMC_DYNRASCAS0); + + /* Select normal operating mode */ + + putreg32((MPMC_DYNCONTROL_CE|MPMC_DYNCONTROL_CS|MPMC_DYNCONTROL_INORMAL), LPC313X_MPMC_DYNCONTROL); + + /* Enable buffers */ + + regval = getreg32(LPC313X_MPMC_DYNCONFIG0); + regval |= MPMC_DYNCONFIG0_B; + putreg32(regval, LPC313X_MPMC_DYNCONFIG0); + + putreg32((MPMC_DYNCONTROL_INORMAL|MPMC_DYNCONTROL_CS), LPC313X_MPMC_DYNCONTROL); +} |