1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
|
README
======
This README discusses issues unique to NuttX configurations for the
STMicro STM32F4 Discovery development board.
Contents
========
- Development Environment
- GNU Toolchain Options
- IDEs
- NuttX buildroot Toolchain
- LEDs
- PWM
- UARTs
- Timer Inputs/Outputs
- FPU
- STM32F4Discovery-specific Configuration Options
- Configurations
Development Environment
=======================
Either Linux or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems. Testing was performed using the Cygwin
environment because the Raisonance R-Link emulatator and some RIDE7 development tools
were used and those tools works only under Windows.
GNU Toolchain Options
=====================
Toolchain Configurations
------------------------
The NuttX make system has been modified to support the following different
toolchain options.
1. The CodeSourcery GNU toolchain,
2. The Atollic Toolchain,
3. The devkitARM GNU toolchain,
4. Raisonance GNU toolchain, or
5. The NuttX buildroot Toolchain (see below).
All testing has been conducted using the CodeSourcery toolchain for Windows. To use
the Atollic, devkitARM, Raisonance GNU, or NuttX buildroot toolchain, you simply need to
add one of the following configuration options to your .config (or defconfig)
file:
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_STM32_ATOLLIC=y : Atollic toolchain under Windows
CONFIG_STM32_DEVKITARM=y : devkitARM under Windows
CONFIG_STM32_RAISONANCE=y : Raisonance RIDE7 under Windows
CONFIG_STM32_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
If you change the default toolchain, then you may also have to modify the PATH in
the setenv.h file if your make cannot find the tools.
NOTE: the CodeSourcery (for Windows), Atollic, devkitARM, and Raisonance toolchains are
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had no effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:
make clean_context all
An alias in your .bashrc file might make that less painful.
3. Dependencies are not made when using Windows versions of the GCC. This is
because the dependencies are generated using Windows pathes which do not
work with the Cygwin make.
Support has been added for making dependencies with the windows-native toolchains.
That support can be enabled by modifying your Make.defs file as follows:
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
If you have problems with the dependency build (for example, if you are not
building on C:), then you may need to modify tools/mkdeps.sh
The CodeSourcery Toolchain (2009q1)
-----------------------------------
The CodeSourcery toolchain (2009q1) does not work with default optimization
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
-Os.
The Atollic "Lite" Toolchain
----------------------------
The free, "Lite" version of the Atollic toolchain does not support C++ nor
does it support ar, nm, objdump, or objdcopy. If you use the Atollic "Lite"
toolchain, you will have to set:
CONFIG_HAVE_CXX=n
In order to compile successfully. Otherwise, you will get errors like:
"C++ Compiler only available in TrueSTUDIO Professional"
The make may then fail in some of the post link processing because of some of
the other missing tools. The Make.defs file replaces the ar and nm with
the default system x86 tool versions and these seem to work okay. Disable all
of the following to avoid using objcopy:
CONFIG_RRLOAD_BINARY=n
CONFIG_INTELHEX_BINARY=n
CONFIG_MOTOROLA_SREC=n
CONFIG_RAW_BINARY=n
Another problem that I had with the Atollic toolchain is that the provide a gcc.exe
and g++.exe in the same bin/ file as their ARM binaries. If the Atollic bin/ path
appears in your PATH variable before /usr/bin, then you will get the wrong gcc
when you try to build host executables. This will cause to strange, uninterpretable
errors build some host binaries in tools/ when you first make. Here is my
workaround kludge.
1. Edit the setenv.sh to put the Atollic toolchain at the beginning of the PATH
2. Source the setenv.sh file: . ./setenv.sh. A side effect of this is that it
will set an environment variable called PATH_ORIG.
3. Then go back to the original patch: export PATH=$PATH_ORIG
4. Then make. The make will build all of the host executable but will fail
when it gets to the first ARM binary.
5. Then source setenv.sh again: . ./setenv.sh. That will correct the PATH
again. When you do make again, the host executables are already made and
now the correct PATH is in place for the ARM build.
Also, the Atollic toolchain is the only toolchain that has built-in support for
the FPU in these configurations. If you plan to use the Cortex-M4 FPU, you will
need to use the Atollic toolchain for now. See the FPU section below for more
information.
devkitARM
---------
The devkitARM toolchain includes a version of MSYS make. Make sure that the
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
path or will get the wrong version of make.
IDEs
====
NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project.
Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).
Native Build
------------
Here are a few tips before you start that effort:
1) Select the toolchain that you will be using in your .config file
2) Start the NuttX build at least one time from the Cygwin command line
before trying to create your project. This is necessary to create
certain auto-generated files and directories that will be needed.
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
4) All assembly files need to have the definition option -D __ASSEMBLY__
on the command line.
