diff options
Diffstat (limited to 'nuttx')
-rw-r--r-- | nuttx/arch/mips/src/pic32mx/pic32mx-serial.c | 40 | ||||
-rw-r--r-- | nuttx/configs/pic32-starterkit/README.txt | 42 | ||||
-rw-r--r-- | nuttx/configs/pic32-starterkit/nsh2/Make.defs | 160 | ||||
-rw-r--r-- | nuttx/configs/pic32-starterkit/nsh2/appconfig | 115 | ||||
-rw-r--r-- | nuttx/configs/pic32-starterkit/nsh2/defconfig | 1475 | ||||
-rw-r--r-- | nuttx/configs/pic32-starterkit/nsh2/ld.script | 317 | ||||
-rwxr-xr-x | nuttx/configs/pic32-starterkit/nsh2/setenv.sh | 61 | ||||
-rwxr-xr-x | nuttx/configs/stm3240g-eval/README.txt | 4 |
8 files changed, 2205 insertions, 9 deletions
diff --git a/nuttx/arch/mips/src/pic32mx/pic32mx-serial.c b/nuttx/arch/mips/src/pic32mx/pic32mx-serial.c index 334c03d1c..f04e7f682 100644 --- a/nuttx/arch/mips/src/pic32mx/pic32mx-serial.c +++ b/nuttx/arch/mips/src/pic32mx/pic32mx-serial.c @@ -66,13 +66,6 @@ /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ -/* Some sanity checks *******************************************************/ -/* Is there at least one UART enabled and configured as a RS-232 device? */ - -#ifndef HAVE_UART_DEVICE -# warning "No UARTs enabled" -#endif - /* If we are not using the serial driver for the console, then we still must * provide some minimal implementation of up_putc. */ @@ -119,6 +112,14 @@ # endif #endif +/* Common initialization logic will not not know that the all of the UARTs + * have been disabled. So, as a result, we may still have to provide + * stub implementations of up_earlyserialinit(), up_serialinit(), and + * up_putc(). + */ + +#ifdef HAVE_UART_DEVICE + /* These values describe the set of enabled interrupts */ #define IE_RX (1 << 0) @@ -868,6 +869,31 @@ int up_putc(int ch) return ch; } +/**************************************************************************** + * Name: up_earlyserialinit, up_serialinit, and up_putc + * + * Description: + * stubs that may be needed. These stubs would be used if all UARTs are + * disabled. In that case, the logic in common/up_initialize() is not + * smart enough to know that there are not UARTs and will still expect + * these interfaces to be provided. + * + ****************************************************************************/ +#else /* HAVE_UART_DEVICE */ +void up_earlyserialinit(void) +{ +} + +void up_serialinit(void) +{ +} + +int up_putc(int ch) +{ + return ch; +} + +#endif /* HAVE_UART_DEVICE */ #else /* USE_SERIALDRIVER */ /**************************************************************************** diff --git a/nuttx/configs/pic32-starterkit/README.txt b/nuttx/configs/pic32-starterkit/README.txt index 3fe6c9e79..29dcafbd8 100644 --- a/nuttx/configs/pic32-starterkit/README.txt +++ b/nuttx/configs/pic32-starterkit/README.txt @@ -1073,3 +1073,45 @@ Where <subdir> is one of the following: And enable poll() support in the NuttX configuration file: CONFIG_DISABLE_POLL=n + + nsh2: + ===== + + This is an alternative NSH configuration. Without the Expansion I/O board, + there is no way to connect a serial console. This NSH alternative supports + only a Telnet console. The nsh2 differs from the nsh configuration in the + following ways: + + 1. Networking is enabled: + + CONFIG_NET=y : Enable networking support + CONFIG_PIC32MX_ETHERNET=y : Enable the PIC32 Ethernet driver + CONFIG_NSH_TELNET=y : Enable the Telnet NSH console (optional) + + See apps/nshlib/README.txt for other NSH networking-related configuration + settings. + + 2. UART1 is disabled + + CONFIG_PIC32MX_UART1=n : UART1 is disabled (as well as other UARTs) + CONFIG_UART1_SERIAL_CONSOLE=n : There is no serial console + + 3. The RAM log is enabled" + + CONFIG_SYSLOG=y : Enables the System Logging feature. + CONFIG_RAMLOG=y : Enable the RAM-based logging feature. + CONFIG_RAMLOG_CONSOLE=n : (there is no default console device) + CONFIG_RAMLOG_SYSLOG=y : This enables the RAM-based logger as the + system logger. + + Logging is currently set up to use 16Kb of memory: + + CONFIG_RAMLOG_CONSOLE_BUFSIZE=16384 + + There are a few other configuration differences as necessary to support + this different device configuration. Just the do the 'diff' if you are + curious. + + NOTES: + See the notes for the nsh configuration. Most also apply to the nsh2 + configuration. diff --git a/nuttx/configs/pic32-starterkit/nsh2/Make.defs b/nuttx/configs/pic32-starterkit/nsh2/Make.defs new file mode 100644 index 000000000..8c031f315 --- /dev/null +++ b/nuttx/configs/pic32-starterkit/nsh2/Make.defs @@ -0,0 +1,160 @@ +############################################################################ +# configs/pic32-starterkit/nsh2/Make.defs +# +# Copyright (C) 2012 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +include ${TOPDIR}/.config + +# Setup for the selected toolchain + +ifeq ($(CONFIG_PIC32MX_MICROCHIPW),y) + # Microchip toolchain under Windows + CROSSDEV = pic32- + WINTOOL = y + MAXOPTIMIZATION = -O2 + ARCHCPUFLAGS = -mprocessor=elf32pic32mx -mno-float -mlong32 -membedded-data + ARCHPICFLAGS = -fpic -membedded-pic + LDFLAGS += -nostartfiles -nodefaultlibs +endif +ifeq ($(CONFIG_PIC32MX_MICROCHIPW_LITE),y) + # Microchip toolchain under Windows + CROSSDEV = pic32- + WINTOOL = y +# MAXOPTIMIZATION = -O2 + ARCHCPUFLAGS = -mprocessor=elf32pic32mx -mno-float -mlong32 -membedded-data + ARCHPICFLAGS = -fpic -membedded-pic + LDFLAGS += -nostartfiles -nodefaultlibs +endif +ifeq ($(CONFIG_PIC32MX_MICROCHIPL),y) + # Microchip toolchain under Linux + CROSSDEV = pic32- + MAXOPTIMIZATION = -O2 + ARCHCPUFLAGS = -mprocessor=elf32pic32mx -mno-float -mlong32 -membedded-data + ARCHPICFLAGS = -fpic -membedded-pic + LDFLAGS += -nostartfiles -nodefaultlibs +endif +ifeq ($(CONFIG_PIC32MX_MICROCHIPL_LITE),y) + # Microchip toolchain under Linux + CROSSDEV = pic32- +# MAXOPTIMIZATION = -O2 + ARCHCPUFLAGS = -mprocessor=elf32pic32mx -mno-float -mlong32 -membedded-data + ARCHPICFLAGS = -fpic -membedded-pic + LDFLAGS += -nostartfiles -nodefaultlibs +endif + +ifeq ($(WINTOOL),y) + # Windows-native toolchains + DIRLINK = $(TOPDIR)/tools/winlink.sh + DIRUNLINK = $(TOPDIR)/tools/unlink.sh + MKDEP = $(TOPDIR)/tools/mknulldeps.sh + ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" + ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}" + ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/ld.script}" +else + # Linux/Cygwin-native toolchain + MKDEP = $(TOPDIR)/tools/mkdeps.sh + ARCHINCLUDES = -I. -isystem $(TOPDIR)/include + ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx + ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh2/ld.script +endif + +CC = $(CROSSDEV)gcc +CXX = $(CROSSDEV)g++ +CPP = $(CROSSDEV)gcc -E +LD = $(CROSSDEV)ld +AR = $(CROSSDEV)ar rcs +NM = $(CROSSDEV)nm +OBJCOPY = $(CROSSDEV)objcopy +OBJDUMP = $(CROSSDEV)objdump + +ifeq ("${CONFIG_DEBUG_SYMBOLS}","y") + ARCHOPTIMIZATION = -g +else + ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer +endif + +ARCHCFLAGS = -fno-builtin +ARCHCXXFLAGS = -fno-builtin -fno-exceptions +ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow +ARCHWARNINGSXX = -Wall -Wshadow +ARCHDEFINES = + +CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe +CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS) +CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe +CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS) +CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) +AFLAGS = $(CFLAGS) -D__ASSEMBLY__ + +NXFLATLDFLAGS1 = -r -d -warn-common +NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections +LDNXFLATFLAGS = -e main -s 2048 + +OBJEXT = .o +LIBEXT = .a +EXEEXT = + +define PREPROCESS + @echo "CPP: $1->$2" + @$(CPP) $(CPPFLAGS) $1 -o $2 +endef + +define COMPILE + @echo "CC: $1" + @$(CC) -c $(CFLAGS) $1 -o $2 +endef + +define COMPILEXX + @echo "CXX: $1" + @$(CXX) -c $(CXXFLAGS) $1 -o $2 +endef + +define ASSEMBLE + @echo "AS: $1" + @$(CC) -c $(AFLAGS) $1 -o $2 +endef + +define ARCHIVE + echo "AR: $2"; \ + $(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; } +endef + +define CLEAN + @rm -f *.o *.a +endef + +HOSTCC = gcc +HOSTINCLUDES = -I. +HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe +HOSTLDFLAGS = + diff --git a/nuttx/configs/pic32-starterkit/nsh2/appconfig b/nuttx/configs/pic32-starterkit/nsh2/appconfig new file mode 100644 index 000000000..83f7aa874 --- /dev/null +++ b/nuttx/configs/pic32-starterkit/nsh2/appconfig @@ -0,0 +1,115 @@ +############################################################################ +# configs/pic32-starterkit/nsh2/appconfig +# +# Copyright (C) 2012 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +############################################################################ +# Path to example in apps/examples containing the user_start entry point +############################################################################ + +CONFIGURED_APPS += examples/nsh + +############################################################################ +# The NSH application library +############################################################################ + +CONFIGURED_APPS += system/readline +CONFIGURED_APPS += nshlib + +############################################################################ +# USB device configurations +############################################################################ + +ifeq ($(CONFIG_PIC32MX_USBDEV),y) + +# USB Mass Storage Class device configurations + +ifeq ($(CONFIG_USBMSC),y) +# Uncomment to enable the examples/usbstorage built-in +# CONFIGURED_APPS += examples/usbstorage +endif + +# USB CDC/ACM serial device configurations + +ifeq ($(CONFIG_CDCACM),y) +# Uncomment to enable the examples/cdcacm built-in +# CONFIGURED_APPS += examples/cdcacm +# Uncomment the following to enable the examples/usbterm built-in +# CONFIGURED_APPS += examples/usbterm +endif + +# Prolifics PL2303 emulation configurations + +ifeq ($(CONFIG_PL2303),y) +# Uncomment the following to enable the examples/usbterm built-in +# CONFIGURED_APPS += examples/usbterm +endif +endif + +############################################################################ +# Networking configurations +############################################################################ + +# Networking libraries. +# Uncomment netutils/ftpc to include an FTP client library +# Uncomment netutils/ftpd to include an FTP server library + +ifeq ($(CONFIG_NET),y) +CONFIGURED_APPS += netutils/uiplib +CONFIGURED_APPS += netutils/resolv +CONFIGURED_APPS += netutils/webclient +CONFIGURED_APPS += netutils/tftpc +#CONFIGURED_APPS += netutils/ftpc +#CONFIGURED_APPS += netutils/ftpd +ifeq ($(CONFIG_NSH_TELNET),y) +CONFIGURED_APPS += netutils/telnetd +endif +endif + +# Uncomment examples/ftpc to include the FTP client example +# Uncomment examples/ftpd to include the FTP daemon example + +ifeq ($(CONFIG_NET),y) +#CONFIGURED_APPS += examples/ftpc +#CONFIGURED_APPS += examples/ftpd +endif + +############################################################################ +# Other pplications that can be configured as an NX built-in commands +############################################################################ + +ifeq ($(CONFIG_I2C),y) +CONFIGURED_APPS += system/i2c +endif + + diff --git a/nuttx/configs/pic32-starterkit/nsh2/defconfig b/nuttx/configs/pic32-starterkit/nsh2/defconfig new file mode 100644 index 000000000..bbd9cd75b --- /dev/null +++ b/nuttx/configs/pic32-starterkit/nsh2/defconfig @@ -0,0 +1,1475 @@ +############################################################################ +# configs/pic32-starterkit/nsh2/defconfig +# +# Copyright (C) 2012 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ +# +# architecture selection +# +# CONFIG_ARCH - identifies the arch subdirectory and, hence, the +# processor architecture. +# CONFIG_ARCH_family - for use in C code. This identifies the +# particular chip family that the architecture is implemented +# in. +# CONFIG_ARCH_architecture - for use in C code. This identifies the +# specific architecture within the chip family. +# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory +# CONFIG_ARCH_CHIP_name - For use in C code +# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, +# the board that supports the particular chip or SoC. +# CONFIG_ARCH_BOARD_name - for use in C code +# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) +# NOTE: The PIC32MX is always little endian. +# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure +# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until +# the delay actually is 100 seconds. +# CONFIG_DRAM_SIZE - Describes the installed DRAM. +# CONFIG_DRAM_START - The start address of DRAM (physical) +# CONFIG_DRAM_END - Last address+1 of installed RAM +# CONFIG_ARCH_NOINTC - define if the architecture does not +# support an interrupt controller or otherwise cannot support +# APIs like up_enable_irq() and up_disable_irq(). +# CONFIG_ARCH_VECNOTIRQ - Usually the interrupt vector number provided +# to interfaces like irq_attach() and irq_detach are the same as IRQ +# numbers that are provied to IRQ management functions like +# up_enable_irq() and up_disable_irq(). But that is not true for all +# interrupt controller implementations. For example, the PIC32MX +# interrupt controller manages interrupt sources that have a many-to-one +# relationship to interrupt vectors. In such cases, CONFIG_ARCH_VECNOTIRQ +# must defined so that the OS logic will know not to assume it can use +# a vector number to enable or disable interrupts. +# CONFIG_ARCH_IRQPRIO - The PIC32MX supports interrupt prioritization +# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt +# stack. If defined, this symbol is the size of the interrupt +# stack in bytes. If not defined, the user task stacks will be +# used during interrupt handling. +# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions +# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. +# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. +# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. +# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that +# cause a 100 second delay during boot-up. This 100 second delay +# serves no purpose other than it allows you to calibrate +# CONFIG_ARCH_DMA - Support DMA initialization +# +CONFIG_ARCH=mips +CONFIG_ARCH_MIPS=y +CONFIG_ARCH_MIPS32=y +CONFIG_ARCH_CHIP=pic32mx +CONFIG_ARCH_CHIP_PIC32MX795F512L=y +CONFIG_ARCH_BOARD=pic32-starterkit +CONFIG_ARCH_BOARD_PIC32_STARTERKIT=y +CONFIG_BOARD_LOOPSPERMSEC=7245 +CONFIG_DRAM_SIZE=(128*1024) +CONFIG_DRAM_START=0xa0000000 +CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE) +CONFIG_ARCH_NOINTC=n +CONFIG_ARCH_VECNOTIRQ=y +CONFIG_ARCH_IRQPRIO=y +CONFIG_ARCH_INTERRUPTSTACK=n +CONFIG_ARCH_STACKDUMP=y +CONFIG_ARCH_BOOTLOADER=n +CONFIG_ARCH_LEDS=y +CONFIG_ARCH_BUTTONS=n +CONFIG_ARCH_CALIBRATION=n +CONFIG_ARCH_DMA=n + +# +# Enable support for RAM-based functions +# (If selected, then modifications are needed in ld.script as well) +# +CONFIG_PIC32MX_RAMFUNCS=n + +# +# Identify toolchain and linker options +# +CONFIG_PIC32MX_MICROCHIPW=n +CONFIG_PIC32MX_MICROCHIPL=n +CONFIG_PIC32MX_MICROCHIPW_LITE=y +CONFIG_PIC32MX_MICROCHIPL_LITE=n + +# +# Individual subsystems can be enabled: +# + +CONFIG_PIC32MX_WDT=n +CONFIG_PIC32MX_RTCC=n +CONFIG_PIC32MX_TIMER1=n +CONFIG_PIC32MX_TIMER2=n +CONFIG_PIC32MX_TIMER3=n +CONFIG_PIC32MX_TIMER4=n +CONFIG_PIC32MX_TIMER5=n +CONFIG_PIC32MX_IC1=n +CONFIG_PIC32MX_IC2=n +CONFIG_PIC32MX_IC3=n +CONFIG_PIC32MX_IC4=n +CONFIG_PIC32MX_IC5=n +CONFIG_PIC32MX_OC1=n +CONFIG_PIC32MX_OC2=n +CONFIG_PIC32MX_OC3=n +CONFIG_PIC32MX_OC4=n +CONFIG_PIC32MX_OC5=n +CONFIG_PIC32MX_I2C1=n +CONFIG_PIC32MX_I2C2=n +CONFIG_PIC32MX_SPI1=n +CONFIG_PIC32MX_SPI2=n +CONFIG_PIC32MX_SPI3=n +CONFIG_PIC32MX_SPI4=n +CONFIG_PIC32MX_UART1=n +CONFIG_PIC32MX_UART2=n +CONFIG_PIC32MX_UART3=n +CONFIG_PIC32MX_UART4=n +CONFIG_PIC32MX_UART5=n +CONFIG_PIC32MX_UART6=n +CONFIG_PIC32MX_PMP=n +CONFIG_PIC32MX_ADC=n +CONFIG_PIC32MX_CVR=n +CONFIG_PIC32MX_CM1=n +CONFIG_PIC32MX_CM2=n +CONFIG_PIC32MX_OSC=y +CONFIG_PIC32MX_DDP=n +CONFIG_PIC32MX_FLASH=n +CONFIG_PIC32MX_BMX=n +CONFIG_PIC32MX_DMA=n +CONFIG_PIC32MX_CHE=n +CONFIG_PIC32MX_USBDEV=n +CONFIG_PIC32MX_USBHOST=n +CONFIG_PIC32MX_CAN1=n +CONFIG_PIC32MX_CAN2=n +CONFIG_PIC32MX_ETHERNET=y +CONFIG_PIC32MX_IOPORTA=y +CONFIG_PIC32MX_IOPORTB=y +CONFIG_PIC32MX_IOPORTC=y +CONFIG_PIC32MX_IOPORTD=y +CONFIG_PIC32MX_IOPORTE=y +CONFIG_PIC32MX_IOPORTF=y +CONFIG_PIC32MX_IOPORTG=y + +# +# PIC32MX Configuration Settings +# +# DEVCFG0: +# CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The +# value 2 enables. +# CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select +# Default 1 (PG2) +# CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled) +# CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled) +# CONFIG_PIC32MX_CODEWP - Default 1 (disabled) +# DEVCFG1: (All settings determined by selections in board.h) +# DEVCFG2: (All settings determined by selections in board.h) +# DEVCFG3: +# CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled +# (USBID pin is controlled by the USB module), but 0 (GPIO) otherwise. +# CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled +# (VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise. +# CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog +# can be enabled later by software). +# CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit. 1 (or undefined)= +# Default Ethernet I/O Pins; 0=Alternate Ethernet I/O Pins +# CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit. 1 (or undefined) = MII +# enabled; 0=RMII enabled +# +CONFIG_PIC32MX_DEBUGGER=2 +CONFIG_PIC32MX_ICESEL=1 +CONFIG_PIC32MX_FETHIO=0 +CONFIG_PIC32MX_FMIIEN=0 + +# +# PIC32MX specific serial device driver settings +# +# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the +# console and ttys0 (default is the UART1). +# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. +# This specific the size of the receive buffer +# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before +# being sent. This specific the size of the transmit buffer +# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be +# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. +# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity +# CONFIG_UARTn_2STOP - Two stop bits +# +CONFIG_UART1_SERIAL_CONSOLE=n +CONFIG_UART2_SERIAL_CONSOLE=n +CONFIG_UART3_SERIAL_CONSOLE=n +CONFIG_UART4_SERIAL_CONSOLE=n +CONFIG_UART5_SERIAL_CONSOLE=n +CONFIG_UART6_SERIAL_CONSOLE=n + +CONFIG_UART1_TXBUFSIZE=256 +CONFIG_UART2_TXBUFSIZE=256 +CONFIG_UART3_TXBUFSIZE=256 +CONFIG_UART4_TXBUFSIZE=256 +CONFIG_UART5_TXBUFSIZE=256 +CONFIG_UART6_TXBUFSIZE=256 + +CONFIG_UART1_RXBUFSIZE=256 +CONFIG_UART2_RXBUFSIZE=256 +CONFIG_UART3_RXBUFSIZE=256 +CONFIG_UART4_RXBUFSIZE=256 +CONFIG_UART5_RXBUFSIZE=256 +CONFIG_UART6_RXBUFSIZE=256 + +CONFIG_UART1_BAUD=115200 +CONFIG_UART2_BAUD=115200 +CONFIG_UART3_BAUD=115200 +CONFIG_UART4_BAUD=115200 +CONFIG_UART5_BAUD=115200 +CONFIG_UART6_BAUD=115200 + +CONFIG_UART1_BITS=8 +CONFIG_UART2_BITS=8 +CONFIG_UART3_BITS=8 +CONFIG_UART4_BITS=8 +CONFIG_UART5_BITS=8 +CONFIG_UART6_BITS=8 + +CONFIG_UART1_PARITY=0 +CONFIG_UART2_PARITY=0 +CONFIG_UART3_PARITY=0 +CONFIG_UART4_PARITY=0 +CONFIG_UART5_PARITY=0 +CONFIG_UART6_PARITY=0 + +CONFIG_UART1_2STOP=0 +CONFIG_UART2_2STOP=0 +CONFIG_UART3_2STOP=0 +CONFIG_UART4_2STOP=0 +CONFIG_UART5_2STOP=0 +CONFIG_UART6_2STOP=0 + +# +# PIC32MX specific PHY/Ethernet device driver settings +# +# CONFIG_PHY_KS8721 - Selects the Micrel KS8721 PHY +# CONFIG_PHY_DP83848C - Selects the National Semiconduction DP83848C PHY +# CONFIG_PHY_LAN8720 - Selects the SMSC LAN8720 PHY +# CONFIG_PHY_AUTONEG - Enable auto-negotion +# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. +# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex +# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 2 +# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 4 +# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is +# the higest priority. +# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). +# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets. +# Also needs CONFIG_DEBUG. +# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs +# CONFIG_DEBUG. Automatically enables CONFIG_NET_DESCDEBUG as well. +# CONFIG_NET_DESCDEBUG - Enabled low level descriptor debug. Also needs +# CONFIG_DEBUG. +# CONFIG_NET_DUMPPACKET - Dump all incoming and output packet contents. +# Also needs CONFIG_DEBUG. +# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. +# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. +# Automatically set if CONFIG_NET_IGMP is selected. +# +# Related DEVCFG3 Configuration Settings: +# CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit. 1 (or undefined)= +# Default Ethernet I/O Pins; 0=Alternate Ethernet I/O Pins +# CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit. 1 (or undefined) = MII +# enabled; 0=RMII enabled +# +CONFIG_PHY_KS8721=n +CONFIG_PHY_DP83848C=y +CONFIG_PHY_LAN8720=n +CONFIG_PHY_AUTONEG=y +CONFIG_PHY_SPEED100=n +CONFIG_PHY_FDUPLEX=y +CONFIG_NET_NTXDESC=7 +CONFIG_NET_NRXDESC=7 +CONFIG_NET_REGDEBUG=n +CONFIG_NET_DESCDEBUG=n +CONFIG_NET_DUMPPACKET=n + +# +# PIC32MX-specific USB device setup +# +CONFIG_PIC32MX_USBDEV_REGDEBUG=n +CONFIG_PIC32MX_USBDEV_BDTDEBUG=n + +# +# General build options +# +# CONFIG_RRLOAD_BINARY - make the rrload binary format used with +# BSPs from www.ridgerun.com using the tools/mkimage.sh script +# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_RAW_BINARY - make a raw binary format file used with many +# different loaders using the GNU objcopy program. This option +# should not be selected if you are not using the GNU toolchain. +# CONFIG_HAVE_LIBM - toolchain supports libm.a +# +CONFIG_RRLOAD_BINARY=n +CONFIG_INTELHEX_BINARY=y +CONFIG_MOTOROLA_SREC=n +CONFIG_RAW_BINARY=n +CONFIG_HAVE_LIBM=n + +# +# General OS setup +# +# CONFIG_APPS_DIR - Identifies the relative path to the directory +# that builds the application to link with NuttX. Default: ../apps +# CONFIG_DEBUG - enables built-in debug options +# CONFIG_DEBUG_VERBOSE - enables verbose debug output +# CONFIG_DEBUG_SYMBOLS - build without optimization and with +# debug symbols (needed for use with a debugger). +# CONFIG_HAVE_CXX - Enable support for C++ +# CONFIG_HAVE_CXXINITIALIZE - The platform-specific logic includes support +# for initialization of static C++ instances for this architecture +# and for the selected toolchain (via up_cxxinitialize()). +# CONFIG_MM_REGIONS - If the architecture includes multiple +# regions of memory to allocate from, this specifies the +# number of memory regions that the memory manager must +# handle and enables the API mm_addregion(start, end); +# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot +# time console output +# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz +# or MSEC_PER_TICK=10. This setting may be defined to +# inform NuttX that the processor hardware is providing +# system timer interrupts at some interrupt interval other +# than 10 msec. +# CONFIG_RR_INTERVAL - The round robin timeslice will be set +# this number of milliseconds; Round robin scheduling can +# be disabled by setting this value to zero. +# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in +# scheduler to monitor system performance +# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a +# task name to save in the TCB. Useful if scheduler +# instrumentation is selected. Set to zero to disable. +# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - +# Used to initialize the internal time logic. +# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. +# You would only need this if you are concerned about accurate +# time conversions in the past or in the distant future. +# CONFIG_JULIAN_TIME - Enables Julian time conversions. You +# would only need this if you are concerned about accurate +# time conversion in the distand past. You must also define +# CONFIG_GREGORIAN_TIME in order to use Julian time. +# CONFIG_DEV_CONSOLE - Set if architecture-specific logic +# provides /dev/console. Enables stdout, stderr, stdin. +# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console +# driver (minimul support) +# CONFIG_MUTEX_TYPES: Set to enable support for recursive and +# errorcheck mutexes. Enables pthread_mutexattr_settype(). +# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority +# inheritance on mutexes and semaphores. +# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority +# inheritance is enabled. It defines the maximum number of +# different threads (minus one) that can take counts on a +# semaphore with priority inheritance support. This may be +# set to zero if priority inheritance is disabled OR if you +# are only using semaphores as mutexes (only one holder) OR +# if no more than two threads participate using a counting +# semaphore. +# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, +# then this setting is the maximum number of higher priority +# threads (minus 1) than can be waiting for another thread +# to release a count on a semaphore. This value may be set +# to zero if no more than one thread is expected to wait for +# a semaphore. +# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors +# by task_create() when a new task is started. If set, all +# files/drivers will appear to be closed in the new task. +# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first +# three file descriptors (stdin, stdout, stderr) by task_create() +# when a new task is started. If set, all files/drivers will +# appear to be closed in the new task except for stdin, stdout, +# and stderr. +# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket +# desciptors by task_create() when a new task is started. If +# set, all sockets will appear to be closed in the new task. +# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to +# handle delayed processing from interrupt handlers. This feature +# is required for some drivers but, if there are not complaints, +# can be safely disabled. The worker thread also performs +# garbage collection -- completing any delayed memory deallocations +# from interrupt handlers. If the worker thread is disabled, +# then that clean will be performed by the IDLE thread instead +# (which runs at the lowest of priority and may not be appropriate +# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE +# is enabled, then the following options can also be used: +# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker +# thread. Default: 50 +# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for +# work in units of microseconds. Default: 50*1000 (50 MS). +# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker +# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. +# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up +# the worker thread. Default: 4 +# CONFIG_SCHED_WAITPID - Enable the waitpid() API +# CONFIG_SCHED_ATEXIT - Enabled the atexit() API +# +#CONFIG_APPS_DIR= + +CONFIG_DEBUG=n +CONFIG_DEBUG_VERBOSE=n +CONFIG_DEBUG_SYMBOLS=n +CONFIG_DEBUG_SCHED=n +CONFIG_DEBUG_USB=n +CONFIG_DEBUG_NET=n + +CONFIG_HAVE_CXX=n +CONFIG_HAVE_CXXINITIALIZE=n +CONFIG_MM_REGIONS=1 +CONFIG_ARCH_LOWPUTC=y +CONFIG_RR_INTERVAL=200 +CONFIG_SCHED_INSTRUMENTATION=n +CONFIG_TASK_NAME_SIZE=0 +CONFIG_START_YEAR=2012 +CONFIG_START_MONTH=3 +CONFIG_START_DAY=7 +CONFIG_GREGORIAN_TIME=n +CONFIG_JULIAN_TIME=n +CONFIG_DEV_CONSOLE=y +CONFIG_DEV_LOWCONSOLE=n +CONFIG_MUTEX_TYPES=n +CONFIG_PRIORITY_INHERITANCE=n +CONFIG_SEM_PREALLOCHOLDERS=0 +CONFIG_SEM_NNESTPRIO=0 +CONFIG_FDCLONE_DISABLE=n +CONFIG_FDCLONE_STDIO=n +CONFIG_SDCLONE_DISABLE=y +CONFIG_SCHED_WORKQUEUE=n +CONFIG_SCHED_WORKPRIORITY=192 +CONFIG_SCHED_WORKPERIOD=(50*1000) +CONFIG_SCHED_WORKSTACKSIZE=1024 +CONFIG_SIG_SIGWORK=4 +CONFIG_SCHED_WAITPID=y +CONFIG_SCHED_ATEXIT=n + +# +# System Logging +# +# CONFIG_SYSLOG - Enables the System Logging feature. +# CONFIG_RAMLOG - Enables the RAM logging feature +# CONFIG_RAMLOG_CONSOLE - Use the RAM logging device as a system console. +# If this feature is enabled (along with CONFIG_DEV_CONSOLE), then all +# console output will be re-directed to a circular buffer in RAM. This +# is useful, for example, if the only console is a Telnet console. Then +# in that case, console output from non-Telnet threads will go to the +# circular buffer and can be viewed using the NSH 'dmesg' command. +# CONFIG_RAMLOG_SYSLOG - Use the RAM logging device for the syslogging +# interface. If this feature is enabled (along with CONFIG_SYSLOG), +# then all debug output (only) will be re-directed to the circular +# buffer in RAM. This RAM log can be view from NSH using the 'dmesg' +# command. +# CONFIG_RAMLOG_NPOLLWAITERS - The number of threads than can be waiting +# for this driver on poll(). Default: 4 +# +# If CONFIG_RAMLOG_CONSOLE or CONFIG_RAMLOG_SYSLOG is selected, then the +# following may also be provided: +# +# CONFIG_RAMLOG_CONSOLE_BUFSIZE - Size of the console RAM log. Default: 1024 +# + +CONFIG_SYSLOG=y +CONFIG_RAMLOG=y +CONFIG_RAMLOG_CONSOLE=n +CONFIG_RAMLOG_SYSLOG=y +#CONFIG_RAMLOG_NPOLLWAITERS +CONFIG_RAMLOG_CONSOLE_BUFSIZE=16384 + +# +# Settings for NXFLAT +# +# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. +# This format will support execution of NuttX binaries located +# in a ROMFS filesystem (see examples/nxflat). +# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals +# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and +# CONFIG_DEBUG_BINFMT have to be defined or +# CONFIG_NXFLAT_DUMPBUFFER does nothing. +# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table +# is ordered by symbol name +# +CONFIG_NXFLAT=n +CONFIG_NXFLAT_DUMPBUFFER=n +CONFIG_SYMTAB_ORDEREDBYNAME=y + +# +# The following can be used to disable categories of +# APIs supported by the OS. If the compiler supports +# weak functions, then it should not be necessary to +# disable functions unless you want to restrict usage +# of those APIs. +# +# There are certain dependency relationships in these +# features. +# +# o mq_notify logic depends on signals to awaken tasks +# waiting for queues to become full or empty. +# o pthread_condtimedwait() depends on signals to wake +# up waiting tasks. +# +CONFIG_DISABLE_CLOCK=n +CONFIG_DISABLE_POSIX_TIMERS=n +CONFIG_DISABLE_PTHREAD=n +CONFIG_DISABLE_SIGNALS=n +CONFIG_DISABLE_MQUEUE=n +CONFIG_DISABLE_MOUNTPOINT=n +CONFIG_DISABLE_ENVIRON=n +CONFIG_DISABLE_POLL=n + +# +# Misc libc settings +# +# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a +# little smaller if we do not support fieldwidthes +# +CONFIG_NOPRINTF_FIELDWIDTH=n + +# +# Allow for architecture optimized implementations +# +# The architecture can provide optimized versions of the +# following to improve system performance +# +CONFIG_ARCH_MEMCPY=n +CONFIG_ARCH_MEMCMP=n +CONFIG_ARCH_MEMMOVE=n +CONFIG_ARCH_MEMSET=n +CONFIG_ARCH_STRCMP=n +CONFIG_ARCH_STRCPY=n +CONFIG_ARCH_STRNCPY=n +CONFIG_ARCH_STRLEN=n +CONFIG_ARCH_STRNLEN=n +CONFIG_ARCH_BZERO=n + +# +# Sizes of configurable things (0 disables) +# +# CONFIG_MAX_TASKS - The maximum number of simultaneously +# active tasks. This value must be a power of two. +# CONFIG_MAX_TASK_ARGS - This controls the maximum number of +# of parameters that a task may receive (i.e., maxmum value +# of 'argc') +# CONFIG_NPTHREAD_KEYS - The number of items of thread- +# specific data that can be retained +# CONFIG_NFILE_DESCRIPTORS - The maximum number of file +# descriptors (one for each open) +# CONFIG_NFILE_STREAMS - The maximum number of streams that +# can be fopen'ed +# CONFIG_NAME_MAX - The maximum size of a file name. +# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate +# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled +# (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added +# to force automatic, line-oriented flushing the output buffer +# for putc(), fputc(), putchar(), puts(), fputs(), printf(), +# fprintf(), and vfprintf(). When a newline is encountered in +# the output string, the output buffer will be flushed. This +# (slightly) increases the NuttX footprint but supports the kind +# of behavior that people expect for printf(). +# CONFIG_NUNGET_CHARS - Number of characters that can be +# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message +# structures. The system manages a pool of preallocated +# message structures to minimize dynamic allocations +# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with +# a fixed payload size given by this settin (does not include +# other message structure overhead. +# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that +# can be passed to a watchdog handler +# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog +# structures. The system manages a pool of preallocated +# watchdog structures to minimize dynamic allocations +# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX +# timer structures. The system manages a pool of preallocated +# timer structures to minimize dynamic allocations. Set to +# zero for all dynamic allocations. +# +CONFIG_MAX_TASKS=16 +CONFIG_MAX_TASK_ARGS=4 +CONFIG_NPTHREAD_KEYS=4 +CONFIG_NFILE_DESCRIPTORS=8 +CONFIG_NFILE_STREAMS=8 +CONFIG_NAME_MAX=32 +CONFIG_STDIO_BUFFER_SIZE=128 +CONFIG_STDIO_LINEBUFFER=y +CONFIG_NUNGET_CHARS=2 +CONFIG_PREALLOC_MQ_MSGS=4 +CONFIG_MQ_MAXMSGSIZE=32 +CONFIG_MAX_WDOGPARMS=2 +CONFIG_PREALLOC_WDOGS=16 +CONFIG_PREALLOC_TIMERS=4 + +# +# Framebuffer driver options +# +CONFIG_FB_CMAP=n +CONFIG_FB_HWCURSOR=n +CONFIG_FB_HWCURSORIMAGE=n +#CONFIG_FB_HWCURSORSIZE +#CONFIG_FB_TRANSPARENCY + +# +# Filesystem configuration +# +# CONFIG_FS_FAT - Enable FAT filesystem support +# CONFIG_FAT_SECTORSIZE - Max supported sector size +# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 +# file name support. +# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims +# patents on FAT long file name technology. Please read the +# disclaimer in the top-level COPYING file and only enable this +# feature if you understand these issues. +# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the +# default, maximum long file name is 255 bytes. This can eat up +# a lot of memory (especially stack space). If you are willing +# to live with some non-standard, short long file names, then +# define this value. A good choice would be the same value as +# selected for CONFIG_NAME_MAX which will limit the visibility +# of longer file names anyway. +# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. +# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. +# This must have one of the values of 0xff or 0x00. +# Default: 0xff. +# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, +# don't both with file chunks smaller than this number of data bytes. +# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. +# Default: 255. +# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, +# don't both with file chunks smaller than this number of data bytes. +# Default: 32. +# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean +# packing files together toward the end of the file or, if file are +# deleted at the end of the file, clean up can simply mean erasing +# the end of FLASH memory so that it can be re-used again. However, +# doing this can also harm the life of the FLASH part because it can +# mean that the tail end of the FLASH is re-used too often. This +# threshold determines if/when it is worth erased the tail end of FLASH +# and making it available for re-use (and possible over-wear). +# Default: 8192. +# CONFIG_FS_ROMFS - Enable ROMFS filesystem support +# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this +# option will enable a limited form of memory mapping that is +# implemented by copying whole files into memory. +# +CONFIG_FS_FAT=y +CONFIG_FAT_LCNAMES=y +CONFIG_FAT_LFN=y +CONFIG_FAT_MAXFNAME=32 +CONFIG_FS_NXFFS=n +CONFIG_FS_ROMFS=n + +# +# SPI-based MMC/SD driver +# +# CONFIG_MMCSD_NSLOTS +# Number of MMC/SD slots supported by the driver +# CONFIG_MMCSD_READONLY +# Provide read-only access (default is read/write) +# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. +# Default is 20MHz. +# +CONFIG_MMCSD_NSLOTS=1 +CONFIG_MMCSD_READONLY=n +CONFIG_MMCSD_SPICLOCK=12500000 + +# +# Block driver buffering +# +# CONFIG_FS_READAHEAD +# Enable read-ahead buffering +# CONFIG_FS_WRITEBUFFER +# Enable write buffering +# +CONFIG_FS_READAHEAD=n +CONFIG_FS_WRITEBUFFER=n + +# +# SDIO-based MMC/SD driver +# +# CONFIG_SDIO_DMA +# SDIO driver supports DMA +# CONFIG_MMCSD_MMCSUPPORT +# Enable support for MMC cards +# CONFIG_MMCSD_HAVECARDDETECT +# SDIO driver card detection is 100% accurate +# +CONFIG_SDIO_DMA=n +CONFIG_MMCSD_MMCSUPPORT=n +CONFIG_MMCSD_HAVECARDDETECT=n + +# +# TCP/IP and UDP support via uIP +# CONFIG_NET - Enable or disable all network features +# CONFIG_NET_NOINTS -- CONFIG_NET_NOINT indicates that uIP not called from +# the interrupt level. If CONFIG_NET_NOINTS is defined, critical sections +# will be managed with semaphores; Otherwise, it assumed that uIP will be +# called from interrupt level handling and critical sections will be +# managed by enabling and disabling interrupts. +# CONFIG_NET_MULTIBUFFER - Traditionally, uIP has used a single buffer +# for all incoming and outgoing traffic. If this configuration is +# selected, then the driver can manage multiple I/O buffers and can, +# for example, be filling one input buffer while sending another +# output buffer. Or, as another example, the driver may support +# queuing of concurrent input/ouput and output transfers for better +# performance. +# CONFIG_NET_IPv6 - Build in support for IPv6 +# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. +# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options +# CONFIG_NET_BUFSIZE - uIP buffer size +# CONFIG_NET_TCP - TCP support on or off +# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) +# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers +# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) +# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until +# accept() is called. The size of the backlog is selected when listen() is called. +# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) +# CONFIG_NET_UDP - UDP support on or off +# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off +# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections +# CONFIG_NET_ICMP - ICMP ping response support on or off +# CONFIG_NET_ICMP_PING - ICMP ping request support on or off +# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address +# CONFIG_NET_STATISTICS - uIP statistics on or off +# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window +# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table +# CONFIG_NET_BROADCAST - Broadcast support +# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates +# +CONFIG_NET=y +CONFIG_NET_NOINTS=n +CONFIG_NET_MULTIBUFFER=y +CONFIG_NET_IPv6=n +CONFIG_NSOCKET_DESCRIPTORS=10 +CONFIG_NET_SOCKOPTS=y +CONFIG_NET_BUFSIZE=562 +CONFIG_NET_TCP=y +CONFIG_NET_TCP_CONNS=40 +#CONFIG_NET_TCP_READAHEAD_BUFSIZE +CONFIG_NET_NTCP_READAHEAD_BUFFERS=16 +CONFIG_NET_TCPBACKLOG=y +CONFIG_NET_MAX_LISTENPORTS=40 +CONFIG_NET_UDP=y +CONFIG_NET_UDP_CHECKSUMS=y +#CONFIG_NET_UDP_CONNS=10 +CONFIG_NET_ICMP=y +CONFIG_NET_ICMP_PING=y +#CONFIG_NET_PINGADDRCONF=0 +CONFIG_NET_STATISTICS=n +#CONFIG_NET_RECEIVE_WINDOW= +CONFIG_NET_BROADCAST=n +#CONFIG_NET_ARPTAB_SIZE=8 +CONFIG_NET_ARP_IPIN=n +CONFIG_NET_MULTICAST=n +#CONFIG_NET_FWCACHE_SIZE=2 + +# +# UIP Network Utilities +# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP +# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries +# +CONFIG_NET_DHCP_LIGHT=n +CONFIG_NET_RESOLV_ENTRIES=4 + +# +# FTP Server +# +# CONFIG_FTPD_VENDORID - The vendor name to use in FTP communications. +# Default: "NuttX" +# CONFIG_FTPD_SERVERID - The server name to use in FTP communications. +# Default: "NuttX FTP Server" +# CONFIG_FTPD_CMDBUFFERSIZE - The maximum size of one command. Default: +# 128 bytes. +# CONFIG_FTPD_DATABUFFERSIZE - The size of the I/O buffer for data +# transfers. Default: 512 bytes. +# CONFIG_FTPD_WORKERSTACKSIZE - The stacksize to allocate for each +# FTP daemon worker thread. Default: 2048 bytes. +# +# Other required configuration settings: Of course TCP networking support +# is required. But here are a couple that are less obvious: +# +# CONFIG_DISABLE_PTHREAD - pthread support is required +# CONFIG_DISABLE_POLL - poll() support is required +# +CONFIG_FTPD_CMDBUFFERSIZE=512 +CONFIG_FTPD_DATABUFFERSIZE=2048 + +# +# USB Device Configuration +# +# CONFIG_USBDEV +# Enables USB device support +# CONFIG_USBDEV_ISOCHRONOUS +# Build in extra support for isochronous endpoints +# CONFIG_USBDEV_DUALSPEED +# Hardware handles high and full speed operation (USB 2.0) +# CONFIG_USBDEV_SELFPOWERED +# Will cause USB features to indicate that the device is +# self-powered +# CONFIG_USBDEV_MAXPOWER +# Maximum power consumption in mA +# CONFIG_USBDEV_TRACE +# Enables USB tracing for debug +# CONFIG_USBDEV_TRACE_NRECORDS +# Number of trace entries to remember +# +CONFIG_USBDEV=n +CONFIG_USBDEV_ISOCHRONOUS=n +CONFIG_USBDEV_DUALSPEED=n +CONFIG_USBDEV_SELFPOWERED=y +CONFIG_USBDEV_REMOTEWAKEUP=n +CONFIG_USBDEV_MAXPOWER=100 +CONFIG_USBDEV_TRACE=n +CONFIG_USBDEV_TRACE_NRECORDS=128 + +# +# USB Serial Device Configuration +# +# CONFIG_PL2303 +# Enable compilation of the USB serial driver +# CONFIG_PL2303_EPINTIN +# The logical 7-bit address of a hardware endpoint that supports +# interrupt IN operation +# CONFIG_PL2303_EPBULKOUT +# The logical 7-bit address of a hardware endpoint that supports +# bulk OUT operation +# CONFIG_PL2303_EPBULKIN +# The logical 7-bit address of a hardware endpoint that supports +# bulk IN operation +# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR +# The vendor ID code/string +# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR +# The product ID code/string +# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE +# Size of the serial receive/transmit buffers +# +CONFIG_PL2303=n +CONFIG_PL2303_EPINTIN=1 +CONFIG_PL2303_EPBULKOUT=2 +CONFIG_PL2303_EPBULKIN=5 +CONFIG_PL2303_NWRREQS=4 +CONFIG_PL2303_NRDREQS=4 +CONFIG_PL2303_VENDORID=0x067b +CONFIG_PL2303_PRODUCTID=0x2303 +CONFIG_PL2303_VENDORSTR="Nuttx" +CONFIG_PL2303_PRODUCTSTR="USBdev Serial" +CONFIG_PL2303_RXBUFSIZE=512 +CONFIG_PL2303_TXBUFSIZE=512 + +# +# USB serial device class driver (Standard CDC ACM class) +# +# CONFIG_CDCACM +# Enable compilation of the USB serial driver +# CONFIG_CDCACM_CONSOLE +# Configures the CDC/ACM serial port as the console device. +# CONFIG_CDCACM_EP0MAXPACKET +# Endpoint 0 max packet size. Default 64 +# CONFIG_CDCACM_EPINTIN +# The logical 7-bit address of a hardware endpoint that supports +# interrupt IN operation. Default 2. +# CONFIG_CDCACM_EPINTIN_FSSIZE +# Max package size for the interrupt IN endpoint if full speed mode. +# Default 64. +# CONFIG_CDCACM_EPINTIN_HSSIZE +# Max package size for the interrupt IN endpoint if high speed mode. +# Default 64 +# CONFIG_CDCACM_EPBULKOUT +# The logical 7-bit address of a hardware endpoint that supports +# bulk OUT operation +# CONFIG_CDCACM_EPBULKOUT_FSSIZE +# Max package size for the bulk OUT endpoint if full speed mode. +# Default 64. +# CONFIG_CDCACM_EPBULKOUT_HSSIZE +# Max package size for the bulk OUT endpoint if high speed mode. +# Default 512. +# CONFIG_CDCACM_EPBULKIN +# The logical 7-bit address of a hardware endpoint that supports +# bulk IN operation +# CONFIG_CDCACM_EPBULKIN_FSSIZE +# Max package size for the bulk IN endpoint if full speed mode. +# Default 64. +# CONFIG_CDCACM_EPBULKIN_HSSIZE +# Max package size for the bulk IN endpoint if high speed mode. +# Default 512. +# CONFIG_CDCACM_NWRREQS and CONFIG_CDCACM_NRDREQS +# The number of write/read requests that can be in flight. +# Default 256. +# CONFIG_CDCACM_VENDORID and CONFIG_CDCACM_VENDORSTR +# The vendor ID code/string. Default 0x0525 and "NuttX" +# 0x0525 is the Netchip vendor and should not be used in any +# products. This default VID was selected for compatibility with +# the Linux CDC ACM default VID. +# CONFIG_CDCACM_PRODUCTID and CONFIG_CDCACM_PRODUCTSTR +# The product ID code/string. Default 0xara7 and "CDC/ACM Serial" +# 0xa4a7 was selected for compatibility with the Linux CDC ACM +# default PID. +# CONFIG_CDCACM_RXBUFSIZE and CONFIG_CDCACM_TXBUFSIZE +# Size of the serial receive/transmit buffers. Default 256. +# +CONFIG_CDCACM=n +CONFIG_CDCACM_CONSOLE=n +#CONFIG_CDCACM_EP0MAXPACKET +#CONFIG_CDCACM_EPINTIN +#CONFIG_CDCACM_EPINTIN_FSSIZE +#CONFIG_CDCACM_EPINTIN_HSSIZE +#CONFIG_CDCACM_EPBULKOUT +#CONFIG_CDCACM_EPBULKOUT_FSSIZE +#CONFIG_CDCACM_EPBULKOUT_HSSIZE +#CONFIG_CDCACM_EPBULKIN +#CONFIG_CDCACM_EPBULKIN_FSSIZE +#CONFIG_CDCACM_EPBULKIN_HSSIZE +#CONFIG_CDCACM_NWRREQS +#CONFIG_CDCACM_NRDREQS +#CONFIG_CDCACM_VENDORID +#CONFIG_CDCACM_VENDORSTR +#CONFIG_CDCACM_PRODUCTID +#CONFIG_CDCACM_PRODUCTSTR +#CONFIG_CDCACM_RXBUFSIZE +#CONFIG_CDCACM_TXBUFSIZE + +# +# USB Storage Device Configuration +# +# CONFIG_USBMSC +# Enable compilation of the USB storage driver +# CONFIG_USBMSC_EP0MAXPACKET +# Max packet size for endpoint 0 +# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN +# The logical 7-bit address of a hardware endpoints that support +# bulk OUT and IN operations +# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN +# The size of the buffer in each write/read request. This +# value needs to be at least as large as the endpoint +# maxpacket and ideally as large as a block device sector. +# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR +# The vendor ID code/string +# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR +# The product ID code/string +# CONFIG_USBMSC_REMOVABLE +# Select if the media is removable +# +CONFIG_USBMSC=n +CONFIG_USBMSC_EP0MAXPACKET=64 +CONFIG_USBMSC_EPBULKOUT=2 +CONFIG_USBMSC_EPBULKIN=5 +CONFIG_USBMSC_NRDREQS=2 +CONFIG_USBMSC_NWRREQS=2 +CONFIG_USBMSC_BULKINREQLEN=256 +CONFIG_USBMSC_BULKOUTREQLEN=256 +CONFIG_USBMSC_VENDORID=0x584e +CONFIG_USBMSC_VENDORSTR="NuttX" +CONFIG_USBMSC_PRODUCTID=0x5342 +CONFIG_USBMSC_PRODUCTSTR="USBdev Storage" +CONFIG_USBMSC_VERSIONNO=0x0399 +CONFIG_USBMSC_REMOVABLE=y + +# +# Graphics related configuration settings +# +# CONFIG_NX +# Enables overall support for graphics library and NX +# CONFIG_NX_MULTIUSER +# Configures NX in multi-user mode +# CONFIG_NX_NPLANES +# Some YUV color formats requires support for multiple planes, +# one for each color component. Unless you have such special +# hardware, this value should be undefined or set to 1 +# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP, +# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP, +# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and +# CONFIG_NX_DISABLE_32BPP +# NX supports a variety of pixel depths. You can save some +# memory by disabling support for unused color depths. +# CONFIG_NX_PACKEDMSFIRST +# If a pixel depth of less than 8-bits is used, then NX needs +# to know if the pixels pack from the MS to LS or from LS to MS +# CONFIG_NX_LCDDRIVER +# By default, NX builds to use a framebuffer driver (see +# include/nuttx/fb.h). If this option is defined, NX will +# build to use an LCD driver (see include/nuttx/lcd/lcd.h). +# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device. +# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device. +# CONFIG_NX_MOUSE +# Build in support for mouse input +# CONFIG_NX_KBD +# Build in support of keypad/keyboard input +# CONFIG_NXTK_BORDERWIDTH +# Specifies with with of the border (in pixels) used with +# framed windows. The default is 4. +# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2 +# Specify the colors of the border used with framed windows. +# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so +# is normally darker. The default is medium and dark grey, +# respectively +# CONFIG_NXTK_AUTORAISE +# If set, a window will be raised to the top if the mouse position +# is over a visible portion of the window. Default: A mouse +# button must be clicked over a visible portion of the window. +# CONFIG_NXFONTS_CHARBITS +# The number of bits in the character set. Current options are +# only 7 and 8. The default is 7. +# CONFIG_NXFONT_SANS17X22 +# This option enables support for a tiny, 17x22 san serif font +# (font ID FONTID_SANS17X22 == 14). +# CONFIG_NXFONT_SANS20X26 +# This option enables support for a tiny, 20x26 san serif font +# (font ID FONTID_SANS20X26 == 15). +# CONFIG_NXFONT_SANS23X27 +# This option enables support for a tiny, 23x27 san serif font +# (font ID FONTID_SANS23X27 == 1). +# CONFIG_NXFONT_SANS22X29 +# This option enables support for a small, 22x29 san serif font +# (font ID FONTID_SANS22X29 == 2). +# CONFIG_NXFONT_SANS28X37 +# This option enables support for a medium, 28x37 san serif font +# (font ID FONTID_SANS28X37 == 3). +# CONFIG_NXFONT_SANS39X48 +# This option enables support for a large, 39x48 san serif font +# (font ID FONTID_SANS39X48 == 4). +# CONFIG_NXFONT_SANS17X23B +# This option enables support for a tiny, 17x23 san serif bold font +# (font ID FONTID_SANS17X23B == 16). +# CONFIG_NXFONT_SANS20X27B +# This option enables support for a tiny, 20x27 san serif bold font +# (font ID FONTID_SANS20X27B == 17). +# CONFIG_NXFONT_SANS22X29B +# This option enables support for a small, 22x29 san serif bold font +# (font ID FONTID_SANS22X29B == 5). +# CONFIG_NXFONT_SANS28X37B +# This option enables support for a medium, 28x37 san serif bold font +# (font ID FONTID_SANS28X37B == 6). +# CONFIG_NXFONT_SANS40X49B +# This option enables support for a large, 40x49 san serif bold font +# (font ID FONTID_SANS40X49B == 7). +# CONFIG_NXFONT_SERIF22X29 +# This option enables support for a small, 22x29 font (with serifs) +# (font ID FONTID_SERIF22X29 == 8). +# CONFIG_NXFONT_SERIF29X37 +# This option enables support for a medium, 29x37 font (with serifs) +# (font ID FONTID_SERIF29X37 == 9). +# CONFIG_NXFONT_SERIF38X48 +# This option enables support for a large, 38x48 font (with serifs) +# (font ID FONTID_SERIF38X48 == 10). +# CONFIG_NXFONT_SERIF22X28B +# This option enables support for a small, 27x38 bold font (with serifs) +# (font ID FONTID_SERIF22X28B == 11). +# CONFIG_NXFONT_SERIF27X38B +# This option enables support for a medium, 27x38 bold font (with serifs) +# (font ID FONTID_SERIF27X38B == 12). +# CONFIG_NXFONT_SERIF38X49B +# This option enables support for a large, 38x49 bold font (with serifs) +# (font ID FONTID_SERIF38X49B == 13). +# +# NX Multi-user only options: +# +# CONFIG_NX_BLOCKING +# Open the client message queues in blocking mode. In this case, +# nx_eventhandler() will not return until a message is received and processed. +# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS +# Specifies the maximum number of messages that can fit in +# the message queues. No additional resources are allocated, but +# this can be set to prevent flooding of the client or server with +# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many +# messages are pre-allocated). +# +CONFIG_NX=n +CONFIG_NX_MULTIUSER=n +CONFIG_NX_NPLANES=1 +CONFIG_NX_DISABLE_1BPP=y +CONFIG_NX_DISABLE_2BPP=y +CONFIG_NX_DISABLE_4BPP=y +CONFIG_NX_DISABLE_8BPP=y +CONFIG_NX_DISABLE_16BPP=n +CONFIG_NX_DISABLE_24BPP=y +CONFIG_NX_DISABLE_32BPP=y +CONFIG_NX_PACKEDMSFIRST=n +CONFIG_NX_LCDDRIVER=y +CONFIG_LCD_MAXPOWER=1 +CONFIG_LCD_MAXCONTRAST=1 +CONFIG_NX_MOUSE=y +CONFIG_NX_KBD=y +#CONFIG_NXTK_BORDERWIDTH=4 +CONFIG_NXTK_BORDERCOLOR1=0xd69a +CONFIG_NXTK_BORDERCOLOR2=0xad55 +CONFIG_NXTK_AUTORAISE=n +CONFIG_NXFONT_SANS17X22=y +CONFIG_NXFONT_SANS20X26=n +CONFIG_NXFONT_SANS22X29=n +CONFIG_NXFONT_SANS23X27=n +CONFIG_NXFONT_SANS28X37=n +CONFIG_NXFONT_SANS17X23B=n +CONFIG_NXFONT_SANS20X27B=y +CONFIG_NXFONT_SANS22X29B=y +CONFIG_NXFONT_SANS28X37B=n +CONFIG_NXFONT_SANS40X49B=n +CONFIG_NXFONT_SERIF22X29=n +CONFIG_NXFONT_SERIF29X37=n +CONFIG_NXFONT_SERIF38X48=n +CONFIG_NXFONT_SERIF22X28B=n +CONFIG_NXFONT_SERIF27X38B=n +CONFIG_NXFONT_SERIF38X49B=n +CONFIG_NXFONTS_CHARBITS=7 +CONFIG_NX_BLOCKING=y +CONFIG_NX_MXSERVERMSGS=32 +CONFIG_NX_MXCLIENTMSGS=16 + +# +# Settings for examples/uip +# +CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_EXAMPLE_UIP_DHCPC=n + +# +# Settings for examples/nettest +# +# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act +# as either the client side or server side of the test +# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the +# client side simply receives messages forever, allowing +# measurement of throughput +# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has +# no MAC address; one will be assigned +# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address +# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address +# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask +# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the +# client side of the test (may be target or host) +# +CONFIG_EXAMPLE_NETTEST_SERVER=n +CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n +CONFIG_EXAMPLE_NETTEST_NOMAC=y +CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1) + +# +# Settings for examples/ostest +# +CONFIG_EXAMPLES_OSTEST_LOOPS=1 +CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048 +CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 + +# +# Settings for apps/nshlib +# +# CONFIG_NSH_BUILTIN_APPS - Support external registered, +# "named" applications that can be executed from the NSH +# command line (see apps/README.txt for more information). +# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer +# CONFIG_NSH_STRERROR - Use strerror(errno) +# CONFIG_NSH_LINELEN - Maximum length of one command line +# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi +# CONFIG_NSH_DISABLESCRIPT - Disable scripting support +# CONFIG_NSH_DISABLEBG - Disable background commands +# CONFIG_NSH_ROMFSETC - Use startup script in /etc +# CONFIG_NSH_CONSOLE - Use serial console front end +# CONFIG_NSH_TELNET - Use telnetd console front end +# CONFIG_NSH_ARCHINIT - Platform provides architecture +# specific initialization (nsh_archinitialize()). +# +# If CONFIG_NSH_TELNET is selected: +# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size +# CONFIG_NSH_DHCPC - Obtain address using DHCP +# CONFIG_NSH_IPADDR - Provides static IP address +# CONFIG_NSH_DRIPADDR - Provides static router IP address +# CONFIG_NSH_NETMASK - Provides static network mask +# CONFIG_NSH_NOMAC - Use a bogus MAC address +# +# If CONFIG_NSH_ROMFSETC is selected: +# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint +# CONFIG_NSH_INITSCRIPT - Relative path to init script +# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor +# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size +# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor +# CONFIG_NSH_FATSECTSIZE - FAT FS sector size +# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors +# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint +# +CONFIG_NSH_BUILTIN_APPS=y +CONFIG_NSH_FILEIOSIZE=512 +CONFIG_NSH_STRERROR=n +CONFIG_NSH_LINELEN=64 +CONFIG_NSH_NESTDEPTH=3 +CONFIG_NSH_DISABLESCRIPT=n +CONFIG_NSH_DISABLEBG=n +CONFIG_NSH_ROMFSETC=n +CONFIG_NSH_CONSOLE=y +CONFIG_NSH_TELNET=y +CONFIG_NSH_ARCHINIT=y +CONFIG_NSH_IOBUFFER_SIZE=512 +CONFIG_NSH_DHCPC=n +CONFIG_NSH_NOMAC=n +CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_NSH_ROMFSMOUNTPT="/etc" +CONFIG_NSH_INITSCRIPT="init.d/rcS" +CONFIG_NSH_ROMFSDEVNO=0 +CONFIG_NSH_ROMFSSECTSIZE=64 +CONFIG_NSH_FATDEVNO=1 +CONFIG_NSH_FATSECTSIZE=512 +CONFIG_NSH_FATNSECTORS=1024 +CONFIG_NSH_FATMOUNTPT=/tmp + +# +# Architecture-specific NSH options +# +CONFIG_NSH_MMCSDSPIPORTNO=1 +CONFIG_NSH_MMCSDSLOTNO=0 +CONFIG_NSH_MMCSDMINOR=0 + +# +# I2C tool settings +# +# CONFIG_I2CTOOL_BUILTIN - Build the tools as an NSH built-in command +# CONFIG_I2CTOOL_MINBUS - Smallest bus index supported by the hardware (default 0). +# CONFIG_I2CTOOL_MAXBUS - Largest bus index supported by the hardware (default 3) +# CONFIG_I2CTOOL_MINADDR - Minium device address (default: 0x03) +# CONFIG_I2CTOOL_MAXADDR - Largest device address (default: 0x77) +# CONFIG_I2CTOOL_MAXREGADDR - Largest register address (default: 0xff) +# CONFIG_I2CTOOL_DEFFREQ - Default frequency (default: 1000000) +# +CONFIG_I2CTOOL_BUILTIN=y +CONFIG_I2CTOOL_MINBUS=1 +CONFIG_I2CTOOL_MAXBUS=4 +#CONFIG_I2CTOOL_MINADDR +#CONFIG_I2CTOOL_MAXADDR +#CONFIG_I2CTOOL_MAXREGADDR +CONFIG_I2CTOOL_DEFFREQ=100000 + +# +# Settings for examples/ftpd +# +# CONFIG_EXAMPLES_FTPD_PRIO - Priority of the FTP daemon. +# Default: SCHED_PRIORITY_DEFAULT +# CONFIG_EXAMPLES_FTPD_STACKSIZE - Stack size allocated for the +# FTP daemon. Default: 2048 +# CONFIG_EXAMPLES_FTPD_NONETINIT - Define to suppress configuration of the +# network by apps/examples/ftpd. You would need to suppress network +# configuration if the network is configuration prior to running the +# example. +# +# NSH always initializes the network so if CONFIG_NSH_BUILTIN_APPS is +# defined, so is CONFIG_EXAMPLES_FTPD_NONETINIT (se it does not explicitly +# need to be defined in that case): +# +# CONFIG_NSH_BUILTIN_APPS - Build the FTPD daemon example test as an +# NSH built-in function. By default the FTPD daemon will be built +# as a standalone application. +# +# If CONFIG_EXAMPLES_FTPD_NONETINIT is not defined, then the following may +# be specified to customized the network configuration: +# +# CONFIG_EXAMPLE_FTPD_NOMAC - If the hardware has no MAC address of its +# own, define this =y to provide a bogus address for testing. +# CONFIG_EXAMPLE_FTPD_IPADDR - The target IP address. Default 10.0.0.2 +# CONFIG_EXAMPLE_FTPD_DRIPADDR - The default router address. Default +# 10.0.0.1 +# CONFIG_EXAMPLE_FTPD_NETMASK - The network mask. Default: 255.255.255.0 + +# +# Settings for examples/usbserial +# +# CONFIG_EXAMPLES_USBSERIAL_INONLY +# Only verify IN (device-to-host) data transfers. Default: both +# CONFIG_EXAMPLES_USBSERIAL_OUTONLY +# Only verify OUT (host-to-device) data transfers. Default: both +# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL +# Send only small, single packet messages. Default: Send large and small. +# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG +# Send only large, multi-packet messages. Default: Send large and small. +# +CONFIG_EXAMPLES_USBSERIAL_INONLY=n +CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n +CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n +CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n + +CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n +CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n +CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n +CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n +CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n + +# +# Settings for examples/usbstorage +# +# CONFIG_EXAMPLES_USBMSC_NLUNS +# Defines the number of logical units (LUNs) exported by the USB storage +# driver. Each LUN corresponds to one exported block driver (or partition +# of a block driver). May be 1, 2, or 3. Default is 1. +# CONFIG_EXAMPLES_USBMSC_DEVMINOR1 +# The minor device number of the block driver for the first LUN. For +# example, N in /dev/mmcsdN. Used for registering the block driver. Default +# is zero. +# CONFIG_EXAMPLES_USBMSC_DEVPATH1 +# The full path to the registered block driver. Default is "/dev/mmcsd0" +# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2 +# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS +# is 2 or 3. No defaults. +# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3 +# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS +# is 3. No defaults. +# +# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then +# the example code will also manage the USB trace output. The amount of trace output +# can be controlled using: +# +# CONFIG_EXAMPLES_USBMSC_TRACEINIT +# Show initialization events +# CONFIG_EXAMPLES_USBMSC_TRACECLASS +# Show class driver events +# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS +# Show data transfer events +# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER +# Show controller events +# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS +# Show interrupt-related events. +# +CONFIG_EXAMPLES_USBMSC_NLUNS=1 +CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0 +CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0" +CONFIG_EXAMPLES_USBMSC_TRACEINIT=n +CONFIG_EXAMPLES_USBMSC_TRACECLASS=n +CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS=n +CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER=n +CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n + +# +# Settings for examples/usbterm +# +# CONFIG_EXAMPLES_USBTERM_BUILTIN - Build the usbterm example as an NSH +# built-in command. NOTE: This is not fully functional as of this +# writing.. It should work, but there is no mechanism in place yet +# to exit the USB terminal program and return to NSH. +# CONFIG_EXAMPLES_USBTERM_DEVINIT - If defined, then the example will +# call a user provided function as part of its initialization: +# int usbterm_devinit(void); +# And another user provided function at termination: +# void usbterm_devuninit(void); +# CONFIG_EXAMPLES_USBTERM_BUFLEN - The size of the input and output +# buffers used for receiving data. Default 256 bytes. +# +# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB, or +# CONFIG_USBDEV_TRACE), then the example code will also manage the USB trace +# output. The amount of trace output can be controlled using: +# +# CONFIG_EXAMPLES_USBTERM_TRACEINIT +# Show initialization events +# CONFIG_EXAMPLES_USBTERM_TRACECLASS +# Show class driver events +# CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS +# Show data transfer events +# CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER +# Show controller events +# CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS +# Show interrupt-related events. +# +CONFIG_EXAMPLES_USBTERM_BUILTIN=y +CONFIG_EXAMPLES_USBTERM_DEVINIT=y +#CONFIG_EXAMPLES_USBTERM_BUFLEN +CONFIG_EXAMPLES_USBTERM_TRACEINIT=n +CONFIG_EXAMPLES_USBTERM_TRACECLASS=n +CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS=n +CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER=n +CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS=n + +# +# Settings for examples/cdcacm +# +# Configuration prequisites: +# +# CONFIG_USBDEV=y : USB device support must be enabled +# CONFIG_CDCACM=y : The CDC/ACM driver must be built +# CONFIG_NSH_BUILTIN_APPS : NSH built-in application support must be enabled +# +# Configuration options specific to this example: +# +# CONFIG_EXAMPLES_CDCACM_DEVMINOR +# The minor number of the CDC/ACM device. +# CONFIG_EXAMPLES_CDCACM_TRACEINIT +# Show initialization events +# CONFIG_EXAMPLES_CDCACM_TRACECLASS +# Show class driver events +# CONFIG_EXAMPLES_CDCACM_TRACETRANSFERS +# Show data transfer events +# CONFIG_EXAMPLES_CDCACM_TRACECONTROLLER +# Show controller events +# CONFIG_EXAMPLES_CDCACM_TRACEINTERRUPTS +# Show interrupt-related events. +# +CONFIG_EXAMPLES_CDCACM_DEVMINOR=0 +CONFIG_EXAMPLES_CDCACM_TRACEINIT=n +CONFIG_EXAMPLES_CDCACM_TRACECLASS=n +CONFIG_EXAMPLES_CDCACM_TRACETRANSFERS=n +CONFIG_EXAMPLES_CDCACM_TRACECONTROLLER=n +CONFIG_EXAMPLES_CDCACM_TRACEINTERRUPTS=n + +# +# Stack and heap information +# +# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP +# operation from FLASH but must copy initialized .data sections to RAM. +# (should also be =n for the PIC32MX which always runs from flash) +# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH +# but copy themselves entirely into RAM for better performance. +# CONFIG_CUSTOM_STACK - The up_ implementation will handle +# all stack operations outside of the nuttx model. +# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) +# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. +# This is the thread that (1) performs the inital boot of the system up +# to the point where user_start() is spawned, and (2) there after is the +# IDLE thread that executes only when there is no other thread ready to +# run. +# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate +# for the main user thread that begins at the user_start() entry point. +# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size +# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size +# CONFIG_HEAP_BASE - The beginning of the heap +# CONFIG_HEAP_SIZE - The size of the heap +# +CONFIG_BOOT_RUNFROMFLASH=n +CONFIG_BOOT_COPYTORAM=n +CONFIG_CUSTOM_STACK=n +CONFIG_STACK_POINTER= +CONFIG_IDLETHREAD_STACKSIZE=2048 +CONFIG_USERMAIN_STACKSIZE=2048 +CONFIG_PTHREAD_STACK_MIN=256 +CONFIG_PTHREAD_STACK_DEFAULT=2048 +CONFIG_HEAP_BASE= +CONFIG_HEAP_SIZE= diff --git a/nuttx/configs/pic32-starterkit/nsh2/ld.script b/nuttx/configs/pic32-starterkit/nsh2/ld.script new file mode 100644 index 000000000..1f07ee651 --- /dev/null +++ b/nuttx/configs/pic32-starterkit/nsh2/ld.script @@ -0,0 +1,317 @@ +/**************************************************************************** + * configs/pic32-starterkit/nsh2/ld.script + * + * Copyright (C) 2012 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt <gnutt@nuttx.org> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ +/* Memory Regions ***********************************************************/ + +MEMORY +{ + /* The PIC32MX795F512L has 512Kb of program FLASH at physical address + * 0x1d000000 but is always accessed at KSEG0 address 0x9d00:0000 + */ + + kseg0_progmem (rx) : ORIGIN = 0x9d000000, LENGTH = 512K + + /* The PIC32MX795F512L has 12Kb of boot FLASH at physical address + * 0x1fc00000. The initial reset vector is in KSEG1, but all other + * accesses are in KSEG0. + * + * REGION PHYSICAL KSEG SIZE + * DESCRIPTION START ADDR (BYTES) + * ------------- ---------- ------ ---------------------- + * Exceptions:* + * Reset 0x1fc00000 KSEG1 512 512 + * TLB Refill 0x1fc00200 KSEG1 256 768 + * Cache Error 0x1fc00300 KSEG1 128 896 + * Others 0x1fc00380 KSEG1 128 1024 (1Kb) + * Interrupt 0x1fc00400 KSEG1 128 1152 + * JTAG 0x1fc00480 KSEG1 16 1168 + * Exceptions 0x1fc00490 KSEG0 8192-1168 8192 (4Kb) + * Debug code 0x1fc02000 KSEG1 4096-16 12272 + * DEVCFG3-0 0x1fc02ff0 KSEG1 16 12288 (12Kb) + * + * Exceptions assume: + * + * STATUS: BEV=0/1 and EXL=0 + * CAUSE: IV=1 + * JTAG: ProbEn=0 + * And multi-vector support disabled + */ + + kseg1_reset (rx) : ORIGIN = 0xbfc00000, LENGTH = 384 + kseg1_genexcpt (rx) : ORIGIN = 0xbfc00180, LENGTH = 128 + kseg1_ebexcpt (rx) : ORIGIN = 0xbfc00200, LENGTH = 128 + kseg1_bevexcpt (rx) : ORIGIN = 0xbfc00380, LENGTH = 128 + kseg1_intexcpt (rx) : ORIGIN = 0xbfc00400, LENGTH = 128 + kseg1_dbgexcpt (rx) : ORIGIN = 0xbfc00480, LENGTH = 16 + kseg0_bootmem (rx) : ORIGIN = 0x9fc00490, LENGTH = 8192-1168 + kseg1_dbgcode (rx) : ORIGIN = 0xbfc02000, LENGTH = 4096-16 + kseg1_devcfg (r) : ORIGIN = 0xbfc02ff0, LENGTH = 16 + + /* The PIC32MX795F512L has 128Kb of data memory at physical address + * 0x00000000. Since the PIC32MX has no data cache, this memory is + * always accessed through KSEG1. + * + * When used with MPLAB, we need to set aside 512 bytes of memory + * for use by MPLAB. + */ + + kseg1_datamem (w!x) : ORIGIN = 0xa0000200, LENGTH = 128K - 512 +} + +OUTPUT_FORMAT("elf32-tradlittlemips") +OUTPUT_ARCH(pic32mx) +ENTRY(__start) + +SECTIONS +{ + /* Boot FLASH sections */ + + .reset : + { + KEEP (*(.reset)) + } > kseg1_reset + + /* Exception handlers. The following is assumed: + * + * STATUS: BEV=1 and EXL=0 + * CAUSE: IV=1 + * JTAG: ProbEn=0 + * And multi-vector support disabled + * + * In that configuration, the vector locations become: + * + * Reset, Soft Reset bfc0:0000 + * TLB Refill bfc0:0200 + * Cache Error bfc0:0300 + * All others bfc0:0380 + * Interrupt bfc0:0400 + * EJTAG Debug bfc0:0480 + */ + + /* KSEG1 exception handler "trampolines" */ + + .gen_excpt : + { + KEEP (*(.gen_excpt)) + } > kseg1_genexcpt + + .ebase_excpt : + { + KEEP (*(.ebase_excpt)) + } > kseg1_ebexcpt + + .bev_excpt : + { + KEEP (*(.bev_excpt)) + } > kseg1_bevexcpt + + .int_excpt : + { + KEEP (*(.int_excpt)) + } > kseg1_intexcpt + + .dbg_excpt = ORIGIN(kseg1_dbgexcpt); + + .start : + { + /* KSEG0 Reset startup logic */ + + *(.start) + + /* KSEG0 exception handlers */ + + *(.nmi_handler) + *(.bev_handler) + *(.int_handler) + } > kseg0_bootmem + + .dbg_code = ORIGIN(kseg1_dbgcode); + + .devcfg : + { + KEEP (*(.devcfg)) + } > kseg1_devcfg + + /* Program FLASH sections */ + + .text : + { + _stext = ABSOLUTE(.); + *(.text .text.*) + *(.stub) + KEEP (*(.text.*personality*)) + *(.gnu.linkonce.t.*) + *(.gnu.warning) + *(.mips16.fn.*) + *(.mips16.call.*) + + /* Read-only data is included in the text section */ + + *(.rodata .rodata.*) + *(.rodata1) + *(.gnu.linkonce.r.*) + + /* Small initialized constant global and static data */ + + *(.sdata2 .sdata2.*) + *(.gnu.linkonce.s2.*) + + /* Uninitialized constant global and static data */ + + *(.sbss2 .sbss2.*) + *(.gnu.linkonce.sb2.*) + _etext = ABSOLUTE(.); + } > kseg0_progmem + + /* Initialization data begins here in progmem */ + + _data_loaddr = LOADADDR(.data); + + .eh_frame_hdr : { *(.eh_frame_hdr) } + .eh_frame : ONLY_IF_RO { KEEP (*(.eh_frame)) } + + /* RAM functions are positioned at the beginning of RAM so that + * they can be guaranteed to satisfy the 2Kb alignment requirement. + */ + +/* This causes failures if there are no RAM functions + .ramfunc ALIGN(2K) : + { + _sramfunc = ABSOLUTE(.); + *(.ramfunc .ramfunc.*) + _eramfunc = ABSOLUTE(.); + } > kseg1_datamem AT > kseg0_progmem + + _ramfunc_loadaddr = LOADADDR(.ramfunc); + _ramfunc_sizeof = SIZEOF(.ramfunc); + _bmxdkpba_address = _sramfunc - ORIGIN(kseg1_datamem) ; + _bmxdudba_address = LENGTH(kseg1_datamem) ; + _bmxdupba_address = LENGTH(kseg1_datamem) ; +*/ + + .data : + { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + KEEP (*(.gnu.linkonce.d.*personality*)) + *(.data1) + } > kseg1_datamem AT > kseg0_progmem + + .eh_frame : ONLY_IF_RW { KEEP (*(.eh_frame)) } + _gp = ALIGN(16) + 0x7FF0 ; + + .got : + { + *(.got.plt) *(.got) + } > kseg1_datamem AT > kseg0_progmem + + .sdata : + { + *(.sdata .sdata.* .gnu.linkonce.s.*) + } > kseg1_datamem AT > kseg0_progmem + + .lit8 : + { + *(.lit8) + } > kseg1_datamem AT > kseg0_progmem + + .lit4 : + { + *(.lit4) + _edata = ABSOLUTE(.); + } >kseg1_datamem AT>kseg0_progmem + + .sbss : + { + _sbss = ABSOLUTE(.); + *(.dynsbss) + *(.sbss .sbss.* .gnu.linkonce.sb.*) + *(.scommon) + } >kseg1_datamem + + .bss : + { + *(.dynbss) + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + _ebss = ABSOLUTE(.); + } > kseg1_datamem + + /* Stabs debugging sections */ + + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + + /* DWARF debug sections */ + /* DWARF 1 */ + + .debug 0 : { *(.debug) } + .line 0 : { *(.line) } + + /* GNU DWARF 1 extensions */ + + .debug_srcinfo 0 : { *(.debug_srcinfo) } + .debug_sfnames 0 : { *(.debug_sfnames) } + + /* DWARF 1.1 and DWARF 2 */ + + .debug_aranges 0 : { *(.debug_aranges) } + .debug_pubnames 0 : { *(.debug_pubnames) } + + /* DWARF 2 */ + + .debug_info 0 : { *(.debug_info .gnu.linkonce.wi.*) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_line 0 : { *(.debug_line) } + .debug_frame 0 : { *(.debug_frame) } + .debug_str 0 : { *(.debug_str) } + .debug_loc 0 : { *(.debug_loc) } + .debug_macinfo 0 : { *(.debug_macinfo) } + + /* SGI/MIPS DWARF 2 extensions */ + + .debug_weaknames 0 : { *(.debug_weaknames) } + .debug_funcnames 0 : { *(.debug_funcnames) } + .debug_typenames 0 : { *(.debug_typenames) } + .debug_varnames 0 : { *(.debug_varnames) } + + /DISCARD/ : { *(.note.GNU-stack) } +} diff --git a/nuttx/configs/pic32-starterkit/nsh2/setenv.sh b/nuttx/configs/pic32-starterkit/nsh2/setenv.sh new file mode 100755 index 000000000..724a0a67e --- /dev/null +++ b/nuttx/configs/pic32-starterkit/nsh2/setenv.sh @@ -0,0 +1,61 @@ +#!/bin/bash +# configs/pic32-starterkit/nsh2/setenv.sh +# +# Copyright (C) 2012 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# + +if [ "$_" = "$0" ] ; then + echo "You must source this script, not run it!" 1>&2 + exit 1 +fi + +if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi + +WD=`pwd` +if [ ! -x "setenv.sh" ]; then + echo "This script must be executed from the top-level NuttX build directory" + exit 1 +fi + +# This the Cygwin path to the location where I installed the MicroChip +# PIC32MX toolchain under windows. This is *not* the default install +# location so you will probably have to edit this. You will also have +# to edit this if you install a different version of if you install +# the Linux PIC32MX toolchain as well +export TOOLCHAIN_BIN="/cygdrive/c/MicroChip/mplabc32/v1.12/bin" + +# This is the path to the tools subdirectory +export PIC32TOOL_DIR="${WD}/configs/pic32-starterkit/tools" + +# Add the path to the toolchain to the PATH varialble +export PATH="${TOOLCHAIN_BIN}:${PIC32TOOL_DIR}:/sbin:/usr/sbin:${PATH_ORIG}" + +echo "PATH : ${PATH}" diff --git a/nuttx/configs/stm3240g-eval/README.txt b/nuttx/configs/stm3240g-eval/README.txt index 4b902802b..33cf7f39e 100755 --- a/nuttx/configs/stm3240g-eval/README.txt +++ b/nuttx/configs/stm3240g-eval/README.txt @@ -905,12 +905,12 @@ Where <subdir> is one of the following: nsh2: ----- - This is an alternaitve NSH configuration. One limitation of the STM3240G-EVAL + This is an alternative NSH configuration. One limitation of the STM3240G-EVAL board is that you cannot have both a UART-based NSH console and SDIO support. The nsh2 differs from the nsh configuration in the following ways: -CONFIG_STM32_USART3=y : USART3 is disabled - + CONFIG_STM32_USART3=n + +CONFIG_STM32_USART3=n -CONFIG_STM32_SDIO=n : SDIO is enabled +CONFIG_STM32_SDIO=y |