1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
/************************************************************************************
* configs/sam3uek_eval/src/sam4l-xplained.h
*
* Copyright (C) 2009-2011, 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_SAM4L_XPLAINED_SRC_SAM4L_XPLAINED_H
#define __CONFIGS_SAM4L_XPLAINED_SRC_SAM4L_XPLAINED_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
#include <arch/irq.h>
#include <nuttx/irq.h>
#include "chip/sam_pinmap.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* LEDs: There are three LEDs on board the SAM4L Xplained Pro board: The EDBG
* controls two of the LEDs, a power LED and a status LED. There is only
* one user controllable LED, a yellow LED labeled LED0 near the SAM4L USB
* connector.
*
* This LED is controlled by PC07 and LED0 can be activated by driving the
* PC07 to GND.
*
* When CONFIG_ARCH_LEDS is defined in the NuttX configuration, NuttX will
* control LED0 as follows:
*
* SYMBOL Meaning LED0
* ------------------- ----------------------- ------
* LED_STARTED NuttX has been started OFF
* LED_HEAPALLOCATE Heap has been allocated OFF
* LED_IRQSENABLED Interrupts enabled OFF
* LED_STACKCREATED Idle stack created ON
* LED_INIRQ In an interrupt N/C
* LED_SIGNAL In a signal handler N/C
* LED_ASSERTION An assertion failed N/C
* LED_PANIC The system has crashed FLASH
*
* Thus is LED0 is statically on, NuttX has successfully booted and is,
* apparently, running normmally. If LED0 is flashing at approximately
* 2Hz, then a fatal error has been detected and the system has halted.
*/
#define GPIO_LED0 (GPIO_OUTPUT | GPIO_PULL_NONE GPIO_OUTPUT_SET | \
GPIO_PORTC | GPIO_PIN7)
/* QTouch button: The SAM4L Xplained Pro kit has one QTouch button. The connection
* to the SAM4L is:
*
* PC13 CATB_SENSE15
* PC14 CATB_DIS
*/
/* Mechanical buttons:
*
* The SAM4L Xplained Pro contains two mechanical buttons. One button is the
* RESET button connected to the SAM4L reset line and the other is a generic user
* configurable button. When a button is pressed it will drive the I/O line to GND.
*
* PC24 SW0
*/
#define GPIO_SW0 (GPIO_INPUT | GPIO_PULL_UP | GPIO_GLITCH_FILTER | \
GPIO_PORTC | GPIO_PIN24)
#define IRQ_SW0 SAM_IRQ_PC24
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Public data
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Functions
************************************************************************************/
/************************************************************************************
* Name: sam_spiinitialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the SAM3U-EK board.
*
************************************************************************************/
void weak_function sam_spiinitialize(void);
/****************************************************************************
* Name: up_ledinit
****************************************************************************/
#ifdef CONFIG_ARCH_LEDS
void up_ledinit(void);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_SAM4L_XPLAINED_SRC_SAM4L_XPLAINED_H */
|