Startup files will probably cause you some headaches. The NuttX startup file
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
one time from the Cygwin command line in order to obtain the pre-built
startup object needed by RIDE.
NuttX buildroot Toolchain
=========================
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
different from the default in your PATH variable).
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
This GNU toolchain builds and executes in the Linux or Cygwin environment.
1. You must have already configured Nuttx in <some-dir>/nuttx.
cd tools
./configure.sh STM32F4Discovery/<sub-dir>
2. Download the latest buildroot package into <some-dir>
3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
4. cd <some-dir>/buildroot
5. cp configs/cortexm3-defconfig-4.3.3 .config
6. make oldconfig
7. make
8. Edit setenv.h, if necessary, so that the PATH variable includes
the path to the newly built binaries.
See the file configs/README.txt in the buildroot source tree. That has more
detailed PLUS some special instructions that you will need to follow if you are
building a Cortex-M3 toolchain for Cygwin under Windows.
LEDs
====
The STM32F4Discovery board has four LEDs; green, organge, red and blue on the
board.. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/up_leds.c. The LEDs are used to encode OS-related
events as follows:
SYMBOL Meaning LED1* LED2 LED3 LED4
green orange red blue
------------------- ----------------------- ------- ------- ------- ------
LED_STARTED NuttX has been started ON OFF OFF OFF
LED_HEAPALLOCATE Heap has been allocated OFF ON OFF OFF
LED_IRQSENABLED Interrupts enabled ON ON OFF OFF
LED_STACKCREATED Idle stack created OFF OFF ON OFF
LED_INIRQ In an interrupt** ON N/C N/C OFF
LED_SIGNAL In a signal handler*** N/C ON N/C OFF
LED_ASSERTION An assertion failed ON ON N/C OFF
LED_PANIC The system has crashed N/C N/C N/C ON
LED_IDLE STM32 is is sleep mode (Optional, not used)
* If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot
and these LEDs will give you some indication of where the failure was
** The normal state is LED3 ON and LED1 faintly glowing. This faint glow
is because of timer interupts that result in the LED being illuminated
on a small proportion of the time.
*** LED2 may also flicker normally if signals are processed.
PWM
===
The STM32F4Discovery has no real on-board PWM devices, but the board can be
configured to output a pulse train using TIM4 CH2 on PD3. This pin is
available next to the audio jack.
UART
====
UART/USART PINS
---------------
USART1
CK PA8
CTS PA11*
RTS PA12*
RX PA10*, PB7
TX PA9*, PB6*
USART2
CK PA4*, PD7
CTS PA0*, PD3
RTS PA1, PD4*
RX PA3, PD6
TX PA2, PD5*
USART3
CK PB12, PC12*, PD10
CTS PB13, PD11
RTS PB14, PD12*
RX PB11, PC11, PD9
TX PB10*, PC10*, PD8
UART4
RX PA1, PC11
TX PA0*, PC10*
UART5
RX PD2
TX PC12*
USART6
CK PC8, PG7**
CTS PG13**, PG15**
RTS PG12**, PG8**
RX PC7*, PG9**
TX PC6, PG14**
* Indicates pins that have other on-board functins and should be used only
with care (See table 5 in the STM32F4Discovery User Guide). The rest are
free I/O pins.
** Port G pins are not supported by the MCU
Default USART/UART Configuration
--------------------------------
USART2 is enabled in all configurations (see */defconfig). RX and TX are
configured on pins PA3 and PA2, respectively (see include/board.h).
Timer Inputs/Outputs
====================
TIM1
CH1 PA8, PE9
CH2 PA9*, PE11
CH3 PA10*, PE13
CH4 PA11*, PE14
TIM2
CH1 PA0*, PA15, PA5*
CH2 PA1, PB3*
CH3 PA2, PB10*
CH4 PA3, PB11
TIM3
CH1 PA6*, PB4, PC6
CH2 PA7*, PB5, PC7*
CH3 PB0, PC8
CH4 PB1, PC9
TIM4
CH1 PB6*, PD12*
CH2 PB7, PD13*
CH3 PB8, PD14*
CH4 PB9*, PD15*
TIM5
CH1 PA0*, PH10**
CH2 PA1, PH11**
CH3 PA2, PH12**
CH4 PA3, PI0
TIM8
CH1 PC6, PI5
CH2 PC7*, PI6
CH3 PC8, PI7
CH4 PC9, PI2
TIM9
CH1 PA2, PE5
CH2 PA3, PE6
TIM10
CH1 PB8, PF6
TIM11
CH1 PB9*, PF7
TIM12
CH1 PH6**, PB14
CH2 PC15, PH9**
TIM13
CH1 PA6*, PF8
TIM14
CH1 PA7*, PF9
* Indicates pins that have other on-board functins and should be used only
with care (See table 5 in the STM32F4Discovery User Guide). The rest are
free I/O pins.
