diff options
Diffstat (limited to 'nuttx/configs/olimex-lpc1766stk/README.txt')
| -rw-r--r-- | nuttx/configs/olimex-lpc1766stk/README.txt | 55 |
1 files changed, 24 insertions, 31 deletions
diff --git a/nuttx/configs/olimex-lpc1766stk/README.txt b/nuttx/configs/olimex-lpc1766stk/README.txt index 13c63d18b..990d1141a 100644 --- a/nuttx/configs/olimex-lpc1766stk/README.txt +++ b/nuttx/configs/olimex-lpc1766stk/README.txt @@ -935,44 +935,37 @@ Where <subdir> is one of the following: Configuration Notes: - 1. Uses the buildroot toolchaing (CONFIG_LPC17_BUILDROOT=y). But that is - easily reconfigured (see above) - 2. Support for FAT long file names is built-in but can easily be - removed if you are concerned about Microsoft patent issues (see the - section "FAT Long File Names" in the top-level COPYING file). - - CONFIG_FS_FAT=y - CONFIG_FAT_LCNAMES=y <-- Long file name support - CONFIG_FAT_LFN=y - CONFIG_FAT_MAXFNAME=32 - CONFIG_FS_NXFFS=n - CONFIG_FS_ROMFS=n + NOTES: + + 1. This configuration uses the mconf-based configuration tool. To + change this configuration using that tool, you should: - 3. Includes logic to support a button test (apps/examples/buttons). To - enable the button test, make the following changes in the .config - after configuring: + a. Build and install the kconfig-mconf tool. See nuttx/README.txt + and misc/tools/ + + b. Execute 'make menuconfig' in nuttx/ in order to start the + reconfiguration process. - -CONFIG_ARCH_BUTTONS=n - +CONFIG_ARCH_BUTTONS=y + 2. Uses the older, OABI, buildroot toolchain. But that is easily + reconfigured: - -CONFIG_GPIO_IRQ=n - -CONFIG_ARCH_IRQBUTTONS=n - +CONFIG_GPIO_IRQ=y - +CONFIG_ARCH_IRQBUTTONS=y + CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT=y : Buildroot toolchain + CONFIG_ARMV7M_OABI_TOOLCHAIN=y : Older, OABI toolchain - 4. This example supports the CAN loopback test (apps/examples/can) but this - must be manually enabled by selecting: + 3. This configuration supports a network. You may have to change + these settings for your network: - CONFIG_CAN=y : Enable the generic CAN infrastructure - CONFIG_LPC17_CAN1=y : Enable CAN1 - CONFIG_CAN_LOOPBACK=y : Enable CAN loopback mode + CONFIG_NSH_IPADDR=0x0a000002 : IP address: 10.0.0.2 + CONFIG_NSH_DRIPADDR=0x0a000001 : Gateway: 10.0.0.1 + CONFIG_NSH_NETMASK=0xffffff00 : Netmask: 255.255.255.0 - See also apps/examples/README.txt - - Special CAN-only debug options: + 4. This configuration supports the SPI-based MMC/SD card slot. + FAT file system support for FAT long file names is built-in but + can easily be removed if you are concerned about Microsoft patent + issues (see the section "FAT Long File Names" in the top-level + COPYING file). - CONFIG_DEBUG_CAN - CONFIG_CAN_REGDEBUG + CONFIG_FAT_LFN=y : Enables long file name support nx: An example using the NuttX graphics system (NX). This example uses |