1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
|
/****************************************************************************
* configs/lpc4330-xplorer/include/board.h
* include/arch/board/board.h
*
* Copyright (C) 2012 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#ifndef __ARCH_BOARD_BOARD_H
#define __ARCH_BOARD_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdbool.h>
#if defined(CONFIG_ARCH_IRQBUTTONS) && defined(CONFIG_GPIO_IRQ)
# include <nuttx/irq.h>
#endif
/****************************************************************************
* Definitions
****************************************************************************/
/* Clocking ****************************************************************/
/* NOTE: The following definitions require lpc43_cgu.h. It is not included
* here because the including C file may not have that file in its include
* path.
*
* The Xplorer board has four crystals on board:
*
* Y1 - RTC 32.768 MHz oscillator input,
* Y2 - 24.576 MHz input to the UDA 1380 audio codec,
* Y3 - 12.000 MHz LPC43xx crystal oscillator input
* Y4 - 50 MHz input for Ethernet
*/
#define BOARD_XTAL_FREQUENCY (12000000) /* XTAL oscillator frequency (Y3) */
#define BOARD_RTCCLK_FREQUENCY (32768) /* RTC oscillator frequency (Y1) */
#define BOARD_INTRCOSC_FREQUENCY (4000000) /* Internal RC oscillator frequency */
/* Integer and direct modes are supported:
*
* In integer mode:
* Fclkin = BOARD_XTAL_FREQUENCY
* Fclkout = Msel * FClkin / Nsel
* Fcco = 2 * Psel * Nclkout
* In direct mode:
* Fclkin = BOARD_XTAL_FREQUENCY
* Fclkout = Msel * FClkin / Nsel
* Fcco = Fclkout
*/
#undef BOARD_PLL1_DIRECT /* Integer mode */
#define BOARD_PLL_MSEL (6) /* Msel = 6 */
#define BOARD_PLL_NSEL (1) /* Nsel = 1 */
#define BOARD_PLL_PSEL (2) /* Psel = 2 */
#define BOARD_FCLKOUT_FREQUENCY (72000000) /* 6 * 12,000,000 / 1 */
#define BOARD_FCCO_FREQUENCY (244000000) /* 2 * 2 * 72,000,000 */
/* This is the clock setup we configure for:
*
* SYSCLK = BOARD_OSCCLK_FREQUENCY = 12MHz -> Select Main oscillator for source
* PLL0CLK = (2 * 20 * SYSCLK) / 1 = 480MHz -> PLL0 multipler=20, pre-divider=1
* CCLCK = 480MHz / 6 = 80MHz -> CCLK divider = 6
*/
#define LPC43_CCLK BOARD_FCLKOUT_FREQUENCY
/* UART clocking ***********************************************************/
/* Configure all U[S]ARTs to use the XTAL input frequency */
#define BOARD_USART0_CLKSRC BASE_USART0_CLKSEL_XTAL
#define BOARD_USART0_BASEFREQ BOARD_XTAL_FREQUENCY
#define BOARD_UART1_CLKSRC BASE_UART1_CLKSEL_XTAL
#define BOARD_UART1_BASEFREQ BOARD_XTAL_FREQUENCY
#define BOARD_USART2_CLKSRC BASE_USART2_CLKSEL_XTAL
#define BOARD_USART3_BASEFREQ BOARD_XTAL_FREQUENCY
#define BOARD_USART3_CLKSRC BASE_USART3_CLKSEL_XTAL
#define BOARD_USART3_BASEFREQ BOARD_XTAL_FREQUENCY
/* LED definitions *********************************************************/
/* The LPC4330-Xplorer has 2 user-controllable LEDs labeled D2 an D3 in the
* schematic and on but referred to has LED1 and LED2 here, respectively.
*
* LED1 D2 GPIO1[12]
* LED2 D3 GPIO1[11]
*
* LEDs are pulled high to a low output illuminates the LED.
*
* LED index values for use with lpc43_setled()
*/
#define BOARD_LED1 0
#define BOARD_LED2 1
#define BOARD_NLEDS 2
/* LED bits for use with lpc43_setleds() */
#define BOARD_LED1_BIT (1 << BOARD_LED1)
#define BOARD_LED2_BIT (1 << BOARD_LED2)
/* If CONFIG_ARCH_LEDS is defined, the LEDs will be controlled as follows
* for NuttX debug functionality (where NC means "No Change"). If
* CONFIG_ARCH_LEDS is not defined, then the LEDs are completely under
* control of the application. The following interfaces are then available
* for application control of the LEDs:
*
* void lpc43_ledinit(void);
* void lpc43_setled(int led, bool ledon);
* void lpc43_setleds(uint8_t ledset);
*/
/* ON OFF */
/* LED1 LED2 LED1 LED2 */
#define LED_STARTED 0 /* OFF OFF - - */
#define LED_HEAPALLOCATE 1 /* ON OFF - - */
#define LED_IRQSENABLED 1 /* ON OFF - - */
#define LED_STACKCREATED 1 /* ON OFF - - */
#define LED_INIRQ 2 /* NC ON NC OFF */
#define LED_SIGNAL 2 /* NC ON NC OFF */
#define LED_ASSERTION 2 /* NC ON NC OFF */
#define LED_PANIC 2 /* NC ON NC OFF */
/* UART Pins ****************************************************************/
/* The LPC4330 Xplorer does not have RS-232 drivers or serial connectors on
* board. USART0 and UART1 are available on J8 as follows:
*
* ------ ------ -----------------------
* SIGNAL J8 PIN LPC4330FET100 PIN
* (TFBGA100 package)
* ------ ------ -----------------------
* U0_TXD pin 9 F6 P6_4 U0_TXD=Alt 2
* U0_RXD pin 10 F9 P6_5 U0_RXD=Alt 2
* U1_TXD pin 13 H8 P1_13 U1_TXD=Alt 1
* U1_RXD pin 14 J8 P1_14 U1_RXD=Alt 1
* ------ ------ -----------------------
*
* The following definitions must be provided so that the LPC43 serial
* driver can set up the U[S]ART for the serial console properly (see the
* file arch/arc/src/lpc43xx/lpc4310203050_pinconf.h for more info).
*/
#define PINCONF_U0_TXD PINCONF_U0_TXD_3
#define PINCONF_U0_RXD PINCONF_U0_RXD_3
#define PINCONF_U1_TXD PINCONF_U1_TXD_1
#define PINCONF_U1_RXD PINCONF_U1_RXD_1
/****************************************************************************
* Public Types
****************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************
* Public Data
****************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
/****************************************************************************
* Name: lpc43_boardinitialize
*
* Description:
* All LPC43xx architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
****************************************************************************/
EXTERN void lpc43_boardinitialize(void);
/*****************************************************************************
* Name: lpc43_ledinit, lpc43_setled, and lpc43_setleds
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board
* LEDs. If CONFIG_ARCH_LEDS is not defined, then the following interfaces
* are available to control the LEDs from user applications.
*
****************************************************************************/
#ifndef CONFIG_ARCH_LEDS
EXTERN void lpc43_ledinit(void);
EXTERN void lpc43_setled(int led, bool ledon);
EXTERN void lpc43_setleds(uint8_t ledset);
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_BOARD_BOARD_H */
|