** Port H pins are not supported by the MCU
Quadrature Encode Timer Inputs
------------------------------
If enabled (by setting CONFIG_QENCODER=y), then quadrature encoder will
user TIM2 (see nsh/defconfig) and input pins PA15, and PA1 for CH1 and
CH2, respectively (see include board.h).
FPU
===
FPU Configuration Options
-------------------------
There are two version of the FPU support built into the STM32 port.
1. Lazy Floating Point Register Save.
This is an untested implementation that saves and restores FPU registers
only on context switches. This means: (1) floating point registers are
not stored on each context switch and, hence, possibly better interrupt
performance. But, (2) since floating point registers are not saved,
you cannot use floating point operations within interrupt handlers.
This logic can be enabled by simply adding the following to your .config
file:
CONFIG_ARCH_FPU=y
2. Non-Lazy Floating Point Register Save
Mike Smith has contributed an extensive re-write of the ARMv7-M exception
handling logic. This includes verified support for the FPU. These changes
have not yet been incorporated into the mainline and are still considered
experimental. These FPU logic can be enabled with:
CONFIG_ARCH_FPU=y
CONFIG_ARMV7M_CMNVECTOR=y
You will probably also changes to the ld.script in if this option is selected.
This should work:
-ENTRY(_stext)
+ENTRY(__start) /* Treat __start as the anchor for dead code stripping */
+EXTERN(_vectors) /* Force the vectors to be included in the output */
CFLAGS
------
Only the Atollic toolchain has built-in support for the Cortex-M4 FPU. You will see
the following lines in each Make.defs file:
ifeq ($(CONFIG_STM32_ATOLLIC),y)
# Atollic toolchain under Windows
...
ifeq ($(CONFIG_ARCH_FPU),y)
ARCHCPUFLAGS = -mcpu=cortex-m4 -mthumb -march=armv7e-m -mfpu=fpv4-sp-d16 -mfloat-abi=hard
else
ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
endif
endif
If you are using a toolchain other than the Atollic toolchain, then to use the FPU
you will also have to modify the CFLAGS to enable compiler support for the ARMv7-M
FPU. As of this writing, there are not many GCC toolchains that will support the
ARMv7-M FPU.
As a minimum you will need to add CFLAG options to (1) enable hardware floating point
code generation, and to (2) select the FPU implementation. You might try the same
options as used with the Atollic toolchain in the Make.defs file:
ARCHCPUFLAGS = -mcpu=cortex-m4 -mthumb -march=armv7e-m -mfpu=fpv4-sp-d16 -mfloat-abi=hard
Configuration Changes
---------------------
Below are all of the configuration changes that I had to make to configs/stm3240g-eval/nsh2
in order to successfully build NuttX using the Atollic toolchain WITH FPU support:
-CONFIG_ARCH_FPU=y : Enable FPU support
+CONFIG_ARCH_FPU=n
-CONFIG_STM32_CODESOURCERYW=n : Disable the CodeSourcery toolchain
+CONFIG_STM32_CODESOURCERYW=y
-CONFIG_STM32_ATOLLIC=y : Enable the Atollic toolchain
+CONFIG_STM32_ATOLLIC=n
-CONFIG_INTELHEX_BINARY=n : Suppress generation FLASH download formats
+CONFIG_INTELHEX_BINARY=y
-CONFIG_HAVE_CXX=n : Suppress generation of C++ code
+CONFIG_HAVE_CXX=y
See the section above on Toolchains, NOTE 2, for explanations for some of
the configuration settings. Some of the usual settings are just not supported
by the "Lite" version of the Atollic toolchain.
STM32F4Discovery-specific Configuration Options
===============================================
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=arm
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_ARM=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_CORTEXM4=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP=stm32
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_STM32F407IG=y
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
configuration features.
