diff options
Diffstat (limited to 'nuttx/configs/stm3220g-eval/telnetd/defconfig')
| -rw-r--r-- | nuttx/configs/stm3220g-eval/telnetd/defconfig | 57 |
1 files changed, 39 insertions, 18 deletions
diff --git a/nuttx/configs/stm3220g-eval/telnetd/defconfig b/nuttx/configs/stm3220g-eval/telnetd/defconfig index c4e439cc1..152c6ca1f 100644 --- a/nuttx/configs/stm3220g-eval/telnetd/defconfig +++ b/nuttx/configs/stm3220g-eval/telnetd/defconfig @@ -94,6 +94,8 @@ CONFIG_ARCH_DMA=n # CONFIG_STM32_CODESOURCERYW=y CONFIG_STM32_CODESOURCERYL=n +CONFIG_STM32_ATOLLIC_LITE=n +CONFIG_STM32_ATOLLIC_PRO=n CONFIG_STM32_DEVKITARM=n CONFIG_STM32_RAISONANCE=n CONFIG_STM32_BUILDROOT=n @@ -116,6 +118,29 @@ CONFIG_STM32_JTAG_NOJNTRST_ENABLE=n CONFIG_STM32_JTAG_SW_ENABLE=n # +# On-chip CCM SRAM configuration +# +# CONFIG_STM32_CCMEXCLUDE - Exclude CCM SRAM from the HEAP. You would need +# to do this if DMA is enabled to prevent non-DMA-able CCM memory from +# being a part of the stack. +# + +# +# On-board FSMC SRAM configuration +# +# CONFIG_STM32_FSMC - Required. See below +# CONFIG_MM_REGIONS - Required. Must be 2 or 3 (see above) +# +# CONFIG_STM32_FSMC_SRAM=y - Indicates that SRAM is available via the +# FSMC (as opposed to an LCD or FLASH). +# CONFIG_HEAP2_BASE - The base address of the SRAM in the FSMC address space +# CONFIG_HEAP2_END - The end (+1) of the SRAM in the FSMC address space +# +CONFIG_STM32_FSMC_SRAM=y +CONFIG_HEAP2_BASE=0x64000000 +CONFIG_HEAP2_END=(0x64000000+(2*1024*1024)) + +# # Individual subsystems can be enabled: # # Individual subsystems can be enabled: @@ -268,6 +293,8 @@ CONFIG_SSI_POLLWAIT=y # mode for testing. The STM32 CAN driver does support loopback mode. # CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined. # CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined. +# CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6 +# CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7 # CONFIG_CAN=n CONFIG_CAN_EXTID=n @@ -314,7 +341,7 @@ CONFIG_STM32_MII_MCO2=n CONFIG_STM32_RMII=n CONFIG_STM32_AUTONEG=y #CONFIG_STM32_ETHFD -#CONFIG_STM32_ETH100MB +#CONFIG_STM32_ETH100MBPS CONFIG_STM32_PHYSR=16 CONFIG_STM32_PHYSR_SPEED=0x0002 CONFIG_STM32_PHYSR_100MBPS=0x0000 @@ -362,7 +389,10 @@ CONFIG_HAVE_LIBM=n # CONFIG_DEBUG_VERBOSE - enables verbose debug output # CONFIG_DEBUG_SYMBOLS - build without optimization and with # debug symbols (needed for use with a debugger). -# CONFIG_HAVE_CXX - Enable support for C++S +# CONFIG_HAVE_CXX - Enable support for C++ +# CONFIG_HAVE_CXXINITIALIZE - The platform-specific logic includes support +# for initialization of static C++ instances for this architecture +# and for the selected toolchain (via up_cxxinitialize()). # CONFIG_MM_REGIONS - If the architecture includes multiple # regions of memory to allocate from, this specifies the # number of memory regions that the memory manager must @@ -451,12 +481,13 @@ CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n CONFIG_DEBUG_NET=n CONFIG_HAVE_CXX=y -CONFIG_MM_REGIONS=1 +CONFIG_HAVE_CXXINITIALIZE=y +CONFIG_MM_REGIONS=2 CONFIG_ARCH_LOWPUTC=y CONFIG_RR_INTERVAL=200 CONFIG_SCHED_INSTRUMENTATION=n CONFIG_TASK_NAME_SIZE=0 -CONFIG_START_YEAR=2011 +CONFIG_START_YEAR=2012 CONFIG_START_MONTH=12 CONFIG_START_DAY=6 CONFIG_GREGORIAN_TIME=n @@ -696,6 +727,9 @@ CONFIG_FS_WRITEBUFFER=n # Default: Medium # CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default: # 4-bit transfer mode. +# CONFIG_MMCSD_MULTIBLOCK_DISABLE - Use only the single block transfer method. +# This setting is used to work around buggy drivers that cannot handle +# multiple block transfers. # CONFIG_MMCSD_MMCSUPPORT # Enable support for MMC cards # CONFIG_MMCSD_HAVECARDDETECT @@ -705,20 +739,7 @@ CONFIG_SDIO_DMA=n #CONFIG_SDIO_PRI=128 #CONFIG_SDIO_DMAPRIO #CONFIG_SDIO_WIDTH_D1_ONLY -CONFIG_MMCSD_MMCSUPPORT=n -CONFIG_MMCSD_HAVECARDDETECT=n - -# -# SDIO-based MMC/SD driver -# -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# -CONFIG_SDIO_DMA=n +CONFIG_MMCSD_MULTIBLOCK_DISABLE=y CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n |