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=STM32F4Discovery (for the STM32F4Discovery development board)
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_STM32F4_DISCOVERY=y
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
CONFIG_DRAM_START - The start address of installed DRAM
CONFIG_DRAM_START=0x20000000
CONFIG_DRAM_END - Last address+1 of installed RAM
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
CONFIG_ARCH_IRQPRIO - The STM3240xxx supports interrupt prioritization
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_FPU - The STM3240xxx supports a floating point unit (FPU)
CONFIG_ARCH_FPU=y
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
Individual subsystems can be enabled:
AHB1
----
CONFIG_STM32_CRC
CONFIG_STM32_BKPSRAM
CONFIG_STM32_CCMDATARAM
CONFIG_STM32_DMA1
CONFIG_STM32_DMA2
CONFIG_STM32_ETHMAC
CONFIG_STM32_OTGHS
AHB2
----
CONFIG_STM32_DCMI
CONFIG_STM32_CRYP
CONFIG_STM32_HASH
CONFIG_STM32_RNG
CONFIG_STM32_OTGFS
AHB3
----
CONFIG_STM32_FSMC
APB1
----
CONFIG_STM32_TIM2
CONFIG_STM32_TIM3
CONFIG_STM32_TIM4
CONFIG_STM32_TIM5
CONFIG_STM32_TIM6
CONFIG_STM32_TIM7
CONFIG_STM32_TIM12
CONFIG_STM32_TIM13
CONFIG_STM32_TIM14
CONFIG_STM32_WWDG
CONFIG_STM32_SPI2
CONFIG_STM32_SPI3
CONFIG_STM32_USART2
CONFIG_STM32_USART3
CONFIG_STM32_UART4
CONFIG_STM32_UART5
CONFIG_STM32_I2C1
CONFIG_STM32_I2C2
CONFIG_STM32_I2C3
CONFIG_STM32_CAN1
CONFIG_STM32_CAN2
CONFIG_STM32_DAC1
CONFIG_STM32_DAC2
CONFIG_STM32_PWR -- Required for RTC
APB2
----
CONFIG_STM32_TIM1
CONFIG_STM32_TIM8
CONFIG_STM32_USART1
CONFIG_STM32_USART6
CONFIG_STM32_ADC1
CONFIG_STM32_ADC2
CONFIG_STM32_ADC3
CONFIG_STM32_SDIO
CONFIG_STM32_SPI1
CONFIG_STM32_SYSCFG
CONFIG_STM32_TIM9
CONFIG_STM32_TIM10
CONFIG_STM32_TIM11
Timer and I2C devices may need to the following to force power to be applied
unconditionally at power up. (Otherwise, the device is powered when it is
initialized).
CONFIG_STM32_FORCEPOWER
Timer devices may be used for different purposes. One special purpose is
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
is defined (as above) then the following may also be defined to indicate that
the timer is intended to be used for pulsed output modulation, ADC conversion,
or DAC conversion. Note that ADC/DAC require two definition: Not only do you have
to assign the timer (n) for used by the ADC or DAC, but then you also have to
configure which ADC or DAC (m) it is assigned to.
CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,14
CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2
For each timer that is enabled for PWM usage, we need the following additional
configuration settings:
CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
NOTE: The STM32 timers are each capable of generating different signals on
each of the four channels with different duty cycles. That capability is
not supported by this driver: Only one output channel per timer.
JTAG Enable settings (by default only SW-DP is enabled):
CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
but without JNTRST.
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
STM3240xxx specific device driver settings
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
m (m=4,5) for the console and ttys0 (default is the USART1).
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_U[S]ARTn_2STOP - Two stop bits
STM3240xxx CAN Configuration
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
Standard 11-bit IDs.
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
mode for testing. The STM32 CAN driver does support loopback mode.
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an
dump of all CAN registers.
STM3240xxx SPI Configuration
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
support. Non-interrupt-driven, poll-waiting is recommended if the
interrupt rate would be to high in the interrupt driven case.
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
STM3240xxx DMA Configuration
CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
and CONFIG_STM32_DMA2.
CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
Default: Medium
CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
4-bit transfer mode.
Configurations
==============
Each STM32F4Discovery configuration is maintained in a sudirectory and
can be selected as follow:
cd tools
./configure.sh STM32F4Discovery/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following:
ostest:
------
This configuration directory, performs a simple OS test using
examples/ostest. By default, this project assumes that you are
using the DFU bootloader.
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. The
Configuration enables both the serial and telnet NSH interfaces.
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux / Mac OS X
NOTES:
1. This example supports the PWM test (apps/examples/pwm) but this must
be manually enabled by selecting:
CONFIG_PWM=y : Enable the generic PWM infrastructure
CONFIG_STM32_TIM4=y : Enable TIM4
CONFIG_STM32_TIM4_PWM=y : Use TIM4 to generate PWM output
See also apps/examples/README.txt
Special PWM-only debug options:
CONFIG_DEBUG_PWM
2. This example supports the Quadrature Encode test (apps/examples/qencoder)
but this must be manually enabled by selecting:
CONFIG_QENCODER=y : Enable the generic Quadrature Encoder infrastructure
CONFIG_STM32_TIM2=y : Enable TIM2
CONFIG_STM32_TIM2_QE=y : Use TIM2 as the quadrature encoder
See also apps/examples/README.txt
Special PWM-only debug options:
CONFIG_DEBUG_QENCODER
|